SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The microstructural development of binary alloys during directional solidification is studied. Cellular growth data for the Al-Cu and Pb-Sn binary alloy systems are analyzed in order evaluate the criteria of Kurz and Fisher (1981) and Trivedi (1984) for cellular-dendritic transition. It is observed that the experimental growth values do not correlate with the Kurz and Fisher or Trivedi data.
The departure from interface planarity and the subsequent evolution to a periodic array of cells or dendrites is a fundamental process that characterizes most microstructures in solidified alloys. The growing demand for high quality alloys and semiconductor crystals requires a precise methodology to predict and subsequently control both the interface morphology and the distribution of impurities, additives, and phases in the grown crystal. Apart from its practical significance, the study of morphological evolution has also been viewed as a means to unearth a general paradigm for pattern formation in nature. A previously developed 2D numerical model for the solid/liquid interface tracking has been further refined and used to simulate the time-evolution of the perturbations on the interface. The dynamics of the local growth velocity, interface undercooling and solute concentration at the interface has been theoretically predicted by means of the numerical model for Al-Cu and Pb-Sn alloys. The model shows that perturbations with a wavelengths, lambda greater than a critical wavelength lambda(sub c) continue to grow in time whereas perturbations with lambda < lambda(sub c) cease to propagate. The model further predicts that under certain conditions perturbation can also propagate along the interface. Comparison of these predictions with existing theories of pattern formation and experimental results will be discussed.
When dispersed or mixed immiscibles are solidified on earth, a large amount of separation of the constituents takes place due to differences in densities. However, when the immiscibles are dispersed and solidified in zero-gravity, density separation does not occur, and unique composite solids can be formed with many new and promising electrical properties. By measuring the electrical resistivity and superconducting critical temperature of zero-g processed Ga-Bi samples, it has been found that the electrical properties of such materials are entirely different from the basic constituents and the ground control samples. The finest dispersions are obtained only in a low-gravity environment. Our results indicate that space-processed immiscible materials may form an entirely new class of electronic materials. The interesting electrical properties of directionally solidified Al-Cu eutectic, a two-component alloy consisting of Al and Al2Cu which was processed on Skylab (M566) are briefly reviewed. The electrical resistivity of directionally solidified eutectics with a lamellar structure are highly anisotropic and have been studied both experimentally and theoretically. The local resistivity of the space-processed samples are compared to a ground control sample and to the expected theoretical results.
Two classes of material processing scenarios will feature prominently in future interplanetary exploration: in situ production using locally available materials in lunar or planetary landings and high performance structural materials which carve out a set of properties for uniquely hostile space environments. To be competitive, high performance materials must typically offer orders of magnitude improvements in thermal conductivity or insulation, deliver high strength-to-weight ratios, or provide superior durability (low corrosion and/or ablative character, e.g., in heat shields). The space-related environmental parameters of high radiation flux, low weight, and superior reliability limits many typical aerospace materials to a short list comprising high performance alloys, nanocomposites and thin-layer metal laminates (Al-Cu, Al-Ag) with typical dimensions less than the Frank-Reed-type dislocation source. Extremely light weight carbon-carbon composites and carbon aerogels will be presented as novel examples which define broadened material parameters, particularly owing to their extreme thermal insulation (R-32-64) and low densities (<0.01 g/cu cm) approaching that of air itself. Even with these low-weight payload additions, rocket thrust limits and transport costs will always place a premium on assembling as much structural and life support resources upon interplanetary, lunar, or asteroid arrival. As an example, for in situ lunar glass manufacture, solar furnaces reaching 1700 C for pure silica glass manufacture in situ are compared with sol-gel technology and acid-leached ultrapure (<0.1% FeO) silica aerogel precursors.
Two classes of material processing scenarios will feature prominently in future interplanetary exploration- in situ production using locally available materials in lunar or planetary landings and high performance structural materials which carve out a set of properties for uniquely hostile space environments. To be competitive, high performance materials must typically offer orders of magnitude improvements in thermal conductivity or insulation, deliver high strength-to-weight ratios, or provide superior durability (low corrosion and/or ablative character, e.g. in heat shields). The space-related environmental parameters of high radiation flux, low weight and superior reliability limits many typical aerospace materials to a short list comprising high performance alloys, nanocomposites and thin-layer metal laminates (Al-Cu, Al-Ag) with typical dimensions less than the Frank-Reed-type dislocation source. Extremely light weight carbon-carbon composites and car on aerogels will be presented as novel examples which define broadened material parameters, particularly owing to their extreme thermal insulation (R-32-64) and low densities (less than 0.01 g/cc) approaching that of air itself. Even with these low weight payload additions, rocket thrust limits and transport costs will always place a premium on assembling as much structural and life support resources upon interplanetary, lunar or asteroid arrival. As an example for in situ lunar glass manufacture, solar furnaces reaching 1700 C for pure silica glass manufacture in situ are compared with sol-gel technology and acid-leached ultrapure (less than 0.1% FeO) silica aerogel precursors.
An investigation has been carried out to examine the relationship of the observed chemical and mechanical properties of Al-Cu and Al-Zn-Mg alloys to the stress corrosion mechanisms which dominate in each case. Two high purity alloys and analogous commercial alloys were selected. Fundamental differences between the behavior of Al-Cu and of Al-Zn-Mg alloys were observed. These differences in the corrosion behavior of the two types of alloys are augmented by substantial differences in their mechanical behavior. The relative cleavage energy of the grain boundaries is of particular importance.
We introduce a new phase-field formulation of rapid alloy solidification that quantitatively in- corporates non-equilibrium effects at the solid-liquid interface over a very wide range of interface velocities. Simulations identify a new dynamical instability of dendrite tip growth driven by solute trapping at velocities approaching the absolute stability limit. They also reproduce the formation of the widely observed banded microstructures, revealing how this instability triggers transitions between dendritic and microsegregation-free solidification. Predicted band spacings agree quantita- tively with observations in rapidly solidified Al-Cu thin films.
Tomography (CT) has proved to be of inestimable use in providing a rapid evaluation of a variety of samples from Mechanics of Granular Materials (MGM) to electronic materials (Ge-Si alloys) to space grown materials such as meteorites. The system at Kennedy Space Center (KSC), because of its convenient geographical location, is ideal for examining samples before launch and immediately after returning to Earth. It also has the advantage of the choice of fluxes, and in particular the use of a radioactive cobalt source, which is basically monochromatic. This permits a reasonable measurement of density to be made from which chemical composition can be determined. Due to the current dearth of long duration space grown materials, the CT instrument has been used: (1) to characterize materials in preparation for flight, (2) to determine thermal expansion values, and (3) to examine long duration space grown materials, i.e. meteorites. This work will first describe the establishment of the protocol for obtaining the optimum density readings for any material. Included will be the effects of the hardware or instrumental parameters that can be controlled, and the techniques used to process the CT data. Examples will be given of the compositional variation along a single crystal of Ge-Si alloy. Density variation with temperature has been measured in preparation for future materials science experiments; this involved the fabrication at MSFC and installation of a single zone furnace at KSC incorporating a heat pipe to ensure high temperature uniformity. At the time of writing the thermal expansion of lead (Pb) has been measured from room temperature to 900 C. Three methods are available. Digital radiography enables length changes to be determined. Prior to melting the sample is smaller than the container and the diameter change can be measured. Most critical, however, is the density change in solid, through the melting region, and in the liquid state. These data are needed for engineering purposes to aid in the design of containment cartridges, and for enabling fluid flow calculations. A second sample, with the Pb alloyed with Sb is ready for scanning. This corresponds to the planned composition of Dr. Poirier s flight experiment. Other materials pertinent to NASA programs such as Al-Cu (Trivedi), CdTe (Banish), HgCdTe (Lehoczky) will be examined below and above the melting point. Finally, three-dimensional results will be shown of the structure of a two-phase metallic meteorite of metal and sulfide, in which the Fe-Ni phase has coarsened during slow cooling over hundreds of millions of years.
The integrally stiffened cylinder (ISC) process, pioneered by NASA Langley Research Center, offers significant savings for launch vehicle structures. The ISC process is a near net shape, advanced manufacturing method for fabrication of single-piece, thin-walled barrels with internal longitudinal stiffeners, eliminating the need for longitudinal welding and machining. A cost-benefit analysis of the ISC process estimated a 50 % reduction in manufacturing costs and a 10% weight savings over the current multi-piece, machined and welded construction approach for stiffened barrels. In 2017, commercial-scale manufacturing trials were pursued, leading to a successful manufacturing demonstration of 10-ft. diameter ISC barrels fabricated from Al alloy 2219. Some cracking was observed in the stiffeners during fabrication. Optical metallography was performed to evaluate the as-formed microstructures to identify potential causes of cracking, along with mechanical testing to evaluate formability. Results revealed that cracking in the stiffeners was attributed to three likely causes: 1) large Al-Cu stringer particles, 2) stick-slip friction between the mandrel and ISC due to non-optimized lubrication, and 3) differences in material flow rate between the wall and stiffener locations. Testing to gauge formability revealed a significant decrease in ductility in the longitudinal directional for the as-formed condition, attributed to reduced ductility due to the large Al-Cu stringer particles. These results provide guidance toward materials and processing modifications for future ISC forming trials.
In this work, the thermodynamic properties of α-Al and other phases (GP zones, θ'', θ' and θ) in the Al-rich part of the Al-Cu system have been obtained by means of the cluster expansion formalism in combination with statistical mechanics. This information was used to build the Al-rich part of the Al-Cu phase-diagram taking into account vibrational entropic contributions for θ', as those of the other phases were negligible. The simulation predictions of the phase boundaries between α-Al and either θ'', θ' or θ phases as a function of temperature are in good agreement with experimental data and extend the phase boundaries to a wider temperature range. The DFT calculations reveal the presence of a number of metastable Guinier-Preston-zone type configurations that may coexist with α-Al and θ'' at low temperatures. They also demonstrate that θ' is the stable phase below 550K but it is replaced by θ above this temperature due to the vibrational entropic contribution to the Gibbs energy of θ'. This work shows how the combination of cluster expansion and statistical mechanics can be used to expand our knowledge of the phase diagram of metallic alloys and to provide Gibbs free energies of different phases that can be used as input in mesoscale simulations of precipitation.
The European Space Agency (ESA) - Microgravity Application Promotion (MAP) programme entitled XRMON (In situ X-Ray MONitoring of advanced metallurgical processes under microgravity and terrestrial conditions) aims to develop and perform in situ X-ray radiography observations of metallurgical processes in microgravity and terrestrial environments. The use of X-ray imaging methods makes it possible to study alloy solidification processes with spatio-temporal resolutions at the scales of relevance for microstructure formation. XRMON has been selected for MASER 12 sounding rocket experiment, scheduled in autumn 2011. Although the microgravity duration is typically six minutes, this short time is sufficient to investigate a solidification experiment with X-ray radiography. This communication will report on the preliminary results obtained with the experimental set-up developed by SSC (Swedish Space Corporation). Presented results dealing with directional solidification of Al-Cu confirm the great interest of performing in situ characterization to analyse dynamical phenomena during solidification processes.
Currently, there are two national challenge problems that guide much of the research in durability and damage tolerance at NASA Langley. The first, Airframe Digital Twin, is a concept that combines as-built vehicle components, as-experienced loads and environments, and other vehicle-specific characteristics to enable ultrahigh fidelity modeling of aircraft and spacecraft throughout their service lives. The second, Materials Genome Initiative, is an analog to the Human Genome Project, and is intended to improve the rate at which materials scientists can discover, understand fundamental physics, and improve material systems. This presentation will highlight several research projects ongoing at NASA Langley that are in support of the above challenge problems. Two of those topics will be the subject of detailed discussion. First, investigations of microstructurally-small fatigue cracking (MSFC) in Al-2Cu and Al-4Cu, fabricated in-house, will be presented. Single- and oligo-crystals of Al-Cu specimens were loaded in uniaxial fatigue, while high-resolution in-situ measurements of deformation were made using image correlation (IC) in a scanning-electron microscope (SEM). The Al-Cu specimens were then replicated as crystal plasticity finite element models (CPFEM), where evolution of slip localization near grain boundaries was computed. Comparison among experiment and CPFEM is made. In addition, XRay diffraction measurements of the as-fabricated specimens were carried out, where direct measurements of the embedded copper precipitates were made, and their influence on growing MSFCs were directly observed. The second main topic will illustrate ongoing work in the area of so-called damage-sensing particles. In this work, shape-memory alloys are embedded in an aluminum alloy matrix. Upon the propagation of a fatigue crack, these particles undergo a strain-induced phase transformation which is detected using an acoustic sensor, providing real-time information on propagating cracks. Experiments and simulations regarding the development of this system will also be detailed.
The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurcation is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher gradients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.
The dependence of primary arm spacings on growth speed was investigated for cellular and dendritic arrays in Pb-10 wt percent Sn samples directionally solidified under a constant positive thermal gradient in the melt. The gradient of constitutional supercooling was varied from almost zero (near the break-down of the planar liquid-solid interface at small growth speeds, cellular morphology) to near unity (large growth speeds, dendritic morphology). The spatial arrangements of cells and dendrites, as given by their coordination number, are not very different from each other. It appears that primary arm spacing maxima and the cell to dendrite transition are strongly influenced by the magnitude of the solute partition coefficient. The planar to cellular bifurction is supercritical in Pb-Sn which has a high partition coefficient, as compared to the subcritical behavior reported in Al-Cu and succinonitrile-acetone, both of which have low partition coefficients. The primary arm spacing model due to Hunt agrees with the experimentally observed trend for the whole growth regime. There is a good quantitative agreement at higher grdients of supercooling. However, the model overpredicts the primary arm spacings at low gradients of constitutional supercooling.
The effect of alloying elements on hydrogen solubility were determined by evaluating solubility equations and interaction coefficients. The solubility of dry hydrogen at one atmosphere was investigated in liquid aluminum, Al-Ti, Al-Si, Al-Fe, liquid gold, Au-Cu, and Au-Pd. The design of rapid heating and high pressure casting furnaces used in meta foam experiments is discussed as well as the mechanism of precipitation of pores in melts, and the effect of hydrogen on the shrinkage porosity of Al-Cu and Al-Si alloys. Hydrogen embrittlement in iron base alloys is also examined.
Recent improvements in the resolution of the X-ray Transmission Microscope (XTM) for Solidification Studies provide microstructure feature detectability down to 5 micrometers during solidification. This presentation will show the recent results from observations made in real-time of the solid-liquid interfacial morphologies of the Al-CuAI2 eutectic alloy. Lamellar dimensions and spacings, transitions of morphology caused by growth rate changes, and eutectic grain structures are open to measurements. A unique vantage point viewing the face of the interface isotherm is possible for the first time with the XTM due to its infinite depth of field. A video of the solid-liquid interfaces seen in-situ and in real-time will be shown.
In 2012, a pathfinder forward pressure vessel bulkhead (FPVBH) for the Orion Multi-Purpose Crew Vehicle (MPCV) was fabricated using aluminum (Al) alloy 2219. The demonstration article was offered as a replacement for the baseline configuration, which at that time was a multi-piece welded construction using aluminum-lithium (Al-Li) alloy 2195. In 2014, the NASA Engineering and Safety Center (NESC) funded a Phase I effort to explore spin-forming as a manufacturing method to produce a complex-shaped, single-piece FPVBH for the crew module (CM) [1]. The primary focus of the NESC effort was to expand spin-forming technology to the fabrication of an Al-Li 2195 FPVBH. As a result, limited testing and analysis was performed on the original Al 2219 article. In this study, a sufficiently large plate of Al 2219 was not available for the fabrication of a FPVBH. Therefore, the forming blank comprised two plates (from different lots) butt welded together using a single friction stir weld. The welded forming blank was then spin formed into the FPVBH configuration and heat treated to the T62 temper. Mechanical property testing of the spin-formed 2219-T62 FPVBH revealed that the tensile properties were comparable to the Metallic Material Properties Development and Standardization (MMPDS) A-basis allowable for Al 2219-T6 wrought products. However, post-spin forming application of the standard heat treatment produced large, recrystallized grains in the material. The response varied within the two plates; one plate lot exhibited nearly complete recrystallization, while the other lot contained bands of recrystallization. Although no reduction in tensile properties was observed due to these microstructural variations, a more detailed investigation was recommended to better understand the effect of spin forming on the recrystallization mechanism and the impact on other material properties. The current study examined the microstructure and mechanical properties of the fully processed Al 2219-T62 FPVBH with emphasis on comparing differences between the two plates. Testing was limited to the cone region of the FPVBH. The two specific tasks in this study were: a) Characterization of the microstructure and mechanical properties in the two plates used in the FPVBH. b) Isolation of the impact of each step in the thermo-mechanical processing (TMP) sequence of the FPVBH on recrystallization and grain growth. Mechanical property testing sampled regions containing both large, recrystallized and small, unrecrystallized grains. Tensile strengths and elongations were equivalent in both regions and exceeded MMPDS A-basis allowables. Fracture toughness was equivalent in both regions and fracture morphology was typical of aluminum alloys. The fatigue precrack region of the fracture toughness specimens appeared more faceted in the recrystallized plate. This suggests that property testing that is more sensitive to grain size, such as fatigue crack growth rate and stress corrosion cracking, may be warranted. Alcoa reviewed the production records for the two plate lots and confirmed that composition of both plates was within the allowable range for Al 2219 and that plate processing steps were all performed within production limits. However, the Fe content was notably higher in the fully recrystallized plate, resulting in a greater volume fraction of large Fe-bearing inclusions and Al-Cu constituent particles. Alcoa did not provide details regarding plate processing variables for the two plate lots. It was surmised that deformation by hot rolling was the most accurate TMP simulation of commercial spin forming within a laboratory setting. Both hot rolling and spin forming comprise combinations of shear and compressive deformation. The through-thickness strain caused by hot rolling is symmetrical about the mid-plane, as the rollers contact both sides of the material. Shear strains are maximum at the inner and outer surfaces and trend toward zero at the mid-thickness. In contrast, spin forming utilizes a single roller on the outer surface, producing a gradient in shear stress through the thickness. Shear strains in spin-formed material are highest at the outer surface due to direct contact with the roller, and trend toward zero at the inner surface. Consequently, there will undoubtedly be some discrepancies in the mechanical response of hot-rolled and spin-formed products in the through-thickness direction. Interrupted TMP simulations were performed on remnant plate from the FPVBH forming blank in order to isolate the effects of a post-weld anneal, spin-forming deformation/thermal cycling, and solution heat treatment (SHT) on development of the recrystallized microstructures. Analysis confirmed that large, recrystallized grains formed exclusively during SHT and only after a certain deformation level was exceeded. Remnant plate from both lots that received thermal processing only did not exhibit recrystallization but exhibited fully recrystallized microstructures when processed by hot rolling. This indicates that (1) the level of deformation exceeded the critical level for recrystallization in both plates and (2) that the level of deformation during hot rolling was greater than that which accumulated during spin forming of the FPVBH. Comparison of the hot-rolled plate with the spin-formed material showed that the recrystallized grain size was larger in the FPVBH, providing further evidence that deformation levels were lower in the FPVBH. The most plausible explanation for the differing degrees of recrystallization in the two plates is particle stimulated nucleation (PSN) at the Fe-bearing inclusions and large Al-Cu constituent particles. In the plate with higher solute content, the greater volume fraction of these particles reduces the deformation level required to promote recrystallization. During spin forming the critical deformation level was likely exceeded for the higher Fe content plate resulting in a fully recrystallized microstructure. The lower Fe content plate developed a microstructure that exhibited bands of recrystallization due to the combination of a non-uniform distribution of particles and deformation. The critical deformation required for recrystallization was likely only exceeded during spin forming in regions of higher particle content. While there were differences in Fe content between these lots of Al 2219 plate, the composition of both was within defined alloy limits and Alcoa reported no anomalies during plate production. The observed differences in recrystallization after spin forming may reflect the inherent variability between these two lots of plate. The spin-forming vendor, Spincraft, reported that similar variations in recrystallized microstructures have been observed during examination of multiple spin-forming trials of a different 2xxx series aluminum alloy. Hence, tighter chemical specification limits on impurity levels in Al 2219 plate may help ensure uniform, predictable microstructures. Finally, the tensile and fracture toughness properties were not affected by the microstructural variations noted.