Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29

Generation of Fullspan Leading-Edge 3D Ice Shapes for Swept-Wing Aerodynamic Testing

The deleterious effect of ice accretion on aircraft is often assessed through dry-air flight and wind tunnel testing with artificial ice shapes. This paper describes a method to create fullspan swept-wing artificial ice shapes from partial span ice segments acquired in the NASA Glenn Icing Reserch Tunnel for aerodynamic wind-tunnel testing. Full-scale ice accretion segments were laser scanned from the Inboard, Midspan, and Outboard wing station models of the 65% scale Common Research Model (CRM65) aircraft configuration. These were interpolated and extrapolated using a weighted averaging method to generate fullspan ice shapes from the root to the tip of the CRM65 wing. The results showed that this interpolation method was able to preserve many of the highly three dimensional features typically found on swept-wing ice accretions. The interpolated fullspan ice shapes were then scaled to fit the leading edge of a 8.9% scale version of the CRM65 wing for aerodynamic wind-tunnel testing. Reduced fidelity versions of the fullspan ice shapes were also created where most of the local three-dimensional features were removed. The fullspan artificial ice shapes and the reduced fidelity versions were manufactured using stereolithography.

Icing↗

Bennu Shape Model Validation Methods and Results

The OSIRIS-REx Independent Shape Modeling Team, staffed by the Jet Propulsion Laboratory (JPL), has used stereophotoclinometry (SPC) to produce a three-dimensional shape model of Bennu. The SPC process is informed by (but is separate from) orbit determination, so it is important to ensure that the resulting shape model is consistent with all available spacecraft tracking data. Specifically, checking the shape model’s consistency with LIDAR measurements can illuminate any discrepancies, because LIDAR measurements are highly correlated with the shape model. This study focuses on the JPL experience with these LIDAR measurements and the greater context of the shape model validation process.

Lauretta, Dante S.↗

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models.

Icing↗

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models

Icing , Simulation, Validation↗

Comparison of Bimodal Ice Shapes on Full-Chord and Hybrid CRM Midspan Models

An ice shape database has been created to document ice accretions on a full-chord length and hybrid versions of a 65 percent scale size of the mid-span section of the Common Research Model resulting from an exposure to a Super-cooled Large Drop (SLD) icing cloud with a bimodal drop size distribution. The ice shapes created were documented with photographs, laser scanned surface measurements over a section of the model span, and measurement of the ice mass over the same section of each ice accretion. Drop distribution effects were evaluated by using the same IRT icing conditions except with either monomodal or bimodal drop distributions. Ice shapes resulting from the bimodal distribution as well as from monomodal distributions of identical cloud droplet Median Volume Diameter (MVD) were obtained and compared. Results indicated that the ice shapes resulting from the monomodal and bimodal drop size distributions have similar 2D Maximum Combined Cross Section, or MCCS, ice shape around the model leading edge region and equivalent ice mass measurement per unit span to within the IRT SLD cloud calibration uncertainty, as expected with this approach, but the bimodal distributions have distinctly larger ice feathers that extended further back on the chord of the model. For most test conditions, the overall size and shape of the main ice accretions compared well between the full-chord and hybrid models.

Icing↗

Modeling the Influence of Moulin Shape on Subglacial Hydrology

Subglacial models represent moulins as cylinders or cones, but field observations suggest that the upper part of moulins in the Greenland Ice Sheet has more complex shapes. These more complex shapes should cause englacial water storage within moulins to vary as a function of depth, a relationship not currently accounted for in models. Here, we use a coupled englacial-subglacial channel model to explore how moulin shape affects depth-dependent moulin water storage and water pressure dynamics within a subglacial channel. We simulate seven different moulin shapes across a range of moulin sizes. We find that the englacial storage capacity at the water level is the main control over the daily water level oscillation range and that depth-varying changes in englacial water storage control the temporal shape of this oscillation. Further, the cross-sectional area of the moulin within the daily oscillation range, but not above or below this range, controls pressures within the connected subglacial channel. Specifically, large cross-sectional areas can dampen daily to weekly oscillations that occur in the surface meltwater supply. Our findings suggest that further knowledge of the shape of moulins around the equilibrium water level would improve englacial storage parameterization in subglacial hydrological models and aid predictions of hydrodynamic coupling.

Moulin↗

Performance Evaluation of a Shaped Sonic Boom Detector and Classifier

NASA will soon fly the X‑59 aircraft over selected communities to evaluate community responses to shaped sonic booms. Community tests will include dozens of deployed acoustic sensors capable of measuring and detecting shaped sonic boom waveforms in situ for rapid onboard analysis. To this end, we present a sonic boom detector and classifier. The sonic boom detector identifies a shaped sonic boom within a measured acoustical waveform by calculating the cross-correlation with a template shaped sonic boom waveform. The sonic boom classifier determines whether the identified event is indeed a shaped sonic boom based on the correlation coefficient and the calculated noise exposure level. We evaluate these algorithms using simulations of on- and off-design X-59 sonic boom waveforms injected into previously measured 30 s ambient noise recordings. Results of this case study indicate that the detector identifies a sonic boom with an accuracy of ±100 ms in 99.98% of the cases. Furthermore, for a given 30 s measurement, the classifier shows true-positive rates of approximately 0.9999 when the false-positive rate is 10e-3. The case study demonstrates that the recommended onboard sonic boom detector and classifier should be highly capable of identifying shaped sonic booms.

sonic boom↗

Additional Comparison of Ice Shapes on Full-Chord and Truncated Swept Wing Models from January 2022

A research program was conducted to evaluate the effectiveness of icing tunnel hybrid model design. A hybrid design is where the full-scale leading edge of a wing section is maintained only to a certain percentage of the local chord, while the aft section of the model is redesigned into a shortened or truncated planform. An initial study was conducted in 2020 where the ice shape geometries on a full-chord length version of the swept CRM65 wing model were compared to those from the hybrid version of CRM65 that were obtained in the NASA Icing Research Tunnel in 2015. The results were reported in a 2021 paper. For most test conditions, the overall size and shape of the ice shapes compared well. However, the ice shapes from the full-chord model were generally slightly smaller than those from the hybrid model. A follow-on test was conducted in 2022 and obtained ice shapes on both full-chord and hybrid wing models during the same test campaign to eliminate the differences in the tunnel spray nozzle configuration and calibration as a cause for the differences observed during the previous investigation. The ice shapes obtained on the full-chord model compared much better to those obtained on the hybrid model during the 2022 test, with nearly identical cross sections and ice mass values generally within 5%.

Icing↗

Additional Comparison of Ice Shapes on Full-Chord and Truncated Swept Wing Models from January 2022

A research program was conducted to evaluate the effectiveness of icing tunnel hybrid model design. A hybrid design is where the full-scale leading edge of a wing section is maintained only to a certain percentage of the local chord, while the aft section of the model is redesigned into a shortened or truncated planform. An initial study was conducted in 2020 where the ice shape geometries on a full-chord length version of the swept CRM65 wing model were compared to those from the hybrid version of CRM65 that were obtained in NASA Icing Research Tunnel in 2015. The results were reported in a 2021 paper. For most test conditions, the overall size and shape of the ice shapes compared well. However, the ice shapes from the full-chord model were generally slightly smaller than those from the hybrid model. A follow-on test was conducted in 2022 and obtained ice shapes on both full-chord and hybrid wing models during the same test campaign to eliminate the differences in the tunnel configuration as a cause for the differences observed during the previous investigation. The ice shapes obtained on the full-chord model compared much better to those obtained on the hybrid model during the 2022 test, with nearly identical cross sections and ice mass values generally within 5%.

Icing↗

V-shaped resonators for addition of broad-area laser diode arrays

A system and method for addition of broad-area semiconductor laser diode arrays are described. The system can include an array of laser diodes, a V-shaped external cavity, and grating systems to provide feedback for phase-locking of the laser diode array. A V-shaped mirror used to couple the laser diode emissions along two optical paths can be a V-shaped prism mirror, a V-shaped stepped mirror or include multiple V-shaped micro-mirrors. The V-shaped external cavity can be a ring cavity. The system can include an external injection laser to further improve coherence and phase-locking.

47 OTHER INSTRUMENTATION↗

Pulse Shaping in 1D Elastic Waveguides for Shock Testing

Mechanical shock events experienced by electronics systems can be reproduced in the laboratory using Hopkinson bar tests. In these tests a projectile strikes an bar, creating a pulse which travels through the bar into the system. The quality of these tests depends on the closeness of the shape of the incident pulse to the shape specified for the test. This paper introduces a new way to control the shape of the incoming pulse, through the use of elastic metamaterial concepts. Two dispersion-modifying material concepts, phononic crystals, and local resonators, are examined for their wave shaping capabilities in 1D elastic waveguides. They are then evaluated using a transfer matrix method to determine the output wave shape in the time domain. The concepts are then optimized for various pulse shapes, showing that they are most effective when they are tuned to introduce dispersion near the fundamental frequency of the incident wave.

DeLima, Washington↗

Near net shape bulk laminated silicon iron electric steel for improved electrical resistance and low high frequency loss

The invention involves producing discontinuous, flake-shaped particles of a soft magnetic material, coating the flake-shaped particles with an electrically insulating coating, and consolidating the coated flaked-shaped particles to form a soft magnetic bulk shape. The consolidated bulk shape can comprise a layer or a simple or complex 3D magnet part shape, which has a consolidated layered microstructure that includes laminated soft magnetic regions that are substantially encapsulated by an electrical insulating layer to increase the resistivity of soft magnetic material, especially when used in silicon iron magnet parts.

Cui, Jun↗

A multi-level load shape clustering and disaggregation approach to characterize patterns of energy consumption behavior

This study presents representative electrical load shapes, disaggregated to the end-use level, for over 5000 customer clusters across California’s residential, commercial, industrial and agricultural sectors. We developed a novel, multi-level load shape clustering approach for residential and commercial sectors leveraging interval meter data for over 350,000 California utility customers collected as a part of the Phase 4 California Demand Response (DR) Potential Study. The clustering approach allowed us to identify typical consumption patterns and categorize customers based on their daily load shape displayed throughout the year. For example, we were able to identify customers with particular energy technologies such as electric vehicles and rooftop solar, as well as building occupancy types such as restaurants, grocery stores and even unoccupied buildings, based solely on whole-building interval data. We then combined the load shape-based clusters with other customer information including building type, climate, geographical area, total consumption and low-income status, to create a set of customer clusters based on both demographics and usage patterns. Total cluster electricity demand was then disaggregated into a wide variety of end-uses using weather normalization and other publicly available end-use load shape datasets. The resulting disaggregated cluster load shapes will be released in anonymized form as part of the Phase 4 DR Potential Study. They will have wide-ranging applications in energy research and policy analysis, including estimation of energy efficiency (EE) and DR potential on the end-use level, time-dependent valuation of EE savings, building stock modeling, and developing customer targeting strategies for EE and DR programs.

Murthy, Samanvitha↗

Shape memory polymer medical device

A system for removing matter from a conduit. The system includes the steps of passing a transport vehicle and a shape memory polymer material through the conduit, transmitting energy to the shape memory polymer material for moving the shape memory polymer material from a first shape to a second and different shape, and withdrawing the transport vehicle and the shape memory polymer material through the conduit carrying the matter.

47 OTHER INSTRUMENTATION↗

Fractionation of Lignin for Selective Shape Memory Effects at Elevated Temperatures

We report a facile approach to control the shape memory effects and thermomechanical characteristics of a lignin-based multiphase polymer. Solvent fractionation of a syringylpropane-rich technical organosolv lignin resulted in selective lignin structures having excellent thermal stability coupled with high stiffness and melt-flow resistance. The fractionated lignins were reacted with rubber in melt-phase to form partially networked elastomer enabling selective programmability of the material shape either at 70 °C, a temperature that is high enough for rubbery matrix materials, or at an extremely high temperature, 150 °C. Utilizing appropriate functionalities in fractionated lignins, tunable shape fixity with high strain and stress recovery, particularly high-stress tolerance were maintained. Detailed studies of lignin structures and chemistries were correlated to molecular rigidity, morphology, and stress relaxation, as well as shape memory effects of the materials. The fractionation of lignin enabled enrichment of specific lignin properties for efficient shape memory effects that broaden the materials’ application window. Electron microscopy, melt-rheology, dynamic mechanical analysis and ultra-small angle neutron scattering were conducted to establish morphology of acrylonitrile butadiene rubber (NBR)-lignin elastomers from solvent fractionated lignins.

36 MATERIALS SCIENCE↗

Shape-Controlled Synthesis of Pd Nanocrystals inAqueous Solutions

This article provides an overview of recent developments regarding synthesis of Pd nanocrystals with well-controlled shapes in aqueous solutions. In a solution-phase synthesis, the final shape taken by a nanocrystal is determined by the twin structures of seeds and the growth rates of different crystallographic facets. Here, the maneuvering of these factors in an aqueous system to achieve shape control for Pd nanocrystals is discussed. L-ascorbic acid, citric acid, and poly(vinyl pyrrolidone) are tested for manipulating the reduction kinetics, with citric acid and B-ions used as capping agents to selectively promote the formation of {111} and {100} facets, respectively. The distribution of single-crystal versus multiple-twinned seeds can be further manipulated by employing or blocking oxidative etching. The shapes obtained for the Pd nanocrystals include truncated octahedron, icosahedron,octahedron, decahedron, hexagonal and triangular plates, rectangular bar, and cube. The ability to control the shape of Pd nanocrystals provides a great opportunity to systematically investigate their catalytic, electrical, and plasmonic properties.

36 MATERIALS SCIENCE↗

Scaled-Up Fabrication of Thin-Walled ZK60 Tubing using Shear Assisted Processing and Extrusion (ShAPE)

Shear Assisted Processing and Extrusion (ShAPE) has been scaled-up and applied to direct extrusion of thin-walled magnesium tubing. Using ShAPE, billets of ZK60A-T5 were directly extruded into round tubes having an outer diameter of 50.8 mm and wall thickness of 1.52 mm. The severe shearing conditions inherent to ShAPE resulted in microstructural refinement with an average grain size of 3.8μm measured at the midpoint of the tube wall. Tensile testing per ATSM E-8 on specimens oriented parallel to the extrusion direction gave an ultimate tensile strength of 254.4 MPa and elongation of 20.1%. Specimens tested perpendicular to the extrusion direction had an ultimate tensile strength of 297.2 MPa and elongation of 25.0%. Due to material flow effects resulting from the simultaneous linear and rotational shear intrinsic to ShAPE, ram force and electrical power consumption during extrusion were just 40 kN and 11.5 kW respectively. This represents a significant reduction in ram force and power consumption compared to conventional extrusion. As such, there is potential for ShAPE to offer a scalable, lower cost extrusion option with potentially improved bulk mechanical properties.

Direct Extrusion↗

Accuracy of Distance Determination by Range–Intensity Correlation Methods for Nonrectangular Illuminating Pulse Shape

We have analyzed the accuracy of distance determination by range–intensity correlation methods in the case of an arbitrary pulse shape. We show that the absolute error is proportional to the pulse duration τ{sub L}. For a trapezoidal pulse shape, which is a reasonable approximation of the real pulse shape, we obtain an analytical estimate of the extremal error and the distance at which is it realized. The maximum error in the distance obtained in calculations with trapezoidal pulses corresponds to an extremely asymmetric pulse and is a little over 10% of the spatial pulse length τ{sub L}c, where c is the speed of light. Symmetric pulses give an error due to nonrectangularity of the pulse that is smaller by a factor of ~2. Since a trapezoidal shape can qualitatively reproduce the shape of practically any real pulse, probably the trapezoidal pulse model gives an estimate of the highest possible error.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗