Search NASA⌕ Search

SEARCH · Search NASA

Results for “Advanced Casting System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Major Modification Determination Process Utilized for Proposed Idaho National Laboratory Projects

Over the past three years, several new projects with the potential for major modifications to existing facilities have been considered for implementation at the Idaho National Laboratory (INL). These projects were designated to take place in existing nuclear facilities with existing documented safety analyses. 10 CFR 830.206 requires the contractor for a major modification to a Hazard Category 1, 2, or 3 nuclear facility to obtain Department of Energy (DOE) approval for the nuclear facility design criteria to be used for preparation of a preliminary documented safety analysis (PDSA), as well as creation and approval of the PDSA, before the contractor can procure materials or components or begin construction on the project. Given the significant effort and expense of preparation and approval of a PDSA, a major modification determination for new projects is warranted to determine if the rigorous requirements of a major modification are actually required. Furthermore, performing a major modification determination helps to ensure that important safety aspects of a project are appropriately considered prior to modification construction or equipment procurement. The projects considered for major modification status at the INL included: treatment and packaging of unirradiated, sodium-bonded highly enriched uranium (HEU) fuel and miscellaneous casting scrap in the Materials and Fuels Complex (MFC) Fuel Manufacturing Facility (FMF); post irradiation examination of Advance Fuel Cycle Initiative (AFCI) fuel in the MFC Analytical Laboratory (AL); the Advanced Test Reactor (ATR) gas test loop (GTL); and the hydraulic shuttle irradiation system (HSIS) at ATR. The major modification determinations for three of the proposed projects resulted in a negative major modification. On the other hand, the major modification determination for the GTL project concluded that the project would require a major modification. This paper discusses the process, methods, and considerations used by the INL for the four major modification determinations. Three of the four major modification determinations discussed herein were completed using the guidance specified in the draft of DOE STD-1189, “Integration of Safety into the Design Process.” DOE-STD-1189 was released as a draft document in March 2007 and provides guidance for integrating safety considerations into the early design activities for constructing new facilities or making modifications to existing nuclear facilities. The fourth major modification determination was prepared prior to the existence of DOE STD-1189 and was evaluated solely by the definition of a major modification given in 10 CFR 830.206. For all four projects, consideration was given to: • Facility hazard categorization change and material inventory • Facility footprint change with the potential to adversely affect credited safety function • New or changed processes resulting in a change to the safety basis • The use of new technology or equipment not approved for use in the facility • The need for new or revised safety basis controls • Hazards not previously evaluated in the safety basis.

10 CFR 830↗

Thick Electrode Design for Facile Electron and Ion Transport: Architectures, Advanced Characterization, and Modeling

The demand for lithium ion batteries continues to expand for powering applications such as portable electronics, grid-scale energy storage, and electric vehicles. As the application requirements advance, the innovation of lithium ion batteries toward higher energy density and power output is required. Along with the investigation of new materials, an important strategy for increasing battery energy content is to design electrodes with high areal loading to minimize the fraction of nonactive materials such as current collectors, separators, and packaging components, resulting in significant gains in energy content and the reduction of the system-level cost. However, the adoption of thick high areal loading electrodes has been impeded by sluggish charge transport and mechanical instability. With conventional slurry cast electrodes, battery function significantly deteriorates with increases in electrode thickness due to high cell polarization and the incomplete utilization of active materials. Thus, a consideration of approaches that facilitate an understanding and eventual adoption of high-loading electrodes is warranted to enable the deliberate advancement of next-generation batteries. Herein, this Account considers three aspects critical to the science and technology of thick high-loading electrodes. The first discussion covers recent approaches to the design and fabrication of high-loading electrodes. Ensuring electrical contact throughout the electrode is accomplished through the manipulation of conductive additives or using a conductive scaffold within the electrode. Ion transport can be facilitated through electrode design and fabrication approaches that deliberately control the electrode porosity and tortuosity. Second, advanced characterization methodologies are presented as the ability to determine the origins of transport limitations provide the insight needed to deliberately approach future designs. Spectroscopic and diffraction methods have been used to characterize the 2D and 3D pore structure and composition of the electrodes. Furthermore, operando methods that yield spatially and temporally resolved information regarding the progression of the electrochemical reaction are highlighted. The third aspect considered is the utilization of modeling. Physically based continuum models linked with the results of experimental characterization have been demonstrated and then allow the rapid simulation of a variety of deliberate electrode designs and their impacts on functional electrochemistry. Variables relevant to the designs can be tested by the model under a series of use conditions to identify those of most promise for a specific application. Finally, an outlook on future opportunities for high-loading battery electrode research is provided to inform and entice practitioners in the field to pursue these important directions of inquiry.

25 ENERGY STORAGE↗

Additive Manufacturing Advances to Facilitate Novel Robot and Remote System Construction

Additive manufacturing (AM) in both polymer and metal has advanced to the point where it can substantially facilitate robot and remote system design and implementation. While AM is not a panacea to fix bad design concepts, properly used AM can create features and capabilities otherwise not possible in machined or cast products. AM design rules are still being developed and must be applied differently based on the process and purpose of the final component, but progress is being made in practical implementation. Polymer-based AM has been available commercially for quite some time and is regularly used to facilitate prototyping and test fitting of parts later to be fabricated in metal or to produce low production quantity parts that do not require high structural strength. However Oak Ridge National Laboratory (ORNL) has pioneered large scale polymer additive manufacturing with sufficient strength to print a car and frame, a small house, a “wet” submarine, and tooling to mold wind generator blades. While polymer processes use a variety of materials, all polymer printers basically lay down a heated extruded bead of a certain width and height. Print resolution is based on the deposition rate of the printer. The larger the deposition rate, the lower the print resolution. Large scale polymer builds often rely on post processing (machining) to provide a smooth finish to the part surface.Metal printing processes are much more diverse than polymer print processes. Electron beam (ebeam), laser, and binder jet are common methods to fuse metal powder-based systems. Metal powder spray can be done with laser or plasma. While metal powder systems produce high definition parts, part size is limited. Larger parts are currently done with wire feed systems based on laser or arc (metal inert gas (MIG) or tungsten inert gas (TIG)) processes. Part definition decreases, but part size can be on the order of tens of cubic feet and hundreds of pounds.Two implementation examples are presented in this paper to illustrate the possibilities and to identify issues that remain. A dual arm hydraulic manipulator was printed in titanium using the ebeam process. All hydraulics and electrical cabling passageways were printed into the manipulator; there are no external hoses or cables. The distal link of an excavator arm was printed using a wire feed metal inert gas (MIG) process. The excavator was then used for digging as part of an equipment exposition validating the metallurgy of the printed part.

Nycz, Andrzej↗

Additive Manufacturing Advances to Facilitate Novel Robot and Remote System Construction

Additive manufacturing (AM), in both polymer and metal, has advanced to the point where it can substantially facilitates robot and remote system design and implementation. While AM is not a panacea to fix bad design concepts, properly used AM can creates features and capabilities otherwise not possible in machined or cast products. AM design rules are still being developed and must be applied differently based on the process and purpose of the final component, but progress is being made in practical implementation. Polymer-based AM has been commercially available commercially for quite some time and is regularly used to facilitatefor prototyping and test fitting of parts later to be before they are fabricated fromin metal or to produced in low production quantity parts that do not require high structural strength. Metal printing processes are more diverse than polymer print processes. Both polymer and metal printing systems can be used to make parts or complete systems for robotics. Two implementation examples thato illustrate the possibilities and to identify issues that remain in metal printing are: a dual arm hydraulic manipulator and a distal link of an excavator arm. The dual arm hydraulic manipulator was printed in titanium using an e-beam fusing process. All hydraulics and electrical cabling passageways were printed into the manipulator; there are no external hoses or cables. The distal link of an excavator arm was printed using a wire-fed metal inert gas process. The excavator was then used for digging as part of an equipment exposition validating the structural integrity of the printed part.

Noakes, Mark↗

Development of Self-Assembly Supports Enabling Transformational Membrane Performance for Cost-Effective Carbon Capture

This final technical report describes work conducted by Membrane Technology and Research, Inc. (MTR) for the U.S. Department of Energy (DOE), National Energy Technology Lab (NETL) on the development of membranes with transformational performance for carbon capture under award number DE-FE0031596. The work was performed from June 1, 2018 through May 31, 2024. For more than a decade, MTR has worked in partnership with DOE to develop an innovative membrane-based CO 2 capture process. This effort has included the first test of membrane modules with coal-fired flue gas at the Arizona Public Services (APS) Cholla plant in 2010; the accumulation of >11,000 hours of flue gas operation for Polaris modules on a bench-scale 1 tonne/day (TPD) system at the National Carbon Capture Center (NCCC); scale-up of first-generation (Gen-1) Polaris to a 20 TPD small pilot system, and successful operation of this system on a flue gas slipstream at NCCC and in integrated boiler testing at Babcock & Wilcox (B&W). Through continued development efforts, a second-generation (Gen-2) version of the Polaris membrane has been scaled-up to pilot production. This membrane offers 70% higher CO 2 permeance with similar selectivity to the base case Polaris. MTR also developed planar modules designed specifically for the low-pressure, high-volumetric flow rate process conditions of flue gas operation. These new modules have significantly lower pressure-drop values compared to the type originally used (spiral-wound modules), which results in significant energy savings. The goal of the work described in this report was to improve on the Polaris Gen-2 membrane with the ultimate aim to reduce the cost of carbon capture. The majority of the effort was to develop improved support membranes for the multi-layer composite structure of MTR’s Polaris membrane. Earlier work at MTR had identified the support structure as limiting membrane permeances, not because the support itself represents a permeation resistance, but because the distribution of pores at the surface of the support imposes a geometric restriction to diffusion in the layers above it. Support membranes were prepared from a range of polymers, including commercially available block copolymers and a custom synthesized block copolymer alternative. The best support membranes developed in this project reduced the geometric restriction by a factor of two to three. These supports then were used to produce Polaris composite membranes with improved permeances. The second topic was to create a high-selectivity version of the Polaris membrane. The high-selectivity version uses a novel selective polymeric material and high selectivities were confirmed in experiments at MTR. The material is not easily made into very thin films. Consequently, the permeances are significantly lower than the Polaris Gen-2 membrane. The utility of this membrane is therefore limited to the carbon dioxide purification step that produces liquid CO 2 . A Technical and Economic Analysis (TEA) was performed for a carbon capture system that uses both advanced membrane types. The TEA shows the novel advanced membranes reduce the cost of capture by 10%, from $63.32/tonne CO 2 to $56.90/tonne CO 2 (2022 USD). Most of the development work was carried out with laboratory-scale casting and coating equipment. A number, but not all, of the improvements identified have been implemented on commercial-scale manufacturing equipment. The focus of future work at MTR is to incorporate the advancements made into the Polaris membrane manufacturing process.

01 COAL, LIGNITE, AND PEAT↗

High-Performance AEM LTE with Advanced Membranes, Ionomers and PGM-Free Electrodes

Alkaline low temperature electrolysis (LTE) systems enjoy several potential advantages over acid-based LTE systems including facile oxygen evolution reaction (OER) kinetics and electrodes that can use little to no platinum group metals (PGM). The polymer membranes and membrane electrode assembly (MEA) structures going into alkaline electrochemical systems have seen significant advances in recent years. The objective of this project is to combine state-of-the-art alkaline polymer electrolyzer components into one optimized membrane electrode assembly (MEA) system to achieve DOE low temperature electrolysis (LTE) goals. The benefit of individual component advances cannot be fully appreciated until all aspects and components of the MEA are working at an equally high level of performance. New electrode fabrication methods were developed where solvent cast catalyst/ionomer solutions were used in place of insoluble ionomers to significantly improve adhesion. The membranes were improved in terms of durability and mechanical properties. The OER and HER catalysts were improved and made more durable.

08 HYDROGEN↗

An AC modulated near infrared gain calibration system for a “Violin-Mode” transimpedance amplifier, intended for advanced LIGO suspensions

The background to this work was a prototype shadow sensor, which was designed for retro-fitting to an advanced LIGO (Laser Interferometer Gravitational wave Observatory) test-mass/mirror suspension, in which a 40 kg test-mass/mirror is suspended by four approximately 600 mm long by 0.4 mm diameter fused-silica suspension fibres. The shadow sensor comprised a LED source of Near InfraRed (NIR) radiation, and a “tall-thin” rectangular silicon photodiode detector, which together were to bracket the fibre under test. The photodiode was positioned so as to be sensitive (primarily) to transverse “Violin-Mode” vibrations of such a fibre, via the oscillatory movement of the shadow cast by the fibre, as this moved across the face of the detector. In this prototype shadow sensing system the photodiode was interfaced to a purpose-built transimpedance amplifier, this having both AC and DC outputs. A quasi-static calibration was made of the sensor’s DC responsivity, i.e., incremental rate of change of output voltage versus fibre position, by slowly scanning a fused-silica fibre sample transversely through the illuminating beam. The work reported here concerns the determination of the sensor’s more important AC (Violin-Mode) responsivity. Recognition of the correspondence between direct AC modulation of the source, and actual Violin-Mode signals, and of the transformative role of the AC/DC gain ratio for the amplifier, at any modulation frequency, f, resulted in the construction of the AC/DC calibration source described here. A method for determining in practice the transimpedance AC/DC gain ratio of the photodiode and amplifier, using this source, is illustrated by a specific numerical example, and the gain ratio for the prototype sensing system is reported over the frequency range 1 Hz–300 kHz. In fact, a maximum DC responsivity of 1.26 kV.m{sup −1} was measured using the prototype photodiode sensor and amplifier discussed here. Therefore, the measured AC/DC transimpedance gain ratio of 922.5 for this sensor, at 500 Hz, translated into a maximum Violin-Mode (AC) responsivity of (1.16 ± 0.05) MV m{sup −1}, at that frequency.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Quasi-static displacement calibration system for a “Violin-Mode” shadow-sensor intended for Gravitational Wave detector suspensions

This paper describes the design of, and results from, a calibration system for optical linear displacement (shadow) sensors. The shadow sensors were designed to detect “Violin-Mode” (VM) resonances in the 0.4 mm diameter silica fibre suspensions of the test masses/mirrors of Advanced Laser Interferometer Gravitational Wave Observatory gravitational wave interferometers. Each sensor illuminated the fibre under test, so as to cast its narrow shadow onto a “synthesized split photodiode” detector, the shadow falling over adjacent edges of the paired photodiodes. The apparatus described here translated a vertically orientated silica test fibre horizontally through a collimated Near InfraRed illuminating beam, whilst simultaneously capturing the separate DC “shadow notch” outputs from each of the paired split photodiode detectors. As the ratio of AC to DC photocurrent sensitivities to displacement was known, a calibration of the DC response to quasi-static shadow displacement allowed the required AC sensitivity to vibrational displacement to be found. Special techniques are described for generating the required constant scan rate for the test fibre using a DC motor-driven stage, for removing “jitter” at such low translation rates from a linear magnetic encoder, and so for capturing the two shadow-notch signals at each micrometre of the test fibre's travel. Calibration, across the four detectors of this work, gave a vibrational responsivity in voltage terms of (9.45 ± 1.20) MV (rms)/m, yielding a VM displacement sensitivity of (69 ± 13) pm (rms)/√Hz, at 500 Hz, over the required measuring span of ±0.1 mm.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Novel Power Electronics Three-Dimensional Heat Exchanger: Preprint

Electric drive systems for vehicle propulsion enable technologies critical to meeting challenges for energy, environmental, and economic security. Enabling cost-effective electric drive systems requires reductions in inverter power semiconductor area. As critical components of the electric drive system are made smaller, heat removal becomes an increasing challenge. In this paper, we demonstrate an integrated approach to the design of thermal management systems for power semiconductors that matches the passive thermal resistance of the packaging with the active convective cooling performance of the heat exchanger. The heat exchanger concept builds on existing semiconductor thermal management improvements described in literature and patents, which include improved bonded interface materials, direct cooling of the semiconductor packages, and double-sided cooling. The key difference in the described concept is the achievement of high heat transfer performance with less aggressive cooling techniques by optimizing the passive and active heat transfer paths. An extruded aluminum design was selected because of its lower tooling cost, higher performance, and scalability in comparison to cast aluminum. Results demonstrated a heat flux improvement of a factor of two, and a package heat density improvement over 30%, which achieved the thermal performance targets.

30 DIRECT ENERGY CONVERSION↗

Metallic Fast Reactor Fuel Fabrication for Global Nuclear Energy Partnership

Fast reactors are once again being considered for nuclear power generation, in addition to transmutation of long-lived fission products resident in spent nuclear fuels. This re-consideration follows with intense developmental programs for both fuel and reactor design. One of the two leading candidates for next generation fast reactor fuel is metal alloys, resulting primarily from the successes achieved in the 1960s to early 1990s with both the experimental breeding reactor-II and the fast flux test facility. The goal of the current program is to develop and qualify a nuclear fuel system that performs all of the functions of a conventional, fast-spectrum nuclear fuel while destroying recycled actinides, thereby closing the nuclear fuel cycle. In order to meet this goal, the program must develop efficient and safe fuel fabrication processes designed for remote operation. This paper provides an overview of advanced casting processes investigated in the past, and the development of a gaseous diffusion calculation that demonstrates how straightforward process parameter modification can mitigate the loss of volatile minor actinides in the metal alloy melt.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

TH-CD-201-05: Characterization of a Novel Light-Collimating Tank Optical-CT System for 3D Dosimetry

Purpose: Comprehensive 3D dosimetry is highly desirable for advanced clinical QA, but costly optical readout techniques have hindered widespread implementation. Here, we present the first results from a cost-effective Integrated-lens Dry-tank Optical Scanner (IDOS), designed for convenient 3D dosimetry readout of radiochromic plastic dosimeters (e.g. PRESAGE). Methods: The scanner incorporates a novel transparent light-collimating tank, which collimates a point light source into parallel-ray CT geometry. The tank was designed using an in-house Monte-Carlo optical ray-tracing simulation, and was cast in polyurethane using a 3D printed mould. IDOS spatial accuracy was evaluated by imaging a set of custom optical phantoms, with comparison to x-ray CT images. IDOS dose measurement performance was assessed by imaging PRESAGE dosimeters irradiated with simple known dose distributions (e.g., 4 field box 6MV treatment with Varian Linac). Direct comparisons were made to images from our gold standard DLOS scanner and calculated dose distributions from a commissioned Eclipse planning system. Results: All optical CT images were reconstructed at 1mm isotropic resolution. Comparison of IDOS and x-ray CT images of the geometric phantom demonstrated excellent IDOS geometric accuracy (sub-mm) throughout the dosimeter. IDOS measured 3D dose distribution agreed well with prediction from Eclipse, with 95% gamma pass rate at 3%/3mm. Cross-scanner dose measurement gamma analysis shows >90% of pixels passing at 3%/3mm. Conclusion: The first prototype of the IDOS system has demonstrated promising performance, with accurate dosimeter readout and negligible spatial distortion. The use of optical simulations and 3D printing to create a light collimating-tank has dramatically increased convenience and reduced costs by removing the need for expensive lenses and large volumes of refractive matching fluids.

60 APPLIED LIFE SCIENCES↗

The characterization of microstructure and chemistry of transmutation fuels

The goal of the fast reactor development programs is fabrication and certification of a nuclear fuel system that performs all functions of a conventional fuel while destroying recycled actinides. Metal fuels, such as U-Pu-Zr fuels, are considered to be candidates for this application. The physical and mechanical properties, as well as behavior laws and correlations of metal alloy fuel, all of which define the behavior and performance of metal alloy fuels has been investigated in detail. The results indicated that the prospect for fueling a future fast spectrum reactor using metal fuels is excellent. There are several challenges associated with the fuel implementation in reactor environment. One of the limiting factors in lifetime and safety of thermal and fast reactor systems is fuel swelling and resulting fission product transport to cladding. Understanding diffusion kinetics and phases formed between metal fuel and cladding upon exposure to high temperatures typical in reactor environment is critical for ensuring integrity, safety, and performance of the material, advancement of this type of fuel in the future, and securing long-term success of the nuclear fleet. The first step to understanding fuel-cladding interaction is investigation of an as-cast fuel microstructure. Despite the importance of these fuels, detailed description of microstructures in these materials is extremely limited. The majority of published results are based on characterization of as-cast microstructures of these fuels in scanning electron microscopes (SEM). In this work, we present the results from microstructural characterization of metallic Pu-based fuels, which is essential in the validation of current and future atomistic and meso-scale modeling efforts. A firm understanding of microstructural evolution in reactor materials is imperative and will lead to deeper understanding of in-reactor degradation behavior, creating a new generation of radiation-resistant materials and fuels with the potential for significant increases in burn-up.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improved Gamma-Ray Point Source Quantification in Three Dimensions by Modeling Attenuation in the Scene

We discuss using a series of detector measurements taken at different locations to localize a source of radiation as a well-studied problem. The source of radiation is sometimes constrained to a single point-like source, in which case the location of the point source can be found using techniques such as maximum likelihood. Recent advancements have shown the ability to locate point sources in 2D and even 3D, but few have studied the effect of intervening material on the problem. In this work we examine gamma-ray data taken from a freely moving system and develop voxelized 3-D models of the scene using data from the onboard LiDAR. Ray casting is used to compute the distance each gamma ray travels through the scene material, which is then used to calculate attenuation assuming a single attenuation coefficient for solids within the geometry. Parameter estimation using maximum likelihood is performed to simultaneously find the attenuation coefficient, source activity, and source position that best match the data. Using a simulation, we validate the ability of this method to reconstruct the true location and activity of a source, along with the true attenuation coefficient of the structure it is inside, and then we apply the method to measured data with sources and find good agreement.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Scale-Up of Friction Self-piercing Riveting Process for Multi-material Joints

A single-class joining process known as “friction self-piercing riveting (F-SPR)” has been developed for joining various low-ductility lightweight materials on a laboratory scale. The frictional heat generated during the F-SPR process improved local ductility, resulting in crack-free joints and robust mechanical performance. This innovative joining technology was further advanced through the scale-up of the process using a new system with several key features (e.g., automatic rivet feeding and clamping system, vacuum system) toward industry readiness. The new integrated F-SPR systems were effectively demonstrated for joining different material combinations (e.g., carbon fiber composite to 7075 Al alloy, 7075 Al alloy to 7075 Al alloy, and 7075 Al alloy to casting Al Aural 5) with a unified technique. Crack-free joint with adequate mechanical interlocking resulted in good mechanical joint strength for each material combination. Then, the process was successfully scaled up by producing multiple joints without any cracks on larger CFC-Al and Al-Al components by the new integrated system, bringing it closer to industrial application.

Lim, Yong Chae [ORNL] (ORCID:0000000321773988)↗

High Speed Hybrid Reluctance Motor Utilizing Anisotropic Materials

With high cost and volatility driving continued efforts to decrease reliance on the critical heavy rare earth materials used in traction drive applications, General Motors developed three variants of heavy rare earth-free (HRE-free) electric motors. The variants focused on taking advantage of advanced magnet technologies and new rotor topologies to improve mechanical strength and achieve power targets. The three variants were a HRE-free permanent magnet reluctance motor, a synchronous reluctance motor utilizing small HRE-free permanent magnets, and an induction motor with inserted copper bars and cast aluminum end-rings. Motors were designed with the intent of primary or secondary traction applications, depending on the topology. Variant 1 achieved performance comparable to HRE-containing permanent magnet motors through optimized topology and validation of HRE-free magnets, focusing on achieving energy products and demagnetization resistance comparable to those of HRE-containing magnets. Demagnetization testing demonstrated the motor robustness to currents and temperatures exceeding expected vehicle conditions, a key challenge to the use of HRE-free magnets. The Variant 1 motor also showed the best capability of meeting the US Drive technology 2020 targets, due to the high power-density of the permanent magnet motor and the potential cost reductions enabled by the removal of heavy rare earth materials. Variant 2 exhibited high efficiency in high speed regions due to the low high-speed losses, an important consideration for secondary traction applications, and significantly thrifted on magnet mass to reduce cost. Variant 3 contained copper bars within the induction rotor to reduce losses compared to cast aluminum, while using cast aluminum end-rings to reduce the cost and mass of the rotor. Optimization of the Cu-Al interface were focused on, as the interface is prone to forming brittle intermetallic compounds during the casting process. Prototypes of each motor variant were built and tested for performance, mechanical strength, and demagnetization resistance (Variants 1 and 2 only), with torque and power resulting close to the predicted values.

33 ADVANCED PROPULSION SYSTEMS↗

Role of reinforcement learning for risk-based robust control of cyber-physical energy systems

Critical infrastructures such as cyber-physical energy systems (CPS-E) integrate information flow and physical operations that are vulnerable to natural and targeted failures. Safe, secure, and reliable operation and control of CPS-E is critical to ensure societal well-being and economic prosperity. Automated control is key for real-time operations and may be mathematically cast as a sequential decision-making problem under uncertainty. Emergence of data-driven techniques for decision making under uncertainty, such as reinforcement learning (RL), have led to promising advances for addressing sequential decision-making problems for risk-based robust CPS-E control. However, existing research challenges include understanding the applicability of RL methods across diverse CPS-E applications, addressing the effect of risk preferences across multiple RL methods, and development of open-source domain-aware simulation environments for RL experimentation within a CPS-E context. This article systematically analyzes the applicability of four types of RL methods (model-free, model-based, hybrid model-free and model-based, and hierarchical) for risk-based robust CPS-E control. Problem features and solution stability for the RL methods are also discussed. We demonstrate and compare the performance of multiple RL methods under different risk specifications (risk-averse, risk-neutral, and risk-seeking) through the development and application of an open-source simulation environment. Motivating numerical simulation examples include representative single-zone and multizone building control use cases. Finally, six key insights for future research and broader adoption of RL methods are identified, with specific emphasis on problem features, algorithmic explainability, and solution stability.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Digitalization of an experimental electrochemical reactor via the smart manufacturing innovation platform

The exponential increase in data produced over the last two decades has revolutionized the way we collect, store, process, analyze, model, and interpret information to improve profitability. Manufacturing is no exception. How- ever, Smart Manufacturing, the digital practice, organization, workforce, and infrastructure transformation for collection and deployment of data and models at scale and at all levels of manufacturing, is a complex, costly, and labor-intensive journey that is still seeing slow adoption. The Clean Energy Smart Manufacturing Innovation Institute (CESMII), a national Manufacturing USA public-private partnership sponsored by the Department of Energy, is addressing this scaled use of data and modeling in manufacturing. CESMII has focused on how to col- lect and use operating data for numerous applications that improve productivity, precision, and performance of manufacturing operations from factory floor to supply chain using process simulation, predictive analytics, mon- itoring and control, and real-time optimization. Because contextualized data are key, CESMII has developed the Smart Manufacturing Innovation Platform (SMIP) to lower the barriers to the data that are needed to accelerate data-based model building, improve data visualization, and more quickly gain insights. Reusable, standards-based ways of doing data collection, ingestion, and contextualization are particularly important for scaling access and use of data. The SMIP uses a standards-based definition and construct for reusable information models called an SM Profile. When an SM Profile is used in conjunction with the SMIP, the SMIP ensures the availability of contextualized, operational data for model building. The present work demonstrates Smart Manufacturing and the application of the SMIP for building several data-centered models for the operation and control of an ex- perimental electrochemical reactor that reduces carbon dioxide (CO 2 ) gas to valuable liquid and gas chemicals, such as alcohols, olefins, and syngas. We describe how the SMIP plays a central role in more effective model building and we demonstrate how the electochemical reactor can be controlled and optimized for the desired products. Use of the SMIP involves the transmission of real-time sensor measurements to a cloud resource so that the operating data are available to all model building experts. The data collection and transmission process is fully automated to greatly reduce the need for manual manipulation of the data. Data-driven machine learning models are used for advanced real-time state estimation, real-time optimization, and model-based feedback control for the reactor. The application models are implemented as a system to monitor the data flow and control the electrochemical reactor with a single visualization interface. SM Profiles are used to demonstrate reusability of the information models for the reactor and the instrumentation. The application packages, algorithms, and user interfaces developed are cast as Docker images in a library to facilitate reusability of the application models.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling Volatile Species Retention Experiments (Interim Progress Report) (M3FT-12LA0202053)

Metal nuclear fuel is a candidate transmutation fuel form for advanced fuel cycles. One constituent of the fuel, americium, has a high vapor pressure, and there is a concern that excessive volatility losses of americium will occur during casting of the metal. A number of experiments have been performed using americium and surrogate metals, including experiments slated for FY12, to address the concern. The present task is to model and numerically simulate these experiments. This report describes a system-level model of the relevant experiments that has been developed together with some results. It also describes some initial 3D, full-physics simulations of portions of the experiments that have been performed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗