Search NASA⌕ Search

SEARCH · Search NASA

Results for “316 Stainless Steels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Corrosion of 316 SS in direct contact with Zircaloy-4 in repository relevant conditions

The effects of interfacial contact between 316 stainless steel (316 SS) waste canister and spent fuel cladding material (Zircaloy-4) in case of water intrusion into a deep geological repository are investigated. Hydrothermal corrosion experiments of 316 SS and Zircaloy-4 in direct contact were performed at elevated temperatures in MilliQ water and simulated Mont Terri groundwater. Hematite, magnetite, chromite, and baddeleyite form as secondary phases. pH of the Mont Terri solution increases with corrosion duration and magnetite forms preferentially instead of hematite. Thermodynamic modeling shows that iron oxidation in 316 SS controls the pH and redox potential of the aqueous environment and is in good agreement with experimental Mont Terri results, showing that experimental Mont Terri results trend to equilibrium. All oxides except hematite are predicted to exist at thermodynamic equilibrium based on calculations, implying that experimentally formed hematite will be reduced or transformed to magnetite at equilibrium. The thermodynamically predicted chromite was observed to form only at the interface where 316 SS was in contact with Zircaloy-4 at 250°C, showing that contact with Zircaloy-4 seems to accelerate the 316 SS corrosion to thermodynamic equilibrium. Finally, Mont Terri groundwater readily trends towards thermodynamic equilibrium, leading to a pH and redox buffered system that is dominated by iron in solution coming from the accelerated corrosion of 316 SS caused by Zircaloy-4 contact.

316 stainless steel↗
DOE OSTI2024

Dislocation channel broadening–A new mechanism to improve irradiation-assisted stress corrosion cracking resistance of additively manufactured 316 L stainless steel

Additively manufactured (AM) 316 L stainless steel (SS) after hot isostatic pressing (HIP) was found to exhibit superior resistance to irradiation-assisted stress corrosion cracking (IASCC) in high-temperature water, as compared to wrought 316 L SS. The well-accepted IASCC factors of radiation-induced segregation (RIS) and radiation hardening are not accurate descriptions of IASCC susceptibility in this case. A decreased strain localization along grain boundaries, caused by dislocation channel broadening, was confirmed to suppress crack initiation. A unique distribution of irradiation-induced defects in HIP AM 316 L SS eased dislocation cross-slip compared to those in the wrought counterpart, thus increasing the channel width near the grain boundaries. Here for the first time, this study highlights the importance of dislocation channel broadening as a potential mechanism to further improve the IASCC resistance of 316 L SS and provides direct experimental evidence based on commercial-grade materials.

316L stainless steel↗
DOE OSTI2023

Accelerated Materials Design for Molten Salt Technologies Using Innovative High-Throughput Methods

The focus of the project is on building an innovative accelerated materials design platform for molten salt technologies using novel high-throughput methods coupled to data analytics. The main objectives is to predict a FeCrMnNi alloy compositional space with better corrosion resistance than stainless steel 316 and identify new molten salt corrosion mechanisms. The project demonstrates the feasibility to use high-throughput methods coupled to data analytics to accelerate alloy design for extreme environments applications. Using a trained and tested machine learning (ML) model, 2000 FeCrMnNi alloy corrosion rate in molten chloride salts were predicted and a compositional field with corrosion rate lower than 316 stainless steel was identified. The ML model interpretability unveiled multiple features of importance in the model prediction. Some features were expected to be of relative significance, such as work function, surface energy and alloy electronegativity, and the ML model interpretability analysis confirmed those. On the other hand, the most important feature is the diffusion coefficient of Ni in the bulk alloy which indicates that a surface diffusion mechanism plays an important role in the overall corrosion mechanism in molten salts.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tritium Trapping Thermodynamics by Point Defects at Interfacial Fe-Al Phases of the Aluminide Coating

Density functional theory (DFT) simulations have been carried out to evaluate the potential for tritium trapping by metal vacancies in four phases (i.e., (Fe, Cr, Ni), AlFe 3 , NiAl, and AlFe) identified near the interface between the Al coating and 316 stainless steel (316 SS) cladding. In addition, an ab initio thermodynamics approach has been employed to predict the temperature and T 2 -partial pressure dependence on the thermodynamics of tritiated defects. Key results in this work suggest that metal vacancies in the four phases have the potential to favorably trap tritium species. This thermodynamic trend can be correlated to the high energy cost of having an interstitial tritium in the lattice, which has been calculated to be at least 0.48 eV. By combining the results of this study with previous theoretical works investigating tritium behavior in other Fe-Al phases identified in the aluminide coating, suggest that metal vacancies are generally able to trap tritium in various Fe-Al aluminide phases. Especially, it was found that Al vacancies are the most efficient to trap tritium, followed by Fe vacancies, then Ni and Cr vacancies. Strong interactions between tritium and the metal vacancies are occurring by the formation of Fe—T bonds. The formation of Cr—T, Ni—T, or Al—T bonds are found less energetically favorable than Fe—T bonds.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Thermodynamics of Tritium Trapping by Point Defects at Interfacial Cr-based Phases of the Al Coating

Density functional theory (DFT) simulations have been carried out to evaluate the potential for tritium trapping by metal vacancies in four phases Cr-containing phases (i.e., Cr3Si, Al0.3Cr0.7, Al8Cr5-HT, and Al8Cr5) identified near the interface between the Al coating and 316 stainless steel (316 SS) cladding. In addition, an ab initio thermodynamics approach has been employed to predict the temperature and T2-partial pressure dependence on the thermodynamics of singly tritiated defects. Key results in this work suggest that metal vacancies in the four phases have the potential to favorably trap tritium species, especially Si vacancies in Cr3Si phase. This overall thermodynamic trend can be correlated to the energy cost of having an interstitial tritium in the lattice, which has been calculated to range from 0.17 eV in Al8Cr5-HT to 0.89 eV in Cr3Si. A comparison of the results from this study with previous theoretical works investigating tritium behavior in other Fe-Al phases identified in the aluminide coating, suggests that metal vacancies are generally able to trap tritium in various Fe-Al aluminide phases. Especially, it was found that Si and Al vacancies would be the most efficient to trap for tritium, followed by Cr vacancies, then Fe and Ni vacancies. In the four Cr-based material phases investigated in this work, it is interesting to note that, in the absences of Fe or Ni species, strong interactions between tritium and the metal vacancies are always occurring by the formation of preferential Cr—T bonds (i.e., no Si—T or Al—T bonds were formed).

Sassi, Michel J.↗
DOE OSTI2025

Stochastic room temperature creep of 316 L stainless steel

The creep behavior of 316 L stainless steel at room temperature was evaluated as a function of time and applied stress using a new high-throughput approach. Several common creep models were evaluated against the observations, leading to deeper analysis of a stress-dependent modified logarithmic creep model. Within this model, multiple sources of uncertainty were compared. Aleatoric stochastic variation between samples under nominally identical conditions was identified as the primary contributor to uncertainty in creep response. Under any particular set of conditions, the sample-to-sample variability in creep strain was as high as a factor of two, highlighting the engineering importance of characterizing large statistical datasets. The model's extrapolation capabilities were assessed by comparing predictions derived from calibration on partial, shorter-duration subsets of the data. In conclusion, these findings underscore the importance of accounting for stochastic effects in predictive modeling of aging phenomena.

High-throughput↗
DOE OSTI2025

Characterization of in-situ and ex-situ ion-irradiated additively manufactured 316L and 316H stainless steels

Additively manufactured (AM) 316 stainless steel (SS) differs from its wrought counterpart in its unique dislocation cell structure and the presence of segregation and oxide particles at the cell walls. This work investigated the evolution of the microstructure in laser powder bed fusion (LPBF) 316L and 316H SS under in-situ 1 MeV Kr ion irradiation at 600 °C to 5 dpa, and ex-situ 4 MeV Ni ion irradiation at 300 °C and 600 °C from 0.2 dpa to 10 dpa, with a dose rate for all experiments of 10 -3 dpa/s. The results reveal that the dislocation cell structure results in heterogeneous formation of dislocation loops and voids, particularly at 600 °C, where loops tend to form within the cell interiors while voids form at the cell boundaries. LPBF 316H has a reduced level of swelling compared to LPBF 316L due to prolonged incubation. Energy Dispersive X-ray Spectroscopy (EDS) mapping indicates Ni and Si segregation at void surfaces due to radiation-induced segregation. At 300 °C, where voids are absent, the distribution of dislocation loops and stacking fault tetrahedra appears to be uniform. Dislocation cell structures mostly disappeared by 2 dpa for all conditions in this work. M 23 C 6 carbides were observed in LPBF 316H at 600 °C as early as 0.2 dpa, but not in LPBF 316L. Nanoindentation was performed to obtain the hardness of irradiated materials. In conclusion, this work illustrated the influence of additive manufacturing processes on microstructure evolution under irradiation, revealing the differences as well as the similarities as compared with wrought 316 SS, and the AM-related phenomenon that can potentially occur under neutron irradiation in nuclear reactors.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Corrosion of 316 L stainless steel under the natural circulation of molten NaCl-MgCl 2 salt

The corrosion behavior of 316 L stainless steel (SS) was studied via the natural circulation of molten eutectic NaCl-MgCl 2 salt through a microloop. The post-corrosion tested 316 L SS microloop sections were characterized with microscopy techniques to determine the microstructural and microchemical changes that occurred at the alloy/salt interface. It was found that 316 L SS showed heterogeneous dissolution at the hot-leg, whereas deposition of corrosion products occurred at the cold-leg. For the first time, experimentally obtained molten salt flow-induced corrosion of 316 L SS results were combined with computational thermodynamic-kinetic models to validate the dissolution and deposition in terms of elemental compositional changes at the alloy/salt interface. The thermodynamic-kinetic modeling predicted that the heterogeneous dissolution of Cr and Fe from the hot-leg section of 316 L SS persisted throughout the salt circulation. The model also estimated that, despite Cr deposition starting earlier than Fe, the total redeposition of Fe is expected to be significantly greater than that of Cr over the circulation of salt. Furthermore, the modeling accurately predicted the subsurface enrichment of Mo which is attributed to the reduced Cr activity and the relatively higher diffusion rate of Mo within the alloy matrix. Here, the agreement between modeling and experimental results confirms that Fe chlorides dissolve at the hot-leg and subsequently deposit at the cold-leg due to activity changes driven by the thermal gradient. By contrast, Cr was not detected in the cold-leg deposits, which is attributed to its weaker temperature dependence on activity, limiting its redeposition under these conditions.

36 - MATERIALS SCIENCE↗
DOE OSTI2021

Creep behavior of 316 L stainless steel manufactured by laser powder bed fusion

Additive manufacturing as a new processing technique can produce unique microstructure that is difficult to achieve using conventional techniques. Here, we have investigated the creep behavior of 316 L stainless steel produced by a laser powder bed fusion process at temperatures of 550, 600 and 650 °C and stresses between 175 and 300 MPa. We found that additively-manufactured 316 L stainless steel had a higher stress dependence of the minimum creep rate than conventionally-made Type 316 SS, which could be attributed to the dislocation cell structure resulting from the printing process. The dislocation cell structure was unstable under creep, evolving into a uniform dislocation structure under the test conditions. While internal porosity in AM 316 L SS may serve as nucleation sites of creep voids and may be responsible for a relatively lower creep life, additively-manufactured 316 SS did not show inferior creep ductility when compared with conventionally-made 316 SS. The creep life of AM 316 L SS could be improved by stabilizing dislocation cell structure and/or reducing internal porosity through an optimized additive manufacturing process.

316 L stainless steel↗
DOE OSTI2022

Characterization of multi-material 316L-Hastelloy X fabricated via laser powder-bed fusion

The aim of this work is to provide firsthand knowledge of 316 L stainless steel (316 L) and Hastelloy X (HX) multi-material processing via laser powder bed fusion (PBF). Specifically, microstructure of the interface is studied using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). Surface metrology is performed to characterize the resulting surface roughness at the interface followed by tensile and flexural testing of multi-material samples to characterize the mechanical properties of the interfaces. Results showed that use of proper process parameters for each individual material led to formation of a compositional gradient at the interface that stretched for 240 μm (10–12 layers) with no evidence of cracking or porosity. The interface exhibited higher surface roughness compared to 316 L or HX as measured by arithmetic mean height, Sa, and maximum valley depth, Sv, parameters. During tensile testing, samples failed in the 316 L region away from the interface, with comparable yield strength, ultimate strength, and ductility. Finally, it was concluded that the “naturally” formed interface created a compositional gradient which was defect free due to similar values of coefficient of thermal expansion, input energy density, and different Marangoni numbers of the materials.

316L stainless Steel↗
DOE OSTI2019

A Guideline for the Assessment of Uniaxial Creep and Creep-Fatigue Data and Models

Of primary concern to FE practitioners is a determination of which constitutive models are the “best”, capable of reproducing the mechanisms expected in an intended design accurately; as well as what experimental datasets are proper or “best” to use for fitting the constitutive parameters needed for the model(s) of interest. In addition, the inherent uncertainty in experiments and the repeatability and stability of extrapolations (for long-lived FE components) is a major concern. The goal of this project is to develop a guideline for the assessment of uniaxial creep and creep-fatigue data and models. The research objectives are RO1) develop an aggregated database of creep and creep-fatigue data for P91 steel and 316 stainless steel and perform a systematic assessment of the uncertainty and integrity of the datasets. RO2) employ the database to benchmark existing creep and creep-fatigue models to evaluate the model’s ability to predict standard and nonstandard boundary conditions.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Slag Degassing for Electroslag Remelting Using Cold Start

The effect of slag degassing prior to cold start electroslag remelting (ESR) was investigated using various heat treatments of a commercial 40CaF2 – 30CaO – 30Al2O3 slag. The slag was either degassed in a vacuum heat treatment furnace or in a box furnace in air. Vacuum heat treatment included partial pressure of Ar gas. Several temperatures, ramp rates and/or holding times were investigated for each condition and the pressure was monitored for the heat treatment in the furnace with controlled atmosphere. A research scale 200 kg capacity ESR furnace was used for the experiments along with 1018 steel and 316 stainless steel electrodes. Significant differences in ingot quality were related to the sidewall and the presence of pores which were primarily located near the bottom of the ingot. Adjustments in the heat treatment temperature for heat treatment in air eventually led to an ingot quality near that obtained using slag degassed under vacuum and/or in a controlled atmosphere.

Detrois, Martin↗