Search NASA⌕ Search

SEARCH · Search NASA

Results for “304L”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Strength models for stainless steel 304L alloys

This report provides nominal, weak and strong calibrations of Preston- Tonks-Wallace (PTW) plasticity model [1] parameters for stainless steel 304L alloys. The data sets shown indicate that for these alloys, the material’s prove- nance plays an important role in accurate characterization. First we provide a parameter set fit to compression-tested annealed samples, both quasistatic (QS) and split Hopkinson pressure bar (SHPB), from the MST-8 group at LANL within the last year. Then we compare simulations using the FLAG hydrocode [2], with this and other parameter sets, to data from a Taylor cylinder impact test performed within the same group around 2013.

36 MATERIALS SCIENCE↗
DOE OSTI2022

304L Can Crush Validation Studies

Accurate prediction of ductile behavior of structural alloys up to and including failure is essential in component or system failure assessment, which is necessary for nuclear weapons alteration and life extensions programs of Sandia National Laboratories. Modeling such behavior requires computational capabilities to robustly capture strong nonlinearities (geometric and material), rate- dependent and temperature-dependent properties, and ductile failure mechanisms. This study's objective is to validate numerical simulations of a high-deformation crush of a stainless steel can. The process consists of identifying a suitable can geometry and loading conditions, conducting the laboratory testing, developing a high-quality Sierra/SM simulation, and then drawing comparisons between model and measurement to assess the fitness of the simulation in regards to material model (plasticity), finite element model construction, and failure model. Following previous material model calibration, a J 2 plasticity model with a microstructural BCJ failure model is employed to model the test specimen made of 304L stainless steel. Simulated results are verified and validated through mesh and mass-scaling convergence studies, parameter sensitivity studies, and a comparison to experimental data. The converged mesh and degree of mass-scaling are the mesh discretization with 140,372 elements, and a mass scaling with a target time increment of 1.0e-6 seconds and time step scale factor of 0.5, respectively. Results from the coupled thermal-mechanical explicit dynamic analysis are comparable to the experimental data. Simulated global force vs displacement (F/D) response predicts key points such as yield, ultimate, and kinks of the experimental F/D response. Furthermore, the final deformed shape of the can and field data predicted from the analysis are similar to that of the deformed can, as measured by 3D optical CMM scans and DIC data from the experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comprehensive Characterization of Helium-Induced Degradation of the Friction Stir Weld on Neutron-Irradiated 304L Stainless Steel

The report describes new experimental results on the mechanical performance of the friction stir welds made on neutron-irradiated 304L stainless steel with helium. The report focuses on helium-related issues (e.g., the helium-induced degradation in the welded joint), aiming at the need to repair irradiated components of nuclear power plants. The friction stir welds analyzed here were previously produced at the US Department of Energy’s Oak Ridge National Laboratory, and initial characterization work was performed, mostly addressing the microstructure and if macroscopic cracks and helium bubbles present. The present work attempts to perform a more comprehensive study to assess mechanical performance (i.e., microhardness distribution, tensile properties, tensile deformation behaviors, and fractography analysis).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Stress-strain and work hardening relationships of 304L AM alloy

A new approach to analytically derive constitutive stress-strain relationships from modeling the work hardening behavior of alloys was developed for assessing the strength and ductility of the Ti-6Al-4V alloy. This new approach is now successfully applied for assessing the quasi-static stress-strain behavior of an additively manufactured 304L sample. A predictive capability of this modelling approach may then be extended to model material stress-strain behavior at higher strain rates of loading.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Determination of the Solid-State Resistance-Weldability of Additively Manufactured 304L Stainless Steel

• A scoping study was undertaken at Savannah River National Laboratory (SRNL) to determine the solidstate resistance-weldability of additively manufactured 304L stainless steel. • Additive manufacturing of pressure-containing boundaries is of interest to numerous industries. • The approach investigated in this study was a low energy, solid state spot weld (pinch weld). • This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. • This work aimed to understand the impact of AM on the bond quality and weld geometry of pinch welds.

Rogers, Jeremy K. [Savannah River National Laborat↗
DOE OSTI2022

Evaluation of Applied Stress on Atmospheric Corrosion and Pitting Characteristics in 304L Stainless Steel

For this study, the effects of applied stress, ranging from tensile to compressive, on the atmospheric pitting corrosion behavior of 304L stainless steel (SS304L) were analyzed through accelerated atmospheric laboratory exposures and microelectrochemical cell analysis. After exposing the lateral surface of a SS304L four-point bend specimen to artificial seawater at 50°C and 35% relative humidity for 50 d, pitting characteristics were determined using optical profilometry and scanning electron microscopy. The SS304L microstructure was analyzed using electron backscatter diffraction. Additionally, localized electrochemical measurements were performed on a similar, unexposed, SS304L four-point bend bar to determine the effects of applied stress on corrosion susceptibility. Under the applied loads and the environment tested, the observed pitting characteristics showed no correlation with the applied stress (from 250 MPa to -250 MPa). Pitting depth, surface area, roundness, and distribution were found to be independent of location on the sample or applied stress. The lack of correlation between pitting statistics and applied stress was more likely due to the aggressive exposure environment, with a sea salt loading of 4 g/m 2 chloride. The pitting characteristics observed were instead governed by the available cathode current and salt distribution, which are a function of sea salt loading, as well as pre-existing underlying microstructure. In microelectrochemical cell experiments performed in Cl - environments comparable to the atmospheric exposure and in environments containing orders of magnitude lower Cl - concentrations, effects of the applied stress on corrosion susceptibility were only apparent in open-circuit potential in low Cl - concentration solutions. Cl - concentration governed the current density and transpassive dissolution potential.

36 MATERIALS SCIENCE↗
DOE OSTI2025

DETERMINATION OF THE SOLID-STATE RESISTANCE-WELDABILITY OF ADDITIVELY MANUFACTURED 304L STAINLESS STEEL

Additive manufacturing of pressure-containing boundaries is of interest to numerous industries, so a project was initiated to develop several different methods to join and weld additively manufactured materials. The approach investigated in this study was a low energy, solid state spot weld. This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. Additively manufactured 304L stainless steel sheets, semi-tubes, and tubes were resistance spot welded and compared to comparable welds in conventionally manufactured tubing. Radiographic computed tomography and metallography were used to evaluate the suitability of the welds using three criteria: weld closure length, thickness, and width. All additively manufactured test welds closely matched the conventional tubing for these criteria

additive manufacturing↗
DOE OSTI2021

Complexity of deformation mechanism in neutron-irradiated 304L austenitic stainless steel at microstructural scale

The deformation mechanisms of neutron-irradiated 304 L stainless steel have been investigated using the in-situ electron backscattered diffraction (EBSD) technique. To decipher the role of irradiation, a detailed analysis was performed on irradiated miniature samples and compared with nonirradiated samples. Furthermore, at three levels of engineering strain, —0.0%, 4.8%, and 14.5%—microstructural features as well as EBSD were recorded at the identical location during in-situ deformation testing. Post-mortem analysis of the EBSD data revealed that the neutron-irradiated samples had higher fractions of the slip bands even at low amounts of deformation. Along with the slip bands, the neutron-irradiated sample showed the twins and martensitic phase formed almost parallel to the slip bands. In addition, the image results also indicated that the formation of twins and phases associated with the slip bands. A detailed mechanistic understanding has been investigated to identify the (111)γ planes orientation with respect to the loading direction associated with the formation of twins and martensite. The newly formed deformation twins and martensite were also found to maintain this relationship when they existed together.

304L austenitic stainless steel↗
DOE OSTI2026

Mechanistic transition of stainless steel 304L corrosion in MgCl 2 phase change material under thermal cycling

Magnesium chloride (MgCl 2 )-based molten salt phase change materials (PCMs) are promising candidates for thermal energy storage (TES) owing to their advantageous thermophysical properties, however, their high corrosivity in the molten state limits material compatibility. In this study, the corrosion behavior of 304?L stainless steel (SS304L) exposed to MgCl2 PCM was investigated as a function of thermal cycling (up to 9000 cycles) relevant to PCM-based TES systems. Microstructural changes and elemental redistribution at the alloy-salt interface under thermal cycling conditions were characterized using synchrotron-based X-ray fluorescence (XRF) and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDS). Results show that corrosion is governed by selective Cr-dissolution and elemental diffusion near the interface and grain boundaries. A clear transition in the dominant corrosion mechanism is observed with increasing thermal cycles. Surface corrosion is the dominant mechanism up to 1000 cycles, whereas intergranular corrosion becomes the primary degradation mode beyond 2000 cycles. These mechanistic changes are interpreted in terms of evolving interfacial chemistry, microstructure and the diffusion-driven redistribution of alloying elements.

36 MATERIALS SCIENCE↗