SEARCH · Search NASA

Results for “open loop”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Periodic-disturbance accommodating control of the Space Station for asymptotic momentum management

Periodic-disturbance accommodating control is investigated for asymptotic momentum management of control moment gyros used as primary actuating devices for the Space Station. The proposed controller utilizes the concepts of quaternion feedback control and periodic-disturbance accommodation to achieve oscillations about the constant torque equilibrium attitude, while minimizing the control effort required. Three-axis coupled equations of motion, written in terms of quaternions, are derived for roll/yaw controller design and stability analysis. The quaternion feedback controller designed using the linear-quadratic regulator synthesis technique is shown to be robust for a wide range of pitch angles. It is also shown that the proposed controller tunes the open-loop unstable vehicle to a stable oscillatory motion which minimizes the control effort needed for steady-state operations.

Warren, Wayne↗

NASA NTRS1989

Evaluation of a technique for predicting longitudinal pilot-induced-oscillations

A technique for predicting the susceptibility of an aircraft to longitudinal pilot-induced-oscillations (PIO's) is evaluated using 62 configurations from a pair of flight tests involving the NT-33 variable stability aircraft. The technique is based upon the characteristics of the open-loop pilot/vehicle system for attitude control as predicted by the Optimal Control Model (OCM) of the human pilot. The OCM is simplified so that only the index of performance weighting coefficients need to be considered as problem variables and a simple technique for generating these coefficients is reviewed.

Hess, R. A.↗

NASA NTRS1989

Thrust vectoring effect on time-optimal 90 degrees angle of attack pitch up maneuvers of a high alpha fighter aircraft

Using thrust vectoring, the problem of pitching up a high alpha fighter aircraft to 90 degrees angle of attack in minimum time is considered. Pontryagin's maximum principle is used together with a two-point boundary value numerical algorithm to derive open-loop controls for various parameterized limits on thrust vectoring angles. Without thrust vectoring, a high alpha fighter with initial conditions 0.6 Mach number and 15,000 feet requires 7.0 seconds to pitch-up to 90 degrees. However, with 20-degree angle thrust vectoring, the pitch-up takes only 1.5 seconds with a final Mach number of 0.47. Also, the gain in altitude is less than 100 feet. More important, additional thrust vectoring yields litle benefit beyond the 20-degree angles. This paper describes control solutions in detail for thrust vectoring angles between 0 and 90 degrees.

Stalford, Harold↗

NASA NTRS1989

Motion and force control for multiple cooperative manipulators

The motion and force control of multiple robot arms manipulating a commonly held object is addressed. A general control paradigm that decouples the motion and force control problems is introduced. For motion control, there are three natural choices: (1) joint torques, (2) arm-tip force vectors, and (3) the acceleration of a generalized coordinate. Choice (1) allows a class of relatively model-independent control laws by exploiting the Hamiltonian structure of the open-loop system; (2) and (3) require the full model information but produce simpler problems. To resolve the nonuniqueness of the joint torques, two methods are introduced. If the arm and object models are available, the allocation of the desired end-effector control force to the joint actuators can be optimized; otherwise the internal force can be controlled about some set point. It is shown that effective force regulation can be achieved even if little model information is available.

Wen, John T.↗

NASA NTRS1989

Backup nutation damping strategy for the Galileo spacecraft

A discussion is presented of the design and testing of remedial measures that can be taken to achieve reasonable nutation damping of the Galileo spacecraft in the event of failure of its boom damper in flight. One scheme exploits the effects of payload motion on the nutational stability of a spinning spacecraft. However, the spacecraft-motion-compensation algorithm can only be used if the scan platform bore sight is pointed in a direction chosen to produce rapid damping of spacecraft nutation. A second method suggested for nutation damping is a thruster-based open-loop control algorithm, utilizing a pair of thrusters as actuators.

Eke, Fidelis O.↗

NASA NTRS1989

Analysis of the T-97 Space Shuttle Solid Rocket Motor test facility

The history of the analyses for the hydraulic force control systems of the T-97 test facility is presented. Two approaches that were investigated for softening the hydraulic systems for improved performance are presented. A valve modification and inclusion of a proportional-integral controller that finally stabilized the system are described. A simulated test case is shown and compared to actual test data from the QM-7 test. The simulated results are very close to the real results but indicate a slightly higher open-loop gain than for the real system.

Williamson, Marlin J.↗

NASA NTRS1990

Output Control Using Feedforward And Cascade Controllers

Report presents theoretical study of open-loop control elements in single-input, single-output linear system. Focus on output-control (servomechanism) problem, in which objective is to find control scheme that causes output to track certain command inputs and to reject certain disturbance inputs in steady state. Report closes with brief discussion of characteristics and relative merits of feedforward, cascade, and feedback controllers and combinations thereof.

Seraji, Homayoun↗

NASA NTRS1989

Periodic-disturbance accommodating control of the space station for asymptotic momentum management

Warren, Wayne↗

NASA NTRS1989

Guidance and Control strategies for aerospace vehicles

A neighboring optimal guidance scheme was devised for a nonlinear dynamic system with stochastic inputs and perfect measurements as applicable to fuel optimal control of an aeroassisted orbital transfer vehicle. For the deterministic nonlinear dynamic system describing the atmospheric maneuver, a nominal trajectory was determined. Then, a neighboring, optimal guidance scheme was obtained for open loop and closed loop control configurations. Taking modelling uncertainties into account, a linear, stochastic, neighboring optimal guidance scheme was devised. Finally, the optimal trajectory was approximated as the sum of the deterministic nominal trajectory and the stochastic neighboring optimal solution. Numerical results are presented for a typical vehicle. A fuel-optimal control problem in aeroassisted noncoplanar orbital transfer is also addressed. The equations of motion for the atmospheric maneuver are nonlinear and the optimal (nominal) trajectory and control are obtained. In order to follow the nominal trajectory under actual conditions, a neighboring optimum guidance scheme is designed using linear quadratic regulator theory for onboard real-time implementation. One of the state variables is used as the independent variable in reference to the time. The weighting matrices in the performance index are chosen by a combination of a heuristic method and an optimal modal approach. The necessary feedback control law is obtained in order to minimize the deviations from the nominal conditions.

Hibey, J. L.↗

NASA NTRS1989

Cooperative control of two active spacecraft during proximity operations

A cooperative autopilot is developed for the control of the relative attitude, relative position and absolute attitude of two maneuvering spacecraft during on orbit proximity operations. The autopilot consists of an open-loop trajectory solver which computes a nine dimensional linearized nominal state trajectory at the beginning of each maneuver and a phase space regulator which maintains the two spacecraft on the nominal trajectory during coast phases of the maneuver. A linear programming algorithm is used to perform jet selection. Simulation tests using a system of two space shuttle vehicles are performed to verify the performance of the cooperative controller and comparisons are made to a traditional passive target/active pursuit vehicle approach to proximity operations. The cooperative autopilot is shown to be able to control the two vehicle system when both the would be pursuit vehicle and the target vehicle are not completely controllable in six degrees of freedom. The cooperative controller is also shown to use as much as 37 percent less fuel and 57 percent fewer jet firings than a single pursuit vehicle during a simple docking approach maneuver.

Polutchko, Robert J.↗

NASA NTRS1990

Digital-flutter-suppression-system investigations for the active flexible wing wind-tunnel model

Active flutter suppression control laws were designed, implemented, and tested on an aeroelastically-scaled wind tunnel model in the NASA Langley Transonic Dynamics Tunnel. One of the control laws was successful in stabilizing the model while the dynamic pressure was increased to 24 percent greater than the measured open-loop flutter boundary. Other accomplishments included the design, implementation, and successful operation of a one-of-a-kind digital controller, the design and use of two simulation methods to support the project, and the development and successful use of a methodology for on-line controller performance evaluation.

Perry, Boyd, III↗

NASA NTRS1989

A distributed finite-element modeling and control approach for large flexible structures

An unconventional framework is described for the design of decentralized controllers for large flexible structures. In contrast to conventional control system design practice which begins with a model of the open loop plant, the controlled plant is assembled from controlled components in which the modeling phase and the control design phase are integrated at the component level. The developed framework is called controlled component synthesis (CCS) to reflect that it is motivated by the well developed Component Mode Synthesis (CMS) methods which were demonstrated to be effective for solving large complex structural analysis problems for almost three decades. The design philosophy behind CCS is also closely related to that of the subsystem decomposition approach in decentralized control.

Young, K. D.↗

NASA NTRS1989

The coupling effects of kinematics and flexibility on the Lagrangian dynamic formulation of open chain deformable links

A nonlinear Lagrangian formulation for the spatial kinematic and dynamic analysis of open chain deformable links consisting of cylindrical joints that connect pairs of flexible links is developed. The special cases of revolute or prismatic joint can also be obtained from the kinematic equations. The kinematic equations are described using a 4x4 matrix method. The configuration of each deformable link in the open loop kinematic chain is identified using a coupled set of relative joint variables, constant geometric parameters, and elastic coordinates. The elastic coordinates define the link deformation with respect to a selected joint coordinate system that is consistent with the kinematic constraints on the boundary of the deformable link. These coordinates can be introduced using approximation techniques such as Rayleigh-Ritz method, finite element technique or any other desired approach. The large relative motion between two neighboring links are defined by a set of joint coordinates which describes the large relative translational and rotational motion between two neighboring joint coordinate systems. The origin of these coordinate systems are rigidly attached to the neighboring links at the joint definition points along the axis of motion.

Changizi, Koorosh↗

NASA NTRS1989

OPTICON: Pro-Matlab software for large order controlled structure design

A software package for large order controlled structure design is described and demonstrated. The primary program, called OPTICAN, uses both Pro-Matlab M-file routines and selected compiled FORTRAN routines linked into the Pro-Matlab structure. The program accepts structural model information in the form of state-space matrices and performs three basic design functions on the model: (1) open loop analyses; (2) closed loop reduced order controller synthesis; and (3) closed loop stability and performance assessment. The current controller synthesis methods which were implemented in this software are based on the Generalized Linear Quadratic Gaussian theory of Bernstein. In particular, a reduced order Optimal Projection synthesis algorithm based on a homotopy solution method was successfully applied to an experimental truss structure using a 58-state dynamic model. These results are presented and discussed. Current plans to expand the practical size of the design model to several hundred states and the intention to interface Pro-Matlab to a supercomputing environment are discussed.

Peterson, Lee D.↗

NASA NTRS1990

An inverse dynamic method yielding flexible manipulator state trajectories

An inverse dynamic equation for a flexible manipulator is derived in a state form. By dividing the inverse system into the causal part and the anticausal part, torque is calculated in the time domain for a certain end point trajectory, as well as trajectories of all state variables. The open loop control of the inverse dynamic method shows an excellent result in simulation. For practical applications, a control strategy adapting feedback tracking control to the inverse dynamic feedforward control is illustrated, and its good experimental result is presented.

Kwon, Dong-Soo↗

NASA NTRS1990

Active control of aerothermoelastic effects for a conceptual hypersonic aircraft

Procedures for and results of aeroservothermoelastic studies are described. The objectives of these studies were to develop the necessary procedures for performing an aeroelastic analysis of an aerodynamically heated vehicle and to analyze a configuration in the classical cold state and in a hot state. Major tasks include the development of the structural and aerodynamic models, open loop analyses, design of active control laws for improving dynamic responses and analyses of the closed loop vehicles. The analyses performed focused on flutter speed calculations, short period eigenvalue trends and statistical analyses of the vehicle response to controls and turbulence. Improving the ride quality of the vehicle and raising the flutter boundary of the aerodynamically-heated vehicle up to that of the cold vehicle were the objectives of the control law design investigations.

Heeg, Jennifer↗

NASA NTRS1989

Portable Dextrous Force Feedback Master for robot telemanipulation (PDMFF)

A major drawback of open loop masters is a lack of force feedback, limiting their ability to perform complex tasks such as assembly and repair. Researchers present a simple dextrous force feedback master for computer assisted telemanipulation. The device is compact, portable and can be held in the operator hand, without the need for a special joystick or console. The system is capable of both position feed forward and force feedback, using electronic position sensors and a pneumatic micro-actuator. The level of forces exercised by the pneumatic actuator is such that near rigidity may be attained. Experimental results showing good system linearity and small time lag are given.

Burdea, Grigore C.↗

NASA NTRS1989

Kinematic sensitivity of robot manipulators

Kinematic sensitivity vectors and matrices for open-loop, n degrees-of-freedom manipulators are derived. First-order sensitivity vectors are defined as partial derivatives of the manipulator's position and orientation with respect to its geometrical parameters. The four-parameter kinematic model is considered, as well as the five-parameter model in case of nominally parallel joint axes. Sensitivity vectors are expressed in terms of coordinate axes of manipulator frames. Second-order sensitivity vectors, the partial derivatives of first-order sensitivity vectors, are also considered. It is shown that second-order sensitivity vectors can be expressed as vector products of the first-order sensitivity vectors.

Vuskovic, Marko I.↗