Search NASA⌕ Search

SEARCH · Search NASA

Results for “vehicles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 523 records · Page 29
All sourcesNASA NTRSDOE OSTI
NASA NTRS1964

An Adaptive System for Load Relief and Accurate Control of Launch Vehicles

An adaptive load relief control system for a SATURN type vehicle which significantly reduces aerodynamically induced structural loads without incurring excessive velocity dispersions has been studied. This control system utilizes pendulous accelerometers to measure the angle between the total vehicle acceleration vector and the vehicle body. This measurement is used to fly the vehicle along the nominal trajectory to minimize velocity dispersions. However, if unusually high values of wind velocity are encountered, the system will cause the vehicle to turn into the wind to reduce the lateral structural loads. Results of an anal6g computer study show that the adaptive system can reduce aerodynam3cally induced peak structural loads as much as 50 percent under those encountered using conventional control techniques. relief is used only when required, velocity dispersions are held to a minimum.

ADAPTIVE CONTROL SYSTEM↗
NASA NTRS2012

Fully Self-Contained Vision-Aided Navigation and Landing of a Micro Air Vehicle Independent from External Sensor Inputs

Direct-lift micro air vehicles have important applications in reconnaissance. In order to conduct persistent surveillance in urban environments, it is essential that these systems can perform autonomous landing maneuvers on elevated surfaces that provide high vantage points without the help of any external sensor and with a fully contained on-board software solution. In this paper, we present a micro air vehicle that uses vision feedback from a single down looking camera to navigate autonomously and detect an elevated landing platform as a surrogate for a roof top. Our method requires no special preparation (labels or markers) of the landing location. Rather, leveraging the planar character of urban structure, the landing platform detection system uses a planar homography decomposition to detect landing targets and produce approach waypoints for autonomous landing. The vehicle control algorithm uses a Kalman filter based approach for pose estimation to fuse visual SLAM (PTAM) position estimates with IMU data to correct for high latency SLAM inputs and to increase the position estimate update rate in order to improve control stability. Scale recovery is achieved using inputs from a sonar altimeter. In experimental runs, we demonstrate a real-time implementation running on-board a micro aerial vehicle that is fully self-contained and independent from any external sensor information. With this method, the vehicle is able to search autonomously for a landing location and perform precision landing maneuvers on the detected targets.

autonomous landing↗
NASA NTRS2019

Urban Air Mobility Network and Vehicle Type - Modeling and Assessment

This paper describes exploratory modeling of an on-demand urban air mobility (UAM) network and sizing of vehicles to operate within that network. UAM seeks to improve the movement of goods and people around a metropolitan area by utilizing the airspace for transport. Aircraft sizing and overall network performance results are presented that include comparisons of battery-electric and various hybrid-electric vehicles that are fueled with diesel, jet fuel, compressed natural gas, and liquefied natural gas (LNG). Hybrid-electric propulsion systems consisting of internal combustion engine-generators, turbine-generators, and solid oxide fuel cells are explored. Ultimately, the "performance" of the UAM network over a day for each of the different vehicle types, propulsion systems, and stored energy sources is described in four parameters: 1) the average cost per seat-kilometer, which considers the costs of the energy/fuel, vehicle acquisition, insurance, maintenance, pilot, and battery replacement costs, 2) carbon dioxide emission rates associated with vehicle operations, 3) the average passenger wait time, and 4) the average load factor, i.e., the total number of seats filled with paying passengers divided by the total number of available seats. Results indicate that the "dispatch model," which determines when and where aircraft are flown around the UAM network, is critical in determining the overall network performance. This is due to the often-conflicting desires to allow passengers to depart with minimal wait time while still maintaining a high load factor to reduce operating costs. Additionally, regardless of the dispatch model, hybrid-electric aircraft powered by internal combustion engines fueled with diesel or LNG are consistently the lowest cost per seat-kilometer. Battery-electric and future technology LNG/solid oxide fuel cell aircraft produce the lowest emissions (assuming the California grid) with LNG-fueled internal combustion engine-powered hybrids producing only slightly more carbon dioxide.

Assessment↗
NASA NTRS2020

Enabling Dynamic Vehicle Analyses With Improved Atmospheric Attenuation Models in Glenn Research Center Communication Analysis Suite

To aid in meeting the NASA objective of returning humans to the Moon, the Glenn Research Center’s Communication Analysis Suite was augmented with two distinct capabilities. The first capability added was the vehicle propagator. This allows the addition of dynamic aircraft and ground vehicles around any celestial body within the solar system during an analysis. This functionality interpolates the position and velocity of the vehicle relative to a celestial body at the time steps analyzed using the type of path and either a series of waypoints or a direction and duration of travel. The implications of this new capability include lunar rovers and/or drones, such as Dragonfly, where the vehicle propagator will analyze the communications architecture. The newly created vehicle propagator is now in use in communications studies for the 2024 lunar missions, simulating the movement of lunar rovers across the Moon’s southern pole. The second capability added was the augmentation of the atmospheric attenuation model. The previous model did not have a uniform low-elevation attenuation model due to the trigonometric approximation for path length and the exponential nature of low-elevation scintillation. User-defined weather parameters were also added to the updated atmospheric attenuation model. The previous model solely used tabular data based upon the season and location of the transmitting antenna. Multiple simulations of the same configuration now return different results based on the differing weather parameters. Cognitive communications analysis efforts can use this second capability to generate neural network training data based on differing weather conditions at utilized ground stations, a critical step in allowing neural networks to learn how weather parameters impact communications performance.

vehicle propagation↗
NASA NTRS2020

Recommended Crew Systems Capabilities for a Mars Ascent Vehicle as a Function of Flight Duration

In many human Mars exploration architectures, a Mars Ascent Vehicle (MAV) is used at the end of a surface stay to transport crew from the Martian surface to a waiting in-space transportation vehicle. It is possible for this transportation vehicle to be placed in any of several different Mars orbits, the selection of which drives the flight duration of the MAV from launch to docking and the amount of propellant required on the transportation vehicle to reach the same orbit. This paper identifies existing NASA standards and supplies habitability subject matter expert recommendations for the human habitation capabilities of the MAV as a function of flight duration. Living and working functions that may potentially be carried aboard a MAV are assessed. Flight durations considered include up to 8 hours, 8-24 hours, 1-2 days, 2-3 days, 3-4 days, and 4-7 days, which book end flight durations necessary to reach the transportation vehicle at different possible Mars orbits. This analysis will determine if there are key durations that serve as significant break points in required MAV capability.

MAV↗
NASA NTRSDate not supplied

CFD2030 Grand Challenge: CFD-in-the-Loop Monte Carlo Simulation for Space Vehicle Design

Space vehicle design and certification differs widely from aircraft design relying more on probabilistic approaches than deterministic. Monte Carlo simulation plays an important role in the probabilistic design of space vehicles to ensure robust and reliable operation. Today, Monte Carlo flight simulation requires 1000’s of trajectory simulations that use databases to provide aerosciences models. These databases can be extremely expensive and time consuming to develop. Replacing these databases with unsteady computational fluid dynamics directly in the simulation loop has potential to significantly reduce the time required to analyze space vehicle concepts, improve simulation accuracy, and reduce the cost of space vehicle development. The CFD Vision 2030 Study outlined gaps and roadblocks to meeting the vision described in the study. The geometric, physical, and computational challenges associated with CFD-in-the-loop Monte Carlo simulation for space vehicle design are substantial and serve as an excellent grand challenge to advance the CFD 2030 vision.

CFD2030↗
NASA NTRSDate not supplied

Menagerie: an Automated Approach to Launch Vehicle Design

The Advanced Concepts Office (ACO) at NASA Marshall Space Flight Center (MSFC)has been performing conceptual design of launch vehicles since the Space Transportation System Program. As part of its duties ACO has been tasked with investigating the effects of known and potential threats and opportunities to a myriad of launch vehicle concepts, launch sites, and mission profiles known as the launch space. As the launch space becomes more crowded and busy with launch providers and their vehicles, the legacy method of prescribing each design discipline to a single human Subject Matter Expert (SME) has become infeasible. Rapidly changing launch, economical, and political constraints require rapid evaluation of their effects. While moving into this future of rapid response does require streamlining of data and processes, it does not however lead directly to reinventing the wheel. Flight-validated analysis tools, procedures, and lessons learned can be effectively leveraged to bring the experience from decades of government and commercial flight programs to the new paradigm. In this publication we describe the aggregation of all previous launch vehicle design efforts of ACO into an automated and integrated toolchain called menagerie. The toolchain utilizes a suite of NASA, Air Force Research Lab (AFRL), and ACO-developed tools and processes to evaluate launch vehicle concepts, mission profiles, and trades in a fraction of the time previously required.

launch vehicle↗
NASA NTRS1962

An Investigation of the Effects of the Time Lag Due to Long Transmission Distance upon Remote Control. Phase II - Vehicle Experiments. Phase III - Conclusions

An experimental program is undertaken to define the effects upon remote control of long transmission delays. Investigation centers around remote control of a ground vehicle, which is considered to be a representative remote control task. A series of pursuit tracking tests is performed with transport lags ranging from 0 to 6 seconds between the control and the controlled quantity. Various target speeds are tracked with both velocity and acceleration controls. Two types of tracking are performed in an attempt to bracket the actual vehicle situation. In the first the operator attempts to follow the target with his controlled quantity in real time, using the delayed position and rates as feedback. In the second he attempts to follow the target with the delayed controlled quantity. In addition, tests are performed substituting simple electronic models for the human in an attempt to gain an understanding of human response with time delays in the control loop. A series of tests with an actual vehicle are performed with the intent of relating the tracking tests to the actual situation of interest. Time delays of from 0 to 3 seconds are included in the control loop. Performance is scored at various speeds over both continuous and obstacle courses. Both two and four-wheel steering are investigated. In the experiments the effects of all variables except delay magnitude and target complexity are minimized. Curves are obtained showing performance as a function of time delay and target complexity. These curves are discussed. Correlation of the tracking and vehicle experiments is discussed. Comments are made concerning the design of a minimum control system for a remotely controlled lunar roving vehicle.

REMOTE CONTROL↗
NASA NTRS1965

Development of electrostatic sensors for scout systems evaluation vehicle, 131r

In the course of a Scout vehicle mission, a static charge may build up on the vehicle and reach sufficiently high values to become potentially dangerous to the vehicle mission. The development of electrostatic sensors for monitoring the potential build-up on a Scout vehicle is discussed in this report. The investigation and studies, which produced the theories tor the electrostatic sensor concepts, are also discussed. The sensors were designed, fabricated and installed on Scout vehicle 131R. Results of the sensor development program are discussed in full; however, at the time this report was completed, the flight experiment had not been accomplished.

Scout Project↗
NASA NTRS1970

Performance characteristics of the lifting body vehicle

Designers have relied heavily upon aerodynamic theory and wind-tunnel testing of large and small models to obtain accurate estimates of the performance characteristics for a new configuration and to provide a realistic simulation of the vehicle’s flying characteristics before its first flight, However, the highly unusual shapes of the lifting body vehicles have raised some questions of how accurately their lift and drag characteristics could be defined with these prediction techniques. Thus it is pertinent to com- pare the lift and drag data obtained in flight for three lifting body vehicles (ref. 1 and unpublished results) with wind-tunnel measurements obtained on the actual flight vehicles (refs. 2 and 3 and unpublished results) and on small-scale models of the flight vehicles (ref. 4 and unpublished results). These comparisons, together with discussions of separated flow problems and the effects of ablated surfaces, should be useful to the designers of space shuttlecraft.

Jon S Pyle↗
NASA NTRS1972

Performance estimates for space shuttle vehicles using a hydrogen or a methane fueled turboramjet powered first stage

Two- and three-stage (second stage expendable) shuttle vehicles, both having a hydrogen-fueled, turboramjet-powered first stage, are compared with a two-stage, VTOHL, all-rocket shuttle in terms of payload fraction, inert weight, development cost, operating cost, and total cost. All of the vehicles place 22,680 kilograms of payload into a 500-kilometer orbit. The upper stage(s) uses hydrogen-oxygen rockets. The effect on payload fraction and vehicle inert weight of methane and methane-FLOX as a fuel-propellant combination for the three-stage vehicle is indicated. Compared with a rocket first stage for a two-stage shuttle, an airbreathing first stage results in a higher payload fraction and a lower operating cost, but a higher total cost. The effect on cost of program size and first-stage flyback is indicated. The addition of an expendable rocket second stage (three-stage vehicle) improves the payload fraction but is unattractive economically.

Knip, G., Jr.↗
NASA NTRS1972

Advanced small launch vehicle study

A conceptual design study was conducted to determine the most economical (lowest cost/launch) approach for the development of an advanced small launch vehicle (ASLV) for use over the next decade. The ASLV design objective was to place a 340 kg (750 lb) payload into a 556 km (300 n.mi.) circular orbit when launched due east from Wallops Island, Virginia. The investigation encompassed improvements to the current Scout launch vehicle; use of existing military and NASA launch vehicle stages; and new, optionally staged vehicles. Staging analyses included use of liquid, solid, and hybrid propellants. Improvements in guidance, controls, interstages, telemetry, and payload shroud were also considered. It was concluded that the most economical approach is to progressively improve the Scout launch vehicle in three phased steps which are discussed.

Reins, G. E.↗
NASA NTRS1972

Analysis and design of a capsule landing system and surface vehicle control system for Mars exporation

The problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars were investigated. Problem areas receiving attention include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis; navigation, terrain modeling and path selection; and chemical analysis of specimens. The following specific tasks were studied: vehicle model design, mathematical modeling of dynamic vehicle, experimental vehicle dynamics, obstacle negotiation, electromechanical controls, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer subsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, chromatograph model evaluation and improvement and transport parameter evaluation.

Frederick, D. K.↗
NASA NTRS1972

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

Investigation of problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars has been undertaken. Problem areas receiving attention include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis; terrain modeling and path selection; and chemical analysis of specimens. The following specific tasks have been under study: vehicle model design, mathematical modeling of a dynamic vehicle, experimental vehicle dynamics, obstacle negotiation, electromechanical controls, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer sybsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, chromatograph model evaluation and improvement.

Frederick, D. K.↗
NASA NTRS1973

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

Problems related to the design and control of a mobile planetary vehicle to implement a systematic plan for the exploration of Mars are reported. Problem areas include: vehicle configuration, control, dynamics, systems and propulsion; systems analysis, terrain modeling and path selection; and chemical analysis of specimens. These tasks are summarized: vehicle model design, mathematical model of vehicle dynamics, experimental vehicle dynamics, obstacle negotiation, electrochemical controls, remote control, collapsibility and deployment, construction of a wheel tester, wheel analysis, payload design, system design optimization, effect of design assumptions, accessory optimal design, on-board computer subsystem, laser range measurement, discrete obstacle detection, obstacle detection systems, terrain modeling, path selection system simulation and evaluation, gas chromatograph/mass spectrometer system concepts, and chromatograph model evaluation and improvement.

Frederick, D. K.↗
NASA NTRS1973

Results of tests in the MSFC 14 x 14 inch trisonic wind tunnel on a .004 scale model of the Rockwell International Space Shuttle Vehicle 3, (integrated configuration)

Experimental aerodynamic investigations were conducted during mid-July, 1973 on a .004 scale model of the Rockwell International integrated configuration Space Shuttle Vehicle 3. The purpose of the tests was three fold: (1) to determine the static stability characteristics of the integrated vehicle, utilizing the Vehicle 3 orbiter configuration; (2) to determine the effect of interstage structure and tank external fuel lines on the integrated vehicle aerodynamic characteristics; (3) to determine the effects of the aft interstage structure on orbiter aerodynamic loads. Data were recorded on the integrated vehicle (test no. 579) at angles of attack and sideslip ranging from -10 deg to 10 deg over a Mach number schedule from 0.6 to 4.96. Data were obtained on the orbiter alone in the presence of the external tank with SRB attached (test no. 580) at angles of attack from -10 deg to 10 deg over a Mach number range from .6 to 1.96. Plotted data are presented in the body axis system.

Allen, E. C.↗
NASA NTRS1973

Analysis and design of a capsule landing system and surface vehicle control system for Mars exploration

The following tasks related to the design, construction, and evaluation of a mobile planetary vehicle for unmanned exploration of Mars are discussed: (1) design and construction of a 0.5 scale dynamic vehicle; (2) mathematical modeling of vehicle dynamics; (3) experimental 0.4 scale vehicle dynamics measurements and interpretation; (4) vehicle electro-mechanical control systems; (5) remote control systems; (6) collapsibility and deployment concepts and hardware; (7) design, construction and evaluation of a wheel with increased lateral stiffness, (8) system design optimization; (9) design of an on-board computer; (10) design and construction of a laser range finder; (11) measurement of reflectivity of terrain surfaces; (12) obstacle perception by edge detection; (13) terrain modeling based on gradients; (14) laser scan systems; (15) path selection system simulation and evaluation; (16) gas chromatograph system concepts; (17) experimental chromatograph separation measurements and chromatograph model improvement and evaluation.

Frederick, D. K.↗
NASA NTRS1974

Preliminary performance estimates of an oblique, all-wing, remotely piloted vehicle for air-to-air combat

A computerized aircraft synthesis program has been used to assess the effects of various vehicle and mission parameters on the performance of an oblique, all-wing, remotely piloted vehicle (RPV) for the highly maneuverable, air-to-air combat role. The study mission consists of an outbound cruise, an acceleration phase, a series of subsonic and supersonic turns, and a return cruise. The results are presented in terms of both the required vehicle weight to accomplish this mission and the combat effectiveness as measured by turning and acceleration capability. This report describes the synthesis program, the mission, the vehicle, and results from sensitivity studies. An optimization process has been used to establish the nominal RPV configuration of the oblique, all-wing concept for the specified mission. In comparison to a previously studied conventional wing-body canard design for the same mission, this oblique, all-wing nominal vehicle is lighter in weight and has higher performance.

Nelms, W. P., Jr.↗