Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Report on Sodium Compatibility of Advanced Structural Materials

This report provides an update on the evaluation of sodium structural materials. The report is a deliverable (level 3) in FY11 (M3A11AN04030403), under the Work Package A-11AN040304, “Sodium Compatibility of Advanced Structural Materials” performed by Argonne National Laboratory (ANL), as part of Advanced Structural Materials Program for the Advanced Reactor Concepts. This work package supports the advanced structural materials development by providing corrosion and tensile data from the standpoint of sodium compatibility of advanced structural alloys. The scope of work involves exposure of advanced structural alloys such as G92, mod.9Cr-1Mo (G91) ferritic-martensitic steels and HT-UPS austenitic stainless steels to a flowing sodium environment with controlled impurity concentrations. The exposed specimens are analyzed for their corrosion performance, microstructural changes, and tensile behavior. Previous reports examined the thermodynamic and kinetic factors involved in the design, fabrication, and construction of a forced convection sodium loop for sodium compatibility studies of advanced materials. This report presents the results on corrosion performance, microstructure, and tensile properties of advanced ferritic-martensitic and austenitic alloys exposed to liquid sodium at 550°C for up to 2700 h and at 650°C for up to 5064 h in the forced convection sodium loop. The oxygen content of sodium was controlled by the cold-trapping method to achieve ~1 wppm oxygen level. Four alloys were examined, G92 in the normalized and tempered condition (H1 G92), G92 in the cold-rolled condition (H2 G92), G91 in the normalized and tempered condition, and hot-rolled HT-UPS. G91 was included as a reference to compare with advanced alloy, G92. It was found that all four alloys showed weight loss after sodium exposures at 550 and 650°C. The weight loss of the four alloys was comparable after sodium exposures at 550°C; the weight loss of ferritic-martensitic steels, G92 and G91 is more significant than that of austenitic stainless steel, HT-UPS after sodium exposures at 650°C. Sodium exposures up to 2700 h at 550°C had no significant influence on tensile properties, while sodium exposures up to 5064 h at 650°C dramatically lowered the tensile strengths of the four alloys. The ultimate tensile strength of H1 G92, H2 G92, and G91 ferritic-martensitic steels was reduced to as much as nearly half of its initial value after sodium exposures at 650°C. Though the uniform elongation was recovered to some extent, these three ferritic-martensitic steels showed considerable strain softening after sodium exposures. The yield stress of HT-UPS austenitic stainless steel increased, the ultimate tensile strength decreased, and the total elongation was reduced after sodium exposures at 650°C. The dynamic strain aging effect observed in the as-received HT-UPS specimens became less pronounced after sodium exposures at 650°C. Microstructural characterization of sodium-exposed specimens showed no appreciable surface deterioration or grain structure changes under an optical microscope, except for the H2 G92 steel, in which the martensite structure transformed to large grain ferrite after sodium exposures at 650°C. TEM observations of the sodium-exposed H2 G92 steel showed significant recrystallization after sodium exposure for 2700 h at 550°C, and transformation of martensite to ferrite and high density of precipitates in nearly dislocation-free matrix after sodium exposures at 650°C. Further microstructural analysis and evaluation of decarburization/carburization behavior is needed to understand the dramatic changes in the tensile strengths of advanced ferritic-martensitic and austenitic steels after sodium exposures at 650°C.

36 MATERIALS SCIENCE↗

Invertible Temper Modeling using Normalizing Flows and the Effects of Structure Preserving Loss

Advanced manufacturing research and development is typically small-scale, owing to costly experiments associated with these novel processes. Deep learning techniques could help accelerate this development cycle but frequently struggle in small-data regimes like the advanced manufacturing space. While prior work has applied deep learning to modeling visually plausible advanced manufacturing microstructures, little work has been done on data-driven modeling of how microstructures are affected by heat treatment, or assessing the degree to which synthetic microstructures are able to support existing workflows. We propose to address this gap by using invertible neural networks (normalizing flows) to model the effects of heat treatment, e.g., tempering. The model is developed using scanning electron microscope imagery from samples produced using shear-assisted processing and extrusion (ShAPE) manufacturing. This approach not only produces visually and topologically plausible samples, but also captures information related to a sample’s material properties or experimental process parameters. We also demonstrate that topological data analysis, used in prior work to characterize microstructures, can also be used to stabilize model training, preserve structure, and improve downstream results. We assess directions for future work and identify our approach as an important step towards end-to-end deep learning system for accelerating advanced manufacturing research and development.

Howland, Sylvia↗

Nucleation and growth characteristics of graphite spheroids in bainite during graphitization annealing of a medium carbon steel

The evolution of microstructure in bainite during graphitization annealing at 680 °C of Jominy-quenched bars of an Al-Si bearing medium carbon (0.4C wt%) steel has been studied and compared with that in martensite by using light, scanning and transmission electron microscopy. The results show that the graphitization process in bainite is different from that in martensite in many aspects such as the initial carbon state, the behavior of cementite, the nucleation-growth feature and kinetics of formation of graphite spheroids during graphitization annealing, and the shape, size and distribution of these graphite spheroids. The fact that the graphitization in bainite can produce more homogeneous graphite spheroids with more spherical shape and finer size in a shorter annealing time without the help of preexisting coring particles implies that bainite should be a better starting structure than martensite for making graphitic steel. - Highlights: • This article presents a microstructural characterization of formation of graphite spheroids in bainite. • Nucleation and growth characteristics of graphite spheroids formed in bainite and martensite are compared. • Bainite should be a better starting structure for making graphitic steel as results show.

36 MATERIALS SCIENCE↗

Solution heat-treatment of Nb-modified MAR-M247 superalloy

MAR-M247 superalloy has excellent mechanical properties and good oxidation resistance at elevated temperatures. Niobium is an element known as {gamma} Prime phase hardener in nickel-based superalloys, besides promoting homogeneous distribution of MC carbides. This work is inserted in a project that aims to evaluate the total replacement of tantalum by niobium atoms in MAR-M247 superalloy (10.2 Co, 10.2 W, 8.5Cr, 5.6 Al, 1.6 Nb, 1.4 Hf, 1.1 Ti, 0.7 Mo, 0.15 C, 0.06 Zr, 0.015 B, Ni balance-wt.%). Based on microstructural characterizations (SEM and FEG-SEM, both with EDS) of the as-cast material and heat-treated materials as well as utilizing Thermocalc simulations and experiments of differential thermal analysis (DTA), heat-treatment at 1260 Degree-Sign C for 8 h was chosen as an ideal condition for the solution of Nb-modified MAR-M247 superalloy. The hardness of as-cast and ideally solution treated materials was 390 {+-} 14 HV and 415 {+-} 6 HV, respectively. - Highlights: Black-Right-Pointing-Pointer DTA and microstructure of MAR-M247(Nb) showed a good agreement with Thermocalc. Black-Right-Pointing-Pointer An ideal condition for solution heat-treatment of MAR-M247(Nb) is 1260 Degree-Sign C for 8 h. Black-Right-Pointing-Pointer It was an observed evidence of incipient melting in samples heat-treated at 1280 Degree-Sign C.

36 MATERIALS SCIENCE↗

Variation in supercurrent connectivity and vortex pinning of state-of-the-art pulsed laser deposited RE Ba 2 Cu 3 O 7- x coated conductors

REBa 2 Cu 3 O 7-x (REBCO, RE: rare earth) coated conductors (CCs) suffer from great critical current I c differences between different manufacturers, I c variations within individual manufacturers, and often significant lengthwise fluctuations. The understanding of such variations is complicated by the lack of a direct correlation between I c and the critical current density J c . In fact, although J c is the fundamental property determined by the local vortex pinning landscape, I c is often limited by variable current blocking mechanisms. An important practical complexity is commercial practices of performing J c and I c evaluations based on I c at 77 K and self-field (sf), where connectivity variation dominates over vortex pinning variations. However, at higher fields and lower temperatures, vortex pinning becomes more complex and highly variable, making predictions of I c and J c at arbitrary temperature T, magnetic field H, and field orientation θ, quite uncertain. To address some aspects of this problem, we conducted detailed spool-to-spool performance characterization on recently manufactured REBCO CCs. Despite J c (77 K, sf) varies by only ∼11%, J c (77 K, 1 T) of its minimum and maximum (for H//ab-plane) show variations of ∼21% and ∼32%, respectively. This emphasizes the shortcoming in using J c (77 K, sf) as parameter for evaluating even the low field performance. An even more remarkable spool-to-spool J c variation of ∼68% was observed at 20 K and 15 T for H//ab-plane. To identify the origin of such lack of reproducibility we performed microstructural characterizations, which revealed, within the REBCO layer, large variation in the density of copper oxide (CuO x ) particles ranging from 0.1 to 2 μm in size. We believe that they play a decisive role in reducing the effective cross-section of the REBCO layer by not simply blocking current themselves, but also by nucleating off-axis REBCO grains, whose misoriented grain boundaries adversely impact REBCO grain-to-grain connectivity. The REBCO growth associated with high density CuO x particles also leads to the more disordered spatial arrangement of BaHfO 3 precipitate arrays, which, when self-aligning along the ab-planes, generate stronger pinning enhancing J c (H//ab) at all temperatures. In this way, we established that variations of both connectivity and vortex pinning are thus directly coupled. Our results also explain why the so-called ‘lift-factor’, typically defined by the ratio between I c (T, H) and I c (77 K, sf), frequently turns out to be unreliable.

36 MATERIALS SCIENCE↗

Characterization and nondestructive inspection of additively manufactured materials

Additively manufactured (AM) components often exhibit significant discontinuities and indications without a clear understanding of how they might affect the mechanical properties of a part during qualification and service. This uncertainty is unacceptable for the design and manufacturing of most aerospace components. Current research in both mechanical testing and nondestructive evaluation involves developing methods for characterizing and inspecting AM components as the use of such materials continues to rise. Although several AM manufacturing methods have been developed in recent decades, this paper focuses on AM production-ready processes for a direct metal laser sintering (DMLS) powder bed fusion machine and will provide background on Sandia National Laboratories’ research efforts in this area. Tensile bar samples manufactured using the DMLS powder bed fusion method were inspected in this study, and the results of ultrasonic spectroscopy for assessing internal flaws will be presented. A combination of material property evaluation, microstructural characterization, and nondestructive inspection techniques will also be described. Finally, the results obtained from these material evaluation methods assist in determining inspection limits and methods for qualifying AM materials.

36 MATERIALS SCIENCE↗

Meso-scale microstructural agglomerate quantification in boron carbide using X-ray microcomputed tomography

Highlights: • First known quantification of agglomerate defect distributions comprising of carbonaceous and aluminum nitride phases B{sub 4}C. • In-depth statistical analyses of the size, orientation, and morphology of the defects. • The determination of directional dependence of the hot-pressing direction on the agglomerate distributions. - Abstract: Failure in brittle materials is governed, in part, by the specific microstructure of that material, with heterogeneous microstructures generally leading to reduced mechanical properties and performance. In ceramics used for armor, an increase in compressive strength can be an indicator of improved ballistic performance. In hot-pressed boron carbide (B{sub 4}C) ceramic plates, failure has been attributed to carbonaceous flakes observed on the fracture surfaces of failed specimens. However, this current work shows agglomerates, in addition to the carbonaceous flakes, are present in this boron carbide. The density and distribution of these agglomerates are believed to influence the ballistic performance. Therefore, it is of interest to improve the quantification of meso-scale microstructural agglomerates so that strategies can be developed to mitigate them. This work is focused on the microstructural characterization of dumbbell-shaped compression specimens that were machined from a single tile of pressure-aided densification (PAD) B{sub 4}C, using high-resolution micro-computed tomography (microCT). Large clusters of non-B{sub 4}C agglomerates, up to 125 μm in diameter, were observed in addition to the typical smaller carbonaceous flakes and aluminum-based phases. Agglomerate size distribution, orientation, morphology, and spacing were quantified both parallel and perpendicular to the pressing direction. This defect quantification provides valuable information for a better understanding of the material microstructure which is a critical step in improving armor materials for the future.

36 MATERIALS SCIENCE↗

Extent of interlocking and metallurgical bonding in friction riveting of aluminum alloy to steel

In this study, the joining of 6061-T6 aluminum alloy and DP590 steel using a M42 steel rivet via friction riveting technique is investigated. The surface morphology and microstructure characterization reveal the formation of an anchor zone that imparts mechanical interlock as well as the formation of metallurgical bonds at the interface of aluminum and steel. A combination of interlocking and bonding results in the achievement of a high load-carrying capacity of 5.7 kN during lap shear testing at room temperature. A finite element-based computational model was developed which accurately predicted the lap shear response of the joint. The model revealed that the metallurgical bond formed during fric-riveting adds 39% peak load strength to the joint. An extensive microstructural investigation, post-lap-shear fractography, and the modeling results, together provided insights on the joint failure mechanism. In conclusion, this study highlights that friction riveting is a promising method for aluminum-to-steel dissimilar joining, which is important for lighweighing automotive vehicles for energy efficiency.

36 MATERIALS SCIENCE↗

Effect of Lithium on the Discharge and Corrosion Behavior of Mg-3 wt.% Al Alloy as the Anode for Seawater Activated Battery

The discharge and corrosion behavior of Mg-3 wt.% Al alloys added with different contents of lithium in 3.5 wt.% NaCl aqueous solution is studied by electrochemical methods and microstructure characterization. The results indicate that adding 4 wt.% lithium severely promotes the self-corrosion and the addition of 12 wt.% lithium is not valuable to the spalling of discharge products. In contrast, doping Mg-3 wt.% Al with 8 wt.% lithium negatively shifts the discharge potentials and inhibits the self-discharge, attributed to the dual-phase structure of α-Mg plus β-Li that removes the discharge products and favors the uniform dissolution in the course of discharge. Moreover, the multi-pass rolling with 40% reduction could tailor the microstructure of Mg-3 wt.% Al-8 wt.% Li alloy and further enhance its discharge activity, even though the corrosion resistance is slightly reduced. This means that the rolled Mg-3 wt.% Al-8 wt.% Li sheet is suitable to serve as the anode for seawater activated battery.

36 MATERIALS SCIENCE↗

Design of Novel Precipitate-Strengthened Al-Co-Cr-Fe-Nb-Ni High-Entropy Superalloys

Here, a series of non-equiatomic Al-Co-Cr-Fe-Nb-Ni high-entropy alloys, with varying levels of Co, Nb and Fe, were investigated in an effort to obtain microstructures similar to conventional Ni-based superalloys. Elevated levels of Co were observed to significantly decrease the solvus temperature of the γ' precipitates. Both Nb and Co in excessive concentrations promoted the formation of Laves and NiAl phases that formed either during solidification and remained undissolved during homogenization or upon high-temperature aging. Lowering the content of Nb, Co, or Fe prevented the formation of the eutectic type Laves. In addition, lowering the Co content resulted in a higher number density and volume fraction of the γ' precipitates, while increasing the Fe content led to the destabilization of the γ' precipitates. Various aging treatments were performed which led to different size distributions of the strengthening phase. Results from the microstructural characterization and hardness property assessments of these high-entropy alloys were compared to a commercial, high-strength Ni-based superalloy RR1000. Potentially, precipitation-strengthened high-entropy alloys could find applications replacing Ni-based superalloys as structural materials in power generation applications.

36 MATERIALS SCIENCE↗

Tensile fracture characteristics of nanostructured ferritic alloy 14YWT

High temperature tensile fracture behavior has been characterized for the ferritic alloy 14YWT (SM10 heat) with the composition of Fe-14Cr-3W-0.4Ti (in wt.%) and strengthened by dispersion of nanometer-sized oxygen, titanium, and yttrium rich clusters. Tensile tests were performed at various temperatures ranging from room temperature to 1000 C in a vacuum condition using a nominal strain rate of 10-3s-1. Comparing with the existing oxide dispersion strengthened (ODS) steels such as Eurofer 97 and PM2000, the nanostructured alloy showed much higher yield and tensile strength over the test temperature range, but with lower elongation. Microstructural characterization for fractured tensile specimens was focused on the details of fracture morphology and mechanism to provide a feedback for process improvement. Below 600 C, the fracture surfaces exhibited a quasi-ductile behavior presented by a mixture of dimples and cleavage facets. At or above 600 C, however, the fracture surfaces were fully covered with dimples. The spherical particles that seemed to be oxide or carbide particles were found inside of dimples. It was notable that numerous microcracks were observed on the side surface of broken specimens. Formation of these microcracks is believed to be the main origin of the poor ductility of 14YWT alloy. It is suggested that any grain boundary strengthening measure is essential to improve the fracture property of the alloy.

36 MATERIALS SCIENCE↗

Synthesis, crystal structure, electrical properties, and sodium transport pathways of the new arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6}

A new sodium cobalt (II) arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6} has been synthesized by a solid-state reaction and its crystal structure determined from single crystal X-ray diffraction data. It crystallizes in the monoclinic system, space group C2/m, with a=10.7098(9) Å, b=14.7837(9) Å, c=6.6845(7) Å, and β=105.545(9)°. The structure is described as a three-dimensional framework built up of corner-edge sharing CoO{sub 6}, CoO{sub 4} and AsO{sub 4} polyhedra, with interconnecting channels along [100] in which the Na{sup +} cations are located. The densest ceramics with relative density of 94% was obtained by ball milling and optimization of sintering temperature, and its microstructure characterized by scanning electron microscopy. The electrical properties of the ceramics were studied over a temperature interval from 280 °C to 560 °C using the complex impedance spectroscopy over the range of 13 MHz–5 Hz. The ionic bulk conductivity value of the sample at 360 °C is 2.51 10{sup −5} S cm{sup −1} and the measured activation energy is Ea=1 eV. The sodium migration pathways in the crystal structure were investigated computationally using the bond valence site energy (BVSE) model and classical molecular dynamics (MD) simulations. - Graphical abstract: Correlation between crystal structure, microstructure and ionic conductivity . Display Omitted - Highlights: • A new arsenate Na{sub 4}Co{sub 7}(AsO{sub 4}){sub 6} was prepared by solid state reaction. • Its crystal structure was determined by powder X-ray diffraction. • Na{sup +} ionic conductivity was probed by complex impedance spectroscopy. • Na{sup +} conduction pathways were modeled by bond-valence method and molecular dynamics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparing structure-property evolution for PM-HIP and forged alloy 625 irradiated with neutrons to 1 dpa

The nuclear power industry has growing interest in qualifying powder metallurgy with hot isostatic pressing (PM-HIP) to replace traditional alloy fabrication methods for reactor structural components. But there is little known about the response of PM-HIP alloys to reactor conditions. This study directly compares the response of PM-HIP to forged Ni-base Alloy 625 under neutron irradiation doses ~0.5–1 displacements per atom (dpa) at temperatures ranging ~321–385 °C. Post-irradiation examination involves microstructure characterization, ASTM E8 uniaxial tensile testing, and fractography. Up through 1 dpa, PM-HIP Alloy 625 appears more resistant to irradiation-induced cavity nucleation than its forged counterpart, and consequently experiences significantly less hardening. This observed difference in performance can be explained by the higher initial dislocation density of the forged material, which represents an interstitial-biased sink that leaves a vacancy supersaturation to nucleate cavities. These findings show promise for qualification of PM-HIP Alloy 625 for nuclear applications, although higher dose studies are needed to assess the steady-state irradiated microstructure.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Destructive Examination of a FeCrAl-UO 2 Irradiation Test

Several destructive postirradiation examinations were performed on an irradiation specimen that coupled an early iron-chromium-aluminum (FeCrAl) candidate alloy cladding with UO2 pellets. This irradiation test was designed to investigate the early life performance and compatibility of the FeCrAl-UO 2 cladding-fuel system under prototypic light water reactor neutronic conditions. Additionally, these tests were expected to provide neutron irradiated samples for severe accident testing of this fuel system. The irradiation studied in this work was part of the ATF-1 series of drop-in style irradiations performed in the Idaho National Laboratory Advanced Test Reactor. The rodlet studied in this work is one of three similar rodlets irradiated in ATF-1 that had approximately 7.6 cm of cladding machined from a wrought FeCrAl alloy and fueled with a 6.1 cm stack of UO 2 pellets. The outer diameter of the cladding was ~0.94 cm and the inner diameter was ~0.83 cm. After irradiation and non-destructive examination in Idaho this rodlet was shipped to the Oak Ridge National Laboratory hot-cells for further examination. The irradiated rodlet was sectioned into several samples for microstructural, micromechanical, and severe accident testing. During sectioning, it was noted that the fuel was not firmly bonded to the cladding and could be readily removed from small cladding slices. Microstructural characterization of fuel cross sections also revealed no significant interaction between the fuel and the cladding. Samples were also prepared for microhardness testing. To prepare for high temperature oxidation testing, the fuel was dissolved from segments of the cladding. High temperature oxidation testing of cladding segments was performed at 1200°C and 1300°C in a steam environment. Comparisons between the oxidation of this FeCrAl alloy in its neutron irradiated state, as-fabricated state, and the oxidation of Zircaloy-2 are made. The oxidation testing will be followed by ring compression testing to evaluate ductility. The microstructure of the samples after oxidation and ring compression testing will also be analyzed.

Harp, Jason↗

Enhancing cold spray coatings: Microstructural dynamics and performance attributes of Inconel 625 with chromium carbide incorporation for hydropower applications

The incorporation of chromium carbide (CrC) particles into the cold spray (CS) process is known to mitigate nozzle clogging, although at the expense of deposition efficiency. This study explores the intricate microstructural changes induced by varying amounts of CrC powder (12.5 % and 6 %) in conjunction with Inconel-625 (Inc-625) powder. The deposition was carried out onto A27 cast steel under different CS parameters. Microstructural characterization, including detailed electron microscopy studies, reveals a complex yet structurally stable coating. Noteworthy features include grain fragmentation and a cellular structure enriched with Nb and Mo, with minimal plastic deformation of CrC in the matrix. The cold-sprayed coatings exhibit a significant (~4 times) increase in microhardness compared to the A27 substrate. Mechanical and cavitation erosion properties were systematically investigated. Coatings subjected to higher particle energy conditions with a gas pressure of 600 psi and gas temperature of 650 °C, demonstrated superior resistance to cavitation erosion. This resistance is attributed to a combination of factors, including microstructural characteristics and porosity. Altogether, the study provides valuable insights into the structural dynamics and performance of CS coatings enriched with CrC particles.

A27 cast steel↗

Ultrasonic Spot Welding of AZ31B to Galvanized Mild Steel

Ultrasonic spot welds were made between sheets of 0.8-mm-thick hot-dip-galvanized mild steel and 1.6-mm-thick AZ31B-H24. Lap-shear strengths of 3.0-4.2 kN were achieved with weld times of 0.3-1.2 s. Failure to achieve strong bonding of joints where the Zn coating was removed from the steel surface indicate that Zn is essential to the bonding mechanism. Microstructure characterization and microchemical analysis indicated temperatures at the AZ31-steel interfaces reached at least 344 C in less than 0.3 s. The elevated temperature conditions promoted annealing of the AZ31-H24 metal and chemical reactions between it and the Zn coating.

36 MATERIALS SCIENCE↗

Fundamental Studies of Irradiation-Induced Modifications in Microstructural Evolution and Mechanical Properties of Advanced Alloys

This final technical report summarizes the research performed during October 2014 and December 2017, with a focus on investigating the radiation-induced microstructural and mechanical property modifications in optimized advanced alloys for sodium-cooled fast reactor (SFR) structural applications. To accomplish these objectives, the radiation responses of several different advanced alloys, including austenitic steel Alloy 709 (A709) and 316H, and ferritic/ martensitic Fe–9Cr steels T91 and G92, were investigated using a combination of microstructure characterizations and nanoindentation measurements. Different types of irradiation, including ex situ bulk ion irradiation and in situ transmission electron microscopy (TEM) ion irradiation, were employed in this study. Radiation-induced dislocations, precipitates, and voids were characterized by TEM. Scanning transmission electron microscopy with energy dispersive X-ray spectroscopy (STEM-EDS) and/or atom probe tomography (APT) were used to study radiation-induced segregation and precipitation. Nanoindentation was used for hardness measurements to study irradiation hardening. Austenitic A709 and 316H was bulk-irradiated by 3.5 MeV Fe ++ ions to up to 150 peak dpa at 400, 500, and 600°. Compared to neutron-irradiated stainless steel (SS) 316, the Frank loop density of ion-irradiated A709 shows similar dose dependence at 400°, but very different temperature dependence. Due to the noticeable difference in the initial microstructure of A709 and 316H, no systematic comparison on the Frank loops in A709 vs 316H was made. It would be helpful that future ion irradiation study on 316 stainless steel could be conducted to directly compare the temperature dependence of Frank loop density in ion-irradiated 316 SS with that in neutron-irradiated 316 SS. In addition, future neutron irradiation on A709 at 400–600° at relative high dose (≥10 dpa) can be carried out to compare with ion-irradiated A709. The radiation-induced segregation (RIS) of Ni and Si was observed in both A709 and 316H in all irradiated conditions and was found at various sinks: line dislocations, dislocation loops, void surfaces, carbide-matrix interfaces, etc. Radiation also induced the formation of Ni,Si-rich precipitates. As suggested in a previous study on neutron-irradiated 316 stainless steel, one possible consequence of the significant RIS of Si is that the enrichment at defect sinks depletes the silicon in the matrix, which can lead to enhanced void nucleation rate. The enrichment of Ni and Si is accompanied by the depletion of Cr at defect sinks, which could also affect the corrosion resistance. Radiation-induced change in the orientation relationship of pre-existing MX precipitates was observed at 600°. It is believed that this change is associated with the network dislocations formed under irradiation. The underlying mechanism is still not well understood. This change could be a positive indication that the MX precipitates can survive high density network dislocations. It would be helpful if neutron irradiation at similar dose conditions could be carried out to verify that this effect is not unique for ion irradiation. Intragranular Cr-rich carbides with a core-shell structure, i.e. Cr-rich carbide core and Ni,Si-rich shell was found at 500° and 600° in the highest dose (150 peak dpa) specimens. Coarse voids (30 nm in diameter) were only commonly found at 500° in the 50 and 150 peak dpa specimens in regions less than 750 nm in depth. The highest swelling for A709 irradiated to 50 and 150 peak dpa at 500° is about 0.44% and 0.37%, respectively. Due to the choice of 100 degree temperature intervals, this study did not attempt to precisely identify peak void swelling conditions, merely the range of irradiation temperatures where this could be a concern. It is known high-dose ion irradiation can significantly suppress void nucleation. Future neutron irradiation in the 500–600° range (without considering the temperature shift) is needed to determine the onset of accelerated void swelling (possibly at lower dose).

36 MATERIALS SCIENCE↗

Laser annealing of electrodeposited CuInSe 2 semiconductor precursors: experiment and modeling

Laser annealing can reduce the annealing time required to form Cu(In,Ga)(S,Se) 2 (CIGSe) thin films for use in thin film photovoltaics to a single second timescale, if not faster. In this work, we use microstructural characterization coupled with modeling of the optical and thermal properties to understand the laser annealing of three types of electrodeposited precursor stacks for the CIGSe parent compound CuInSe 2 . The precursor films are: stacked elemental layers Cu/In/Se, stacked binary selenides In 2 Se 3 /Cu 2– x Se, and a single layer of coelectrodeposited Cu–In–Se. Conceptually, these stacks are ordered in terms of decreasing stored chemical and interfacial potential free energy, consideration of which predicts that the formation of large grained CuInSe 2 from the stacked elemental layers would be the most exothermic and thus most rapid process. However we find that microstructural details of the electrodeposited films such as void fraction present in the stacked binary selenides dramatically alter the heat and mass flow. Additionally, modeling of the optical absorption within the elemental stacked precursor suggests extremely localized heating at the In/Se interface resulting in significant Se loss. Despite its lower chemical potential energy, the coelectrodeposited CuInSe 2 precursor's more uniform optical absorption of near-bandgap light coupled with its compact, low void fraction microstructure of nano-sized grains results in the most optimal recrystallization and compositional homogenization via interdiffusion. Furthermore this annealed layer formed a working device with a short circuit current density of 23 mA cm –2 . As a result, this combined modeling and experimental investigation underscores the need to consider practical micro- and nanostructure-dependent properties as well as the optical absorption and not simply thermodynamics when designing accelerated two step deposition and annealing processes for compound semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗