Search NASA⌕ Search

SEARCH · Search NASA

Results for “high temperature application”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High-Temperature Heat Transfer Fluid Circulator for Concentrating Solar Power Systems How Mohawk and Velo3Dare Printing the Future of Energy

A high temperature Heat Transfer Fluid circulator compressor with wide turn down ratio aerodynamic performance was designed, fabricated and tested for application with high pressure super Critical CO2 fluid capable of temperatures and pressures to >750°C and 25 MPa respectively. The modular system decoupled the drive motor system from an independent compressor shaft to provide thermal isolation between the high temperature compressor shaft and the lower temperature capable motor elements. While the thermal management approach appears to be viable there are potential losses in the secondary cooling flows that need to be taken into account and fine-tuned during operation in order to achieve desired overall system efficiencies. The system was also shown to be viable and dynamically stable throughout the entire operating speed range, thereby validating the overall system configuration and structural design approach used. Finally, while it was not possible to achieve specific PTC-10 test points, the compressor performance tests provide sufficient data to indicate that the compressor has the ability to achieve the required performance in practice. The two key factors affecting compressor design and cost are the maximum expected temperature and pressure. The maximum allowable temperatures for current state-of-the-art (SOA) motor driven compressor technology is limited to of approximately 150-200°C, but inlet temperatures >750 °C may be encountered. While the optimal efficiency of compression is in the transcritical region, some concepts require inlet pressures to 225 bar.

14 SOLAR ENERGY↗
DOE OSTI2021

Modeling in High Temperature Corrosion: A Review and Outlook

Realizing higher operating temperatures to increase efficiency of future applications for energy conversion and storage while minimizing cost is a challenge for development of high-temperature materials. Simultaneous optimization of mechanical properties and corrosion resistance continues to be a difficult task but is essential due to the need to significantly accelerate the transition between technology readiness levels in the future. Furthermore, oxidation-induced degradation will be a critical life-limiting mechanism at increased operating temperatures. Suitable high-temperature materials cannot be solely identified by time-consuming experiments and reliable computational methods incorporating the relevant physics of processes must be considered to complement the experimental efforts. In the present work, a review of the methods employed to model oxidation-induced material degradation described in literature will be discussed. Furthermore, their capability to predict lifetime and aid in material selection will be evaluated.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design rules for 316H nuclear components cladded with nickel or tungsten

The existing Class A metallic materials qualified in the ASME Boiler & Pressure Vessel Code Section III, Division 5 rules for high temperature nuclear reactors are not ideally suited for long term molten salt corrosion resistance in high temperature molten salt reactors. Potentially, corrosion or corrosion driven environmentally assisted cracking could limit the design life of structural components in molten salt reactors. A solution to this limitation is the use of cladded components – overlay the Class A material with a thin layer of some non-qualified, corrosion-resistant material. However, this necessitates the development of design methods for cladded components that do not require long-term testing of clad materials in order to support the near-term deployment of molten salt reactors. This report develops such a methodology along with a complete set of rules presented in a format compatible with an ASME nuclear Code Case. These design rules are for 316H Class A components cladded with either nickel or tungsten. The report also discusses the development of a set of general criteria for selecting clad materials beyond the specific 316H/tungsten and 316H/nickel systems and general acceptance tests for checking the mechanical integrity of the clad/base metal interface. Finally, the report includes a set of fully-documented sample problems detailing the application of the rules to high temperature cladded components

36 MATERIALS SCIENCE↗
DOE OSTI2021

High Temperature Acclimation of Leaf Gas Exchange, Photochemistry, and Metabolomic Profiles in Populus trichocarpa

High temperatures alter the thermal sensitivities of numerous physiological and biochemical processes that impact tree growth and productivity. Foliar and root applications of methanol have been implicated in plant acclimation to high temperature via the C 1 pathway. Here, we characterized temperature acclimation at 35°C of leaf gas exchange, chlorophyll fluorescence and extractable metabolites of potted Populus trichocarpa saplings and examined potential influences of mM concentrations of methanol added during soil watering over a two-month period. Relative to plants grown under the low growth temperature (LGT), high growth temperature (HGT) plants showed a suppression of leaf water use and carbon cycling including transpiration (E), net photosynthesis (P n ), an estimate of photorespiration (R p ), and dark respiration (R d ), attributed to reductions in stomatal conductance and direct negative effects on gas exchange and photosynthetic machinery. In contrast, HGT plants showed an upregulation of non-photochemical quenching (NPQ t ), the optimum temperature for ETR, and leaf isoprene emissions at 40°C. A large number of metabolites (867) were induced under HGT, many implicated in flavonoid biosynthesis highlighting a potentially protective role for these compounds. Methanol application did not significantly alter leaf gas exchange but slightly reduced the suppression of R d and R p by the high growth temperature while slightly impairing ETR, Fv’/Fm’, and q p . However, we were unable to determine if soil methanol was sufficiently taken up by the plant to have a direct effect on foliar processes. A small number of extracted leaf tissue metabolites (55 out of 10,015) showed significantly altered abundances under LGT and methanol treatments relative to water controls, and this increased in compound number (222) at the HGT. The results demonstrate the large physiological and biochemical impacts of high growth temperature on poplar seedlings and highlights the enhancement of the optimum temperature of ETR as a rapid thermal acclimation mechanism. Finally, although no large effect on leaf physiology was observed, the results are consistent with methanol both impairing photochemistry of the light reactions via formaldehyde toxicity, and stimulating photosynthesis and dark respiration through formate oxidation to CO 2 .

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

High-performance and stable AgSbTe 2 -based thermoelectric materials for near room temperature applications

AgSbTe 2 -based ternary chalcogenides show excellent thermoelectric performance at low- and middle-temperature ranges, yet their practical applications are greatly limited by their intrinsic poor thermodynamic stability. In this work, we demonstrate that AgSbTe 2 -based ternary chalcogenides can be stabilized for service below their decomposition threshold. A series of Ag x Sb 2-x Te 3-x (x = 1.0, 0.9, 0.8 and 0.7) samples have been prepared by the melt-quenching method. Among them, phase pure Ag 0.9 Sb 1.1 Te 2.1 is verified by comprehensive structural characterizations from macroscale by X-ray diffraction to microscale by energy-dispersive spectroscopy and then to sub-nanometer scale by atom probe tomography. This composition is further chosen for the stability investigation. The decomposition threshold of Ag 0.9 Sb 1.1 Te 2.1 appears around 473K. Below this temperature, the chemical compositions and thermoelectric properties are barely changed even after 720 h annealing at 473 K. The figure-of-merit (zT) value of Ag 0.9 Sb 1.1 Te 2.1 below the decomposition threshold is very competitive for real applications even compared with Bi 2 Te 3 -based alloys. The average zT of Ag 0.9 Sb 1.1 Te 2.1 at 300–473 K reaches 0.84, which is higher than most other thermoelectric materials in a similar temperature range, promising applications in miniaturized refrigeration and power generation near room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2019

High temperature steam oxidation of Cr-coated SiCf/SiC composite for LWR cladding applications

Chromium-coated silicon carbide fiber-reinforced ceramic matrix composites are potentially applicable to accident tolerant fuel cladding in light water reactors. Cr-coated silicon carbide composite, chemical vapor deposited silicon carbide, and pure Cr-metal were oxidized in 100% steam at atmospheric pressure for 4 hours using a thermogravimetric analyzer. Post-oxidation chemical analysis, phase identification and microstructural characterization indicates that the Cr coating layers did not adversely affect silicon carbide substrate under these conditions.

Lee, Yoonjo↗
DOE OSTI2022

Unveiling the Degradation Mechanism of High-Temperature Superconductor Bi 2 Sr 2 CaCu 2 O 8+δ in Water-Bearing Environments

We report the physical properties of copper oxide high-temperature superconductors have been studied extensively, such as its band structure, and doping effects of Bi 2 Sr 2 CaCu 2 O 8+δ (Bi-2212). However, some chemical-related properties of these superconductors are rarely reported, such as their stability in air. Here, we report experiments combined with ab initio calculations that address the effects of water in contact with Bi-2212. The evolution of Bi-2212 flake with exposure to water for different time intervals were tested and characterized by optical microscopy (OM), atomic force microscopy (AFM), Raman spectroscopy, transmission electron microscopy (TEM) and electrical measurements. The thickness of Bi-2212 flakes is gradually decreased in water, and some thin flakes can be completely etched away after a few days. The stability of Bi-2212 in other solvents is also evaluated, including alcohol, acetone, HCl and KOH. The morphology of Bi-2212 flakes is relatively stable in organic solvents. However, the flakes are etched relatively quick in HCl and KOH, especially in acidic environment. Our results imply that hydrogen ion is primarily responsible for the deterioration of their properties. Both TEM and calculation results demonstrate that the atoms in Bi-O plane is relatively stable when compared to the inner atoms in Sr-O, Ca-O and Cu-O planes. This work contributes towards understanding the chemical stability of Bi-2212 superconducting device in environmental medium, which is important for both fundamental studies and practical applications of copper oxide high-temperature superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Formulation of Conductive Inks for DIW Printed Battery Electrodes

Ink formulations for DIW printing of Li ion battery electrodes were optimized for high conductivity, surface area and printability. Our focus is particularly on optimizing Li-ion battery electrodes for low temperature applications by 3-D printing the cathodes into high surface area shapes. The sluggish kinetics of ion transport at the solid-electrolyte phase boundary can be a major problem in batteries at low temperatures, so optimizing for ion transport can help combat these issues. Two families of DIW ink were investigated; aqueous conductive polymer suspension with graphene nano platelets (GNP) ink, and “oil in water” graphene oxide (GO) micro emulsion ink which carbonizes to an open cell graphene aerogel. By iterative formulation changes, the conductivity of PEDOT:PSS based ink was increased over tenfold, and stiffness of GO emulsion ink was increased to provide better printability without sacrificing porosity.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multiscale Porous High-temperature Heat Exchanger Using Ceramic Co-extrusion

In this project, our MIT, Purdue, and GE team aims to design, model, fabricate, and test a novel high temperature, compact, and durable ceramic heat exchanger to be operated under high temperature and pressure conditions for aerospace applications. Our approach is grounded in introducing multiscale porosity, i.e., centimeter-scale channels embedded with micrometer-scale channels, into the ceramic heat exchanger to significantly improve its heat transfer performance and mechanical strength while maintaining minimal pressure losses. We first developed high-fidelity thermal-fluid-mechanical model capable of precisely capturing the heat transfer rate, temperature profile, pressure drop, and mechanical stress throughout the entire heat exchanger design. Guided by our model, we identified the optimal design parameters for the SiC heat exchanger body and manifolds. Then, we established a completed fabrication procedure to create multiscale features in the ceramic heat exchanger, including co-extrusion, lamination, burnout, and sintering. We fabricated multiple heat exchanger bodies consisting of 6 × 6 and 3 × 3 centimeter-scale channels where each individual centimeter-scale channel comprises 625 crack-free microchannels with 90 μm × 90 μm opening. Owing to the multiscale features, our fabricated heat exchanger bodies exhibited desirable mechanical strength with 156 MPa flexural strength under 1300 Celsius degree. Despite the demonstrated highly tailorable microscopic features and superior mechanical strength, we identified delamination due to the complex interaction among ceramic, polymer, and gas species can be a critical challenge to create fully defect-free heat exchanger, which requires further fundamental investigations in future works. To test the heat exchanger performance, we constructed a high-temperature and high-pressure experimental apparatus that can be safely operated under 400 Celsius degree and 4 bar. With insights gained from mechanistic modeling, material development, and detailed characterization, a cost model was finally developed to understand the market potential of the developed technology, where a cost of $43,000 Celsius degree/kW was envisioned. This project developed a transformative approach to high-performance heat exchanger design. The thermal-fluid-mechanical design approach developed in this project can serve as a generic tool to guide the design of various heat-exchangers operated under high-temperature and high-pressure conditions. The material fabrication approach established in this project can be a useful guide for ceramic processing at extreme length scales.

42 ENGINEERING↗
DOE OSTI2025

High-Temperature Gas-Cooled Reactors Multiphysics Simulation Demonstration and Code Validation

This study presents a comprehensive benchmarking and verification effort of several thermal-hydraulic and multiphysics capabilities for high-temperature gas-cooled reactor applications. The first part of this effort focuses on the running-in verification of Griffin’s multiphysics capabilities, specifically for simulating the evolution of pebble-bed reactor cores from startup to equilibrium. Since Fiscal Year 2024, improvements and enhancements have been implemented in Griffin, including simplifying the process to specify streamlines and developing the online cross-section generation capability. In the absence of validation data, code-to-code comparisons are conducted with kugelpy, showing good agreement for integral quantities like k-eff predictions and predictions for maximum power density. However, accuracy issues are noted for more detailed quantities like the spatial distribution of fission rate densities which will require further work to address. The second part of this report presents an improved System Analysis Module (SAM) core channel model where the effects of cross flow are considered during the pressurized loss of forced cooling transient, resulting in an improved agreement of the predicted pebble temperature with respect to the predictions from the SAM 2D porous media model. Additionally, the wall channeling effect due to variable porosity at the near wall region of the core is also investigated. Furthermore, to demonstrate Griffin’s online cross-section generation capability, a Multiphysics simulation is performed by coupling Griffin to the SAM core channel model. In the third part of the report, as a part of the Organisation for Economic Co-operation and Development/Nuclear Energy Agency (OECD/NEA) thermal-hydraulic code validation benchmark activity for a high-temperature gas-cooled reactor, the High Temperature Test Facility (HTTF) is investigated first using the NekRS computational fluid dynamics (CFD) code to study the flow mixing phenomenon in the lower plenum of the facility. Then, code-to-code and code-to-data comparisons are performed for Test PG27, which is a pressurized conduction cooldown (PCC) test, using five different codes by six organizations from five countries. The different simulations show good agreements in terms of the general trend but there are differences in some results such as the peak temperatures of different regions and heat removal rate.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Laser Powder Bed Fusion Additive Manufacture Nb1Zr Development

Next generation fission and fusion nuclear reactors require materials that can withstand operating temperatures greater than 500 °C, neutron irradiation doses of up to 200 displacements per atom (dpa), and potentially corrosive coolants such as the alkali liquid metals sodium, lithium, and NaK (Na33K eutectic alloy). Refractory alloys, such as Nb1Zr (Nb-1wt%Zr) and Molybdenum alloy TZM (Mo-0.5wt%Ti-0.08wt%Zr) have been traditionally considered viable candidates for advanced fission and fusion reactor concepts. However, it is relatively difficult to generate complex geometries of interest from these alloys using traditional manufacturing methods. In addition, there needs to be a concentrated effort to address refractory metal challenges at elevated temperature operation. In order to generate complex geometries of interest, modern manufacturing techniques are considered to increase the technological readiness level (TRL), cost-effectiveness, and schedule savings. This work focused on the continued development of laser powder bed fusion (L-PBF) additive manufacturing (AM) to improve both design flexibility, evaluate microstructure and properties, and ultimately accelerate the TRL and qualification of these processes and alloys for components to potentially be put into service. Niobium alloy Nb1Zr was identified through a down-selection process outlined in previous reports as a candidate to develop in L-PBF AM. Historically, Nb1Zr had been explored for high temperature fast spectrum fission reactors for both terrestrial and space applications. Molybdenum alloy TZM has also been considered for these reactor concepts due to exceptional high-temperature strength, creep resistance, and stability under irradiation. L-PBF AM of TZM has previously been investigated at LANL under the Microreactor program, NASA, ORNL, and in academia. However, due to the crack prone nature of TZM, L-PBF AM of TZM resulted in significant microcracking and additional development is required to pursue viable maturation. Other AM methods have been found to be more successful in printing TZM, and those alternatives approaches are discussed in this effort. The efforts detailed in this report focused on continued development of Nb1Zr through L-PBF and development of TZM via L-PBF and electron powder bed fusion (E-PBF). The objective of this work was to further the development of these AM techniques for the chosen refractory alloys, elucidating and addressing associated challenges through characterization of several demonstration builds. At LANL, Nb1Zr builds were completed using an EOS M290 and M400 machines, and a refractory alloy-dedicated L-PBF system, the Xact Metal XM200G, was installed. The XM200G primary purpose was to do the Nb1Zr parameter development process; however, due to difficulties associated with the machine installation and qualification process, it was decided to pivot development to the larger M400 and M290 machines. Although the supply of Nb1Zr powder was limited, it was sufficient to generate sub-scale metallographic specimens for the purpose of parameter development. This was first accomplished on the EOS M400 then the M290 due to machine schedule availability. Further development of TZM has been initiated at the University of Texas El Paso (UTEP) under contract with LANL to use both a heated build envelope L-PBF machine and E-PBF machine that have been found in the literature to mitigate microcracking. UTEP was provided with TZM powder and build plates to support parallel TZM parameter development across both machines. As part of the contract, UTEP will also be conducting microstructural characterization once optimized process parameters have been identified. The optimized process parameters for each machine will be used to generate a series of metallographic, mechanical, and surface finish specimens for subsequent characterization and testing. In the next section, we provide a detailed discussion of the methodology used for investigating the feasibility of leveraging these alloys for use in advanced reactor applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Covalent Triazine Framework-Derived Membranes: Engineered Sol–Gel Construction and Gas Separation Application

Covalent triazine frameworks (CTFs) represent one of the most extensively studied organic networks characterized by graphitic π-conjugated structures linked by aza-fused rings, possessing unique features such as compositions of light elements (e.g., C, H, and N), porous architectures abundant heteroatom involvement, and extensively conjugated structures. In addition, the textural and chemical structures of CTFs could be engineered via synthesis control to accommodate diverse applications. CTF materials with notable characteristics, including plentiful (ultra-)micropores, high surface areas, and the presence of CO 2 -philic functional groups involving nitrogen (N), oxygen (O), and fluorine (F), hold great promise as potential candidates for anthropogenic CO 2 capture and sequestration (CCS) applications. However, the conventional high-temperature involved ionothermal procedures and the solution-based coupling pathway only afforded CTF materials in powder form, which is difficult to be processed toward membrane formation. Successful fabrication of CTF-derived membranes will rely on the development of alternative polymerization approaches as well as structural engineering to afford membrane architectures with controllable porosity distribution and active interaction sites with CO 2 benefiting the CO 2 separation procedure. In this Account, a demonstration of the latest progress in the development of CTF-derived membranes was provided. The CTF membranes were mainly synthesized via a superacid (e.g., CF 3 SO 3 H)-promoted sol–gel approach involving the polymerization of aromatic nitrile monomers. The formation of the triazine unit through the trimerization of cyano groups served as the cross-linkers, resulting in the creation of π-conjugated networks alongside the arenes present in the starting materials. The aromatic nitrile monomers with rigid and sterically hindered structures were required to afford CTF membranes with nanoporous architectures. The acidity of the superacid and reactivity of the aromatic monomers played critical roles in the polymerization efficiency. The monomer diversity and synthesis tunability endowed the introduction of CO 2 -philic functionalities (e.g., pyrazole and fluorine) within the CTF skeletons, and integration of ionic moieties was achieved by adopting FSO 3 H with stronger acidity as the catalyst and aromatic nitrile monomers with pyrazine structures. To ensure the successful construction of fluorinated CTF membranes, it is important to avoid any fluorines on the ortho-position of the cyano groups on the benzene ring. Through control over the monomers and reaction conditions, flexible, transparent, and insoluble CTF membranes could be fabricated. The sol–gel method could be further expanded to membrane fabrication through acetyl-to-benzene transformation through synthesis control. The mild oxidation-exfoliation-filtration method was also demonstrated to fabricate substrate-supported CTF membranes. The as-afforded membranes are well characterized to determine the structural features and provide information to study the structure-performance relationship. Here, the application of CTF membranes in CO 2 separation was summarized, focusing on the approaches being developed to enhance CO 2 uptake and separation performance. In addition to utilizing the pristine CTF membranes for gas separation, functionalized carbon molecular sieve membranes could be obtained from the pyrolysis of thermally stable CTF membrane precursors toward efficient CO 2 separation, benefiting from the abundant ultramicropores being created during the pyrolysis/decomposition procedure and involvement of CO 2 -philic functionalities such as fluorine and nitrogen-containing moieties. Based on these achievements, unsolved issues in CTF membrane-related fabrication and applications, including the potential solution approaches, have been proposed to advance the application of CTF membranes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Effect of aging on failure mechanism of Alloy 709 at various temperatures

Alloy 709 is a novel austenitic stainless steel with high temperature creep strength, weldability, and corrosion resistance. These properties make the material suitable for applications in the structure of next-generation nuclear power plants. Enduring high temperatures for an extended period of time in the harsh environments of a nuclear power plant results in thermal aging of the material. Therefore, it is imperative to study the effect of thermal aging on the microstructure and mechanical properties of Alloy 709 before its application in the next generation power plants. In this study, hot-processed (forged + rolled), annealed and quenched ingots of Alloy 709 are aged at 650 °C for 2000 h in air and then tested at various temperatures up to 850 °C in an in-situ heating-loading Scanning Electron Microscope (SEM) equipped with Energy Dispersive Spectroscopy (EDS) and Electron Backscatter Diffraction (EBSD). The effect of testing temperature and aging on microstructural evolutions during tensile testing of as-received and aged samples are studied. Furthermore, both as-received and aged samples displayed serrations and drop in ductility at elevated temperatures, due to the effect of dynamic strain aging (DSA). The occurrence of DSA activity was found within temperatures range of 500 °C–750 °C in as-received and 550 °C - 650 °C in aged samples. The aged samples showed less elongation accompanied by shallower dimples on the fractured surface, indicating less ductile failure mechanism compared to as-received samples. Failure mechanism observations on the fracture surface using SEM fractography are correlated to the observations made on the sample surface using in-situ SEM to achieve a complementary set of information to better understand the failure mechanism of this novel alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Mesoscale Magnetostructural Phase Separation in Fe‐deficient Fe 5 GeTe 2

Two-dimensional van der Waals ferromagnet Fe 5-x GeTe 2 (F5GT) is promising for spintronic applications due to its high Curie temperature, layered structure, and ability to host complex magnetic textures. However, the origin of its sample-dependent magnetic anisotropy remains unclear, hindering control of its magnetic behavior. Here, we use spatially resolved cryogenic scanning transmission electron microscopy (STEM) to correlatively map magnetism, lattice structure, and chemistry across atomic-to-micron scales. We reveal that only mesoscale, not nanoscale, inclusions of a Fe-deficient secondary phase significantly modify magnetic behavior, establishing a previously unrecognized critical length scale. This phase separation, induced by quenching, leads to in-plane magnetic anisotropy, while slow cooling confines separation to a few nanometers and preserves out-of-plane anisotropy. These findings reconcile prior inconsistencies and establish a predictive framework for tuning magnetism in F5GT through thermal processing, with broader implications for controlling anisotropy in other two-dimensional magnetic materials.

2D ferromagnets↗
DOE OSTI2023

Low-temperature oxidation pathways are critical to thermal incineration of PFAS-laden materials

With growing desire to destroy per- and poly-fluoroalkyl substances (PFAS) now known to be detrimental to human health, a sound understanding of fluorocarbon combustion chemistry is important to efficient thermal destruction within incinerators. While most fluorocarbon combustion models and the sets of reactions contained within them were originally developed for the high temperatures encountered in flame suppression applications, they have often been used to assess PFAS destruction in incinerators, which emphasize a lower range of temperatures. We present results that demonstrate that low-temperature fluorocarbon oxidation pathways—not yet known to play a role in fluorocarbon combustion—impact key incinerator performance metrics, including: PFAS surrogate mole fractions, products of incomplete destruction, and waste destruction efficiencies. The results further point to the utility of NO as a potential additive. The present results show the influence of these pathways for CF 3 O 2 , for which some data are available, but analogous pathways would also occur for other fluoroalkylperoxy radicals, for which little is known. Furthermore, the results demonstrate the need for future work to identify and characterize low-temperature pathways more generally, consider such pathways in kinetic model development, and experimentally probe intermediate temperature conditions to better understand, design, and control thermal destruction technologies for improved PFAS management.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Creating free standing covalent organic framework membranes by nanocrystal suturing in sol gel solutions

The sol-gel synthesis represents a versatile platform to fabricate ceramic inorganic membranes. However, it is still a grand challenge to push the boundary of sol-gel chemistry towards high-quality organic membrane construction. Herein, a facile and controlled nanocrystal suturing strategy in sol-gel solutions is developed to afford highly crystalline and free-standing covalent organic framework membranes. The key chemistry design lies in deploying tiny threads (1 mol% dual-NH 2 -tail linear polymer) to efficiently suture the highly charged covalent organic framework nanocrystals stabilized and confined in sol-gel solutions, creating a continuous and intact membrane surface. A subsequent treatment heals the sutured covalent organic framework nanocrystals, yielding a free-standing membrane with high crystallinity and ordered pores. The structure evolution and role of the thread linker are elucidated via operando spectroscopy and microscopy. The as-afforded covalent organic framework membranes demonstrate attractive proton transport performance in high temperature and anhydrous fuel cell applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Thermally induced PtOx interfacial layer enhances stability of Pt/β-Ga2O3 vertical Schottky diodes

This study investigates the long-term stability of Pt/β-Ga2O3 field-plated Schottky barrier diodes at high temperatures, with extended thermal cycling and soaking stress. The device characteristics reveal a strong dependence on operating temperature, leading to an ON/OFF current ratio of ∼10× at ±3 V and 600 °C. Extensive thermal cycling (25 cycles over 100 h) between room temperature and 350 °C shows that leakage currents stabilize after the initial ten cycles. This stabilization is likely due to the formation of a thin PtOx layer at the Pt/β-Ga2O3 interface, as confirmed by high-resolution scanning transmission electron microscopy. Further exposure to a constant 350 °C environment for 10 h reveals a slight increase in the leakage current from 10−7 to 10−6 A at −5 V and degradation of the forward current, due to potential thermodynamic instability of the Ohmic contacts. This study provides insights into the changes in the Pt/β-Ga2O3 diode performance with thermal stress, offering a basis for predicting the device’s operational reliability at high temperatures for sensing and power applications.

08 HYDROGEN↗