Search NASA⌕ Search

SEARCH · Search NASA

Results for “ALUMINUM ALLOYS - STRENGTH, COMPRESSIVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Modeling The Effects of Loading Scenario and Thermal Expansion Coefficient on Potential Failure of Cryo-compressed Hydrogen Vessels

A multiscale thermomechanical model for a simplified Type-3 cryogenic compressed hydrogen (H2) storage vessel is developed in this paper. The model accounts for the temperature-dependent elastic-plastic behavior of the vessel carbon/epoxy composite overwrap and aluminum alloy liner. The homogenized thermo-elastic-plastic behavior for the individual laminas of the vessel layup is obtained by an incremental Eshelby-Mori-Tanka approach associated with a micromechanical failure criterion to predict lamina failure while a standard elastic-plastic constitutive model is used to describe the behavior of a typical aluminum alloy assumed for the liner. The vessel response to external loadings is achieved by a finite element method. Four loading scenarios representing four thermomechanical cycles applied to the vessel are analyzed to evaluate constituent and lamina stresses as well as the associate failure criterion during the cycle according to these scenarios. The model can provide helpful guidance to mitigate thermal stresses by an adequate selection of loading scenario, optimizing the layup and by tailoring thermomechanical properties of the resin matrix.

36 MATERIALS SCIENCE↗
NASA NTRS1985

A study of spectrum fatigue crack propagation in two aluminum alloys. 1: Spectrum simplification

The fatigue crack propagation behavior of two commercial Al alloys was studied using spectrum loading conditions characteristics of those encountered at critical locations in high performance fighter aircraft. A tension dominated (TD) and tension compression (TC) spectrum were employed for each alloy. Using a mechanics-based analysis, it was suggested that negative loads could be eliminated for the TC spectrum for low to intermediate maximum stress intensities. The suggestion was verified by subsequent testing. Using fractographic evidence, it was suggested that a further similification in the spectra could be accomplished by eliminating low and intermediate peak load points resulting in near or below threshold maximum peak stress intensity values. It is concluded that load interactions become more important at higher stress intensities and more plasticity at the crack tip. These results suggest that a combined mechanics/fractographic mechanisms approach can be used to simplify other complex spectra.

Telesman, J.↗
NASA NTRS2012

Ultra-Lightweight Nanocomposite Foams and Sandwich Structures for Space Structure Applications

Microcellular nanocomposite foams and sandwich structures have been created to have excellent electrical conductivity and radiation-resistant properties using a new method that does not involve or release any toxicity. The nanocomposite structures have been scaled up in size to 12 X 12 in. (30 X 30 cm) for components fabrication. These sandwich materials were fabricated mainly from PE, CNF, and carbon fibers. Test results indicate that they have very good compression and compression-after-impact properties, excellent electrical conductivity, and superior space environment durability. Compression tests show that 1000 ESH (equivalent Sun hours) of UV exposure has no effect on the structural properties of the sandwich structures. The structures are considerably lighter than aluminum alloy (= 36 percent lighter), which translates to 36 percent weight savings of the electronic enclosure and its housing. The good mechanical properties of the materials may enable the electronic housing to be fabricated with a thinner structure that further reduces the weight. There was no difficulty in machining the sandwich specimens into electronic enclosure housing.

Tan, Seng↗
NASA NTRS2011

Evaluation of Aluminum Alloy 2050-T84 Microstructure and Mechanical Properties at Ambient and Cryogenic Temperatures

Aluminum alloy 2050 is being considered for the fabrication of cryogenic propellant tanks to reduce the mass of future heavy-lift launch vehicles. The alloy is available in section thicknesses greater than that of the incumbent aluminum alloy, 2195, which will enable designs with greater structural efficiency. While ambient temperature design allowable properties are available for alloy 2050, cryogenic properties are not available. To determine its suitability for use in cryogenic propellant tanks, tensile, compression and fracture tests were conducted on 4 inch thick 2050-T84 plate at ambient temperature and at -320degF. Various metallurgical analyses were also performed in order to provide an understanding of the compositional homogeneity and microstructure of 2050.

Hafley, Robert A.↗
NASA NTRS1940

The Lateral Stability of Equal-flanged Aluminum-alloy I-beams Subjected to Pure Bending

Equal-flange beams of a special extruded I-section of 27ST aluminum alloy were tested in pure bending. Complete end fixity was not attained. Loading was continued until a definite maximum value had been reached. Tensile tests were made on specimens cut from the flanges and the web of each beam. Compressive stress-strain characteristics were determined by pack compression tests on specimens cut from the flanges. Values computed from an equation previously suggested by one of the authors for the critical stress at which such beams become unstable were found to be in good agreement with values computed from experimentally determined critically bending moments.

Dumont, C↗
DOE OSTI2024

The derivation of CRSS in pure Ti and Ti-Al alloys

The work focuses on the determination of the critical resolved shear stress (CRSS) in titanium (Ti) and titanium-aluminum (Ti-Al) alloys, influenced by an array of factors such as non-symmetric fault energies and minimum energy paths, dislocation core-widths, short-range order (SRO) effects which alter the local atomic environment, and tension-compression (T-C) asymmetry affected by intermittent slip motion. To address these multifaceted complexities, an advanced theory has been developed, offering an in-depth understanding of the mechanisms underlying slip behavior. The active slip systems in these materials are basal, prismatic, and pyramidal planes, with the latter involving both $\langle$a$\rangle$ and $\langle$c + a$\rangle$ dislocations. Each slip system is characterized by distinct Wigner-Seitz cell configurations for misfit energy calculations, varying partial dislocation separation distances, and unique dislocation trajectories—all critical to precise CRSS calculations. The theoretical CRSS results were validated against a comprehensive range of experimental data, demonstrating a strong agreement and underscoring the model's efficacy.

Critical stress↗
NASA NTRS1972

Fatigue crack growth from a circular hole with and without high prior loading

Fatigue crack growth from a circular hole was investigated experimentally and analytically. An aluminum-alloy sheet specimen was cycled under a single level of loading with and without prior high loads. Tests showed that the crack propagation life was significantly longer when the high loads were applied initially. This longer life was attributed to compressive residual stresses produced near the hole by the initial high loads. The residual stresses near the hole were determined by an elastoplastic analysis and were then used to develop a stress-intensity solution for a crack growing through the residual stress field. This solution and a similar solution for the case of no prior loading were used to predict crack growth. The predicted crack growth agreed closely with the experimental values.

Crews, J. H., Jr.↗
NASA NTRS1939

Experimental Study of Deformation and of Effective Width in Axially Loaded Sheet-stringer Panels

The deformation of two sheet-stringer panels subjected to end compression under carefully controlled end conditions was measured at a number of points and at a number of loads, most of which were above the load at which the sheet had begun to buckle. The two panels were identical except for the sheet, which was 0.70-inch 24st alclad for specimen 1 and 0.025-inch 24st aluminum alloy for specimen 6. A technique was developed for attaching Tuckerman optical strain gauges to the sheet without disturbing the strain distribution in the sheet by the method of attachment. This technique was used to explore the strain distribution in the sheet at various loads. The twisting and the bending of the stringers was measured by means of pointers attached to the stringers. The shape of the buckles in the sheet of specimen 6 was recorded at two loads by means of plaster casts. The sheet and the stringer loads at failure are compared with the corresponding loads for five similar panels tested at the Navy Model Basin. A detailed comparison is made between the measured deformation of the buckled sheet and the deformation calculated from approximate theories for the deformation in a rectangular sheet with freely supported edges buckling under end compression advanced by Timoshenko, Frankland, and Marguerre. The measured effective width for the specimens is compared with the effective width given by nine different relations for effective width as a function of the edge stress divided by the buckling stress of the sheet. The analysis of the measured stringer deformation is confined to an application of Southwell's method of plotting deformation against deformation over load. It was concluded that the stringer failure in both specimens were due to an instability in which the stringer was simultaneously twisted and bent as a column.

FORMULAS - BUCKLING - KARMAN↗
NASA NTRS1950

Elastic and plastic buckling of simply supported solid-core sandwich plates in compression

A solution is presented for the problem of the compressive buckling of simply supported, flat, rectangular, solid-core sandwich plates stressed either in the elastic range or in the plastic range. Charts for the analysis of long sandwich plates are presented for plates having face materials of 24s-t3 aluminum alloy, 76s-t6 alclad aluminum alloy, and stainless steel. A comparison of computed and experimental buckling stresses of square solid-core sandwich plates indicates fair agreement between theory and experiment.

Seide, Paul↗
NASA NTRS2012

Stability Analysis of Intertank Formed Skin/Stringer Compression Panel with Simulated Damage

The External Tank (ET) is a component of the Space Shuttle launch vehicle that contains fuel and oxidizer. During launch, the ET supplies the space shuttle main engines with liquid hydrogen and liquid oxygen. In addition to supplying fuel and oxidizer, it is the backbone structural component of the Space Shuttle. It is comprised of a liquid hydrogen (LH2) tank and a liquid oxygen (LOX) tank, which are separated by an Intertank. The Intertank is a stringer-stiffened cylindrical structure with hat-section stringers that are roll formed from aluminum-lithium alloy Al-2090. Cracks in the Intertank stringers of the STS-133 ET were noticed after a November 5, 2010 launch attempt. The cracks were approximately nine inches long and occurred on the forward end of the Intertank (near the LOX tank), along the fastener line, and were believed to have occurred while loading the ET with the cryogenic propellants. These cracks generated questions about the structural integrity of the Intertank. In order to determine the structural capability of the Intertank with varying degrees of damage, a finite element model (FEM) simulating a 1995 compression panel test was analyzed and correlated to test data. Varying degrees of damage were simulated in the FEM, and non-linear stability analyses were performed. The high degree of similarity between the compression panel and the Intertank provided confidence that the ET Intertank would have similar capabilities.

Harper, David W.↗
NASA NTRS1985

Utilization of Space Shuttle External Tank materials by melting and powder metallurgy

The Crucible Melt Extraction Process was demonstrated to convert scraps of aluminum alloy 2219, used in the Space Shuttle External Tank, into fibers. The cast fibers were then consolidated by cold welding. The X-ray diffraction test of the cast fibers was done to examine the crystallinity and oxide content of the fibers. The compressive stress-strain behavior of the consolidated materials was also examined. Two conceptual schemes which would adapt the as-developed Crucible Melt Extraction Process to the microgravity condition in space were finally proposed.

Chern, T. S.↗
NASA NTRS2001

The Effects of Shot and Laser Peening on Fatigue Life and Crack Growth in 2024 Aluminum Alloy and 4340 Steel

Fatigue and crack growth tests have been conducted on 4340 steel and 2024-T3 aluminum alloy, respectively, to assess the effects of shot peening on fatigue life and the effects of shot and laser peening on crack growth. Two current programs involving fixed and rotary-wing aircraft will not be using shot peened structures. Since the shot peening compressive residual stress depth is usually less than the 0.05-inch initial damage tolerance crack size, it is believed by some that shot peening should have no beneficial effects toward retarding crack growth. In this study cracks were initiated from an electronic-discharged machining flaw which was cycled to produce a fatigue crack of approximately 0.05-inches in length and then the specimens were peened. Test results showed that after peening the crack growth rates were noticeably slower when the cracks were fairly short for both the shot and laser peened specimens resulting in a crack growth life that was a factor of 2 to 4 times greater than the results of the average unpeened test. Once the cracks reached a length of approximately 0.1-inches the growth rates were about the same for the peened and unpeened specimens. Fatigue tests on 4340 steel showed that the endurance limit of a test specimen with a 0.002-inch-deep machining-like scratch was reduced by approximately 40 percent. However, if the "scratched" specimen was shot peened after inserting the scratch, the fatigue life returned to almost 100 percent of the unflawed specimens original fatigue life.

Everett, R. A., Jr.↗
NASA NTRS2012

Validation of Lower-Bound Estimates for Compression-Loaded Cylindrical Shells

The traditional approach used in the design of stability critical thin-walled circular cylin- ders, is to reduce unconservative buckling load predictions with an empirical knockdown factor. An alternative analysis-based approach to determine a lower bound buckling load for cylinders under axial compression is to use a lateral perturbation load to create an initial imperfection and determine the buckling load while that load is applied. This paper describes a preliminary e ort to develop a test capability to verify this approach. Results from tests of three aluminum alloy cylinders are described and compared to nite element predictions.

Haynie, Waddy T.↗
DOE OSTI2021

Determining elastic anisotropy of textured polycrystals using resonant ultrasound spectroscopy

Abstract Polycrystalline materials can have complex anisotropic properties depending on their crystallographic texture and crystal structure. In this study, we use resonant ultrasound spectroscopy (RUS) to nondestructively quantify the elastic anisotropy in extruded aluminum alloy 1100-O, an inherently low-anisotropy material. Further, we show that RUS can be used to indirectly provide a description of the material’s texture, which in the present case is found to be transversely isotropic. By determining the entire elastic tensor, we can identify the level and orientation of the anisotropy originated during extrusion. The relative anisotropy of the compressive (c 11 /c 33 ) and shear (c 44 /c 66 ) elastic constants is 1.5% ± 0.5% and 5.7% ± 0.5%, respectively, where the elastic constants (five independent elastic constants for transversely isotropic) are those associated with the extrusion axis that defines the symmetry of the texture. These results indicate that the texture is expected to have transversely isotropic symmetry. This finding is confirmed by two additional approaches. First, we confirm elastic constants and the degree of elastic anisotropy by direct sound velocity measurements using ultrasonic pulse echo. Second, neutron diffraction (ND) data confirm the symmetry of the bulk texture consistent with extrusion-induced anisotropy, and polycrystal elasticity simulations using the elastic self-consistent model with input from ND textures and aluminum single-crystal elastic constants render similar levels of polycrystal elastic anisotropy to those measured by RUS. We demonstrate the ability of RUS to detect texture-induced anisotropy in inherently low-anisotropy materials. Therefore, as many other common materials have intrinsically higher elastic anisotropy, this technique should be applicable for similar levels of texture, providing an efficient general diagnostic and characterization tool.

36 MATERIALS SCIENCE↗
NASA NTRS2015

Hexavalent Chrome Free Coatings for Electronics Electromagnetic Interference (EMI) Shielding Effectiveness (SE) Interim Test Report

Test specimen configuration was provided by Parker Chomerics. The EMI gasket used in this project was Cho-Seal 6503E. Black oxide alloy steel socket head bolts were used to hold the plates together. Non-conductive spacers were used to control the amount of compression on the gaskets. The following test fixture specifications were provided by Parker Chomerics. The CHO‐TP09 test plate sets selected for this project consist of two aluminum plates manufactured to the specifications detailed in CHO­‐TP09. The first plate, referred to as the test frame, is illustrated in Figure 1. The test frame is designed with a cutout in the center and two alternating bolt patterns. One pattern is used to bolt the test frame to the corresponding test cover plate (Figure 2), forming a test plate set. The second pattern accepts the hardware used to mount the fully assembled test plate set to the main adapter plate (Figure 3).

trivalent chromium↗