Search NASA⌕ Search

SEARCH · Search NASA

Results for “projection method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Assessment of three dead detector correction methods for cone-beam computed tomography

Purpose: Dead detectors due to manufacturing defects or radiation damage in the electronic portal imaging devices (EPIDs) used for cone-beam computed tomography (CBCT) can lead to image degradation and ring artifacts. In this work three dead detector correction methods were assessed using megavoltage CBCT (MVCBCT) as a test system, with the goals of assessing the relative effectiveness of the three methods and establishing the conditions for which they fail. Methods: MVCBCT projections acquired with four linacs at 8 and 60 MU (monitor units) were degraded with varying percentages (2%-95%) of randomly distributed dead single detectors (RDSs), randomly distributed dead detector clusters (RDCs) of 2 mm diameter, and nonrandomly distributed dead detector disks (NRDDs) of varying diameter (4-16 mm). Correction algorithms were bidirectional linear interpolation (BLI), quad-directional linear interpolation (QLI), and a Laplacian solution (LS) method. Correction method failure was defined to occur if ring artifacts were present in the reconstructed phantom images from any linac or if the modulation transfer function (MTF) for any linac dropped below baseline with a p value, calculated with the two sample t test, of less than 0.01. Results: All correction methods failed at the same or lower RDC/RDS percentages and NRDD diameters for the 60 MU as for the 8 MU cases. The LS method tended to outperform or match the BLI and QLI methods. If ring artifacts anywhere in the images were considered unacceptable, the LS method failed for 60 MU at >33% RDS, >2% RDC, and >4 mm NRDD. If ring artifacts within 4 mm longitudinally of the phantom section interfaces were considered acceptable, the LS method failed for 60 MU at >90% RDS, >80% RDC, and >4 mm NRDD. LS failed due to MTF drop for 60 MU at >50% RDS, >25% RDC, and >4 mm NRDD. Conclusions: The LS method is superior to the BLI and QLI methods, and correction algorithm effectiveness decreases as imaging dose increases. All correction methods failed first due to ring artifacts and second due to MTF drop. If ring artifacts in axial slices within a 4 mm longitudinal distance from phantom section interfaces are acceptable, statistically significant loss in spatial resolution does not occur until over 25% of the EPID is covered in randomly distributed dead detectors, or NRDDs of 4 mm diameter are present.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Study on Evaluation of Project Management Data for Decommissioning of Uranium Refining and Conversion Plant - 12234

Some of nuclear facilities that would no longer be required have been decommissioned in JAEA (Japan Atomic Energy Agency). A lot of nuclear facilities have to be decommissioned in JAEA in near future. To implement decommissioning of nuclear facilities, it was important to make a rational decommissioning plan. Therefore, project management data evaluation system for dismantling activities (PRODIA code) has been developed, and will be useful for making a detailed decommissioning plan for an object facility. Dismantling of dry conversion facility in the uranium refining and conversion plant (URCP) at Ningyo-toge began in 2008. During dismantling activities, project management data such as manpower and amount of waste generation have been collected. Such collected project management data has been evaluated and used to establish a calculation formula to calculate manpower for dismantling equipment of chemical process and calculate manpower for using a green house (GH) which was a temporary structure for preventing the spread of contaminants during dismantling. In the calculation formula to calculate project management data related to dismantling of equipment, the relation of dismantling manpower to each piece of equipment was evaluated. Furthermore, the relation of dismantling manpower to each chemical process was evaluated. The results showed promise for evaluating dismantling manpower with respect to each chemical process. In the calculation formula to calculate project management data related to use of the GH, relations of GH installation manpower and removal manpower to GH footprint were evaluated. Furthermore, the calculation formula for secondary waste generation was established. In this study, project management data related to dismantling of equipment and use of the GH were evaluated and analyzed. The project management data, manpower for dismantling of equipment, manpower for installation and removal of GH, and secondary waste generation from GH were considered. Establishment of the calculation formula for dismantling of each kind of equipment makes it possible to evaluate manpower for dismantling the whole facility. However, it is not easy to prepare calculation formula for all kinds of equipment that exist in the facility. Therefore, a simpler evaluation method was considered to calculate manpower based on facility characteristics. The results showed promise for evaluating dismantling manpower with respect to each chemical process. For dismantling of contaminated equipment, a GH has been used for protection of the spread of contamination. The use of a GH increases manpower for installation and removal of GH etc. Moreover, structural materials of the GH such as plastic sheets, adhesive tape become a burnable secondary waste. To create an effective dismantling plan, it is necessary to carefully consider use of a GH preliminarily. Thus, an evaluation method of project management data such as manpower and secondary waste generation was considered. The results showed promise for evaluating project management data of GH by using established calculation formula. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Droning on to Delivery: Examining the Energy Impacts of Using Drones for Moving Goods

The demand for fast, localized delivery has grown significantly in recent years. Whether for cheesy snacks, prepared food, medical solutions, or business deliveries, fast and efficient delivery is increasingly a demand and differentiator. Drone delivery in the freight sector offers to revolutionize last-mile logistics and improve services. This research analyzes the impacts of drone energy for delivery operations, aiming to compare various types of drones (large and small, rotary and VTOL) and various types of business methods. The project executes novel open-air and laboratory-based testing to look at the impacts of weights, operations, temperatures and weather conditions. The study combines this real-world experimental data with fleet optimization mathematical models to assess energy consumption of different scenarios as well as examine the minimum fleet size and additional battery requirements. These fleet optimization models compare energy between types of deployments with existing delivery methods. The model was also extended to look at mixed fleets of aerial drones and ground vehicles to accommodate different restrictions on drones or when weather prohibits their use. The analysis provided insights into factors such as drone design, payload weight, flight distance, weather conditions and operational parameters and impacts of each. It showed how to combine different types of vehicles to reduce energy and improve services. And it showed that drone speed, routing restrictions, and unfavorable weather significantly influence energy consumption. Our open experiment data and optimization models can assist stakeholders and industry in understanding drone package delivery and offers keys to improving deployment.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Predicting and Controlling Corrosion (Abbreviated Final Report)

Corrosion accumulates significant replacement costs in the transportation, utility, manufacturing, and infrastructure sectors. It also underpins several of LLNL’s core missions in stockpile stewardship, defense, and energy security. Whereas most corrosion and aging models are empirically parameterized to describe well-defined conditions late in the reaction, the factors that determine the early stages of corrosion—during which mitigation could be most impactful— are poorly understood. This project addressed the critical need for new approaches to predict the kinetics of corrosion initiation based on firm physical and chemical understanding. The activities encompassed degradation of relevant metals in both hydrogen-rich and environmental corrosion scenarios. The team integrated state-of-the-art multiscale simulation, in situ characterization, and data science within three technical thrusts: hydriding of Ti alloys; aqueous corrosion of Al and Ni-Cr alloys; and degradation of additively manufactured 316L stainless steel. In each case, novel capabilities were developed to identify and track the impacts of key atomistic, compositional, and microstructural features on the metal systems. For hydriding, protocols were developed to tightly integrate multiscale models, advanced multimodal characterization, and machine learning to determine how hydrogen interacts with native passivating surface oxides and nucleates new undesired phases, shedding new light on the critical role of grain boundaries, interfaces, and atomically disordered regions. For aqueous corrosion, the project demonstrated methods to predict dissolution rates of metal surfaces in corrosive solutions, to measure and understand microstructural and grain orientation effects on corrosion susceptibility, and to investigate competing growth and dissolution kinetics of surface oxides. For additively manufactured metals, analysis using state-of-the-art microscopy techniques revealed the role of specific heterogeneities invoked during laser processing, including cellular structure, dislocations, and precipitates, on corrosion susceptibility. In addition to new capabilities and understanding, the project provided an avenue for workforce development, as well as key partnerships with stakeholders in corrosion science.

08 HYDROGEN↗

Report on Non-Contact DC Electric Field Sensors

This document reports on methods used to measure DC electrostatic fields in the range of 100 to 4000 V/m using a non-contact method. The project for which this report is written requires this capability. Non-contact measurements of DC fields is complicated by the effect of the accumulation of random space-charges near the sensors which interfere with the measurement of the field-of-interest and consequently, many forms of field measurements are either limited to AC measurements or use oscillating devices to create pseudo-AC fields. The intent of this document is to report on methods discussed in the literature for non-contact measurement of DC fields. Electric field meters report either the electric field expressed in volts per distance or the voltage measured with respect to a ground reference. Common commercial applications for measuring static (DC) electric fields include measurement of surface charge on materials near electronic equipment to prevent arcing which can destroy sensitive electronic components, measurement of the potential for lightning to strike buildings or other exposed assets, measurement of the electric fields under power lines to investigate potential health risks from exposure to EM fields and measurement of fields emanating from the brain for brain diagnostic purposes. Companies that make electric field sensors include Trek (Medina, NY), MKS Instruments, Boltek, Campbell Systems, Mission Instruments, Monroe Electronics, AlphaLab, Inc. and others. In addition to commercial vendors, there are research activities continuing in the MEMS and optical arenas to make compact devices using the principles applied to the larger commercial sensors.

42 ENGINEERING↗

Prospects for atomic resolution in-line holography for a 3D determination of atomic structures from single projections

Abstract It is now established that the 3D structure of homogeneous nanocrystals can be recovered from in-line hologram of single projections. The method builds on a quantitative contrast interpretation of electron exit wave functions. Since simulated exit wave functions of single and bilayers of graphene reveal the atomic structure of carbon-based materials with sufficient resolution, we explore theoretically how the approach can be expanded beyond periodic carbon-based materials to include non-periodic molecular structures. We show here theoretically that the 3D atomic structure of randomly oriented oleic acid molecules can be recovered from a single projection.

3D molecular imaging↗

Bayesian weighting of climate models based on climate sensitivity

Using climate model ensembles containing members that exhibit very high climate sensitivities to increasing CO 2 concentrations can result in biased projections. Various methods have been proposed to ameliorate this ‘hot model’ problem, such as model emulators or model culling. Here, we utilize Bayesian Model Averaging as a framework to address this problem without resorting to outright rejection of models from the ensemble. Taking advantage of multiple lines of evidence used to construct the best estimate of the earth’s climate sensitivity, the Bayesian Model Averaging framework produces an unbiased posterior probability distribution of model weights. The updated multi-model ensemble projects end-of-century global mean surface temperature increases of 2 °C for a low emissions scenario (SSP1-2.6) and 5 °C for a high emissions scenario (SSP5-8.5). These estimates are lower than those produced using a simple multi-model mean for the CMIP6 ensemble. The results are also similar to results from a model culling approach, but retain some weight on low-probability models, allowing for consideration of the possibility that the true value could lie at the extremes of the assessed distribution. Our results showcase Bayesian Model Averaging as a path forward to project future climate change that is commensurate with the available scientific evidence.

59 BASIC BIOLOGICAL SCIENCES↗

Bulk viscosity and relaxation time of causal dissipative relativistic fluid dynamics

The microscopic formulas of the bulk viscosity {zeta} and the corresponding relaxation time {tau}{sub {Pi}} in causal dissipative relativistic fluid dynamics are derived by using the projection operator method. In applying these formulas to the pionic fluid, we find that the renormalizable energy-momentum tensor should be employed to obtain consistent results. In the leading-order approximation in the chiral perturbation theory, the relaxation time is enhanced near the QCD phase transition, and {tau}{sub {Pi}} and {zeta} are related as {tau}{sub {Pi}={zeta}}/[{beta}{l_brace}(1/3-c{sub s}{sup 2})({epsilon}+P)-2({epsilon}-3P)/9{r_brace}], where {epsilon}, P, and c{sub s} are the energy density, pressure, and velocity of sound, respectively. The predicted {zeta} and {tau}{sub {Pi}} should satisfy the so-called causality condition. We compare our result with the results of the kinetic calculation by Israel and Stewart and the string theory, and confirm that all three approaches are consistent with the causality condition.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Electrical properties of tin-doped zinc oxide nanostructures doped at different dopant concentrations

This project has been focused on the electrical and optical properties respectively on the effect of Tin doped zinc oxide (ZnO) thin films at different dopant concentrations. These thin films were doped with different Sn dopant concentrations at 1 at%, 2 at%, 3 at%, 4 at% and 5 at% was selected as the parameter to optimize the thin films quality while the annealing temperature is fixed 500 °C. Sn doped ZnO solutions were deposited onto the glass substrates using sol-gel spin coating method. This project was involved with three phases, which are thin films preparation, deposition and characterization. The thin films were characterized using Current Voltage (I-V) measurement and ultraviolet-visible-near-infrared (UV-vis-NIR) spectrophotometer (Perkin Elmer Lambda 750) for electrical properties and optical properties. The electrical properties show that the resistivity is the lowest at 4 at% Sn doping concentration with the value 3.08 × 10{sup 3} Ωcm{sup −1}. The absorption coefficient spectrum obtained shows all films exhibit very low absorption in the visible (400-800 nm) and near infrared (NIR) (>800 nm) range but exhibit high absorption in the UV range.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Area-Preserving Mapping of 3D Carotid Ultrasound Images Using Density-Equalizing Reference Map

Carotid atherosclerosis is a focal disease at the bifurcations of the carotid artery. To quantitatively monitor the local changes in the vessel-wall-plus-plaque thickness (VWT) and compare the VWT distributions for different patients or for the same patients at different ultrasound scanning sessions, a mapping technique is required to adjust for the geometric variability of different carotid artery models. In this work, we propose a novel method called density-equalizing reference map (DERM) for mapping 3D carotid surfaces to a standardized 2D carotid template, with an emphasis on preserving the local geometry of the carotid surface by minimizing the local area distortion. The initial map was generated by a previously described arc-length scaling (ALS) mapping method, which projects a 3D carotid surface onto a 2D non-convex L-shaped domain. A smooth and area-preserving flattened map was subsequently constructed by deforming the ALS map using the proposed algorithm that combines the density-equalizing map and the reference map techniques. This combination allows, for the first time, one-to-one mapping from a 3D surface to a standardized non-convex planar domain in an area-preserving manner. Evaluations using 20 carotid surface models show that the proposed method reduced the area distortion of the flattening maps by over 80% as compared to the ALS mapping method.

60 APPLIED LIFE SCIENCES↗

Passive Noise Analysis for Advanced Tamper Indication. End of Year Report 2015

Idaho National Laboratory (INL) is part of a multi-lab project assessing front-end electronics for unattended measurement (FEUM) being developed for the International Atomic Energy Agency (IAEA) unattended systems. The FEUM development activity provides an opportunity to address tampering detection between FEUM and the detector, signal integrity from FEUM to the data acquisition systems, and data validity – long-standing challenges for the IAEA. This report summarizes the INL activities in Fiscal Year (FY) 2015 to characterize and test passive noise analysis as a potential tamper-indicating approach for implementation into FEUM or as a stand-alone method. The project’s primary objectives in FY-15 were to (1) determine detectable tamper scenarios using four pre-amplifier/detector systems, (2) perform tests of tampering scenarios with three common cable types used by the IAEA, (3) separate radio-frequency-induced events from inherent effect by means of an anechoic chamber, and (4) perform tests at an industrial facility. General conclusions were reached in several areas.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Reflection spectra of NaClO{sub 3}, NaBrO{sub 3}, and LiIO{sub 3} gyrotropic crystals in the vacuum UV region

The reflection spectra in the fundamental-absorption region, 5-25 eV (250-40 nm), of optically active crystals with cubic symmetry (NaClO{sub 3}, NaBrO{sub 3}) and uniaxial optically active crystal (LiIO{sub 3}) have been investigated. It is shown that the reflection spectra of cubic crystals have a similar structure, which is determined by the electronic transitions in the XO{sub 3} group. The comparison of these spectra with the corresponding spectrum of lithium iodide made it possible to determine the type of transition in the spectra of cubic crystals. Using the projection operator method, it was shown that the sign of optical rotation of cubic crystals with symmetry T is independent of the screw axis sign. Possible reasons for the unprecedentedy large optical rotation of lithium iodide crystal in the optical axis direction are considered.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

NESSUS/expert and NESSUS/FPI in the Probabilistic Structural Analysis Methods (PSAM) program

The Numerical Evaluation of Stochastic Structures under Stress (NESSUS) is the primary computer code being developed in the NASA Probabilistic Structural Analysis Methods (PSAM) project. It consists of four modules NESSUS/EXPERT, NESSUS/FPI, NESSUS/PRE and NESSUS/FEM. This presentation concentrates on EXPERT and FPI. To provide an effective interface between NESSUS and the user, an expert system module called NESSUS/EXPERT is being developed. That system uses the CLIPS artificial intelligence code developed to NASA-JSC. The code is compatible with FORTRAN, the standard language for codes in PSAM. The user interacts with the CLIPS inference engine, which is linked to the knowledge database. The perturbation database generated by NESSUS/FEM and managed in EXPERT is used to develop the so-called response or performance model in the random variables. Two independent probabilistic methods are available in PSAM for the computation of the probabilistic structural response. These are the Fast Probability Integration (FPI) method and Monte Carlo simulation. FPI is classified as an advanced reliability method and has been developed over the past ten years by researchers addressing the reliability of civil engineering structures. Monte Carlo is a well-established technique for computing probabilities by conducting a number of deterministic analyses with specified input distributional information.

Burnside, O. H.↗

Generalized optical potential for weakly bound nuclei: Two-cluster projectiles

A generalized optical potential for elastic scattering induced by light nuclei is calculated within the Feshbach projection operator method. The model explicitly takes into account the contribution of the projectile breakup continuum treated within a microscopic few-cluster model. In this work, we formulate the model, deriving an explicit expression for the optical potential, and demonstrate the ability of the model by applying it to deuteron elastic scattering.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Alternate Methods for Eluting Cesium from Spherical Resorcinol-Formaldehyde Resin

A small-column ion exchange (SCIX) system has been proposed for removing cesium from the supernate and dissolved salt solutions in the high-level-waste tanks at the Savannah River Site (SRS). The SCIX system could use either crystalline silicotitanate (CST), an inorganic, non-regenerable sorbent, or spherical resorcinol-formaldehyde (RF), a new regenerable resin, to remove cesium from the waste solutions. The baseline method for eluting the cesium from the RF resin uses 15 bed volumes (BV) of 0.5 M nitric acid (HNO{sub 3}). The nitric acid eluate, containing the radioactive cesium, would be combined with the sludge from the waste tanks and would be converted into glass at the Defense Waste Processing Facility (DWPF) at SRS. The amount of nitric acid that would be used to elute the RF resin, using the current elution protocol, exceeds the capacity of DWPF to destroy the nitrate ions and maintain the required chemical reducing environment in the glass melt. Installing a denitration evaporator at SRS is technically feasible but would add considerable cost to the project. Alternate methods for eluting the resin have been tested, including using lower concentrations of nitric acid, other acids, and changing the flow regimes. About 4 BV of 0.5 M HNO{sub 3} are required to remove the sodium (titrate the resin) and most of the cesium from the resin, so the bulk of the acid used for the baseline elution method removes a very small quantity of cesium from the resin. A summary of the elution methods that have been tested are listed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Detection of atmospheric rivers with inline uncertainty quantification: TECA-BARD v1.0.1

It has become increasingly common for researchers to utilize methods that identify weather features in climate models. There is an increasing recognition that the uncertainty associated with choice of detection method may affect our scientific understanding. For example, results from the Atmospheric River Tracking Method Intercomparison Project (ARTMIP) indicate that there are a broad range of plausible atmospheric river (AR) detectors and that scientific results can depend on the algorithm used. There are similar examples from the literature on extratropical cyclones and tropical cyclones. It is therefore imperative to develop detection techniques that explicitly quantify the uncertainty associated with the detection of events. We seek to answer the following question: given a “plausible” AR detector, how does uncertainty in the detector quantitatively impact scientific results? We develop a large dataset of global AR counts, manually identified by a set of eight researchers with expertise in atmospheric science, which we use to constrain parameters in a novel AR detection method. We use a Bayesian framework to sample from the set of AR detector parameters that yield AR counts similar to the expert database of AR counts; this yields a set of “plausible” AR detectors from which we can assess quantitative uncertainty. This probabilistic AR detector has been implemented in the Toolkit for Extreme Climate Analysis (TECA), which allows for efficient processing of petabyte-scale datasets. We apply the TECA Bayesian AR Detector, TECA-BARD v1.0.1, to the MERRA-2 reanalysis and show that the sign of the correlation between global AR count and El Niño–Southern Oscillation depends on the set of parameters used.

54 ENVIRONMENTAL SCIENCES↗

Convergence analysis of Anderson-type acceleration of Richardson's iteration

We consider here Anderson extrapolation to accelerate the (stationary) Richardson iterative method for sparse linear systems. Using an Anderson mixing at periodic intervals, we assess how this benefits convergence to a prescribed accuracy. The method, named alternating Anderson–Richardson, has appealing properties for high-performance computing, such as the potential to reduce communication and storage in comparison to more conventional linear solvers. We establish sufficient conditions for convergence, and we evaluate the performance of this technique in combination with various preconditioners through numerical examples. Furthermore, we propose an augmented version of this technique.

97 MATHEMATICS AND COMPUTING↗