SEARCH · Search NASA

Results for “AILERONS - HINGE MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

All sources NASA NTRS DOE OSTI

NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack II : slotted ailerons and frise ailerons

Three model wings, two with typical slotted ailerons and one with typical frise ailerons, have been tested as part of a general investigation on lateral control devices with particular reference to their effectiveness at high angles of attack, in the 7 by 10 foot wind tunnel of the National Advisory Committee for Aeronautics. Force tests, free-autorotation tests, and forced-rotation tests were made which show the effect of the various ailerons on the general performance of the wing, on the lateral controllability, and on the lateral stability, in general, rolling control at 20 degree angle of attack to plain ailerons of the same size. The adverse yawing moments obtained with the slotted and frise ailerons were, in most cases, slightly smaller than those obtained with plain ailerons of the same size and deflection. However, this improvement was small as compared to the improvement obtainable by the use of suitable differential movements with any of the ailerons, including the plain.

Weick, Fred E↗

NASA NTRS1984

The lateral-directional characteristics of a 74-degree Delta wing employing gothic planform vortex flaps

The low speed lateral/directional characteristics of a generic 74 degree delta wing body configuration employing the latest generation, gothic planform vortex flaps was determined. Longitudinal effects are also presented. The data are compared with theoretical estimates from VORSTAB, an extension of the Quasi vortex lattice Method of Lan which empirically accounts for vortex breakdown effects in the calculation of longitudinal and lateral/directional aerodynamic characteristics. It is indicated that leading edge deflections of 30 and 40 degrees reduce the magnitude of the wing effective dihedral relative to the baseline for a specified angle of attack or lift coefficient. For angles of attack greater than 15 degrees, these flap deflections reduce the configuration directional stability despite improved vertical tail effectiveness. It is shown that asymmetric leading edge deflections are inferior to conventional ailerons in generating rolling moments. VORSTAB calculations provide coarse lateral/directional estimates at low to moderate angles of attack. The theory does not account for vortex flow induced, vertical tail effects.

Grantz, A. C.↗

NASA NTRS1921

Measurements of Rudder Moments on an Airplane During Flight

Tests indicated that: 1) C airplanes with two struts are extremely susceptible to aileron maneuvers, slight alterations of the aileron sufficing to compensate great unequalized moments; 2) great unequalized moments can be produced or neutralized by the unequalized alternation of the angle of attack below the outer and inner struts. Adjustment below the outer strut is the more effective of the two. 3) When a load of bombs is suspended beyond the center of the airplane, below the wings, the bombs need not be dropped simultaneously. 4) The propeller wash of a wide open engine has considerable influence on the position and operation of the elevator. The elevator is more susceptible in flight with the engine running than in gliding flight. 5) Adjustable tail planes are not advisable for D airplanes, nor for the C type, but they are, on the other hand, to be recommended for large size and giant airplanes in which the center of gravity changes during flight. 6) The aileron values obtained by wind tunnel measurements are about 10 percent too low, though otherwise applicable. For the elevator, the results of such measurements should be taken as mean values between flight with the engine running and gliding flight.

Heidelberg, Ing V↗

NASA NTRS1945

Wind-Tunnel Investigation of a Rectangular NACA 2212 Airfoil with Semispan Ailerons and with Nonperforated, Balanced Double Split Flaps for Use as Aerodynamic Brakes

Flat-plate flaps with no wing cutouts and flaps having Clark Y sections with corresponding cutouts made in wing were tested for various flap deflections, chord-wise locations, and gaps between flaps and airfoil contour. The drag was slightly lower for wing with airfoil section flaps. Satisfactory aileron effectiveness was obtained with flap gap of 20% wing chord and flap-nose location of 80 percent wing chord behind leading edge. Airflow was smooth and buffeting negligible.

AIRFOILS - NACA 2212 - CHAR & MOMENTS - WING FLAPS↗

NASA NTRS1927

Distribution of Pressure Over Model of the Upper Wing and Aileron of a Fokker D-VII Airplane

This report describes tests made for the purpose of determining the distribution of pressure over a model of the tapered portion of the upper wing and the aileron of a Fokker D-VII Airplane. Normal pressures were measured simultaneously at 74 points distributed over the wing and aileron. Tests were made throughout the useful range of angles of attack with aileron setting ranging from -20 degrees to +20 degrees. The results are presented graphically. It was found that the pressure distribution along the chord is in general similar to that of thick tapered airfoils previously tested. The maximum resultant pressure recorded was five times the dynamic pressure. The distribution of the air load along the span may be assumed to be uniform for design purposes. Aileron displacements affect the pressures forward to the leading edge of the wing and may increase the air load on the outer portion of the wing by a considerable amount. With the wing at large angles of attack, the overhanging portion of the aileron creates usually a burble flow and therefore a large drag. The balance reduces the control stick forces at small angles of attack for all aileron displacements. At large angles of attack it does this for small displacements only. With the airplane at its maximum speed, an angle of attack of 18 degrees, and a down aileron displacement of 20 degrees, the bending moment tending to break off the overhanging portion of the aileron will be greater than that caused by a uniform static load of 35 pounds per square foot.

Fairbanks, A J↗

NASA NTRS1955

Qualitative Results from a Flight Investigation to Determine Aileron Effectiveness of Two Rocket-Propelled 1/20-Scale Models of the MX -76 Missile

Free-flight tests of two rocket-propelled l/20-scale models of the Bell MX-776 missile have been conducted to obtain measurements of the aileron deflection required to counteract the induced rolling moments caused by combined angles of attack and sideslip and thus to determine whether the ailerons provided were capable of controlling the model at the attitudes produced by the test conditions. Inability to obtain reasonably steady-state conditions and superimposed high-frequency oscillations in the data precluded any detailed analysis of the results obtained from the tests. For these reasons, the data presented are limited largely to qualitative results.

Stevens, Joseph E.↗

NASA NTRS1983

Inherent spiral stability in a fixed wing aircraft by means of a simplified pneumatic wing tip control system

The concept of the lateralizer device is to sense the difference in wing tip static pressures (differential pressures being created by wing tip venturis) produced when any deviation from straight to level flight occurs. In a steady state turn the low slow wing tip experiences less venturi suction than the high fast wing tip. This signal activates the appropriate servos connected to the ailerons to produce a wing leveling restoring moment. If the wing is subjected to rolling velocities due to changes of the local angle of attack at the tip, the downgoing wing tip operates at a higher angle than the upgoing one. If with an increase in the angle of attack the signal is such that it increases the venturi pressure, then the servos are activated to produce the most negative signal to an upgoing aileron which results in a wing leveling restoring moment. In other words, any deviation from straight and level flight in either roll or yaw is exploited and the difference signal from the differential pressures activates the servo to effect or produce the necessary corrective action to null the signal.

Goglia, G. L.↗

NASA NTRS1940

A study of unsymmetrical-loading conditions

The force variation along the wing span under combined normal and angular accelerations is considered. Non dimensional curves of section load, shear, and moment are given for: (1) the air load that produces a normal acceleration; (2) the accompanying wing weight and normal inertia loads; (3) aileron and gust air loads that produce angular acceleration; (4) the angular inertia load of the wing. The required aerodynamic load distributions have been obtained by use of wing theory, and the wing inertia distributions are based on an analysis of wing-weight data. Several examples are included to illustrate the effect of wing taper and aileron span on the total shears and moments at any section along the span.

Pearson, Henry A↗

NASA NTRS1959

Investigation of the Stability of Very Flat Spins and Analysis of Effects of Applying various Moments Utilizing the Three Moment Equations of Motion

Based on linearized equations of motion utilizing only the three moment equations and assuming only flat-spin conditions, it appears that contemporary designs (with the moment of inertia about the wing axis I(sub Y) considerably greater than the moment of inertia about the fuselage axis I(sub X) having positive values of C(sub l, sub p) (rolling-moment coefficient due to rolling) or positive values of C(sub l, sub beta) (rolling-moment coefficient due to sideslip) will probably not have a stable spin in the flat-spin region near an angle of attack of 90 deg. If the damping in pitch in flat-spin attitudes is zero, stable flat-spin conditions may not be possible on an airplane having the mass primarily distributed along the wings. The effect of moving ailerons with the spin or the effect of applying a positive pitching moment producing recovery for contemporary fighter designs will be greatest for large negative values of C(sub n, sub beta) (yawing-moment coefficient due to sideslip). In addition, for a certain critical value of positive C(sub n, sub beta), the rolling moment applied by moving ailerons with the spin or the application of a positive pitching moment will have no effect on reducing the spin rate.

Klinar, Walter J.↗

NASA NTRS2024

Computational Analysis of the X-57 Maxwell Airplane, the Landing Configuration with High-Lift Blowing and Aileron Deflections (Preliminary Fuselage)

The X-57 Maxwell is an all-electric airplane with a distributed electric propulsion system used for a high-lift system at takeoff and landing conditions. The Kestrel and USM3D flow solvers were used at NASA Langley to investigate the performance of the X-57 Maxwell in the development of an aerodynamic database. The configuration investigated in this paper had a 30° flap deflection, and in addition the pilot’s right aileron were deflected and undeflected in different cases. The solutions were computed at an airspeed of 58 KEAS, for an altitude of 6000 feet, and a flight Reynolds number of 0.588e+06 per foot. To evaluate the high-lift distributed electric propulsion system without aileron deflections, the solutions were computed for an angle-of-attack sweep from −2° to 20°, with the high-lift propellers blowing and the cruise propellers excluded from the simulation. To investigate the aileron effectiveness, the solutions were computed at angles of attack of −2° and 14°, for aileron deflections from −25° to 18° with the high-lift propellers blowing and the cruise propellers windmilling at idle-power. The high-lift propellers and the idle-power cruise propellers were modeled with an actuator disk. Results show negligible differences in lift, drag and pitching moment whether the idle-powered cruise propellers were included or excluded from the simulation. In general, the Kestrel and USM3D codes compared well for lift, drag and pitching moment for the landing configuration with no aileron control. The Kestrel code, using the Spalart-Allmaras turbulence model with the rotation corrections terms, predicted an increasing lift coefficient up to maximum lift coefficient of 4.65 at a 15° angle of attack. The USM3D code, using the Spalart-Allmaras turbulence model turbulence model with the Quadratic Constitutive Relation predicted an increasing lift coefficient up to maximum lift coefficient of 4.5 at a 12° angle of attack, with the lift remaining constant through a 14◦ angle of attack. A possible difference in lift coefficient between the codes for high angles of attack may result from the different available options used with the standard Spalart-Allmaras turbulence model. The Kestrel code predicted more drag across the range of angle of attack than the USM3D code. The codes compared well for pitching moment coefficient across the range of angle of attack. The Kestrel and USM3D codes compared well for aileron effectiveness at a 2° angle of attack. The Kestrel code predicts better aileron effectiveness than USM3D at a 14° angle of attack. There is more flow separation in the region outboard of the last high-lift nacelle for the USM3D solutions at a 14° angle of attack, which diminishes the ability of the aileron to be effective.

X-57 Maxwell Airplane↗

NASA NTRS1983

Aileron effectiveness for a subsonic transport model with a high-aspect-ratio supercritical wing

Aileron effectiveness for a subsonc energy efficient transport (EET) model with a high aspect ratio supercritical wing was determined in the 8-foot transonic pressure tunnel. Data are presented for ailerons located at three positions along the wing span. The ailerons were designed as a preliminary active control concept with gust load alleviation, maneuver load alleviation, and flutter suppression systems. A linear variation of rolling moment coefficient with angle of attack for individual and multiple aileron deflections at Mach numbers up to 0.81 is indicated. For Mach numbers greater than 0.81, the rolling moment coefficient data become nonlinear with increasing angle of attack. At Mach numbers near the design value increased aileron effectiveness resulted from aft transition locations, which produced relatively thin boundary layers and greater effective aileron deflections. Individual aileron deflections on the right wing panel produced only small effects on yawing moment and side force coefficients.

Jacobs, P. F.↗

NASA NTRS2000

Reynolds Number Effects on the Performance of Lateral Control Devices

The influence of Reynolds number on the performance of outboard spoilers and ailerons was investigated on a generic subsonic transport configuration in the National Transonic Facility over a chord Reynolds number range 41 from 3x10(exp 6) to 30xl0(exp 6) and a Mach number range from 0.50 to 0.94, Spoiler deflection angles of 0, 10, 15, and 20 deg and aileron deflection angles of -10, 0, and 10 deg were tested. Aeroelastic effects were minimized by testing at constant normalized dynamic pressure conditions over intermediate Reynolds number ranges. Results indicated that the increment in rolling moment due to spoiler deflection generally becomes more negative as the Reynolds number increases from 3x10(exp 6) to 22x10(exp 6) with only small changes between Reynolds numbers of 22x10(exp 6) and 30x10(exp 6). The change in the increment in rolling moment coefficient with Reynolds number for the aileron deflected configuration is generally small with a general trend of increasing magnitude with increasing Reynolds number.

Mineck, Raymond E.↗

NASA NTRS2001

Reynolds Number Effects on the Performance of Ailerons and Spoilers (Invited)

The influence of Reynolds number on the performance of outboard spoilers and ailerons was investigated on a generic subsonic transport configuration in the National Transonic Facility over a chord Reynolds number range from 3 to 30 million and a Mach number range from 0.70 to 0.94. Spoiler deflection angles of 0, 10, and 20 degrees and aileron deflection angles of -10, 0, and 10 degrees were tested. Aeroelastic effects were minimized by testing at constant normalized dynamic pressure conditions over intermediate Reynolds number ranges. Results indicated that the increment in rolling moment due to spoiler deflection generally becomes more negative as the Reynolds number increases from 3 x 10(exp 6) to 22 x 10 (exp 6) with only small changes between Reynolds numbers of 22 x 10(exp 6) and 30 x 10(exp 6). The change in the increment in rolling moment coefficient with Reynolds number for the aileron deflected configuration is generally small with a general trend of increasing magnitude with increasing Reynolds number.

Mineck, R. E.↗

NASA NTRS1990

Static Wind-Tunnel and Radio-Controlled Flight Test Investigation of a Remotely Piloted Vehicle Having a Delta Wing Planform

At the request of the United States Marine Corps, an exploratory wind-tunnel and flight test investigation was conducted by the Flight Dynamics Branch at the NASA Langley Research Center to improve the stability, controllability, and general flight characteristics of the Marine Corps Exdrone RPV (Remotely Piloted Vehicle) configuration. Static wind tunnel tests were conducted in the Langley 12 foot Low Speed Wind Tunnel to identify and improve the stability and control characteristics of the vehicle. The wind tunnel test resulted in several configuration modifications which included increased elevator size, increased vertical tail size and tail moment arm, increased rudder size and aileron size, the addition of vertical wing tip fins, and the addition of leading-edge droops on the outboard wing panel to improve stall departure resistance. Flight tests of the modified configuration were conducted at the NASA Plum Tree Test Site to provide a qualitative evaluation of the flight characteristics of the modified configuration.

Yip, Long P.↗

NASA NTRS1990

Wind-tunnel and flight-test investigation of the exdrone remotely piloted vehicle configuration

At the request of the United States Marine Corps, an exploratory wind-tunnel and flight test investigation was conducted by the NASA Langley Research Center to improve the stability, controllability, and general flight characteristics of the Marine Corps Exdrone RPV (Remotely Piloted Vehicle) configuration. Static wind tunnel tests were conducted to identify and improve the stability and control characteristics of the vehicle. The wind-tunnel test resulted in several configuration modifications which included increased elevator area, increased vertical tail area and moment arm, increased rudder area and aileron area, the addition of vertical wing-tip fins, and the addition of leading-edge droops on the outboard wing panel to improve the stall departure resistance. Flight tests of the modified configuration were conducted at the NASA Plum Tree Test Site to provide a qualitative evaluation of the flight characteristics of the modified configuration.

Yip, Long P.↗

NASA NTRS1992

A preliminary look at an optimal multivariable design for propulsion-only flight control of jet-transport aircraft

Control of a large jet transport aircraft without the use of conventional control surfaces was studied. Engine commands were used to attempt to recreate the forces and moments typically provided by the elevator, ailerons, and rudder. Necessary conditions for aircraft controllability were developed pertaining to aircraft configuration such as the number of engines and engine placement. An optimal linear quadratic regulator controller was developed for the Boeing 707-720, in particular, for regulation of its natural dynamic modes. The design used a method of assigning relative weights to the natural modes, i.e., phugoid and dutch roll, for a more intuitive selection of the cost function. A prototype pilot command interface was then integrated into the loop based on pseudorate command of both pitch and roll. Closed loop dynamics were evaluated first with a batch linear simulation and then with a real time high fidelity piloted simulation. The NASA research pilots assisted in evaluation of closed loop handling qualities for typical cruise and landing tasks. Recommendations for improvement on this preliminary study of optimal propulsion only flight control are provided.

Azzano, Christopher P.↗

NASA NTRS1959

Flight Behavior of the X-2 Research Airplane to a Mach Number of 3.20 and a Geometric Altitude of 126,200 Feet

The maximum Mach number and altitude capabilities of the Bell X-2 research airplane were achieved during a program conducted by the U.S. Air Force with Bell Aircraft Corp. providing operational support and the National Aeronautics and Space Administration providing instrumentation and advisory engineering assistance. A maximum geometric altitude of 126,200 feet was attained at a static pressure of 9.4 pounds per square foot and a dynamic pressure of 19.1 pounds per square foot. During the last flight of the airplane, a maximum Mach number of 3.20 was reached. The directionally divergent maneuver which terminated the final high Mach number flight was precipitated by the loss in directional stability that resulted from increasing the angle of attack. The yawing moment from the lateral control was sufficient to initiate the divergence and also to cause,, indirectly, rolling moments that were greater than the aileron capabilities of the airplane. The ensuing violent motions-resulting from inertial roll coupling caused the loss of the aircraft.

Day, Richard E.↗

NASA NTRSDate not supplied

Testing of High-Lift Common Research Model at Takeoff Configurations

The 10% scale High-Lift Common Research Model (CRM-HL) was tested in the NASA Langley 14- by 22-Foot Subsonic Tunnel (14x22) in support of the NASA Advanced Air Transport Technology (AATT) Project. The main objective of the wind tunnel test was to improve the aerodynamic performance of a representative aircraft model during takeoff operations using localized active flow control (AFC). This approach involves the application of AFC concepts locally to a relatively small region; therefore, it has the potential to cause minimal architectural change to current aircraft configurations. In addition, the power requirements of localized AFC could be supplied with onboard air resources. Recent exploratory studies identified the aileron as a target area for improving lift-to-drag ratio using localized AFC concepts. The idea is to deflect the ailerons beyond their nominal deflection angles and use AFC to reduce flow separation that occurs at larger aileron deflections. Several AFC concepts with different configurations were evaluated with the goal of achieving high-lift performance improvement. The assessment of AFC configurations is reported in a companion paper. The focus of the current paper is to report the data relevant to the CRM-HL takeoff configurations and establish a reference case for localized AFC application. Three takeoff configurations —reference, nominal, and high-lift improved—are documented. These takeoff configurations are obtained by varying aileron deflection. Wind tunnel measurements including surface static pressures and force and moment data are presented. In addition, surface tuft flow visualization, mainly on the aileron, is provided to understand the flow characteristics developed over the aileron during takeoff.

Lift-to-Drag↗