Search NASA⌕ Search

SEARCH · Search NASA

Results for “supercritical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Synthesis of boron-carbide aerogels

We present the synthesis of boron carbide aerogels utilizing nano-boron powder and resorcinol–formaldehyde (RF) organic aerogels as precursors. Monolithic aerogels were fabricated from suspensions of boron nanoparticles and RF via an organic sol-gel process, enabling effective distribution of boron in the gel network. The resulting gels underwent supercritical drying, thermal reduction, and subsequent heat treatment to yield boron carbide aerogels with densities ranging from 37 to 55 mg/cm³. By tuning the boron-to-carbon ratio, heat treatment temperature, and dwell time, surface areas up to 53 m²/g were obtained. X-ray diffraction analysis confirmed the formation of the boron carbide phase and detected the presence of residual carbon within the structure.

Materials science↗
DOE OSTI2021

A Tracer Study on sCO2 Corrosion with Multiple Oxygen-Bearing Impurities

Abstract Several modern power production systems utilize supercritical CO 2 (sCO 2 ), which can contain O 2 and H 2 O as impurities. These impurities may degrade the compatibility of structural alloys through accelerated oxidation. However, it remains unclear which of these impurities plays a bigger role in high-temperature reactions taking place in sCO 2 . In this study, various model and commercial Fe‐ and Ni‐based alloys were exposed in 300 bar sCO 2 at 750 °C to low levels (50 ppm) of O 2 and H 2 O for 1,000 h. 18 O-enriched water was used to enable the identification of the oxygen source in the post-exposure characterization of the samples. However, oxygen from the water did not accumulate in the scale, which consisted of Cr 2 O 3 in the cases where a protective oxide formed. A 2wt.% Ti addition to a Ni-22%Cr model alloy resulted in the formation of thicker oxides in sCO 2 , while a 1wt.% Al addition reduced the scale thickness. A synergistic effect of both Al and Ti additions resulted in an even thicker oxide than what was formed solely by Ti, similar to observations for Ni-based alloy 282.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Two-Phase Flow Mechanisms Controlling CO2 Intrusion into Shaly Caprock

Abstract Geologic carbon storage in deep saline aquifers has emerged as a promising technique to mitigate climate change. CO 2 is buoyant at the storage conditions and tends to float over the resident brine jeopardizing long-term containment goals. Therefore, the caprock sealing capacity is of great importance and requires detailed assessment. We perform supercritical CO 2 injection experiments on shaly caprock samples (intact caprock and fault zone) under representative subsurface conditions. We numerically simulate the experiments, satisfactorily reproducing the observed evolution trends. Simulation results highlight the dynamics of CO 2 flow through the specimens with implications to CO 2 leakage risk assessment in field practices. The large injection-induced overpressure drives CO 2 in free phase into the caprock specimens. However, the relative permeability increase following the drainage path is insufficient to provoke an effective advancement of the free-phase CO 2 . As a result, the bulk CO 2 front becomes almost immobile. This implies that the caprock sealing capacity is unlikely to be compromised by a rapid capillary breakthrough and the injected CO 2 does not penetrate deep into the caprock. In the long term, the intrinsically slow molecular diffusion appears to dominate the migration of CO 2 dissolved into brine. Nonetheless, the inherently tortuous nature of shaly caprock further holds back the diffusive flow, favoring safe underground storage of CO 2 over geological time scales.

58 GEOSCIENCES↗
DOE OSTI2020

Solving Recent Challenges for Wrought Ni-Base Superalloys

This paper reviews the status of technology in design and manufacture of new wrought 21 polycrystalline Ni-base superalloys for critical engineering applications. There is a strong 22 motivation to develop new alloys that are capable of operating at higher temperatures to 23 realise improvements in thermal efficiency, which are necessary to achieve environmental 24 targets for reduced emissions of harmful green-house gases. From the aerospace sector, 25 the development of new powder metallurgy and ingot metallurgy alloys are discussed for 26 disk rotor and static applications. New compositions for powder metallurgy contain about 27 50-55% of gamma prime (γ') strengthening precipitates to ensure components operate 28 successfully at temperatures up to 788°C (1450°F). In contrast, new compositions for ingot 29 metallurgy aim to occupy a design space in temperature capability between Alloy 718 and 30 current powder alloys that are in-service, and show levels of γ' of about 30-44%. The focus 31 in developing these alloys was design for manufacturability. To complement the aerospace 32 developments, a review of work to understand the suitability of candidate alloys for multiple 33 applications in Advanced-Ultra Supercritical (AUSC) power plants has been undertaken by 34 Detrois, Jablonski and Hawk from the National Energy Technology Laboratory. In these 35 power plants, steam temperatures are required to reach 700-760°C. The common thread is 36 to develop alloys that demonstrate a combination of high temperature properties, which are 37 reliant on both the alloy composition and microstructure and can be produced readily at the 38 right price. For the AUSC applications, the emphasis is on high temperature strength, long 39 term creep life, phase stability, oxidation resistance and robust welding for fabrications. 40 Whereas for powder disk rotors in aircraft engines, the priority is enhanced resistance to 41 time dependent crack growth, phase stability and resistance to environmental damage, while 42 extending the current strength levels, which are shown by existing alloys, to higher 43 temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Temperature-Dependence of Corrosion of Ni-Based Superalloys in Hot CO 2 -Rich Gases Containing SO 2 Impurities

Future power plants will require Ni-based superalloys resistant to high-temperature corrosion in CO 2 -rich environments containing impurities. In this work, several commercially available Ni-based alloys (617, 230, 625, 263, 740H) were exposed at 600°C, 650°C, 750°C and 1 atm to 95% CO 2 , 4% H 2 O, 1% O 2 without/with 0.1% SO 2 to simulate compositions expected in a direct-fired supercritical CO 2 power cycle. The results indicate no effect of SO 2 at 750°C, a small negative effect at 650°C, and a large negative effect at 600°C. Alloys exposed at the higher temperatures (650–750°C) formed thin Cr-rich oxide scales, whereas the lowest temperature (600°C) resulted in thicker scales consisting of non-protective oxides and sulfates. Thermodynamic analysis indicates this increased corrosion is associated with a transition in the stable compounds in contact with the gas. Understanding the factors that affect this transition will aid in the selection or design of alloys for future CO 2 -based power systems.

36 MATERIALS SCIENCE↗
DOE OSTI2021

High-Temperature Oxidation of Steels in Direct-Fired CO 2 Power Cycle Environments

We report future direct-fired supercritical CO 2 power cycles require steels resistant to oxidation/corrosion in high-temperature CO 2 environments containing various impurities. Herein we studied the oxidation behavior of 14 candidate steels in a simulated direct-fired CO 2 power cycle environment consisting of 95% CO 2 , 4% H 2 O, 1% O 2 with/without 0.1% SO 2 at 1 atm and 550 °C, 600 °C, 650 °C for up to 2500 hours. Steels with ≥11.5 wt% Cr exhibited at least partial coverage by Cr-rich oxide scales leading to a significant decrease in the oxidation rates in both gases. While SO 2 had little effect on low-Cr steels that formed Fe-rich oxides, it generally worsened performance of high-Cr (> 11.5 wt%) steels by hindering the establishment of a protective Cr-rich oxide. This effect was most pronounced at the lowest temperature of 550 °C, which was attributed to strong preferential adsorption of sulfur-containing species within the oxide at relatively low temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hierarchical 3D Printed Porous Silicones with Porosity Derived from Printed Architecture and Silicone-Shell Microballoons

A method is reported to prepare siloxane microballoons that can be loaded into a direct ink write siloxane ink for 3D printing. The resulting structure is subjected to a solvent removal and supercritical drying process to provide a final printed siloxane having both macroscopic and microscopic porosity. Core-shell particles are generated by an emulsion template and phase separation process. Intra-strand closed-cell porosities can be achieved between 10 and 40 vol% thus facilitating additional compressive strain before lockup. Here short term compression set testing highlights the excellent shape retention properties of these elastomers, which have less than 8% relative compression set under load.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The role of the spatial heterogeneity and correlation length of surface wettability on two-phase flow in a CO 2 -water-rock system

This study characterized and modeled heterogeneous surface wettability in sandstone and investigated the role of spatial heterogeneity and correlation length of surface wettability on relative permeability in a supercritical CO 2 (scCO 2 )-brine-rock system. Understanding the role of wettability heterogeneity on relative permeability is essential to geological CO 2 sequestration, oil and gas recovery, and contaminated groundwater remediation. Although numerous studies have attempted to understand the influences of surface wettability, capillary number (Ca), and viscosity ratio, the role of the spatial variation and correlation length of surface wettability on two-phase flow in three-dimensional (3D) porous media has not been unraveled due to the challenges in the measurement and representation of realistic rock surface wettability. In this work, we conducted in-situ measurements of surface contact angle (CA) in a Bentheimer sandstone after CO 2 flooding using micro-computed tomography (micro-CT), and found that the pore-scale CA distribution on rock surfaces followed a log-normal distribution associated with a spatial correlation length. Based on the statistical information from CT scanning, a Gaussian random field was used to model CA distributions that had desired standard deviations and spatial correlation lengths, which were then adjusted within a certain range of values for sensitivity analyses to study their combined effects on the two-phase flow in the porous medium using the lattice Boltzmann (LB) method. The LB two-phase flow simulation was accelerated using hybrid, multicore parallel computing to overcome the challenges in simulating multiphase flow in a large 3D domain having 800 × 800 × 600 nodes. The simulation results showed that the surface wettability heterogeneity (i.e., standard deviation of CA) had a lesser effect on the relative permeability of the wetting fluid (water) but a more significant impact on the relative permeability of the non-wetting fluid (scCO 2 ). The Corey model was used to fit the LB-simulated relative permeability curves of water and scCO 2 and showed that the variations in the relative permeability curves for both water and scCO 2 increased as the standard deviation and spatial correlation length of CA increased. This study illustrated that the assumption of homogeneous surface wettability may cause errors in multiphase flow simulations. Furthermore, the impacts of both the standard deviation and spatial correlation length of CAs should be accounted for. This is the first study that explored the spatial correlation lengths associated with CA distributions on sandstone surfaces and comprehensively investigated the roles of both spatial variation and correlation length of CA on two-phase flow properties in 3D porous media. The optimized LB multiphase flow model was proved a powerful tool to study the interplays and combined effects of these statistical parameters, which had critical applications in numerous natural and engineering processes that involved multiphase flow in porous media.

58 GEOSCIENCES↗
DOE OSTI2022

The importance of maldistribution matching for thermal performance of compact heat exchangers

Compact heat exchangers have gained increased attention in recent years, particularly in demanding applications where high temperatures, high pressures, and/or high power densities are required. For decades, the heat exchanger (HX) community believes that flow maldistribution is a key factor for HX effectiveness, that is, reducing the degree of flow maldistribution (MALD) can help increase the HX effectiveness. Therefore, significant efforts have been devoted in the past to optimizing the header geometry to minimize flow maldistribution. This work was initially motivated by this, and the original goal was to figure out a HX header design with the lowest maldistribution. However, by systematically constructing a comprehensive maldistribution matrix, the analysis revealed that the HX effectiveness is not actually determined by the MALD, but instead dominated by the degree of maldistribution mismatch (MISM). This conclusion was also theoretically generalized, which indicated that matching of the local heat capacity rate is key for achieving maximum performance. The MISM provides a local means of tracking this information, while the MALD only provides a global approximation of the maldistribution itself. With this new perspective, flow maldistribution needs not necessarily be avoided, but instead matched between two fluid streams, to improve the HX performance. We demonstrated that by carefully designing the header geometry to match the velocity profiles of the two fluids in a 2 MW PCHE with molten salt and supercritical carbon dioxide (sCO2) as the heat transfer fluids, the HX could achieve a higher effectiveness even when the maldistribution increased. Finally, a technoeconomic study using a CSP system as an example revealed that the use of this new HX design paradigm could result in CSP capital cost savings as large as 16.6%.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

A high-performance lung-inspired ceramic 3D-printed heat exchanger for high-temperature energy-efficient systems

The thermal-to-electric conversion efficiency of next-generation supercritical carbon dioxide and concentrated solar power plants is significantly augmented by operating at temperatures exceeding 1000 °C if durable, compact, high-temperature heat exchangers (HXs) are developed. Whereas metal 3D-printed HXs fail to operate under extreme temperature conditions, ceramic 3D-printed HXs are deemed promising candidates for high-temperature, highly oxidizing environments. Ceramic 3D-printed HXs, however, exhibit a high gas permeability issue through hot and cold separating walls due to an excessive non-volatile photopolymer content utilized. Here, in this work, a novel leak-free lung-inspired ceramic 3D-printed HX employing a highly complex heat transfer topology is introduced for high-temperature energy-efficient systems. The high permeability issue of ceramic 3D-printed HXs is fully eliminated through a uniform zinc-based coating. It was determined that the effective thermal conductivity of the sintered ceramic heat exchangers is affected by the coated layer. The high-temperature thermal and hydraulic characteristics of the lung-inspired ceramic 3D-printed HX are comprehensively examined and compared against a millichannel 3D-printed HX module. Experimental results indicated that the lung-inspired 3D-printed ceramic HX significantly outperforms its millichannel counterpart. The lung-inspired HX shows a volume-based power density of 8.2 MW/m3 at a hot-side inlet air temperature of 700°C, a 71 % improvement compared with that of the millichannel HX. More importantly, the higher thermal duty of the lung-inspired 3D-printed HX is realized at a lower normalized pressure drop penalty of 510 Pa/W, 22 % lower than that of the millichannel ceramic HX. This study accelerates the advancement of high-performance ceramic 3D-printed HXs with complex topologies for high-temperature energy-efficient systems and/or corrosive environments.

42 ENGINEERING↗
DOE OSTI2025

Printed circuit primary heat exchanger for power conversion in heat pipe microreactor applications

Here, in the present study, a model was developed for a recuperated air Brayton cycle for heat pipe microreactors, and the effect of the primary heat exchanger type assessed. An annular flow heat exchanger and a printed circuit heat exchanger (PCHE) were evaluated. A sub-sized diffusion bonded, PCHE test specimen was manufactured and tested with nitrogen as the working fluid to validate and improve the PCHE model. A comparison of the thermal cycle efficiency for the Brayton cycle coupled to a heat pipe microreactor using each of the two primary heat exchangers showed competitive performance for both options, with achievable cycle efficiencies of 34 % and 35 % for the annular and printed circuit heat exchangers, respectively. The impact of heat pipe length and additional reheating stages on cycle efficiency was studied. Increasing the heat pipe condenser length from 0.8 to 2.0 m resulted in an increase in cycle efficiency of 3.5 % and 3.2 % for the annular and printed circuit heat exchangers, respectively. The use of additional reheating stages showed a reduction in cycle efficiency since the heat pipe surface area limits the primary heat exchanger size and effectiveness. These results highlight the importance of the primary heat exchanger on the performance of a heat pipe microreactor. Overall, the cycle model, testing, and heat exchanger model showed the potential for the PCHE to improve the economics of a heat pipe microreactor relative to the annular flow heat exchanger, which also opens the possibility to use different heat transfer fluids such as supercritical CO 2 .

PCHE↗
DOE OSTI2020

Crystalline Loading of Lipophilic Coenzyme Q10 Pharmaceuticals within Conjugated Carbon Aerogel Derivatives

Low-density aerogel materials currently are being considered for applications in controlling the rate of release for small-molecule pharmaceuticals in vivo. In particular, silica (SiO2) aerogels are an intriguing platform for controlling both the absolute amount of drug loading, but also the crystalline state of small molecule pharmaceuticals has been shown to affect drug release kinetics. To date, loading silica aerogel materials with crystalline pharmaceuticals typically require dissolving small molecules in a supercritical solvent (i.e., CO2) before drying to recover the aerogel/drug composite. Here we demonstrate a simple and low-cost method for controlling the crystallinity of the model drug coenzyme Q10 (CoQ10) within carbon aerogel materials by rationally controlling the chemical microstructure of the aerogel to exhibit ?-conjugated (sp2) chemical bonding. In particular, both pyrolyzed graphene and nanodiamond aerogels exhibit enhanced intrinsic drug loading capacity and CoQ10 crystallinity over a broad range of sp2 surface-curvature. In contrast, amorphous carbon aerogel materials are observed to load CoQ10 pharmaceuticals with strictly amorphous microstructure.

Lim, Mathew↗
DOE OSTI2021

Carbonation, strength development, and characterization of calcined limestone as a potential construction material

The emergence of the modern Portland cement has led to the downfall of lime as a construction material. Consequentially, its use has been limited to repair and restoration of historical buildings. Yet, its lower calcination temperature (~950 °C) and the ability to gain strength through carbonation implies its potential as a sustainable alternative to cement. In this study, calcined limestone was studied concerning its carbonation and strength development. Superplasticizer, raw limestone, and different carbonation regimes were explored as techniques to improve the composite strength development, a shortfall that hinders its re-adoption. The results indicated that the raw limestone as a partial replacement of the calcined limestone significantly improved the carbonation degree and mechanical properties. The average compressive strength reached 20 MPa under 20% CO{sub 2} due to the formation of an interconnected network of calcite as the dominant carbonation product. Supercritical CO{sub 2}, in contrast, formed disjoint particles or agglomerates of carbonates.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Probing ethane phase changes in bead pack via high-field NMR spectroscopy

Phase equilibria analysis in two-phase systems requires discernment of the individual phases as well as the interfacial region. The phase behavior of fluids in constraint geometries have been studied through several techniques. High-Field Nuclear Magnetic Resonance (HF-NMR) can be used to detect fluid phases, i.e. gas, liquid, or supercritical fluid, in the bulk or under confinement. In solution-state HF-NMR, each phase exhibits a distinct chemical shift that correlates to the phase density. In turn, the emergence of multimodal in NMR spectra reveals the coexistence of multiple phases in fluid systems. Our results for ethane show that HF-NMR can enable tracking phase changes in the bulk, but also in macro-scale (10–100's μm in pore size) porous systems at various pressure and temperature conditions, even when the system us out of equilibrium. Finally, these results creates potential opportunities to investigate phase changes influenced by confinement in porous systems, though additional steps are necessary.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Elucidating the temperature and density dependence of silver chloride hydration numbers in high-temperature water vapor: A first-principles molecular simulation study

Hydration numbers of metal complexes in low-density aqueous solutions are required for developing geochemical models for ore-forming metals and for designing supercritical desalination processes. In this study, we investigate the temperature and density dependence of the hydration numbers of silver chloride at 623 K, 673 K, and 713 K and densities of 10–100 kg/m 3 . Experimental estimates of the hydration number in the literature for AgCl at these conditions are inconclusive and possibly contradictory as to the temperature and density dependence. First-principles molecular simulation presents an attractive alternative to experimental measurements. Specifically, recent work shows that machine-learning-accelerated nested Monte Carlo simulations provide reliable estimates for the hydration numbers of CuCl at 623 K from 10 to 100 kg/m 3 . Using the same technique, we find a monotonic temperature dependence, with the hydration number decreasing slightly with increasing temperature. In addition, the simulation-predicted hydration numbers steadily increase with increasing density. These temperature and density trends are in agreement with certain experimental data sets. Therefore, this work demonstrates how first-principles Monte Carlo simulations assist in resolving discrepancies between experimental data sets. Our simulation results also correctly predict that the hydration number, and thus also the solubility, of AgCl is lower than that of CuCl under the same conditions. Furthermore, the bond length and angle formed between the water complex and AgCl differ from those for CuCl, consistent with the lower solubility of AgCl.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electrochemical reduction of per- and polyfluorinated alkyl substances (PFAS): is it possible? Applying experimental and quantum mechanical insights from the reductive defluorination literature

Remediation of per- and polyfluorinated alkyl substances (PFAS) in global water systems is a critical human and environmental health challenge facing society. PFAS consumption is associated with a litany of adverse health effects, and our knowledge of these dangers is still evolving. Current techniques to remove PFAS from water include adsorption to media (e.g. granular activated carbon, ion-exchange resin), nanofiltration, and reverse osmosis. However, these processes create a concentrated PFAS residual that requires further management. Destructive techniques are therefore needed to detoxify these residuals. Oxidative techniques have garnered the most attention (e.g. supercritical water oxidation, electrochemical oxidation) but are energy intensive and potentially form toxic by-products. As an alternative, several groups have researched advanced reduction processes that form aqueous electrons, but these processes are still chemical and energy intensive (e.g. ultraviolet/SO 3 2− , electron beam). This concise review therefore focuses on whether electrochemical reduction — a chemical-free, modular process — could be technically feasible for PFAS destruction.

King, Jacob F.↗
DOE OSTI2021

Surfactant inhibition mechanisms of carbonate mineral dissolution in shale

Surfactants are common additives to hydraulic fracturing and enhanced oil recovery (EOR) fluids, and are under consideration for amendment to supercritical carbon dioxide for geological carbon sequestration (GCS). The effect of a common anionic surfactant, internal olefin sulfonate (IOS), on mineral dissolution from shale into brine was evaluated. When added to brine at concentrations exceeding the critical micelle concentration (94 mg/L), IOS inhibited carbonate mineral dissolution in an Eagle Ford shale, as well as dissolution of optical quality calcite (the dominant carbonate in the shale). Laser profilometry images provide spatial resolution across > 3 orders of magnitude, and indicate that IOS addition to brine both enhances the formation of new etch pits in calcite, and impedes their further growth. Time-of-flight secondary ion mass spectrometry surface profiles show for the first time that IOS preferentially adsorbs at calcite pit edges versus flat calcite surfaces (i.e., terraces). Surface pressure calculations, sulfur K-edge near edge X-ray absorption fine structure (NEXAFS) spectroscopy results, and density functional theory (DFT) calculations support this observation; the DFT results indicate that the sulfonate head group of the IOS molecule binds strongly to the calcite step site as compared to the terrace site. The S K-edge NEXAFS results indicate that IOS adsorbed more to etched calcite surfaces compared to smooth calcite surfaces. Overall, the results indicate that weak adsorption on flat calcite surfaces (i.e., terraces) disrupts water structure and enhances mass transfer of dissolution, while strong adsorption on calcite pit edges displaces adsorbed water and inhibits further etch pit growth. This work provides the first direct evidence of preferential adsorption of IOS to etched calcite surfaces and links it to macroscopic dissolution kinetics. Finally, this work has implications for surfactant-containing fluids used in hydraulic fracturing, EOR and potentially GCS for subsurface injection into carbonate rich reservoirs.

36 MATERIALS SCIENCE↗