Search NASA⌕ Search

SEARCH · Search NASA

Results for “AM Powder Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Variations in GARS powder microstructure as a function of powder chemistry and particle size

The properties of metal produced through powder metallurgy depends on the feedstock used. Powders produced via gas atomization reaction synthesis (GARS) are used to produce oxide dispersion strengthened alloys. The desired powder size range can vary for each consolidation technique. However, powder microstructure also can vary with powder particle size, which in turn can impact the microstructure and properties of the consolidated parts. In this study, GARS powders are characterized via inductively coupled plasma mass spectroscopy, inert gas fusion, and high-resolution x-ray diffraction to determine variations in elemental and phase compositions. Transmission electron microscopy was used to understand microstructure variations as a function of chemistry and size. Across the three batches tested intermetallic content was 0.73–1.35 wt% in the 0-20 μm powder batch and increased to 2.46–3.80 wt% in the coarse 45-106 μm batch. Across all batches, volume percent of surface oxidation decreased with powder diameter, with volume percents within the range of 0.75–1.2 % across 10 μm powder particles, and below 0.4 % across coarse powder particles approximately 100 μm in diameter. These observations were supported by inert gas fusion measurements. However, the oxide layer was thicker in coarse powder particles due to a slower cooling rate. Increasing oxygen content in atomization gas to 2000 ppm and adding yttrium increased both the surface oxidation content and yttrium intermetallic content. Lastly, intermetallic phases within the powder coarsened with powder size. Intermetallic morphology changed from fine spherical intermetallic and columnar dendritic growth to a cellular structure with finer spherical intermetallic, to coarse irregular intermetallic and intermetallic along grain boundaries as a result of slower cooling rate and solidification rate in coarse powder particles. Furthermore, the addition of zirconium does not appear to significantly change intermetallic morphology, but the composition changed from a Y-Fe rich intermetallic to a Y-Zr-Fe intermetallic.

42 ENGINEERING↗
DOE OSTI2021

Flow behavior characterization of biomass Feedstocks

With the advancement of renewable energy, the processing and handling of biomass feedstocks has drawn enormous research interest. The key to economically viable and operationally reliable biomass handling processes involves a complete understanding of the flow behavior of different feedstocks as functions of the inherent critical material properties environmental conditions, and critical processing parameters. This review introduces the basic principles and methods in bulk solids flow and highlights recent efforts to understand the flow behavior of biomass feedstocks. The effects of inherent properties, environmental parameters, and handling equipment on the flow behavior of biomass feedstocks are presented. Particle size, shape, moisture, consolidation stress, temperature, storage time at rest, chemical treatment, and the material and geometry of the handling equipment all substantially influence biomass flowability. The limitations of current studies and the potential methods to overcome them are presented. Finally, an outlook for future research effort is provided, with proposed opportunities for improving the characterization of biomass flow.

Bulk solids testing↗
DOE OSTI2026

Characterization of ceramic fuel powder packing fractions to support INFLUX

Triply periodic minimal surface (TPMS)-based structures show marked potential in novel nuclear reactor fuel designs, as their high surface area-to-volume ratio increases the efficiency of heat transfer out of the fuel, enabling safer, more innovative reactor designs. This milestone report addresses the role of dUO 2 powder processing route on the fill behavior of TPMS-based cladding shells to understand and advance the feasibility of manufacturing TPMS-based nuclear fuel forms. dUO 2 powder was processed through either a dry granulation route, varying consolidation pressure, or through milling, varying milling time, milling method and milled size distribution. The lowest tapped bulk densities (TBD), but best powder flowabilities, were obtained when testing unprocessed dUO 2 powder which was prone to self-agglomeration and formed low-density spheroids. The highest TBD and lowest flowabilities were obtained when using powder produced by hammer-milling dUO 2 powder to pass through a 200-mesh sieve, which led to particles with angular morphologies. Powder produced by dry granulation exhibited TBD that varied according to the consolidation pressure used to form the initial pellets and exhibited improved flowabilities when compared to hammer-milled material. Because of the large span of granule sizes formed as well as the irregular shape associated with the granules, a packing fraction of 0.69 was achieved, exceeding the analytical solution for random close packing of mono-sized spheres. TPMS polymer shells were loaded with unprocessed, granulated, and hammer-milled dUO 2 powders, and their qualitative packing behaviors were analyzed using x-ray computed tomography (xCT). TBDs calculated after loading TPMS polymer shells were 10-20% lower when compared to tapped bulk density measurements taken in a glass graduated cylinder, indicating a non-trivial impact on the tapped bulk density of either the TPMS channel size, TPMS channel surface material, powder cohesiveness, or a combination of the two parameters. A metallic zircaloy-4 TPMS shell will be loaded with hammer-milled dUO 2 powder upon receipt of the shell from Oak Ridge National Laboratory (ORNL) and shipped to Idaho National Labs (INL) for subsequent hot isostatic pressing (HIP) densification experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Fatigue of laser powder bed fusion processed 17-4 stainless steel using prior process exposed powder feedstock

The rapid pace of development seen in the metal additive manufacturing (AM) process of laser powder-bed fusion (LPBF) requires in-step advances in processes qualification to enable full-scale adoption. This particularly applies to quantifying how powder feedstock conditions impact end-component quality. Here this study examines how in-machine 17-4 stainless steel powder feedstocks are affected by prior LPBF processes, and how these effects impact subsequent builds. Examinations of powder morphology, chemistry, flowability, and rheology were conducted to characterize the powder conditions. The resultant effects of powder feedstock condition on produced component quasi-static tensile and high-cycle fatigue properties were analyzed. Fatigue life was analyzed using a reliability modeling approach that enabled a robust statistical comparison of life. Powder characteristics were found to evolve with powder exposure to prior LPBF processes, particularly in the extremes of powder size distribution and measures of bulk flow. No significant effects of these changes on tensile properties were observed. Reliability modeling methods, including the lognormal and Weibull distributions as well as the empirical survival function, are shown to be effective tools for modeling fatigue variability in LPBF manufactured components. Through these tools, fatigue life was found to be invariant with changes in powder condition.

42 ENGINEERING↗
DOE OSTI2023

Effects of particle size, shape and loading rate on the normal compaction of an advanced granular ceramic

Compaction behavior of granular materials is influenced by strain rate, particle size, and shape. In this report, boron carbide powders with different particle sizes under uni-axial strain conditions are studied using quasi-static compression, dynamic Kolsky bar experiments and normal plate impact. A rounded powder is compacted to investigate the effect of particle shape. The normal plate impact technique is an excellent tool in characterization of powder compaction behavior up to strain rates of ~10 5 s -1 . From our experiments, granular boron carbide shows a highly compressible behavior with significant volume compaction. Constitutive responses are obtained for four powders. Particle fracture is identified as key deformation mechanism. Dynamic loading introduces more particle fragmentation than quasi-static loading. Morphological characterization of particle shapes shows that the deformation from powder compaction alters the particle shape distribution, which is also rate-dependent. Particle size, shape and strain rate effects on the normal stress are discussed accordingly.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of Properties of Laser Powder Bed Fusion 3D-Printed Inconel 718 for Centrifugal Turbomachinery Applications

Here, this paper presents the results of a comprehensive effort to characterize the properties of Inconel 718 produced by a form of laser powder bed fusion (LPBF) additive manufacturing (AM) or 3D-printing, subsequently subjected to hot isostatic pressing (HIP) and heat treatment according to standards F3055-14a and AMS 5663, respectively. Material property data, while broadly available for traditional Inconel 718 presentations (e.g. forgings or castings), is currently lacking for the 3D-printed material. It is expected that while limited in size, the experimental data sets presented provide sufficient information to glean the capability of LPBF Inconel 718. These include: 1) Chemical composition, electron backscatter diffraction (EBSD), and x-ray energy dispersive spectroscopy (XEDS) characterization of 3D-printed material structure; 2) Tensile properties — 0.2% yield stress, ultimate stress, modulus of elasticity, and elongation to failure — based on 108 samples, as functions of temperature and sample print orientation; 3) Creep rupture data including the Larson-Miller parameter, based on 21 samples; and 4) High cycle fatigue data based on 21 samples as a function of temperature. Results are compared to available standards and/or data for forged, cast, and other AM Inconel 718. A key observation of this study, based on the EBSD results, is that while the material appears to approach full recrystallization following heat treatment, there is a detectable fraction of the material that does not fully recrystallize, resulting in a material with mechanical properties (e.g. yield stress, creep rupture) measurably lower than those of forgings, but higher than those of castings.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1995

Effect of Nb2O5 and V2O5 addition on the superconducting properties of YBa2Cu3O(y) thin films

The effect of Nb2O5 and V2O5 addition on the superconducting properties and microstructure of YBa2Cu3O(y) has been studied in thin films. Polycrystalline targets for laser ablation were prepared by mixing high purity V2O5 or Nb2O5 powders with a well characterized YBa2Cu3O(y) powder in the range 0 to 4 wt percent by solid state reaction method. Thin films (approximately 1500 A thickness) of the above targets were grown on (100) SrTiO3 (STO) and (100) LaAlO3 (LAO) substrates at 700 C temperature by pulsed laser deposition (PLD) technique. In the case of Nb2O5 addition we have noticed an increase in J(sub c) up to 0.5 wt percent and higher additive concentration (greater than 0.5 wt percent) have degraded the superconducting properties. However, in the case of V2O3 addition, there is an improvement in current density and microstructural properties up to 1 wt percent and the superconducting properties degrade for concentrations greater than 1 wt percent. The best J(sub c) for 0.5 wt percent of Nb2O5 added YBCO thin film is 1.6 x 10(exp 6) A/sq cm and for that of V2O5 added sample is 3.4 x 10(exp 6) A/sq cm at 77 K as compared to the pure YBa2Cu3O(y) (YBCO) film J(sub c) (1.2 x 10(exp 6) A/sq cm) observed on STO substrates. The reason for improvement in J(sub c) and microstructural properties in the case of V2O5 addition could be due to the low melting of V2O5 (690 C) which can act as a very good surfactant during deposition. Over all, we have realized that Nb2O5 addition or V2O5 addition to YBCO have shown significant improvement over the undoped YBa2Cu3O(7-x) films grown under identical conditions.

Srinivas, S.↗
NASA NTRS2017

Surveying Clay Mineral Diversity in the Murray Formation, Gale Crater, Mars

One of the primary science goals of Mars Science Laboratory (MSL) is to investigate layered clay mineral-bearing deposits outcropping in the lower NW slopes of Aeolis Mons (Mt. Sharp) detected from orbit. Martian clay mineral-bearing layered rocks are of particular interest because they are potential markers of sedimentary deposits formed in habitable aqueous environments. The CheMin X-ray diffraction (XRD) instrument aboard MSL has documented clay minerals in various drill samples during its traverse of Gale Crater's floor and ascent of Mt. Sharp. Previously, the high concentrations of clay minerals (approximately 20 wt.%) detected in drill powders of mudstone (Sheepbed member) at Yellowknife Bay (YKB) allowed their detailed characterization. Drill powders recovered from lacustrine mudstones of the Sheepbed member at YKB contain smectite clay minerals. Based on the position of 02l reflections in XRD patterns, which serve as an indicator of octahedral occupancy, the smectites are Fe-bearing, trioctahedral species analogous to ferrian saponites from terrestrial deposits. The smectites are thought to have been formed through a process of isochemical aqueous alteration of detrital olivine close to the time of sediment deposition under anoxic to poorly oxidizing conditions. The clay minerals are key indicators that the lake waters were benign and habitable at the time. Clay minerals were detected at other locations during MSL's traverse, including samples from the Pahrump Hills, but lower abundances and overlapping peaks from crystalline phases in XRD patterns hamper in-depth analysis.

Bristow, T. F.↗
DOE OSTI2019

Development and Mechanical Properties of In Situ Al{sub 3}Ti-Reinforced Nanostructured AA6061 via Mechanical Alloying

Mechanical alloying (MA) was used to disperse 10 wt.% titanium powder in AA6061 powder. The resultant powder was degassed, and differential scanning calorimetry was performed to determine the temperature for formation of titanium aluminide (Al{sub 3}Ti). The MA powder was characterized by field emission scanning electron microscopy, x-ray diffraction (XRD) and transmission electron microscopy (TEM). Subsequently, the MA powder was consolidated by spark plasma sintering (SPS) at 500 °C under a pressure of 50 MPa. XRD and x-ray energy-dispersive spectroscopy of spark plasma sintered compact revealed in situ formation of Al{sub 3}Ti. TEM micrographs of spark plasma sintered sample exhibited Al nanograins (average size 50 nm) in the AA6061 matrix along with the dispersed Al{sub 3}Ti (average size 200 nm). Hardness, yield strength and compressive strength of the SPSed samples were also evaluated and compared with AA6061.

36 MATERIALS SCIENCE↗
NASA NTRS2005

Fabrication and Characterization of High Temperature Resin/Carbon Nanofiber Composites

As part of ongoing efforts to develop multifunctional advanced composites, blends of PETI-330 and carbon nanofibers (CNF) were prepared and characterized. Dry mixing techniques were employed and the effect of CNF loading level on melt viscosity was determined. The resulting powders were characterized for degree of mixing, thermal and rheological properties. Based on the characterization results, samples containing 30 and 40 wt% CNF were scaled up to approx.300 g and used to fabricate moldings 10.2 cm x 15.2 cm x 0.32 cm thick. The moldings were fabricated by injecting the mixtures at 260-280 C into a stainless steel tool followed by curing for 1 h at 371 C. The tool was designed to impart high shear during the injection process in an attempt to achieve some alignment of CNFs in the flow direction. Moldings were obtained that were subsequently characterized for thermal, mechanical and electrical properties. The degree of dispersion and alignment of CNFs were investigated using high-resolution scanning electron microscopy. The preparation and preliminary characterization of PETI-330/CNF composites will be discussed.

Ghose, Sayata↗
DOE OSTI2021

Effect of Composition on the Phase Structure and Magnetic Properties of Ball-Milled LaFe11.71-xMnxSi1.29H1.6 Magnetocaloric Powders

Magnetocaloric alloys are an important class of materials that enable non-vapor compression cycles. One promising candidate for magnetocaloric systems is LaFeMnSi, thanks to a combination of factors including low-cost constituents and a useful curie temperature, although control of the constituents’ phase distribution can be challenging. In this paper, the effects of composition and high energy ball milling on the particle morphology and phase stability of LaFe11.71-xMnxSi1.29H1.6 magnetocaloric powders were investigated. The powders were characterized with optical microscopy, dynamic light scattering, X-ray diffraction (XRD), and differential scanning calorimetry (DSC). It was found that the powders retained most of their original magnetocaloric phase during milling, although milling reduced the degree of crystallinity in the powder. Furthermore, some oxide phases (<1 weight percent) were present in the as-received and milled powders, which indicates that no significant contamination of the powders occurred during milling. Finally, the results indicated that the Curie temperature drops as Fe content decreases (Mn content increases). In all of the powders, milling led to an increase in the Curie temperature of ~3–6 °C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Synthesis and Characterization of Silicon Carbide Ceramic Composites with CeO 2 Powder

This study pioneers the fabrication and characterization of silicon carbide (SiC) containing cerium dioxide (CeO 2 ). CeO 2 powder was tested as a surrogate for actinide oxide waste forms such as uranium dioxide (UO 2 ) and plutonium dioxide (PuO 2 ). Several syntheses were evaluated with varying amounts of preceramic polymer (SMP-10 resin) and CeO 2 containing either SiC fiber, carbon fiber, or no fibers. Scanning electron microscopy (SEM) was used to characterize morphology and compositional differences, and energy-dispersive x-ray spectroscopy (EDS) was used to provide semiquantitative elemental analysis. In addition, each sample was characterized by density, powder x-ray diffraction (pXRD), and Raman spectroscopy. Samples containing nearly more than four times CeO 2 powder than SMP-10 resin by mass had the best properties. This research establishes a unique synthesis for SiC containing high concentrations of CeO 2 powder to illustrate how it may be managed as a potential waste form.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Synthesis and Characterization of Natural Nano-hydroxyapatite Derived from Turkey Femur-Bone Waste

Hydroxyapatite (HAp) is a bioactive and vital material which has found many applications in the biomedical and clinical fields. This bio-ceramic powder can be synthesized via different bio-waste materials. In this study, the production of natural nanohydroxyapatite was produced through calcination of untreated turkey femur-bone waste powder at 850 °C followed by ball milling the powder. The obtained powder was characterized using X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR) analysis. The morphology, size, and elemental composition of obtained turkey hydroxyapatite (THA) particles were investigated by scanning electron microcopy (SEM), transmission electron microcopy (TEM), and energy dispersive spectroscopy (EDS) analysis, in which the average particle size of ball milled THA was found to be about 85 nm with a Ca/P ratio of 1.63. The powder was then cold pressed and later sintered at 850, 950, 1050, and 1150 °C to evaluate its mechanical properties in terms of compressive strength and hardness. The results revealed that the strength and hardness of the samples increased by increasing the sintering temperature up to 1150 °C. Finally, the maximum values of hardness and compressive strength of the sintered THA were obtained at 1150 °C (37.44 MPa and 3.2 GPa, respectively).

60 APPLIED LIFE SCIENCES↗
NASA NTRS1982

An investigation of adhesive/adherend and fiber/matrix interactions. Part A: Surface characterization of titanium dioxide, titantium and titanium 6% Al to 4% V powders: Interaction with water, hydrogen chloride and polymers

The titanium dioxide surface is discussed. Polymer adhesive are also discussed. Titanium powders are considered. Characterization techniques are also considered. Interactions with polymers, water vapor, and HCl are reported. Adsorbents are characterized.

Siriwardane, R. V.↗
DOE OSTI2020

Synthesis and flash sintering of (Hf 1-x Zr x )B 2 solid solution powders

(Hf 1-x Zr x )B 2 solid solution powders were synthesized by two methods. First, solution-based processing of HfCl 4 , ZrCl 4 , sucrose, and H 3 BO 3 was conducted followed by heat treatment in Argon to carry out the carbothermal reduction (CTR) reaction to form the diboride powders. Alternatively, in the so-called borohydride reduction (BHR) method, HfCl 4 , ZrCl 4 and NaBH 4 were mixed in an Argon glove box followed by heat treatment in Argon at 700-1500°C. The synthesized powders were characterized by XRD, SEM, TEM, EDS, and TGA, and the influence of different parameters such as starting composition, heat treatment temperature and time on products characteristics were revealed. Both CTR and BHR solid solution powders were then consolidated within ~5 min in a homemade flash sintering (FS) setup. Here, the composition, microstructure, hardness, and thermal-oxidation properties of flash sintered ceramics were characterized, and the implication of this study and directions for future research were discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

From ammonium Hexahalorhenates(IV) to nanocrystalline rhenium metal: A combined thermal, diffraction and microscopic analysis

Rhenium metal powder is a material of industrial importance. Several industrial and laboratory methods have been developed for the preparation of ultrafine Re metal powder and nanoparticles. The present study provides a better understanding of the characteristic and formation of Re metal powder from the decomposition of (NH4)2ReX6 salt (X = F, Cl, Br, I) at high temperature in inert atmosphere. Such analysis resulted in the formation of nanocrystalline Re metal as characterized by powder XRD. Williamson-Hall, Scherrer, and Williamson-Smallman methods were employed to study the effect of crystallize size, lattice strain, and dislocation density as analyzed from powder XRD peak broadening. Here, the morphology and composition of the metal were analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Structural changes during milling of aluminum oxide powders

The mechanical activation of four fused corundum powders and a calcined Al2O3 powder was studied. The milled powders were characterized by their structural properties, crystallite size, and lattice distortions. Structural changes during milling, detected by X-ray line broadening analysis, gave information about the enhanced activity of the powders caused by the lattice distortions and by the decreasing crystallite size during milling. The structural changes during milling, under the same milling conditions, can be quite different for the same ceramic material, but with different characteristics in the as received state.

Ziepler, G.↗
DOE OSTI2026

A LASER POWDER BED FUSION ADDITIVE MANUFACTURING CHARACTERIZATION APPROACH AND DATASET HIGHLIGHTING IMPLICATIONS FOR CROSS-PLATFORM PERFORMANCE CONSISTENCY

Additive Manufacturing (AM) has remained a rapidly growing technology over the past decade, which affords many benefits. However, there is one main hinderance to widespread adoption: Products produced on one Laser Powder Bed Fusion (LPBF) AM system can vary in mechanical performance from those produced on another system. This is due to the fact that while LPBF AM system is producing a product’s shape, it is also producing the product’s material. Due to the complex and dynamic nature of LPBF, items fabricated on one system can be different in terms of dimensions, microstructure and quality compared to items fabricated on a different make or model system. This lack of cross-platform performance consistency makes widespread adoption challenging. This work was created to help understand the variation between different Laser Powder Bed Fusion (LPBF) Additive Manufacturing (AM) systems across different manufacturers, models, and users, and to provide insight into how to ensure product consistency regardless of system selection.

36 MATERIALS SCIENCE↗