Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alloy anodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Overcoming Anode Instability in Solid‐State Batteries through Control of the Lithium Metal Microstructure

Abstract Enabling the lithium metal anode (LMA) in solid‐state batteries (SSBs) is the key to developing high energy density battery technologies. However, maintaining a stable electrode–electrolyte interface presents a critical challenge to high cycling rate and prolonged cycle life. One such issue is the interfacial pore formation in LMA during stripping. To overcome this, either higher stack pressure or binary lithium alloy anodes are used. Herein, it is shown that fine‐grained ( d = 20 µm) polycrystalline LMA can avoid pore formation by exploiting the microstructural dependence of the creep rates. In a symmetric cell set‐up, i.e., LiǀLi 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO)ǀLi, fine‐grained LMA achieves > 11.0 mAh cm −2 compared to ≈ 3.6 mAh cm −2 for coarse‐grained LMA ( d = 295 µm) at 0.1 mA cm −2 and at moderate stress of 2.0 MPa. Smaller diffusion lengths (≈ 20 µm) and higher diffusivity pathway along dislocations ( D d ≈ 10 −7 cm 2 s −1 ), generated during cell fabrication, result in enhanced viscoplastic deformation in fine‐grained polycrystalline LMA. The electrochemical performances corroborate well with estimated creep rates. Thus, microstructural control of LMA can significantly reduce the required stack pressure during stripping. These results are particularly relevant for “anode‐free” SSBs wherein both the microstructure and the mechanical state of the lithium are critical parameters.

25 ENERGY STORAGE↗
NASA NTRS2007

Lithium Dinitramide as an Additive in Lithium Power Cells

Lithium dinitramide, LiN(NO2)2 has shown promise as an additive to nonaqueous electrolytes in rechargeable and non-rechargeable lithium-ion-based electrochemical power cells. Such non-aqueous electrolytes consist of lithium salts dissolved in mixtures of organic ethers, esters, carbonates, or acetals. The benefits of adding lithium dinitramide (which is also a lithium salt) include lower irreversible loss of capacity on the first charge/discharge cycle, higher cycle life, lower self-discharge, greater flexibility in selection of electrolyte solvents, and greater charge capacity. The need for a suitable electrolyte additive arises as follows: The metallic lithium in the anode of a lithium-ion-based power cell is so highly reactive that in addition to the desired main electrochemical reaction, it engages in side reactions that cause formation of resistive films and dendrites, which degrade performance as quantified in terms of charge capacity, cycle life, shelf life, first-cycle irreversible capacity loss, specific power, and specific energy. The incidence of side reactions can be reduced through the formation of a solid-electrolyte interface (SEI) a thin film that prevents direct contact between the lithium anode material and the electrolyte. Ideally, an SEI should chemically protect the anode and the electrolyte from each other while exhibiting high conductivity for lithium ions and little or no conductivity for electrons. A suitable additive can act as an SEI promoter. Heretofore, most SEI promotion was thought to derive from organic molecules in electrolyte solutions. In contrast, lithium dinitramide is inorganic. Dinitramide compounds are known as oxidizers in rocket-fuel chemistry and until now, were not known as SEI promoters in battery chemistry. Although the exact reason for the improvement afforded by the addition of lithium dinitramide is not clear, it has been hypothesized that lithium dinitramide competes with other electrolyte constituents to react with lithium on the surface of the anode to form a beneficial SEI. Apparently, nitrides and oxides that result from reduction of lithium dinitramide on the anode produce a thin, robust SEI different from the SEIs formed from organic SEI promoters. The SEI formed from lithium dinitramide is more electronically insulating than is the film formed in the presence of an otherwise identical electrolyte that does not include lithium dinitramide. SEI promotion with lithium dinitramide is useful in batteries with metallic lithium and lithium alloy anodes.

Gorkovenko, Alexander A.↗
DOE OSTI2022

Nanoscale Three-Dimensional Imaging of Degradation in Composite Si-Containing Anodes

The use of silicon (Si) in next-generation lithium-ion battery (LIB) anodes has the potential to dramatically improve electrochemical performance over current LIB graphite (Gr) anodes, due to silicon’s higher specific capacity.1 However, widespread implementation of Si-containing anodes is inhibited by issues such as significant Si volume expansion during lithiation and an unstable solid-electrolyte interphase (SEI), resulting in unreliable performance and poor cycle life. Currently, composite anodes with both Si and graphite active materials are used to increase capacity and mitigate some of the limitations associated with Si. In composite electrodes with a heterogeneous distribution of components with varying electrical properties (including Si, Gr, conductive carbon additive, and binder), it is important to understand the local distribution of each component to correlate with electrochemical processes, particularly localized degradation and heterogeneous aging, and to optimize performance. To investigate Si-containing composite anodes in the nanoscale, we use scanning spreading resistance microscopy (SSRM), a form of scanning probe microscopy (SPM) that probes local electronic resistivity. By examining the intrinsic electronic resistivity contrast between the anode components, separate phases can be distinguished and understood within the composite structure.2 This work studies the effect of electrochemical cycling in two different electrolytes on component distribution and aging by comparing the electrical and structural evolution of composite Si-graphite electrodes and SEI before and after charge-discharge cycling. 1. W. J. Zhang. A review of the electrochemical performance of alloy anodes for lithium-ion batteries J. Power Sources 196 13–24 (2011). 2. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. Finegan, S.-D. Han and S. DeCaluwe: Three-Dimensional Mapping of Resistivity and Microstructure of Composite Electrodes for Lithium-Ion Batteries. ACS Nano Letters Accepted (2020).

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Evolution of solid electrolyte interphase and active material in the silicon wafer model system

Alloying anode materials for lithium-ion batteries, such as silicon (Si), are an important focus of materials research due to the demand for increased energy density for electric vehicles and stationary grid storage. However, progress towards next generation anode materials has been hindered by poor capacity retention due to the instability of the Si active material and the solid electrolyte interphase (SEI). Herein, the evolution of the active Si material and the SEI are simultaneously investigated from the perspective of chemical, structural, morphological, and electronic evolution in the Si wafer model system through its cycling life, using time-of-flight secondary ion mass spectrometry (TOF-SIMS), scanning transmission electron microscopy (STEM), atomic force microscopy (AFM), and scanning spreading resistance microscopy (SSRM). The results illustrate a dynamic evolution of the SEI and active Si material through cycling. Through an improved understanding of evolution of SEI and Si active material within the Si wafer model system, mitigation strategies may be designed to extend the lifetime of Si anodes.

25 ENERGY STORAGE↗
DOE OSTI2020

Microscopic Observation of Solid Electrolyte Interphase Bilayer Inversion on Silicon Oxide

Silicon has been investigated in recent years as an alloying anode material to enhance gravimetric energy density in lithium-ion batteries. Although recent developments have suggested that silicon oxides exhibit improved cycling stability over pure Si, the origin of the improved cycling performance is still poorly understood. The initial solid electrolyte interphase (SEI) formation mechanisms on Si wafers with both native oxide and chemically etched thermal oxide coatings are investigated structurally, chemically, and morphologically in the nanoscale. After one electrochemical cycle, microscopy reveals that SEI formed on native SiO x features the typical SEI bilayer structure with a carbon-rich outer SEI layer and an inorganic-rich inner SEI layer. In contrast, the SEI formed on chemically etched thermal oxide shows an inversion in the structure. This work observes distinct initial SEI formation mechanisms on the HF-etched SiO 2 surface, which may be partially responsible for improved cycle life observed in SiO x -based anode materials.

25 ENERGY STORAGE↗
DOE OSTI2025

Mechanically Robust Bismuth-Embedded Carbon Microspheres for Ultrafast Charging and Ultrastable Sodium-Ion Batteries

Advancements in the development of fast-charging and long-lasting microstructured alloying anodes with high volumetric capacities are essential for enhancing the operational efficiency of sodium-ion batteries (SIBs). These anodes, however, face challenges such as declined cyclability and rate capability, primarily due to mechanical degradation reduced by significant volumetric changes (over 252%) and slow kinetics of sodium-ion storage. Herein, we introduce a novel anode design featuring densely packed bismuth (Bi) embedded within highly conductive carbon microspheres to overcome the aforementioned challenges. Remarkably, the high loading Bi anode within carbon microspheres with a high tap density of 2.59 g cm -3 possesses significant mechanical strength exceeding 590 MPa and limits volume swelling of only 10.9% post-sodiation. This anode demonstrates a high volumetric capacity (908.3 mAh cm -3 ), ultrafast chargeability (200 A g -1 , full charge/discharge in just 5.5 s), and outstanding cyclability over 12,000 cycles and maintains exceptional cycling stability even at -30 °C. The full cell paired with a Na 3 V 2 (PO 4 ) 3 cathode retains over 80% capacity after 600 cycles at 36 C, demonstrating a remarkable rate capability of 126 C (full charge/discharge in 28.6 s). Our comprehensive experimental evaluations and chemo-mechanical simulations shed light on the mechanisms underpinning the anode's superior performance. In conclusion, this development marks a significant advancement in the design of durable and fast-charging anodes for high-performance SIBs.

25 ENERGY STORAGE↗
DOE OSTI2024

Low-cost iron trichloride cathode for all-solid-state lithium-ion batteries

The dominant chemistries of lithium-ion batteries on the market today still rely on flammable organic liquid electrolytes and cathodes containing scarce metals, such as cobalt or nickel, raising safety, cost and environmental concerns. Here we show a FeCl 3 cathode that costs as little as 1% of the cost of a LiCoO 2 cathode or 2% of a LiFePO 4 cathode. Once coupled with a solid halide electrolyte and a lithium-indium (Li–In) alloy anode, it enables all-solid-state lithium-ion batteries without any liquid components. Notably, FeCl 3 exhibits two flat voltage plateaux between 3.5 and 3.8 V versus Li + /Li, and the solid cell retains 83% of its initial capacity after 1,000 cycles with an average Coulombic efficiency of 99.95%. Combined neutron diffraction and X-ray absorption spectroscopy characterizations reveal a Li-ion (de)intercalation mechanism together with a Fe 2+ /Fe 3+ redox process. Further, our work provides a promising avenue for developing sustainable battery technologies with a favourable balance of performance, cost and safety.

25 ENERGY STORAGE↗
DOE OSTI2022

Effect of electrochemical cycling on microstructures of nanocomposite silicon electrodes using hyperpolarized 129 Xe and 7 Li NMR spectroscopy

The microstructural stability of composite electrodes during electrochemical cycling is critically important as it dictates the performance of Li-ion batteries. The issue becomes even more important for the high capacity alloying anode such as silicon that typically exhibits dramatic lithiation–delithiation-induced volume changes. The solid electrolyte interphase (SEI) layer formed on the active electrode surface has a profound effect on the overall microstructural stability of composite electrodes. An ideal SEI layer allows Li+ ions in and out of the electrode, but is an insulator to electrons, preventing the electrolyte from being further reduced. However, the SEI layers formed during initial lithiation may experience changes or degradation with subsequent cycling, adversely affecting the electrode performance. A combination of hyperpolarized 129 Xe and 7 Li nuclear magnetic resonance spectroscopies was applied to probe the microstructures of nanocomposite silicon electrodes at various stages of the lithiation–delithiation cycle. The results obtained from this study shed light on the degradation mechanism of nanocomposite Si electrodes upon electrochemical cycling and should prove useful in the effort to design more robust electrodes in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Benchmarking Solid-State Batteries Containing Sulfide Separators: Effects of Electrode Composition and Stack Pressure

Integrating sulfide separators into solid-state batteries (SSBs) containing high energy cathodes typically requires one or more materials and engineering solutions including: (i) applying interfacial coatings to mitigate electrolyte decomposition, (ii) applying high stack pressures to form robust solid-solid contacts, and (iii) using alloying anodes to avoid Li dendrite formation. Despite the promise of these approaches, a lack of standardized testing protocols makes it difficult to directly compare results among different studies. To address this problem, the present work benchmarks the performance of SSBs containing β-Li 3 PS 4 (LPS) separators and composite cathodes. By systematically varying the anode/cathode composition and stack pressure, this work demonstrates that cathode design is a major bottleneck for solid-state cells cycled at low rates (<100 µA cm -2 ). Operando stack pressure measurements show that, while mechanical confinement generally promotes higher active material utilization and cycling stability, this strategy alone does not address interfacial reactivity between LPS and high voltage cathodes. Here, these results also demonstrate that stress evolution during cycling is dominated by volume changes at the Li metal anode. Finally, we show that FeS 2 cathodes with moderate operating voltages (<3 V vs Li/Li + ) exhibit superior cycling performance compared to high voltage cathodes by facilitating formation of stable cathode/electrolyte interfaces.

25 ENERGY STORAGE↗
DOE OSTI2022

Batteries (2021 Annual Progress Report)

This document summarizes the progress of VTO battery R&D projects supported during the fiscal year 2021 (FY 2021). In FY 2021, the DOE VTO battery R&D funding was approximately $\$$115 million. Its R&D focus was on the development of high-energy batteries for EVs as well as very high-power devices for hybrid vehicles. The electrochemical energy storage roadmap (which can be found at the EERE Roadmap web page2) describes ongoing and planned efforts to develop electrochemical storage technologies for EVs. To advance battery technology, which can in turn improve market penetration of PEVs, the program investigates various battery chemistries to overcome specific technical barriers, e.g., battery cost, performance, life (both the calendar life and the cycle life), its tolerance to abusive conditions, and its recyclability/sustainability. VTO R&D has had considerable success, lowering the cost of EV battery packs to $\$$185/kWh in 2019 (representing more than 80% reduction since 2008) yet even further cost reduction is necessary for EVs to achieve head-to-head cost competitiveness with ICEs (without Federal subsidies). In addition, today’s batteries also need improvements in such areas as their ability to accept charging at a high rate, referred to as extreme fast charging (XFC) (15 minute charge) – to provide a “refueling” convenience similar to ICEs, and the ability to operate adequately at low temperatures. Research into “next-gen lithium-ion” batteries which would provide such functionalities is one of the R&D focus areas. VTO is funding research on both “next gen” chemistries (which employ an alloy anode and/or a high voltage cathode) and beyond lithium-ion (BLI) chemistries (which can, for example, employ a lithium metal anode).

25 ENERGY STORAGE↗
NASA NTRS2008

Advanced Lithium-Ion Cell Development for NASA's Constellation Missions

The Energy Storage Project of NASA s Exploration Technology Development Program is developing advanced lithium-ion batteries to meet the requirements for specific Constellation missions. NASA GRC, in conjunction with JPL and JSC, is leading efforts to develop High Energy and Ultra High Energy cells for three primary Constellation customers: Altair, Extravehicular Activities (EVA), and Lunar Surface Systems. The objective of the High Energy cell development is to enable a battery system that can operationally deliver approximately 150 Wh/kg for 2000 cycles. The Ultra High Energy cell development will enable a battery system that can operationally deliver 220 Wh/kg for 200 cycles. To accomplish these goals, cathode, electrolyte, separator, and safety components are being developed for High Energy Cells. The Ultra High Energy cell development adds lithium alloy anodes to the component development portfolio to enable much higher cell-level specific energy. The Ultra High Energy cell development is targeted for the ascent stage of Altair, which is the Lunar Lander, and for power for the Portable Life support System of the EVA Lunar spacesuit. For these missions, mass is highly critical, but only a limited number of cycles are required. The High Energy cell development is primarily targeted for Mobility Systems (rovers) for Lunar Surface Systems, however, due to the high risk nature of the Ultra High Energy cell development, the High Energy cell will also serve as a backup technology for Altair and EVA. This paper will discuss mission requirements and the goals of the material, component, and cell development efforts in further detail.

Reid, Concha M.↗
NASA NTRS2023

Long Life Molten Salt Battery for NASA Venus Application

A development program is being conducted at Advanced Thermal Batteries (ATB) to create a low discharge rate, long life, molten salt battery for a NASA Venus surface probe. Battery goals are 60 days continuous operation at +25V +0/-6 volts and -25V +6/-0 Volts under severe environments of 465°C, 92 atm pressure, and corrosive sulfur dioxide in a super critical carbon dioxide atmosphere. Conveniently, molten salt thermal battery electrochemistry starts to operate efficiently at 330°C. However, a major barrier to direct application of existing thermal battery technology is the high self-discharge rate, resulting in lifetimes in only minutes, not days. The best performance to date, which meets the required voltage regulation, has been a lithium silicon (LiSi) alloy anode discharging through all three voltage plateau versus an iron monosulfide (FeS) cathode. In order to perform reproducibly, additional engineering controls within the battery design are required to limit cell–to–cell parasitic discharge mechanisms. Results of these trials have improved the efficiency and manufacturability of the design.

Thermal Battery↗
DOE OSTI2025

Alloying Interlayers for Anode‐Less Lithium‐Metal Polymer Batteries

Anode‐less lithium‐metal batteries potentially offer further increased energy densities. However, the Coulombic efficiency (CE) of lithium plating and stripping, as a classical measure of Li inventory reversibility, is commonly still insufficient for achieving long‐lasting rechargeable batteries. Herein, the potential benefits of employing thin (20 nm) metal interlayers of Ag, Pt, and Au on Cu to alloy with Li in Cu||Li half‐cells and induce homogeneous Li plating with poly(ethylene oxide)‐based electrolytes are investigated. Interestingly, not all alloying interlayers enable a higher CE compared to neat Cu foil with 84%—specifically Ag@Cu with only 81%, while the best performing one, Au@Cu, provides a substantially increased CE of 91%. While generally the formation of “dead lithium” is found to be the major source of CE, this appears to be less pronounced in the case of Au@Cu, indeed. Further improvement can be achieved by carefully adjusting the cell voltage to a region in which the continuous de‐/alloying is suppressed, yielding a further enhanced CE of 94%, thus highlighting the need for a comprehensive approach to design suitable electrode chemistries and designs beyond a “simple” material improvement.

anode-less battery↗
DOE OSTI2025

Stable Cycling of Sodium All‐Solid‐State Batteries with High‐Capacity Cathode Presodiation

Sodium all-solid-state batteries (NaSSBs) with an alloy-type anode (e.g., Sn and Sb) offer superior capacity and energy density compared to hard carbon anode. However, the irreversible loss of Na + at the alloy anode during the initial cycle results in diminished capacity and stability, impairing full-cell performance. Here, this study presents an easy-to-implement cathode presodiation strategy by employing a Na-rich material to address these challenges. Leveraging the high theoretical capacity and suitable voltage window, Na 2 S is chosen as the Na donor, which is activated by creating a mixed electron-ion conducting network, delivering a high capacity of 511.7 mAh g −1 . By adding a small amount (i.e., 3 wt.%) of Na 2 S to the cathode composite, a NaCrO 2 || Sn full cell demonstrated capacity improvement from 90.8 to 118.2 mAh g −1 (based on cathode mass). The capacity-balanced full cell can thus cycle to more than 300 times with >90% capacity retention. This work provides a practical solution to enhance the full-cell performance and advance the transformation from half-cell to full-cell applications of NaSSBs.

25 - ENERGY STORAGE↗
DOE OSTI2021

Stress-Dependent Chemo-Mechanical Performance of Amorphous Si Anodes for Li-Ion Batteries upon Lithiation

Alloying-type anodes are significantly governed by their chemo-mechanical performance during the electrochemical cycling. The reaction-induced huge volumetric change of these anodes may cause material degradation and failure under mechanical constraints. Here, we investigate the stress-dependent lithiation behavior of amorphous Si (a-Si) anodes using molecular dynamics simulations. It is indicated that a-Si anodes can sustain higher hydrostatic stress than biaxial/uniaxial ones without the occurrence of mechanical failure. Thermodynamic and electrochemical calculations demonstrate that although the lithiation procedure also affects the thermodynamic stability of a-Si anodes, it is mainly dominated by the external mean stresses. Compressive stress is confirmed to destabilize a-Si anodes and further trigger their capacity fading. Compared with our atomistic simulations, previous continuum models underestimate the open-cell potentials of a-Si anodes, due to their ignored large volumetric deformation at higher stresses and Li concentrations. Finally, this computational study provides the intensive atomic-level understanding of the stress-dependent lithiation behavior of a-Si anodes.

25 ENERGY STORAGE↗