Search NASA⌕ Search

SEARCH · Search NASA

Results for “AERODYNAMIC COEFFICIENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

47 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Effect of Surface Roughness on Dynamic Stall in Pitching Motion

Dynamic stall plays a critical role in determining the performance and stability of a wide range of fluid-dynamics systems in various engineering applications. This unsteady aerodynamic phenomenon is particularly significant for maneuvering aircraft wings, jet aircraft subjected to gust encounters, helicopter rotor blades, and wind turbine blades [1–3]. The prediction of the dynamic stall vortex (DSV) is challenging due to factors such as unsteady aerodynamics, three-dimensional (3-D) effects, turbulence and flow separation, incoming gust, and surface impact effects [4–6]. Hence, advanced computational techniques and modeling approaches in computational fluid dynamics (CFD) would be required to enhance the accuracy and reliability of DSV predictions in dynamic stall scenarios. In the past, Batther and Lee [7] employed delayed detached eddy simulations (DDES) to understand the flow physics associated with the onset of dynamic stall. Their approach demonstrated that DDES achieves results comparable to those obtained from large-eddy simulations at a reduced computational cost. In another study, Khalifa et al. [8] examined the 3-D aspects of dynamic stall on a NACA 0012 airfoil using DES solvers. In conclusion, the findings underlined the superiority of 3-D simulations over two-dimensional approaches, particularly in predicting the lift coefficient values and capturing dynamic stall stages more precisely.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Numerical Investigation of Wall-Cooling Effect on Aero-Optical Distortions for Hypersonic Boundary Layer

Compressible wall-modeled large-eddy simulations of Mach 8 turbulent boundary-layer flows over a flat plate were carried out for the conditions of the hypersonic wind tunnel at Sandia National Laboratories. The simulations provide new insight into the effect of wall cooling on the aero-optical path distortions for hypersonic turbulent boundary-layer flows. Four different wall-to-recovery temperature ratios, 0.3, 0.48, 0.71, and 0.89, are considered. Despite the much lower grid resolution, the mean velocity, temperature, and resolved Reynolds stress profiles from the simulation for a temperature ratio of 0.48 are in good agreement with those from a reference direct numerical simulation. The normalized root-mean-square optical path difference obtained from the present simulations is compared with that from reference direct numerical simulations, Sandia experiments, as well as predictions obtained with a semi-analytical model by Notre Dame University. Here the present analysis focuses on the effect of wall cooling on the wall-normal density correlations, on key underlying assumptions of the aforementioned model such as the strong Reynolds analogy, and on the elevation angle effect on the optical path difference. Wall cooling is found to increase the velocity fluctuations and decrease the density fluctuations, resulting in an overall reduction of the normalized optical path distortion. Compared to the simulations, the basic strong Reynolds analogy overpredicts the temperature fluctuations for cooled walls. Also different from the strong Reynolds analogy, the velocity and temperature fluctuations are not perfectly anticorrelated. Finally, as the wall temperature is raised, the density correlation length, away from the wall but inside the boundary layer, increases significantly for beam paths tilted in the downstream direction.

42 ENGINEERING↗
DOE OSTI2024

Measurement report: The Fifth International Workshop on Ice Nucleation phase 1 (FIN-01): intercomparison of single-particle mass spectrometers

Knowledge of the chemical composition and mixing state of aerosols at a single-particle level is critical for gaining insights into atmospheric processes. One common tool to make these measurements is single-particle mass spectrometry. There remains a need to compare the performance of different single-particle mass spectrometers (SPMSs). An intercomparison of SPMSs was conducted at the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) chamber at the Karlsruhe Institute of Technology (KIT) in November 2014, as part of the first phase of the Fifth International Workshop on Ice Nucleation (FIN-01). In this paper we compare size distributions and mass spectra of atmospherically relevant particle types measured by five SPMSs. These include different minerals, desert and soil dusts, soot, bioaerosol (Snomax; protein granule), secondary organic aerosol (SOA), and SOA-coated mineral particles. Most SPMSs reported similar vacuum aerodynamic diameter (d va ) within typical instrumental ranges from ~100–200 nm (lower limit) to ~2–3 µm (upper limit). In general, all SPMSs exhibited a wide dynamic range (up to ~10 3 ) and high signal-to-noise ratio (up to ~10 4 ) in mass spectra. Common spectral features with small diversities in mass spectra were found with high average Pearson's correlation coefficients, i.e., for average positive spectra r avg-pos =0.74 ± 0.12 and average negative spectra r avg-neg =0.67 ± 0.22. We found that instrument-specific detection efficiency (DE) was more dependent on particle size than particle type, and particle identification favored the use of bipolar, rather than monopolar, instruments. Particle classification from “blind experiments” showed that all instruments differentiated SOA, soot, and soil dust and detected subtle changes in the particle internal mixing but had difficulties differentiating among specific mineral types and dusts. This study helps to further understand the capabilities and limitations of the single-particle mass spectrometry technique in general and the specific performance of the instrument in characterizing atmospheric aerosol particles.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2025

Effect of artificial viscosity on shocked particle-laden flows for staggered grid Lagrangian methods

Abstract Shocked particle-laden flows are important to many natural and industrial processes. When simulating these systems, artificial viscosity is often required to prevent numerical artifacts, such as ringing, from arising in the pressure and density fields. The linear and quadratic coefficients of the artificial viscosity determine the amount of smoothing that occurs in these fields. For particle-laden flows, however, many of the fluid–particle interaction forces, for example, the pressure gradient force and unsteady forces, depend on gradients in the fluid fields. Furthermore, while the shock passes over a particle, these forces can be more dominant than drag. This means that the artificial viscosity coefficients affect how a particle and fluid interact when simulating shocked particle systems. Here this effect is investigated for isolated particles and for a particle curtain using a staggered grid Lagrangian approach. The artificial viscosity coefficients have a significant impact on the maximum force that a fluid imparts to a particle, which is important for determining whether a particle will break up in response to the shock. Furthermore, it is found that the density ratio between the particle and the fluid is important in determining whether the artificial viscosity coefficients have a significant impact on the particle’s motion.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Aerosol emissions from water-lean solvents for post-combustion CO 2 capture

Advanced water-lean solvents (WLS) for post-combustion CO 2 capture have been gaining interest due to their ability to reduce the parasitic penalty from energy needed for solvent regeneration. Commercial implementation of these novel CO 2 capture technologies hinges on successful control of amine emissions. RTI conducted a parametric study of fundamental and operational variables influence on overall amine aerosol and vapor emissions from our water-lean solvent eCO 2 Sol™ using our 6-kW equivalent bench-scale gas absorption system. The parametric testing used a simulated flue gas with 15 % CO 2 , 2.3–4.2 % H 2 O, and 0–6 ppm sulfite (SO 3 ) to examine the impact of the presence of aerosols to the capture performance and amine emissions from the system. The SO 3 reacts with water in the flue gas to create H 2 SO 4 , which forms liquid aerosol droplets and provide nucleation sites for growth of aerosols. Scanning Mobility Particle Sizer and Aerodynamic Particle Sizer instruments monitored the aerosol particle size distribution. Parametric testing results suggested that the presence of the aerosols in the flue gas could increase the overall amine emissions by 10X compared to the baseline emissions from WLS’s vapor pressure. Principal component analysis (PCA) and projection to latent squares (PLS) developed models to predict the aerosol-based amine emissions from process data. The predictive PLS model had a correlation coefficient (Q 2 ) of 0.92 and could predict the aerosol-based emissions from the NAS process with ±15 % accuracy (average absolute deviation, AAD). The PLS regression model also identified key variables affecting aerosol-based emissions from WLS.

42 ENGINEERING↗
DOE OSTI2022

NUMERICAL PREDICTIONS OF MEAN PERFORMANCE AND DYNAMIC BEHAVIOR OF A 10 MWe SCO2 COMPRESSOR WITH TEST DATA VALIDATION

High-fidelity aerodynamic analysis has been demonstrated for mean performance and unsteady dynamics in a sCO2 compressor designed by Hanwha Power Systems Americas for a 10 MWe Concentrating Solar Power plant. Simulations were performed with CRUNCH CFD® software tool that was matured to accurately model near critical real fluid effects in sCO2. Pre-test predictions for mean performance were validated with test data collected later. Performance predictions were accurate and captured sensitivity of the efficiency to inlet temperature of CO2 as well as steep drop-off at high flow rates due to condensation in the inlet throat. Detailed analysis was performed to understand the source of these performance losses at near critical conditions. Unsteady dynamic effects in the compressor at off-design conditions were also identified and quantified. In particular a system wide “condensation surge” condition was detected at high flow coefficients that results in large amplitude pulsations with accompanying mass flow fluctuations at low frequencies and has potential to cause damage in closed loop systems.

hosangadi, ashvin↗
DOE OSTI2023

Turbulent entrainment in finite-length wind farms

In this article, we present an entrainment-based model for predicting the flow and power output of finite-length wind farms. The model is an extension of the three-layer approach of Luzzatto-Fegiz & Caulfield ( Phys. Rev. Fluids , vol. 3, 2018, 093802) for wind farms of infinite length, and assumes dependence of key flow quantities, such as the wind farm bulk velocity, on the streamwise distance from the farm entrance. To assist our analysis and validate the proposed model, we undertake a series of large-eddy simulations with different turbine spacing arrangements and layouts. Comparisons are also made with the top-down model with entrance effects of Meneveau ( J. Turbul. , vol. 13, 2012, N7) and data from the literature. The finite-length entrainment model is shown to be capable of capturing the power drop between contiguous rows of turbines as well as describing the advection and turbulent transport of kinetic energy in both the entrance and fully developed regions. The fully developed regime is approximated only deep in the wind farm, after approximately 15 rows of turbines. Our data suggest that for the cases considered in this study, the empirical coefficients that can be used to describe turbulent entrainment and transfers above the wind farm exhibit little dependence on the farm layout and may be considered constant for modelling purposes. However, the flow field within the wind farm layer can be strongly modulated by the turbine density (spacing) as well as the array layout, and to that extent it can be argued that they are both primary factors determining the wind farm power output.

17 WIND ENERGY↗
DOE OSTI2026

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation) [SWR-26-095]

FOILPOLARS (Grassmannian Foil Shape Sweeps for Polar Generation): Multifidelity aerodynamic polar data generation for hydrofoil/tidal-turbine airfoil sections. Foilpolars ties together three pieces: *AeroSandbox supplies the baseline airfoil coordinates (UIUC database). *G2Aero parameterizes those shapes on a Grassmannian manifold (Karcher mean + PGA basis) and samples new perturbed shapes around that basis. *XFoil (panel method) and NeuralFoil (neural-network surrogate, shipped with AeroSandbox) each solve the resulting shapes for lift, drag, moment, and pressure at the swept angles of attack, Reynolds numbers, and n_crit values. Design optimization of foil shapes in a computationally efficient way requires polars data across many candidate shapes, not just a handful of baseline foils. However, high-fidelity CFD at that scale is too costly, and naive shape perturbation strays from realistic geometries. FOILPOLARS addresses this by loading baseline airfoils (via AeroSandbox) and mapping them onto a Grassmannian manifold (via G2Aero), computing a Karcher mean and principal geodesic analysis (PGA) basis. New shapes are sampled by perturbing PGA coefficients, keeping them close to the manifold of realistic foils. Each sampled shape is evaluated across a configurable sweep of angle of attack, Reynolds number, and critical amplification factor using two solvers: XFoil (panel method) and NeuralFoil (neural-network surrogate), producing a paired dataset of lift, drag, moment, pressure, convergence, and confidence, indexed alongside each shape's PGA coefficients and shared Grassmannian basis in a single xarray dataset. From this, FOILPOLARS produces convergence summaries and comparison plots per shape, Reynolds number, and n_crit. A command-line interface exposes each pipeline stage independently, supporting data-driven design, optimization, and machine-learning workflows for foils.

Sandhu, Rimple [National Laboratory of the Rockies↗
DOE OSTI2022

Towards new zero-thermal-expansion materials: Li-free quartz solid solutions stuffed with transition metal cations

Stuffed aluminosilicate quartz solid solutions (Qss) represent the main functional component of state-of-the-art zero-thermal-expansion glass-ceramics. For the first time, we present the synthesis of Li-, Mg- and Zn-free Qss solely stuffed with transition metal cations (Fe 2+ , Ni 2+ , Co 2+ ); partial Li + co-doping enables also significant Mn 2+ incorporation. Further, they were obtained by glass powder crystallization; Qss crystals exhibit compositionally tunable coefficients of thermal expansion (CTEs), from - 2 × 10 -6 K -1 to ~10 × 10 -6 K -1 in the range 30–300 °C. Co 2+ -bearing crystals exhibit the closest-to-zero CTE value (0.2 ×10 -6 K -1 ) and the most isotropic behavior in the whole Qss family, opening up new perspectives for the development of Li-free low-expansion materials. From a structural point of view, we identified the unit cell volume (and not the pseudo-hexagonality of the aluminosilicate framework) as the key structural parameter leading to low or negative CTEs in Qss, with a linear correlation extending to non-stuffed non-silicate quartz-like phases.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Model bias in simulating major chemical components of PM 2.5 in China

High concentrations of PM 2.5 (particulate matter with an aerodynamic diameter less than 2.5 µm) in China have caused severe visibility degradation. Accurate simulations of PM 2.5 and its chemical components are essential for evaluating the effectiveness of pollution control strategies and the health and climate impacts of air pollution. In this study, we compared the GEOS-Chem model simulations with comprehensive datasets for organic aerosol (OA), sulfate, nitrate, and ammonium in China. Model results are evaluated spatially and temporally against observations. The new OA scheme with a simplified secondary organic aerosol (SOA) parameterization significantly improves the OA simulations in polluted urban areas, highlighting the important contributions of anthropogenic SOA from semivolatile and intermediate-volatility organic compounds. The model underestimates sulfate and overestimates nitrate for most of the sites throughout the year. More significant underestimation of sulfate occurs in winter, while the overestimation of nitrate is extremely large in summer. The model is unable to capture some of the main features in the diurnal pattern of the PM 2.5 chemical components, suggesting inaccuracies in the presented processes. Potential model adjustments that may lead to a better representation of the boundary layer height, the precursor emissions, hydroxyl radical concentrations, the heterogeneous formation of sulfate and nitrate, and the wet deposition of nitric acid and nitrate have been tested in the sensitivity analysis. The results show that uncertainties in chemistry perhaps dominate the model biases. The proper implementation of heterogeneous sulfate formation and the good estimates of the concentrations of sulfur dioxide, hydroxyl radical, and aerosol liquid water are essential for the improvement of the sulfate simulation. The update of the heterogeneous uptake coefficient of nitrogen dioxide significantly reduces the modeled concentrations of nitrate. However, the large overestimation of nitrate concentrations remains in summer for all tested cases. The possible bias in the chemical production and the wet deposition of nitrate cannot fully explain the model overestimation of nitrate, suggesting issues related to the atmospheric removal of nitric acid and nitrate. A better understanding of the atmospheric nitrogen budget, in particular, the role of the photolysis of particulate nitrate, is needed for future model developments. Moreover, the results suggest that the remaining underestimation of OA in the model is associated with the underrepresented production of SOA.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Barriers and variable spacing enhance convective cooling and increase power output in solar PV plants

When the temperature of solar photovoltaic (PV) modules rises, efficiency drops and module degradation accelerates. Thus, it is beneficial to reduce module operating temperatures. Previous studies of solar power plants have illustrated that incoming flow characteristics, turbulent mixing, and array geometry can strongly impact convective cooling, as measured by the convective heat transfer coefficient h. In the fields of heat transfer and plant canopy flow, previous work has shown that system-scale arrangement modifications—e.g., variable spacing, barriers, or windbreaks—can passively alter the flow, enhance turbulent mixing, and influence convection. However, researchers have not yet explored how variable spacing or barriers might enhance convective cooling in solar power plants. Here, high-resolution large-eddy simulations model the air flow and heat transfer through solar power plant arrangements modified with missing modules and barrier walls. We then perform a control volume analysis to evaluate the net heat flux and compute h, which quantifies the influence of these spatial modifications on convective cooling and, thus, module temperature and power output. Installing barrier walls yields the greatest improvements, increasing h by 3.4%, reducing module temperature by an estimated 2.5 °C, and boosting power output by an estimated 1.4% on average. These findings indicate that incorporating variable spacing or barrier-type elements into PV plant designs can reduce module temperature and, thus, improve PV performance and service life.

14 SOLAR ENERGY↗