Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Effect of Tempering and Rolling on Fatigue Crack Growth Behavior of Modified 9Cr-1Mo Steel

In the present work, fatigue crack growth (FCG) behavior of modified 9Cr-1Mo steel has been investigated near fatigue threshold and Paris regime at room temperature (RT) and 650 °C. The modified 9Cr-1Mo steel was subjected to normalizing at 1050 °C followed by tempering (650-750 °C) and warm rolling at 550 °C followed by tempering in order to improve its precipitation state and refine microstructure. The microstructural parameters such as grain size, block size, lath width and precipitate size were examined and correlated with FCG and tensile properties of investigated samples. The results showed that decreasing tempering temperature significantly reduces the fatigue threshold at RT while increases the yield strength at elevated temperature (i.e., 650 °C). Increase in fatigue threshold is found to increase with the increase in block size, whereas high density of fine precipitates contributed the high temperature strength. The FCG rate in Paris regime was less affected by heat treatment and rolling process at RT. However, rolled sample tested at 650 °C shows a decrease in FCG rate as compared to heat-treated samples. In terms of higher FCG resistance and yield strength, warm rolling followed by tempering at low temperature (i.e., 700 °C) can be considered optimum. For the numerical simulation of FCG behavior, extended finite element method (XFEM) along with Paris law has been implemented in ABAQUS using python script. The simulated FCG behavior is found in good agreement with the experimental results.

36 MATERIALS SCIENCE↗

Characterization of hot-pressed von Alpen type NASICON ceramic electrolytes

The Na-ion conducting solid electrolyte NASICON is a promising solid state electrolyte (SSE) for use in Na based electrochemical systems. The effects of particle morphology and synthesis of von Alpen type NASICON via hot-pressing were investigated. Spray dried particles were shown to improve mechanical and electrochemical properties. X-ray diffraction, scanning electron microscopy, impulse excitation measurements, Vickers hardness, and impedance spectroscopy were used to correlate relationships between phase purity, microstructure, mechanical properties, and electrochemical properties. Scanning electron microscopy showed the presence of a glass phase as between 19.08% and 28.23% area percentage and a ZrO 2 phase between 0.46% and 3.51% area percentage in the hot-pressed samples. Impulse excitation showed elastic modulus varying from 83.65 to 97.65 GPa. The first values of Poisson's ratio and shear modulus of NASICON are reported as between 0.23 and 0.26 and 33.87 to 38.79 GPa, respectively. Vickers hardness and fracture toughness measurements showed Vickers hardness ranging from 4.30 to 4.68 GPa and fracture toughness ranging from 1.05 to 1.09 MPa m ½ . Impedance spectroscopy showed grain conductivities ranging from 1.023 to 1.287 mS/cm, with grain boundary resistance percentages between 73.22 and 47.5%. Total conductivities ranged from 0.292 to 0.596 mS/cm, with 0.596 mS/cm being achieved at room temperature for the spray dried powders with lower grain boundary resistance percentages.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Low temperature fabrication of perovskite solar cells with TiO{sub 2} nanoparticle layers

TiO{sub 2}/CH{sub 3}NH{sub 3}PbI{sub 3}-based photovoltaic devices were fabricated by a spin-coating method using a mixture solution. TiO{sub 2} require high-temperature processing to achieve suitably high carrier mobility. TiO{sub 2} electron transport layers and TiO{sub 2} scaffold layers for the perovskite were fabricated from TiO{sub 2} nanoparticles with different grain sizes. The photovoltaic properties and microstructures of solar cells were characterized. Nanoparticle sizes of these TiO{sub 2} were 23 nm and 3 nm and the performance of solar cells was improved by combination of two TiO{sub 2} nanoparticles.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Crystallization of the glassy grain boundary phase in silicon nitride ceramics

The role was studied of the intergranular glassy phase in silicon nitride as-processed with yttria as a sintering aid. The microstructure, crystallization, and viscosity of the glassy phase were areas studied. Crystallization of the intergranular glassy phase to more refractory crystalline phases should improve the high temperature mechanical properties of the silicon nitride. The addition of a nucleating agent will increase the rate of crystallization. The measurement of the viscosity of the glassy phase will permit the estimation of the high temperature deformation of the silicon nitride.

Drummond, Charles H., III↗

Superconducting Thin Films for The Enhancement of Superconducting Radio Frequency Accelerator Cavities

Bulk niobium (Nb) superconducting radio frequency (SRF) cavities are currently the preferred method for acceleration of charged particles at accelerating facilities around the world. However, bulk Nb cavities have poor thermal conductance, impose material and design restrictions on other components of a particle accelerator, have low reproducibility and are approaching the fundamental material-dependent accelerating field limit of approximately 50MV/m. Since the SRF phenomena occurs at surfaces within a shallow depth of ~1 μm, a proposed solution to this problem has been to utilize thin film technology to deposit superconducting thin films on the interior of cavities to engineer the active SRF surface in order to achieve cavities with enhanced properties and performance. Two proposed thin film applications for SRF cavities are: 1) Nb thin films coated on bulk cavities made of suitable castable metals (such as copper or aluminum) and 2) multilayer films designed to increase the accelerating gradient and performance of SRF cavities. While Nb thin films on copper (Cu) cavities have been attempted in the past using DC magnetron sputtering (DCMS), such cavities have never performed at the bulk Nb level. However, new energetic condensation techniques for film deposition, such as High Power Impulse Magnetron Sputtering (HiPIMS), offer the opportunity to create suitably thick Nb films with improved density, microstructure and adhesion compared to traditional DCMS. Clearly use of such novel technique requires fundamental studies to assess surface evolution and growth modes during deposition and resulting microstructure and surface morphology and the correlation with RF superconducting properties. Here we present detailed structure-property correlative research studies done on Nb/Cu thin films and NbN- and NbTiN-based multilayers made using HiPIMS and DCMS, respectively. Experiment Numbers:

Burton, Matthew↗

Viewing is understanding: Graphite microstructure effects on infiltrated molten salt distribution revealed by 3D neutron tomography

Molten salt infiltration in the pore network of nuclear graphite may cause unwanted changes to graphite's local structure and mechanical and thermal properties. A detailed and comprehensive understanding of molten salt intrusion (distribution across sample cross section and penetration depth) is needed to assess its effects. Here, in this work, we report on an improved methodology for the use of neutron imaging (computed tomography) to evaluate salt penetration and distribution of a wide range of graphite grades with diverse microstructures. Neutron tomography data were acquired on the same graphite sample before and after salt intrusion; the 3D reconstructed volumes were digitally co-registered and subtracted. The difference in neutron attenuation coefficient represents direct visualization of FLiNaK (LiF–NaF–KF) salt distribution in the salt-impregnated graphite samples. This improved methodology was applied to investigate the effect of exposure times (12 h and 336 h) and of graphite microstructure when exposed to FLiNaK at 750 °C and 3 bar (gauge) pressure, starting from flowing argon at near atmospheric pressure. The results show that medium-grained and fine-grained graphites evolve to equilibrium at significantly different rates: fast salt uptake in medium-grained graphites produces salt deposits throughout the volume of graphite specimens, whereas salt infiltration in fine-grained graphites is much slower and limited to exposed surfaces.

FLiNaK infiltration↗

Microstructure and properties of additively manufactured Al–Ce–Mg alloys

Additive manufacturing of aluminum alloys is largely dominated by a near-eutectic Al-Si compositions, which are highly weldable, but have mechanical properties that are not competitive with conventional wrought Al alloys. In addition, there is a need for new Al alloys with improved high temperature properties and thermal stability for applications in the automotive and aerospace fields. In this work, we considered laser powder bed fusion additive manufacturing of two alloys in the Al–Ce–Mg system, designed as near-eutectic (Al–11Ce–7Mg) and hyper-eutectic (Al–15Ce–9Mg) compositions with respect to the binary L → Al + Al 11 Ce eutectic reaction. The addition of magnesium is used to promote solid solution strengthening. A custom laser scan pattern was used to reduce the formation of keyhole porosity, which was caused by excessive vaporization due to the high vapor pressure of magnesium. The microstructure and tensile mechanical properties of the alloys were characterized in the as-fabricated condition and following hot isostatic pressing. The two alloys exhibit significant variations in solidification structure morphology. These variations in non-equilibrium solidification structure were rationalized using a combination of thermodynamic and thermal modeling. Both alloys showed higher yield strength than AM Al-10Si-Mg for temperatures up to 350 °C and better strength retention at elevated temperatures than additively manufactured Scalmaloy.

36 MATERIALS SCIENCE↗

Effects of 3d electron configurations on helium bubble formation and void swelling in concentrated solid-solution alloys

Currently, elemental specific chemical complexity is known to play a vital role in microstructure development in single-phase concentrated solid-solution alloys (SP-CSAs), including both He bubble formation and irradiation-induced void swelling. While cavity formation and evolution under ion irradiation at elevated temperature are complex nonequilibrium processes, chemical effects are revealed at the level of electrons and atoms herein in a simplified picture, using Ni and a special set of Ni-based SP-CSAs composed of 3d transition metals as model alloys. Based on Ni and the model alloys with minimized variables (e.g., atomic mass, size, and lattice structure), we report on the effects of chemically-biased energy dissipation, defect energetics, sluggish diffusion, and atomic transport on cavity formation and evolution under both self-ion Ni irradiation and He implantation. The observed difference in microstructure evolution is attributed to the effects of d electron interactions in their integrated ability to dissipate radiation energy. The exhibited impact of alloying 3d transition metals with larger differences in the outermost electron counts suggests a simple design strategy for tuning defect properties to improve radiation tolerance in structural alloys.

36 MATERIALS SCIENCE↗

Effect of cerium on structure modifications of a hybrid sol–gel coating, its mechanical properties and anti-corrosion behavior

Highlights: ► New sol–gel routes to replace chromates for corrosion protection of aluminum. ► Effect of cerium concentration on the microstructure of xerogel. ► Electrochemical and mechanical performances of hybrid coating with different cerium contents. ► Good correlation between the different results with an optimal cerium content of 0.01 M. -- Abstract: An organic–inorganic hybrid coating was developed to improve the corrosion resistance of the aluminum alloy AA 2024-T3. Organic and inorganic coatings derived from glycidoxypropyl-trimethoxysilane (GPTMS) and aluminum tri-sec-butoxide Al(O{sup s}Bu){sub 3}, with different cerium contents, were deposited onto aluminum by dip-coating process. Corrosion resistance and mechanical properties were investigated by electrochemical impedance measurements and nano-indentation respectively. An optimal cerium concentration of 0.01 M was evidenced. To correlate and explain the hybrid coating performances in relation to the cerium content, NMR experiments were performed. It has been shown that when the cerium concentration in the hybrid is higher than 0.01 M there are important modifications in the hybrid structure that account for the mechanical properties and anti-corrosion behavior of the sol–gel coating.

36 MATERIALS SCIENCE↗

Effect of hydromagnesite addition on the properties and water resistance of magnesium oxysulfate (MOS) cement

Magnesium oxysulfate (MOS) cement exhibits excessive cracking when exposed to water because of the reaction of residual MgO that forms extensive Mg(OH){sub 2}, which significantly limits the application breadth of MOS cement. This study investigates the effects of the addition of hydromagnesite ((MgCO{sub 3}){sub 4}·Mg(OH){sub 2}·4H{sub 2}O) on the hydration products of MOS cement and the microstructure and physical properties of MOS paste samples. It was found that the addition of hydromagnesite increased the compressive strength and water resistance of MOS cement. This effect is mainly due to the reaction between hydromagnesite and free MgO present in the cement that forms magnesium carbonate (MgCO{sub 3}·Mg(OH){sub 2}·3H{sub 2}O) and acts as an additional binding phase. The use of hydromagnesite as an additive for improving the water resistance of MOS cement leads to a decrease in the residual MgO content and improves the water stability of amorphous materials.

36 MATERIALS SCIENCE↗

Oxynitrided Surface Layer Produced On Ti6Al4V Titanium Alloy Under Low Temperature Glow Discharge Conditions For Medical Applications

In spite that titanium oxides increase biocompatibility of titanium implants but their functional life is limited due to the problems arising from brittles and metalosis. Therefore technology, that allow to produce composite surface layer with controlled microstructure, chemical and phase composition and surface morphology on titanium alloy and eliminates the oxides disadvantages has been existing till now is searched. The requirements of titanium and its alloys implants can be fulfill by the low-temperature glow discharge assisted oxynitriding.The paper describes the surface layer of TiO{sub 2}+TiN+Ti{sub 2}N+{alpha}Ti(N) type produced at temperature 680 deg. C that preserves mechanical properties of titanium alloy Ti6Al4V. Characteristics of produced diffusion multi-phase surface layers in range of phase composition, microstructure (SEM, TEM, XRD) and its properties, such as frictional wear resistance are presented. The biological properties in dependency to the applied sterilization method are also analyzed.Properties of produced surface layers are discussed with reference to titanium alloy. The obtained data show that produced surface layers improves titanium alloy properties both frictional wear and biological. Preliminary in vitro examinations show good biocompatibility and antithrombogenic properties.

36 MATERIALS SCIENCE↗

Large Destabilization of (TiVNb)-Based Hydrides via (Al, Mo) Addition: Insights from Experiments and Data-Driven Models

High-entropy alloys (HEAs) represent an interesting alloying strategy that can yield exceptional performance properties needed across a variety of technology applications, including hydrogen storage. Examples include ultrahigh volumetric capacity materials (BCC alloys → FCC dihydrides) with improved thermodynamics relative to conventional high-capacity metal hydrides (like MgH 2 ), but still further destabilization is needed to reduce operating temperature and increase system-level capacity. Here, in this work, we demonstrate efficient hydride destabilization strategies by synthesizing two new Al 0.05 (TiVNb) 0.95–x Mo x (x = 0.05, 0.10) compositions. We specifically evaluate the effect of molybdenum (Mo) addition on the phase structure, microstructure, hydrogen absorption, and desorption properties. Both alloys crystallize in a bcc structure with decreasing lattice parameters as the Mo content increases. The alloys can rapidly absorb hydrogen at 25 °C with capacities of 1.78 H/M (2.79 wt %) and 1.79 H/M (2.75 wt %) with increasing Mo content. Pressure-composition isotherms suggest a two-step reaction for hydrogen absorption to a final fcc dihydride phase. The experiments demonstrate that increasing Mo content results in a significant hydride destabilization, which is consistent with predictions from a gradient boosting tree data-driven model for metal hydride thermodynamics. Furthermore, improved desorption properties with increasing Mo content and reversibility were observed by in situ synchrotron X-ray diffraction, in situ neutron diffraction, and thermal desorption spectroscopy.

36 MATERIALS SCIENCE↗

Modeling Single-Crystal Battery Materials: From Fundamental Understanding to Performance Evaluation

The performance of rechargeable batteries is fundamentally influenced by the physicochemical properties and microstructural features of their key material components. Recent experimental advancements have highlighted the potential of single-crystal (SC) morphologies to address inherent limitations of polycrystalline (PC) electrodes and solid-state electrolytes, offering tunable charge transport kinetics and improved cell cycling performance. Here, this review examines how state-of-the-art computational modeling, from atomistic and mesoscale to continuum-level approaches, including machine learning methodologies, has been utilized to investigate the critical factors governing the electrochemical behavior of SC battery materials. We explore how predictive modeling can elucidate the processing–structure–property–performance relationships of SC cathodes, anodes, and solid-state electrolytes, with a focus on unique SC characteristics such as crystallographic anisotropy, size effects, and facet-dependent properties. Additionally, we identify limitations in commonly used modeling techniques and discuss strategies to address these challenges. By integrating high-fidelity simulations with experimental insights, this review aims to outline a clear path for the rational design and optimization of SC battery components, paving the way for accelerated advancements in energy storage technologies.

Materials science↗

Comparative study of structure formation and mechanical behavior of age-hardened Ti–Nb–Zr and Ti–Nb–Ta shape memory alloys

This work sets out to study the peculiar effects of aging treatment on the structure and mechanical behavior of cold-rolled and annealed biomedical Ti–21.8Nb–6.0Zr (TNZ) and Ti–19.7Nb–5.8Ta (TNT) (at.%) shape memory alloys by means of transmission electron microscopy, X-ray diffractometry, functional fatigue and thermomechanical testing techniques. Dissimilar effects of aging treatment on the mechanical behavior of Zr- and Ta-doped alloys are explained by the differences in the ω-phase formation rate, precipitate size, fraction and distribution, and by their effect on the alloys' critical stresses and transformation temperatures. Even short-time aging of the TNZ alloy leads to its drastic embrittlement caused by “overaging”. On the contrary, during aging of the TNT alloy, formation of finely dispersed ω-phase precipitates is gradual and controllable, which makes it possible to finely adjust the TNT alloy functional properties using precipitation hardening mechanisms. To create in this alloy nanosubgrained dislocation substructure containing highly-dispersed coherent nanosized ω-phase precipitates, the following optimum thermomechanical treatment is recommended: cold rolling (true strain 0.37), followed by post-deformation annealing (600 °C, 15–30 min) and age-hardening (300 °C, 30 min) thermal treatments. It is shown that in TNT alloy, pre-transition diffraction effects (diffuse reflections) can “mask” the β-phase substructure and morphology of secondary phases. - Highlights: • TNZ alloy is characterized by much higher ω-phase precipitation rate than TNT alloy. • Difference in precipitation rates is linked to the difference in Zr and Ta diffusion mobility. • Aging of nanosubgrained TNZ alloy worsens its properties irrespective of the aging time. • Aging time of nanosubgrained TNT alloy can be optimized to improve its properties.

36 MATERIALS SCIENCE↗

Effect of formation temperature on properties of graphite/stannum composite for bipolar plate

Bipolar plates are key components in Proton Exchange Membrane (PEM) fuel cells. They carry current away from the cell and withstand the clamping force of the stack assembly. Therefore, PEM fuel cell bipolar plates must have high electrical conductivity and adequate mechanical strength, in addition to being light weight and low cost in terms of both applicable materials and production methods. In this research, the raw materials used to fabricate the high performance bipolar plate are Graphite (Gr), Stannum (Sn) and Polypropylene (PP). All materials used was in powder form and Gr and Sn act as fillers and the PP acts as binder. The ratio of fillers (Gr/Sn) and binder (PP) was fixed at 80:20. For the multi-conductive filler, small amount of Sn, which is 10 up to 20wt% (from the total weight of fillers 80%) have been added into Gr/Sn/PP composite. The fillers were mixed by using the ball mill machine. The second stage of mixing process between the mixer of fillers and binder is also carried out by using ball mill machine before the compaction process by the hot press machine. The effect of formation temperatures (160°C-170°C) on the properties of Gr/Sn/PP composite had been studied in detail, especially the electrical conductivity, bulk density, hardness and microstructure analysis of Gr/Sn/PP composite. The result shows that there are significant improvement in the electrical conductivity and bulk density, which are exceeding the US-DoE target with the maximum value of 265.35 S/cm and 1.682g/cm{sup 3} respectively.

36 MATERIALS SCIENCE↗

Mechanical properties of weldments in experimental Fe-12Mn-0.2Ti and Fe-12Mn-1Mo-0.2Ti alloys for cryogenic service

Mechanical properties of weldments in two Fe-12Mn experimental alloys designed for cryogenic service were evaluated. Weldments were made using the GTA welding process. Tests to evaluate the weldments were conducted at -196 C and included: equivalent energy fracture toughness tests; autogenous transverse weld, notched transverse weld, and longitudinal weld tensile tests; and all-weld-metal tensile tests. The Fe-12Mn-0.2Ti and Fe-12Mn-1Mo-0.2Ti alloys proved weldable for cryogenic service, with weld metal and heat-affected zone properties comparable with those of the base metal. Optimum properties were achieved in the base alloys, weld metals, and heat-affected zones after a two-step heat treatment consisting of austenitizing at 900 C followed by tempering at 500 C. The Mo-containing alloy offered a marked improvement in cryogenic properties over those of the Mo-free alloy. Molybdenum increased the amount of retained austenite and reduced the amount of epsilon martensite observed in the microstructure of the two alloys.

Stephens, J. R.↗

Microstructure and magnetization of doped Y-Ba-Ca-O materials prepared by melt quench and post annealing method

Y-Ba-Cu-O bulk materials prepared using the melt quench and post annealing method were shown to have very high maximum as well as remanent magnetization. Studies were carried out on materials prepared using this method which deviate from the Y:Ba:Cu = 1:2:3 stoichiometry. In one series of materials, only the stoichiometry was changed, in particular by introducing an excess of yttrium. In other cases, dopants including several rare earths were introduced. Effects of variations in composition on microstructure and phase evolution are discussed, as well as effects on the magnetic susceptibility and on the magnetization. The results show that doped materials can exhibit improvements in magnetic properties. Furthermore, the use of dopants sheds light on the role of defect sites in flux pinning.

Hojaji, H.↗

Automated Probabilistic Finite Element Model Calibration Tool Based on Uncertainty Quantification and Machine Learning

Qualification and certification of safety critical parts is a hurdle to the adoption of metallic additively manufactured components for aerospace vehicle applications. Challenges include variability in part properties due to inconsistent defect distribution and microstructure. Understanding of the process through finite element modeling (FEM), and process control through in-situ monitoring, may result in significant improvements; however, solutions useful to manufacturers will require large volumes of data and automated data utilization. Toward this end, a generalizable automated FEM calibration paradigm is developed. This paradigm leverages existing and novel tools from machine learning and uncertainty quantification to enable the automatic calibration of FEMs without requiring prior knowledge of the model performance across input parameter space, including meshing and solver settings, which can require time consuming manual model probing or cause noisy and inconsistent predictions. The result is a probabilistic distribution of calibrated and validated FEM input parameters targeting measured data.

Additive manufacturing model calibration finite el↗