SEARCH · Search NASA

Results for “process optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

All sources NASA NTRS DOE OSTI

NASA NTRS1989

Singular trajectories for time-optimal half-loop maneuvers of a high alpha fighter aircraft

Consideration is given to the problem of deriving a time-optimal open-loop control for the half-loop maneuver of a high-alpha aircraft, with initial conditions Mach 0.6 and 15,000 feet. Pontriagin's maximum principle is used to derive candidate optimal solutions. Using the two-point boundary-value algorithm, the flight path angle is maximized for various increasing specified final times until a final time of 13.6 sec yields a 180-deg flight-path angle. As the final time increased from 0.0 to 13.6 sec, the optimization process revealed 13 distinct switching structures of the control law, of which 11 contained singular arcs, and two had double singular arcs.

Hoffman, Eric↗

NASA NTRS1989

Acoustic design considerations: Review of rotor acoustic sources

It is not sufficient to optimize a rotor design in terms of a single noise level calculated for a single flight condition and a single measurement location. The various noise sources, their frequency content, amplitude, and directivity as a function of operating condition must be considered. A summary of the frequency ranges, directivity patterns and the most important operational and design parameters for major rotor noise sources is presented. It is difficult to generalize design requirements for rotor noise because the acoustic output varies so widely depending on the noise source, flight condition, measurement location, and frequency range. However, assuming the rotor must lift a fixed nominal payload and operate over a wide range of flight conditions, three general design guidelines can be stated: (1) minimize tip Mach number; (2) minimize blade thickness in the tip region; and (3) minimize gradients in the spanwise lift distribution in the tip region. Constraints on blade thickness, maximum values for hover tip Mach number, advancing tip Mach number and spanwise lift coefficient gradient will be specified during the aerodynamic, dynamic and structural optimization process. The rotor noise sources to be considered include the low frequency loading and thickness noise, and the higher frequency noise due to blade-vortex interactions (BVI). The analyses to be employed will include the comprehensive rotor analysis and design program CAMRAD and the rotor noise prediction program WOPWOP.

Martin, Ruth M.↗

NASA NTRS1990

Secondary electron emission characteristics of molybdenum-masked, ion-textured OFHC copper

A method for producing a uniform, highly textured surface on oxygen-free, high conductivity (OFHC) copper by ion bombardment using sputtered molybdenum as a texture-inducing masking film was developed and used to provide samples for study. The purpose was to develop a basically OFHC copper surface having very low secondary electron emission characteristics. Surfaces having low secondary electron emission are a requirement for the electrodes of very high efficiency multistage depressed collectors (MDC's). Such MDC's are used in microwave amplifier traveling wave tubes for space communications and other applications. OFHC copper is the material most commonly used for MDC electrodes because it has high thermal conductivity, it is easy to machine, and its fabrication and brazing procedures are well established. However, its untreated surface displays relatively very high levels of secondary electron emissions. Textured OFHC copper samples were tested for true secondary electron emission and relative reflected primary electron yield at primary electron beam energy levels from 200 to 2000 eV and at direct (0 deg) to oblique (60 deg) beam impingement angles. The test results for three of the samples, each of which was processed in a slightly different way, are compared with each other and with test results for a machined OFHC copper sample. Although the textured samples are not represented here as having been processed optimally, their measured secondary electron emission characteristics are significantly lower than those of the untreated OFHC copper sample over the range of conditions studied. Importantly, the relative reflected primary electron yield of one of the textured samples is conspicuously lower than that of the others. Clearly, with further development, the molybdenum-masked ion-textured OFHC copper surface will be a promising material for high-efficiency MDC electrodes.

Curren, Arthur N.↗

NASA NTRS1990

Field oriented control of induction motors

Induction motors have always been known for their simple rugged construction, but until lately were not suitable for variable speed or servo drives due to the inherent complexity of the controls. With the advent of field oriented control (FOC), however, the induction motor has become an attractive option for these types of drive systems. An FOC system which utilizes the pulse population modulation method to synthesize the motor drive frequencies is examined. This system allows for a variable voltage to frequency ratio and enables the user to have independent control of both the speed and torque of an induction motor. A second generation of the control boards were developed and tested with the next point of focus being the minimization of the size and complexity of these controls. Many options were considered with the best approach being the use of a digital signal processor (DSP) due to its inherent ability to quickly evaluate control algorithms. The present test results of the system and the status of the optimization process using a DSP are discussed.

Burrows, Linda M.↗

NASA NTRS1990

Minimum Weight Design of a Leaf Spring Tapered in Thickness and Width for the Hubble Space Telescope-Space Support Equipment

A linear elastic solution to the problem of minimum weight design of cantilever beams with variable width and depth is presented. The solution shown is for the specific application of the Hubble Space Telescope maintenance mission hardware. During these maintenance missions, delicate instruments must be isolated from the potentially damaging vibration environment of the space shuttle cargo bay during the ascent and descent phases. The leaf springs are designed to maintain the isolation system natural frequency at a level where load transmission to the instruments in a minimum. Nonlinear programming is used for the optimization process. The weight of the beams is the objective function with the deflection and allowable bending stress as the constraint equations. The design variables are the width and depth of the beams at both the free and the fixed ends.

Rodriguez, P. I.↗

NASA NTRS1990

Synthetic-aperture-radar imaging of the ocean surface using the slightly-rough facet model and a full surface-wave spectrum

A new model of synthetic-aperture-radar (SAR) imaging of ocean waves is described. The model is based on mapping individual, slightly-rough surface facets through the SAR processor into the image and responses of the facets in the image domain are added together coherently to give the composite image. A windowing technique allows both the orbital motion and the phase velocity of the long waves to be included. It is determined that the azimuthal cut-off is due to a smearing of the response of the facets in the image induced by the random orbital motion of the intermediate large-scale waves and that the focus adjustment that gives the greatest image contrast is half the phase velocity of the dominant long wave. The optimal processing technique, however, may consist of spatially offsetting the multiple looks on the image domain to compensate the propagation of long waves during the integration time of the SAR.

West, James C.↗

NASA NTRS1991

A comparison of Manchester symbol tracking loops for block 5 applications

The linearized tracking errors of three Manchester (biphase coded) symbol tracking loops are compared to determine which is appropriate for Block 5 receiver applications. The first is a nonreturn to zero (NRZ) symbol synchronizer loop operating at twice the symbol rate (NRZ x 2) so that it operates on half symbols. The second near optimally processes the mid-symbol transitions and ignores the between symbol transitions. In the third configuration, the first two approaches are combined as a hybrid to produce the best performance. Although this hybrid loop is the best at low symbol signal to noise ratios (SNRs), it has about the same performance as the NRZ x 2 loop at higher SNRs (greater than 0-dB E sub s/N sub 0). Based on this analysis, it is tentatively recommended that the hybrid loop be implemented for Manchester data in the Block 5 receiver. However, the high data rate case and the hardware implications of each implementation must be understood and analyzed before the hybrid loop is recommended unconditionally.

Holmes, J. K.↗

NASA NTRS1991

Charged particle LET-spectra measurements aboard LDEF

The linear energy transfer (LET) spectra of charged particles was measured in the 5 to 250 keV/micron (water) interval with CR-39 and in the 250 to 1000 keV/micron (water) interval with polycarbonate plastic nuclear track detectors (PNTDs) under different shielding depths in the P0006 experiment. The optimal processing conditions were determined for both PNTDs in relation to the relatively high track densities due to the long term exposure in space. The total track density was measured over the selected samples, and tracks in coincidence on the facing surfaces of two detector sheets were selected for measuring at the same position on each sheet. The Short Range (SR) and Galactic Cosmic Ray (GCR) components were measured separately. The integral dose and dose rate spectra of charged particles are also given. The high LET portion of the LET spectra was measured with high statistical accuracy. This is a unique result of this experiment due to the low flux of this type of particle under typical shielding conditions.

Csige, I.↗

NASA NTRS1990

Application of global sensitivity equations in multidisciplinary aircraft synthesis

The present paper investigates the applicability of the Global Sensitivity Equation (GSE) method in the multidisciplinary synthesis of aeronautical vehicles. The GSE method provides an efficient approach for representing a large coupled system by smaller subsystems and accounts for the subsystem interactions by means of first-order behavior sensitivities. This approach was applied in an aircraft synthesis problem with performance constraints stemming from the disciplines of structures, aerodynamics, and flight mechanics. Approximation methods were considered in an attempt to reduce problem dimensionality and to improve the efficiency of the optimization process. The influence of efficient constraint representations, the choice of design variables, and design variable scaling on the conditioning of the system matrix was also investigated.

Hajela, P.↗

NASA NTRS1991

Concurrent material-fabrication optimization of metal-matrix laminates under thermo-mechanical loading

A methodology is developed to tailor fabrication and material parameters of metal-matrix laminates for maximum loading capacity under thermomechanical loads. The stresses during the thermomechanical response are minimized subject to failure constrains and bounds on the laminate properties. The thermomechanical response of the laminate is simulated using nonlinear composite mechanics. Evaluations of the method on a graphite/copper symmetric cross-ply laminate were performed. The cross-ply laminate required different optimum fabrication procedures than a unidirectional composite. Also, the consideration of the thermomechanical cycle had a significant effect on the predicted optimal process.

Saravanos, D. A.↗

NASA NTRS1990

Field oriented control of induction motors

Burrows, Linda M.↗

NASA NTRS1990

Polarization studies of Zeeman affected spectral lines using the MSFC magnetograph

The Marshall Space Flight Center (MSFC) vector magnetograph records polarization images of absorption lines that are sensitive to magnetic fields. A method is presented for analyzing the Stokes spectral-line profiles of a photospheric Fe I absorption line (5250.2 A) which is influenced by the Zeeman effect. Using nonlinear least-square optimization, the observed Stokes profiles are compared with those generated from the theoretical solution of the polarized radiative transfer equations. The optimization process accounts for the spectral convolution of the source and the MSFC vector magnetograph. The resulting physical properties of the active region producing the polarized light are discussed.

Balasubramaniam, K. S.↗

NASA NTRS1991

Advanced transport design using multidisciplinary design optimization

This paper describes the results of the first implementation of multidisciplinary design optimisation (MDO) techniques by undergraduates ina design course. The objective of the work was to design a civilian transport aircraft of the Boeing 777 class. The first half of the two semester design course consisted of application of traditional sizing methods and techniques to form a baseline aircraft. MDO techniques were then applied to this baseline design. This paper describes the evolution of the design with special emphasis on the application of MDO techniques, and presents the results of four iterations through the design space. Minimization of take-off gross weight was the goal of the optimization process. The resultant aircraft derived from the MDO procedure weighed approximately 13,382 lbs (2.57 percent) less than the baseline aircraft.

Barnum, Jennifer↗

NASA NTRS1991

Advanced techniques and technology for efficient data storage, access, and transfer

Advanced techniques for efficiently representing most forms of data are being implemented in practical hardware and software form through the joint efforts of three NASA centers. These techniques adapt to local statistical variations to continually provide near optimum code efficiency when representing data without error. Demonstrated in several earlier space applications, these techniques are the basis of initial NASA data compression standards specifications. Since the techniques clearly apply to most NASA science data, NASA invested in the development of both hardware and software implementations for general use. This investment includes high-speed single-chip very large scale integration (VLSI) coding and decoding modules as well as machine-transferrable software routines. The hardware chips were tested in the laboratory at data rates as high as 700 Mbits/s. A coding module's definition includes a predictive preprocessing stage and a powerful adaptive coding stage. The function of the preprocessor is to optimally process incoming data into a standard form data source that the second stage can handle.The built-in preprocessor of the VLSI coder chips is ideal for high-speed sampled data applications such as imaging and high-quality audio, but additionally, the second stage adaptive coder can be used separately with any source that can be externally preprocessed into the 'standard form'. This generic functionality assures that the applicability of these techniques and their recent high-speed implementations should be equally broad outside of NASA.

Rice, Robert F.↗

NASA NTRS1992

Charged particle LET-spectra measurements aboard LDEF

The linear energy transfer (LET) spectra of charged particles was measured in the 5 to 250 keV/micron (water) interval with CR-39 and in the 500 to 1500 keV/micron (water) interval with polycarbonate plastic nuclear track detectors (PNTDs) under different shielding depths in the P0006 experiment. The optimal processing conditions were determined for both PNTDs in relation to the relatively high track densities due to the long term exposure in space. The total track density was measured over the selected samples, and tracks in coincidence on the facing surfaces of two detector sheets were selected for measuring at the same position on each sheet. The short range (SR) and Galactic Cosmic Ray (GCR) components were measured separately with CR-39 PNTDs and the integral dose and dose rate spectra of charged particles were also determined. The high LET portion of the LET spectra was measured with polycarbonate PNTDs with high statistical accuracy. This is a unique result of this exposure due to the low flux of these types of particles for typical spaceflight durations. The directional dependence of the charged particles at the position of the P0006 experiment was also studied by four small side stacks which surrounded the main stack and by analyzing the dip angle and polar angle distributions of the measured SR and GCR particle tracks in the main stack.

Csige, I.↗

NASA NTRS1992

Integrating aerodynamics and structures in the minimum weight design of a supersonic transport wing

An approach is presented for determining the minimum weight design of aircraft wing models which takes into consideration aerodynamics-structure coupling when calculating both zeroth order information needed for analysis and first order information needed for optimization. When performing sensitivity analysis, coupling is accounted for by using a generalized sensitivity formulation. The results presented show that the aeroelastic effects are calculated properly and noticeably reduce constraint approximation errors. However, for the particular example selected, the error introduced by ignoring aeroelastic effects are not sufficient to significantly affect the convergence of the optimization process. Trade studies are reported that consider different structural materials, internal spar layouts, and panel buckling lengths. For the formulation, model and materials used in this study, an advanced aluminum material produced the lightest design while satisfying the problem constraints. Also, shorter panel buckling lengths resulted in lower weights by permitting smaller panel thicknesses and generally, by unloading the wing skins and loading the spar caps. Finally, straight spars required slightly lower wing weights than angled spars.

Barthelemy, Jean-Francois M.↗

NASA NTRS1992

The Enabler: A reevaluation of design concepts and construction of a scaled model

The basic objective of the student's work this quarter was to make an in depth examination of the design concepts used on the lunar vehicle 'The Enabler'. Several changes were made to the vehicle including a redesigned wheel, a more compact boom and a reduced articulation angle. The vehicle's final dimensions were determined through an optimization process by defining mathematical equations for several of the vehicle's defined objectives. These included the ability to scale a one meter object, traverse a one meter crevice, and maintain a wheel-to-wheel clearance of three inches while at maximum articulation. The final dimensions of the vehicle were used to construct an approximate 1/4 scale model of the chassis and wheels. The boom, however, was constructed on a 1/5 scale (from the original design). This was due to the redesign of the boom and the limitations of the constructing material and PVC fittings.

Bess, David↗

NASA NTRS1992

Optimum Design of High Speed Prop-Rotors

The objective of this research is to develop optimization procedures to provide design trends in high speed prop-rotors. The necessary disciplinary couplings are all considered within a closed loop optimization process. The procedures involve the consideration of blade aeroelastic, aerodynamic performance, structural and dynamic design requirements. Further, since the design involves consideration of several different objectives, multiobjective function formulation techniques are developed.

Chattopadhyay, Aditi↗