Search NASA⌕ Search

SEARCH · Search NASA

Results for “Alloy powder”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Powdered aluminum and oxygen rocket propellants: Subscale combustion experiments

Aluminum combined with oxygen has been proposed as a potential lunar in situ propellant for ascent/descent and return missions for future lunar exploration. Engine concepts proposed to use this propellant have not previously been demonstrated, and the impact on performance from combustion and two-phase flow losses could only be estimated. Therefore, combustion tests were performed for aluminum and aluminum/magnesium alloy powders with oxygen in subscale heat-sink rocket engine hardware. The metal powder was pneumatically injected, with a small amount of nitrogen, through the center orifice of a single element O-F-O triplet injector. Gaseous oxygen impinged on the fuel stream. Hot-fire tests of aluminum/oxygen were performed over a mixture ratio range of 0.5 to 3.0, and at a chamber pressure of approximately 480 kPa (70 psia). The theoretical performance of the propellants was analyzed over a mixture ratio range of 0.5 to 5.0. In the theoretical predictions the ideal one-dimensional equilibrium rocket performance was reduced by loss mechanisms including finite rate kinetics, two-dimensional divergence losses, and boundary layer losses. Lower than predicted characteristic velocity and specific impulse performance efficiencies were achieved in the hot-fire tests, and this was attributed to poor mixing of the propellants and two-phase flow effects. Several tests with aluminum/9.8 percent magnesium alloy powder did not indicate any advantage over the pure aluminum fuel.

Meyer, Mike L.↗
NASA NTRS1991

Thermoelectric properties of hot-pressed fine particulate powder SiGe alloys

A novel material system and its fabrication technique have been defined and applied to the production of SiGe thermoelectric material through the hot pressing of 50-100 A ultrafine particulates into 80/20 SiGe. Relative to conventionally processed SiGe, a reduction of thermal conductivity of up to 40 percent is achieved in conjunction with an enhancement of material figure-of-merit of the order of 10-15 percent.

Beaty, John S.↗
DOE OSTI2024

Characteristics of oxide-dispersion strengthened alloys produced by high-temperature severe deformation

This study is to explore an economically attractive and technically feasible processing method for oxide-nanoparticle strengthened alloys for fusion reactor application. Despite many scientific merits of the advanced oxide-dispersion strengthened (ODS) alloys, such as the nanostructured ferritic alloy (NFA) 14YWT, the only viable production path for a high-quality NFA is the high-power mechanical alloying process. This process is often a multi-day high-speed ball milling of alloy powder with a small quantity of yttria (Y 2 O 3 ) powder, followed by the milled-powder consolidation using extrusion or other methods and additional thermomechanical processing (TMP) for property control. This complex production path, including the low-temperature mechanical alloying in particular, has limited technical advancement toward the cost-effective and scale-up production of ODS alloy components. To overcome such a practical limitation, we proposed to explore alternative low-cost processing routes using traditional thermomechanical processing (TMP) method only. Further, a series of continuous TMP cycles, which were designed to impose high-temperature severe plastic deformation (HT-SPD) conditions to the consolidated powder mixtures, were applied to achieve the effective distribution of oxide particles in nanograin structure and thus desirable mechanical properties. Since the reduced-activation ferritic-martensitic (RAFM) alloy powders (Fe-10Cr and Fe-14Cr alloys with various Y contents) are available in our inventory, we focused to utilize the new solid-state synthesis approach for controlling oxide (oxygen source) dissolution and nanoscale clustering in nanograin structure in those alloys. A combination of powder consolidation at 900 °C and continuous thermomechanical activation at 600 °C yielded two essential ODS alloy microstructure contents–nanograin structure and nanoparticle distribution–and thus demonstrated a good combination of strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development and Additive Manufacturing Deployment in the Area of Aluminum Alloys for AM Powder Production (Final Report)

The overall Science-based Acceleration of the Full Value Stream for Metal Additive Manufacturing (AM): Expedited Powder Development and Additive Manufacturing Deployment (“X-P4AM”) project objective is to drastically reduce the time-to-market barriers for new additive alloys of interest in automotive and aerospace applications, through computational alloy design with rapid screening and down- selection via synthesis of candidate alloys with rapid solidification. The project will also refine the technology in high pressure gas atomization to improve the production of commercial quantities of selected powders with high powder yields and enhanced powder quality. A new aluminum (Al) alloy based on an Al-Ce-X composition, enhanced powder production, and optimized AM build parameterization provided a critical step in widespread adoption of AM technology for automotive applications, in this case. The individual background and capabilities of the Party are ideally suited to the successful execution of this work. The included work enhanced the Contractors’ AM capabilities, a core competency of the Contractors, and developed a close working relationship with the Participant in the area of aluminum powder alloys and their end use.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Electron Beam Melting of Niobium Alloys from Blended Powders

Niobium-based tungsten alloys are desirable for high-temperature structural applications yet are restricted in practice by limited room-temperature ductility and fabricability. Powder bed fusion additive manufacturing is one technology that could be leveraged to process alloys with limited ductility, without the need for pre-alloying. A custom electron beam powder bed fusion machine was used to demonstrate the processability of blended Nb-1Zr, Nb-10W-1Zr-0.1C, and Nb-20W-1Zr-0.1C powders, with resulting solid optical densities of 99+%. Ultimately, post-processing heat treatments were required to increase tungsten diffusion in niobium, as well as to attain satisfactory mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS1982

Advanced powder metallurgy aluminum alloys and composites

The differences between powder and ingot metallurgy processing of aluminum alloys are outlined. The potential payoff in the use of advanced powder metallurgy (PM) aluminum alloys in future transport aircraft is indicated. The national program to bring this technology to commercial fruition and the NASA Langley Research Center role in this program are briefly outlined. Some initial results of research in 2000-series PM alloys and composites that highlight the property improvements possible are given.

W. B. Lisagor↗
DOE OSTI2020

Conductive spinels derived from Co–Mn based alloy precursor for SOFC cathode-side contact application

The utilization of gas-atomized Co–Mn based alloy precursor is a promising approach to lowering the sintering temperature of the spinel contact layer and enhancing its performance. In this work, simulated interconnect/contact/cathode cells are employed to investigate the effects of different metallic precursors (i.e., three Co–Mn based alloy powders and a mixture of Co + MnO 2 powders) on the microstructure and performance of the reactively-sintered MnCo 2 O 4 -based contact layer. While excellent overall electrical performance is observed for all the cells with the four contact precursors during 1000-h testing at 800 °C in air, the cell with the Ce-doped alloy contact precursor shows the lowest cell area specific resistance (ASR) and ASR degradation rate. Cross-sectional observation of the tested cells is conducted to assess the compatibility of the contact layer with adjacent components as well as its effectiveness in reducing the Cr 2 O 3 scale growth and blocking Cr migration from the interconnect to the cathode.

08 HYDROGEN↗
NASA NTRS2024

Short-Term Elevated Temperature Mechanical Performance and Microstructure of A Niobium-Zirconium Alloy Produced via Laser Powder Bed Fusion In-Situ Alloying

Nb-1Zr is a readily fabricable, dispersion-strengthened niobium alloy with improved elevated temperature properties compared to commercially pure niobium. This low to moderate strength niobium alloy is desirable in thermal management systems for fission power and propulsion applications; however, pre-alloyed spherical feedstock for powder-based additive manufacturing processes is generally unavailable. Laser powder bed fusion (L-PBF) in-situ alloying of a Nb-1Zr chemistry was performed using a high-purity niobium feedstock coated with 1 wt% of zirconium-based ceramic compound nano-powders: ZrO 2 , ZrC, and ZrH 2 . The additively manufactured material was mechanically tested at elevated temperatures within a controlled environment in the as-built condition. For comparison, traditionally manufactured wrought feedstock was also tested within an identical environment. Examination of the materials’ microstructure and short-term elevated temperature mechanical response determined: in-situ alloying of spherical Nb powder feedstock with Zr-based ceramic nanoparticles can be successfully implemented; the ZrO 2 addition offered the greatest elevated temperature stability and strength but exhibited brittle behavior; the ZrC addition achieved a balance of room temperature ductility and elevated temperature strength; and the ZrH 2 -modified material had the lowest as-built interstitial content and showed high ductility with mechanical performance most similar to wrought Nb-1Zr.

Niobium Alloy↗
DOE OSTI2021

Sensitivity of additively manufactured AA7075 to variation in feedstock composition and print parameters

Here we developed a combined finite element and CALPHAD based model of the Laser Powder Bed Fusion (LPBF) process for AA7075 alloy that considers the effect of feedstock composition and print parameters. A single-pass of a laser on a layer of AA7075 alloy powder has been considered. Sensitivity of temperature evolution and melt pool geometry to variation in the stoichiometry of the feedstock powder and laser source characteristics have been studied. Our results indicate that deviation (up to 10%) of the feedstock composition from the AA7075 raises the maximum temperature and increases melt pool size. Excess Cu content shows the largest melt pool width and depth among all the cases. The peak temperature is higher than the standard feedstock composition in all cases, except when the Cu concentration is reduced. Increasing the scan power also results in a higher peak temperature and a larger melt pool size. Furthermore, the temperature's rise time increases by lowering the scan speed.

42 ENGINEERING↗
NASA NTRS1990

Elevated temperature crack growth in advanced powder metallurgy aluminum alloys

Rapidly solidified Al-Fe-V-Si powder metallurgy alloy FVS0812 is among the most promising of the elevated temperature aluminum alloys developed in recent years. The ultra fine grain size and high volume fraction of thermally stable dispersoids enable the alloy to maintain tensile properties at elevated temperatures. In contrast, this alloy displays complex and potentially deleterious damage tolerant and time dependent fracture behavior that varies with temperature. J-Integral fracture mechanics were used to determine fracture toughness (K sub IC) and crack growth resistance (tearing modulus, T) of extruded FVS0812 as a function of temperature. The alloy exhibits high fracture properties at room temperature when tested in the LT orientation, due to extensive delamination of prior ribbon particle boundaries perpendicular to the crack front. Delamination results in a loss of through thickness constraint along the crack front, raising the critical stress intensity necessary for precrack initiation. The fracture toughness and tensile ductility of this alloy decrease with increasing temperature, with minima observed at 200 C. This behavior results from minima in the intrinsic toughness of the material, due to dynamic strain aging, and in the extent of prior particle boundary delaminations. At 200 C FVS0812 fails at K levels that are insufficient to cause through thickness delamination. As temperature increases beyond the minimum, strain aging is reduced and delamination returns. For the TL orientation, K (sub IC) decreased and T increased slightly with increasing temperature from 25 to 316 C. Fracture in the TL orientation is governed by prior particle boundary toughness; increased strain localization at these boundaries may result in lower toughness with increasing temperature. Preliminary results demonstrate a complex effect of loading rate on K (sub IC) and T at 175 C, and indicate that the combined effects of time dependent deformation, environment, and strain aging may play a role. Fractography showed that microvoid coalescence was the microscopic mode of fracture in FVS0812 under all testing conditions. However, the nature of the microvoids varied with test temperature and loading rate, and is complex for the fine grain and dipersoid sizes of FVS0812.

Porr, William C., Jr.↗
DOE OSTI2021

Enhanced biomechanical performance of additively manufactured Ti-6Al-4V bone plates

As the global trauma fixation devices market expands rapidly, it is imperative to improve the production of fixation devices through enhanced design accuracy and fit for best performance and maximum patient comfort. Selective laser melting (SLM) is one of the mature additive manufacturing methods, which provides a viable route for the rapid production of such devices. In this work, the ability of SLM to produce near-net-shape parts, as desired for medical implants, was utilized for the fabrication of bone plates from Ti-6Al-4V alloy powder. Martensitic microstructure obtained after the printing of alloy resulted in poor ductility, limiting its application in the field of orthopedics. A specially designed repeated cyclic heating and cooling close to but below the β-transus was used to transform from acicular to a bimodal microstructure without the need for plastic deformation prior to heat treatment for improving the ductility. Bone plates subjected to this heat treatment were mechanically tested by means of tensile and 3-point bend tests and demonstrated large improvement in ductility, and the values were comparable to those similar plates prepared from wrought alloy. Other important properties required for implants were assessed, such as corrosion resistance in simulated body fluid and cytocompatibility in vitro using MC3T3-E1 cells. These results for the bone plate after heat treatment were excellent and similar to those of the additively manufactured and wrought plates. Taken together, the performance of the additively manufactured bone plates after subjecting to heat treatment was similar to those of bone plate manufactured using wrought alloy. These results have important implications for the fabrication of patient-specific metallic orthopedic devices using SLM without compromising their biomechanical performance by subjecting them to a tailored heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Concentric Ring Gas Atomization Die Design for Optimized Particle Production

In partnership with Linde plc (formerly Praxair, Inc.), Ames Laboratory will further develop and commercialize its concentric-ring high pressure gas atomization (CR-HPGA) gas-die technology with a goal to improve the precision of metal powder production in a desired size range and quality. The successful commercialization of this technology could reduce production cost of metal powders and improve reliability of this industrial process, increasing specialty alloy powder availability for new applications and adoption into additive manufacturing and multiple materials sectors. The project scope is to [1] utilize AMES compressible gas flow and melt break-up models to explore a wide swath of parameter space available for the CR-HPGA technology, identifying the most promising gas-die designs for fabrication, [2] verify and optimize the new gas-die design, fabricate it and select preferred operating parameters by gas-only flow imaging and aspiration pressure measurements, down-selecting gas compositions and atomization parameters for full scale testing, [3] perform pilot-scale atomization trials with Al and/or Cu alloys of a new CR-HPGA gas-die at selected parameters, [4] evaluate gas-die performance by comparing resulting powder size distribution and powder quality attributes with equivalent powders made by conventional close-coupled HPGA technology, and [5] assess (through Praxair partnership) reduction in operational costs of new CR-HPGA gas-die through the use of an inert gas recovery/recycling system. In partnership with Praxair, Inc., the team, led by Ames Laboratory senior metallurgist Iver Anderson, intend to demonstrate the performance of an optimized CR-HPGA gas-die design in a pilot scale atomizer and better understand the design and operational controls to increase overall benefits for precision metal powder production.

42 ENGINEERING↗
NASA NTRS1988

Dispersion strengthening of precipitation hardened Al-Cu-Mg alloys prepared by rapid solidification and mechanical alloying

Several Al-4Cu-1Mg-1.5Fe-0.75Ce alloys have been processed from either rapidly solidified or mechanically alloyed powder using various vacuum degassing parameters and consolidation techniques. Strengthening by the fine subgrains, grains, and the dispersoids individually or in combination is more effective when the alloys contain shearable precipitates; consequently, the strength of the alloys is higher in the naturally aged rather than the artificially aged condition. The strengths of the mechanically alloyed variants are greater than those produced from prealloyed powder. Properties and microstructural features of these dispersion strengthened alloys are discussed in regards to their processing histories.

Gilman, P. S.↗