Search NASA⌕ Search

SEARCH · Search NASA

Results for “solid rocket motor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Design and performance analysis of solid-propellant rocket motors using a simplified computer program

An analysis and a computer program are presented which represent a compromise between the more sophisticated programs using precise burning geometric relations and the textbook type of solutions. The program requires approximately 900 computer cards including a set of 20 input data cards required for a typical problem. The computer operating time for a single configuration is approximately 1 minute and 30 seconds on the IBM 360 computer. About l minute and l5 seconds of the time is compilation time so that additional configurations input at the same time require approximately 15 seconds each. The program uses approximately 11,000 words on the IBM 360. The program is written in FORTRAN 4 and is readily adaptable for use on a number of different computers: IBM 7044, IBM 7094, and Univac 1108.

Sforzini, R. H.↗
NASA NTRS1974

Studies of exhaust products from solid propellant rocket motors fired in an environmental chamber

Experiments are described in which it was attempted to define the state of HCl when rocket motors using ammonium perchlorate and powdered aluminum filler in the fuel system are fired under various relative humidity conditions. A small, variable load rocket motor was developed so that controlled quantities of exhaust products could be produced in an environmental chamber. A technique is described for distinguishing the difference between HCl existing as a gas or existing as an acid aerosol.

Dawbarn, R.↗
NASA NTRS1975

Feasibility of an advanced thrust termination assembly for a solid propellant rocket motor

A total of 68 quench tests were conducted in a vented bomb assembly (VBA). Designed to simulate full-scale motor operating conditions, this laboratory apparatus uses a 2-inch-diameter, end-burning propellant charge and an insulated disc of consolidated hydrated aluminum sulfate along with the explosive charge necessary to disperse the salt and inject it onto the burning surface. The VBA was constructed to permit variation of motor design parameters of interest; i.e., weight of salt per unit burning surface area, weight of explosive per unit weight of salt, distance from salt surface to burning surface, incidence angle of salt injection, chamber pressure, and burn time. Completely satisfactory salt quenching, without re-ignition, occurred in only two VBA tests. These were accomplished with a quench charge ratio (QCR) of 0.023 lb salt per square inch of burning surface at dispersing charge ratios (DCR) of 13 and 28 lb of salt per lb of explosive. Candidate materials for insulating salt charges from the rocket combustion environment were evaluated in firings of 5-inch-diameter, uncured end-burner motors. A pressed, alumina ceramic fiber material was selected for further evaluation and use in the final demonstration motor.

Source record↗
NASA NTRS1976

Acceleration effects on the performance of solid-propellant rocket motors

Some acceleration effects on rocket performance have been well publicized. The dynamic process, characterized by marked increases in 'localized' burning rate, produces excessive case heating, slag retention, pressure buildup, and/or internal flow alterations. Data are presented illustrating drastic effects at low accelerations for sustainer type propellants and its relevance to several recent failures. Normalized orientation dependence of rate augmentation appears coupled to acceleration level and base burning rate. Effects appear influenced by propellant composition. Predictions using subscale motor data show good agreement with observed performance for ground spin and flight tests. Subscale test methods and results are also discussed.

Lucy, M. H.↗
NASA NTRS1976

Nonlinear effects in thermal stress analysis of a solid propellant rocket motor

Direct characterization procedures were used to determine the relaxation modulus as a function of time, temperature, and state of strain. Using the quasi-elastic method of linearviscoelasticity, these properties were employed in a finite element computer code to analyze a thick-walled, nonlinear viscoelastic cylinder in the state of plane strain bonded to a thin (but stiff) elastic casing and subjected to slow thermal cooling. The viscoelastic solution is then expressed as a sequence of elastic finite element solutions. The strain-dependent character of the relaxation modulus is included by replacing the single relaxation curve used in the linear viscoelastic theory by a family of relaxation functions obtained at various strain levels. These functions may be regarded as a collection of stress histories or responses to specific loads (in this case, step strains) with which the cooldown solution is made to agree by iterations on the modulus and strain level.

Francis, E. C.↗
NASA NTRS1980

Tangential mode combustion instability of solid propellant rocket motors. 2: Pressure, frequency, and burning rate histories

The relationships among excursions of mean chamber pressure, high frequency pressure oscillations and accelerations associated with tangential mode combustion instability are considered. A data reduction procedure was devised to utilize the precise pressure time data as input to a numerical solution of the chamber mass balance relationships. The results indicate that both elevated burning rate induced by the tangential wave motions and variable nozzle blockage due to passage of vortical flow through the nozzle throat must act together to generate the large mean pressure peaks observed in the tests. There is strong correlation between the amplitude of wave motions and the level of mean pressure rise. Evidence for the presence of traveling tangential waves at the time of the D.C. shift was found by use of dual Kistler pressure transducers mounted at the head end of the burner. A very unusual frequency history was found to accompany the high amplitude disturbances. This was consistent from test to test and may represent an additional source of information regarding the complicated flow combustion interactions within the propellant burning zone.

Flandro, G. A.↗
NASA NTRS1988

Navier-Stokes calculation of solid-propellant rocket motor internal flowfields

A comprehensive numerical analysis has been carried out to study the detailed physical and chemical processes involved in the combustion of homogeneous propellant in a rocket motor. The formulation is based on the time-dependent full Navier-Stokes equations, with special attention devoted to the chemical reactions in both gas and condensed phases. The turbulence closure is achieved using both the Baldwin-Lomax algebraic model and a modified k-epsilon two-equation scheme with a low Reynolds number and near-wall treatment. The effects of variable thermodynamic and transport properties are also included. The system of governing equations are solved using a multi-stage Runge-Kutta shceme with the source terms treated implicitly. Preliminary results clearly demonstrate the presence of various combustion regimes in the vicinity of propellant surface. The effects of propellant combustion on the motor internal flowfields are investigated in detail.

Hsieh, Kwang-Chung↗
NASA NTRS1991

Solid rocket propulsion

The solid rocket motor failure database; current programs; and shortfalls of solid rocket propulsion are examined. This presentation is represented by viewgraphs.

Nichols, Ronald L.↗
NASA NTRS1954

Design and Evaluation of a Turbojet Exhaust Simulator, Utilizing a Solid-Propellant Rocket Motor, for use in Free-Flight Aerodynamic Research Models

A method has been developed for modifying a rocket motor so that its exhaust characteristics simulate those of a turbojet engine. The analysis necessary to the design is presented along with tests from which the designs are evaluated. Simulation was found to be best if the exhaust characteristics to be duplicated were those of a turbojet engine at high altitudes and with the afterburner operative.

deMoraes, Carlos A.↗
NASA NTRS2011

Space Shuttle Propulsion System Reliability

This session includes the following sessions: (1) External Tank (ET) System Reliability and Lessons, (2) Space Shuttle Main Engine (SSME), Reliability Validated by a Million Seconds of Testing, (3) Reusable Solid Rocket Motor (RSRM) Reliability via Process Control, and (4) Solid Rocket Booster (SRB) Reliability via Acceptance and Testing.

Welzyn, Ken↗
NASA NTRS2014

Coupled CFD-Thermal Analysis of Erosion Patterns Resulting from Nozzle Wedgeouts on the SRTMV-N2

The objective of this analysis was to study the effects of the erosion patterns from the introduction of nozzle flaws machined into the nozzle of the SRTMV-N2 (Solid Rocket Test Motor V Nozzle 2). The SRTMV-N2 motor was a single segment static subscale solid rocket motor used to further develop the RSRMV (Redesigned Solid Rocket Motor V Segment). Two flaws or "wedgeouts" were placed in the nozzle inlet parallel to the ply angles of that section to study erosion effects. One wedgeout was placed in the nose cap region and the other placed in the inlet ring on the opposite side of the bondline, separated 180 degrees circumferentially. A coupled CFD (Computational Fluid Analysis)-thermal iterative analytical approach was utilized at the wedgeouts to analyze the erosion profile during the burn time. The iterative CFD thermal approach was applied at five second intervals throughout the motor burn. The coupled fluid thermal boundary conditions were derived from a steady state CFD solution at the beginning of the interval. The derived heat fluxes were then applied along the surface and a transient thermal solution was developed to characterize the material response over the specified interval. Eroded profiles of each of the nozzle's wedgeouts and the original contour were created at each of the specified intervals. The final iteration of the erosion profile showed that both wedgeouts were "washedout," indicating that the erosion profile of the wedgeout had rejoined the original eroded contour, leaving no trace of the wedgeouts post fire. This analytical assessment agreed with post-fire observations made of the SRTMV-N2 wedgeouts, which noted a smooth eroded contour.

Ables, Catherine↗