Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ash effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Unveiling Feedstock Variability: Insights into Corn Stover Conversion - Part I: Physicochemical Properties and Self-Degradation

Transforming agricultural waste into biofuels and bioproducts is crucial to advancing a low-carbon bioeconomy. However, the inherent variability in the composition and quality introduces uncertainties in the conversion efficiency and poses challenges in process development. Through integrating a high-throughput conversion system, material characterization techniques, and advanced data analysis tools, this study investigates the variability of corn stover and its subsequent impacts on carbohydrate conversion. The findings reveal that indoor storage substantially reduces the moisture and ash content and soil contamination, while other properties remain largely unchanged. Self-degradation due to microbial activity during storage decreases the carbohydrate content of corn stover but enhances glucose and xylose yields. A negative correlation is observed between sugar yields and lignin content across samples with varying ash and moisture content. The inhibitory effect of lignin diminishes in self-degraded samples likely due to the disrupted cell wall structure. Although self-degradation slightly increases cellulose crystallinity, no strong correlation was observed between the crystallinity and sugar yield. Hot water pretreatment under mild conditions effectively mitigates inherent variability, consistently improving the sugar yield from corn stover by up to 50%. By elucidating the feedstock variability and its impact on convertibility, these findings offer valuable insights into appropriate feedstock handling and management, highlighting potential strategies to address variability challenges.

09 BIOMASS FUELS↗
DOE OSTI2023

Diesel Particulate Filter Durability Performance Comparison Using Metals Doped B20 vs. Conventional Diesel Part II: Chemical and Microscopic Characterization of Aged DPFs

This project's objective was to generate experimental data to evaluate the impact of metals doped B20 on diesel particle filter (DPF) ash loading and performance compared to that of conventional petrodiesel. The effect of metals doped B20 vs. conventional diesel on a DPF was quantified in a laboratory controlled accelerated ash loading study. The ash loading was conducted on two DPFs - one using ULSD fuel and the other on B20 containing metals dopants equivalent to 4 ppm B100 total metals. Engine oil consumption and B20 metals levels were accelerated by a factor of 5, with DPFs loaded to 30 g/L of ash. Details of the ash loading experiment and on-engine DPF performance evaluations are presented in the companion paper (Part I). The DPFs were cleaned, and ash samples were taken from the cleaned material. X-ray Fluorescence (XRF), X-Ray Photoelectron Spectroscopy (XPS) and X-Ray Diffraction (XRD) were conducted on the ash samples. Core samples were taken from the cleaned DPF and were subjected to scanning electron microscope energy dispersive x-ray spectroscopy (SEM-EDS) and XRF analysis. A comparison of the data from the two DPFs is presented. The XRD and XPS analysis showed that the compounds present in the ash from the two DPFs were nearly identical, though differing in concentrations. CaSO4 was the biggest component of the ash from both DPFs. The metals doped B20 fuel resulted in ash with similar characteristics to that deposited by the lube oil and did not appear to have any deleterious physical effects on the DPF substrate (did not penetrate the substrate).

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2025

Hydrogen-rich syngas production from the steam co-gasification of low-density polyethylene and coal refuse

Gasification provides a promising pathway for transforming waste materials into valuable products, such as fuels and chemicals. Here, this study investigates the steam co-gasification of low-density polyethylene (LDPE) and compressed thickener underflow, representative of coal refuse (CR), in a drop tube reactor. The effects of feed blend ratio (0–100 wt% LDPE) and temperature (800–1000 °C) on syngas composition, tar formation, and process efficiency are examined. The high volatility of LDPE makes it more reactive than CR but also promotes the formation of 2–7 ring aromatic tars. Increasing temperature improves carbon conversion efficiency (CCE), cold gas efficiency (CGE), and syngas yield, although the lower heating value (LHV) of syngas decreases. Hydrogen is the dominant gas product, reaching 59 vol% with the H 2 /CO molar ratio ranging from 2.27 to 4.74. Synergistic effects from alkali and alkali earth metals (AAEMs), particularly K and Ca, in CR ash enhance syngas yield by catalyzing char gasification and tar cracking. Hematite (Fe 2 O 3 ) and ash from sub-bituminous/bituminous coals are explored as tar reforming catalysts. Fe 2 O 3 achieves 100 % tar reforming efficiency, while coal ash, with a lower Fe 2 O 3 content (15 wt%), is less effective at cracking polycyclic aromatic hydrocarbons, particularly naphthalene. These findings demonstrate the flexibility of co-gasification, allowing precise tuning of syngas characteristics for specific downstream applications. Further optimization of waste-derived catalysts could enhance the economic viability of gasification in waste-to-energy processes.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2026

A Data-driven Phytotechnology Framework for Identification and Remediation of Leached-Metals-Contaminated Soil Near Coal Ash Impoundments

This project developed and evaluated advanced remote sensing and machine learning approaches to identify, monitor, and address environmental contamination associated with coal combustion residual (CCR) impoundments and landfills at coal-fired power plants. In Phase I, historical and multi-temporal Sentinel-2 satellite imagery, groundwater monitoring data, and environmental variables were integrated to detect vegetation stress potentially caused by toxic metal leaching from coal ash disposal sites. Multiple vegetation and biophysical indices were analyzed to determine their effectiveness in identifying abnormal vegetation growth patterns linked to contamination. Results from case studies conducted at coal ash–impacted power plant sites in North Carolina and Virginia demonstrated that satellite-based vegetation monitoring can serve as an effective early indicator of environmental stress associated with metals such as arsenic, cadmium, cobalt, lead, lithium, radium, and thallium.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Characteristics of the sub-micron ash aerosol generated during oxy-coal combustion at atmospheric and elevated pressures

This paper is concerned with the effect of pressure on the particle size distribution and the size-segregated composition of the sub-micron ash aerosol created during oxy-coal combustion under near practical self-sustaining combustion conditions. The problem is important because pressurized oxy-coal combustion has been proposed as one promising technology to minimize CO 2 emissions. Sub-micron ash plays a major role in ash deposition mechanisms, which, in turn, can control boiler performance. In this work, the same bituminous coal was burned at pressures of 1, 8 and 15 bar in O 2 /CO 2 environments. Here, tests employed a 100 kW (rated) oxy-fuel combustor (OFC) operated at atmospheric pressure (1 bar) and a 300 kW (rated) entrained-flow pressurized reactor (EFPR) at elevated pressures (8 and 15 bar). Although these tests were conducted under near practical combustion conditions, confounding effects of peak flame temperature variations were minimized for the 1 bar and 15 bar tests, allowing the role of elevated pressure to be isolated. For the EFPR tests, a specially designed sampling system was used to sample sub-micron ash aerosols from the pressurized combustor and is described in detail. Results showed that at the same peak temperature but higher pressure, the fractions of ash aerosol partitioned into the PM 0.6 and PM 1 size fractions were greatly diminished. Moreover, elevated pressures caused significant changes in the composition of the (size-segregated) sub-micron aerosol, especially in its alkali content, which increased significantly. Examination of fractions of each element that ended up in the sub-micron fume suggested that, at constant temperature, the effect of pressure on vaporization of semi-volatile metals was very different from that on the release into the gas phase of non-volatile metals and could not be explained by equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Influence of MXene termination groups on hydrogen interactions

MXenes are a relatively new class of nanomaterial consisting of alternating layers of transition metals and carbon or nitrogen, capped off on either end by terminal groups, usually from the P-block. They have been considered for a wide range of purposes, including hydrogen storage. In this study, thermogravimetric analysis and mass spectrometry residual gas analysis are performed on Ti 3 C 2 T x and Ti 2 CT x to characterize their terminal groups. The hydrogen absorption capabilities of the heat-treated samples are measured using a Sievert apparatus and compared against untreated samples. This reveals that, during heating, the MXenes lose hydrogen, water, fluoride, hydrofluoric acid, and carbon dioxide. Isothermal absorption measurements suggest that the removal of termination groups might improve hydrogen uptake kinetics at high temperatures, but has little effect at room temperatures.

08 HYDROGEN↗
DOE OSTI2025

Thermal shock resistance of lightweight cements developed for geothermal conditions

Cements are a critical component in well construction, as they act to prevent well fluid and gas escape, prevent corrosion of the casing, and strengthen the wellbore to prevent deformation. Under the high temperature/pressure conditions common in geothermal systems, the injection of cold water for energy production is expected to induce cyclic damage to the borehole cement through the rapid temperature fluctuations. These “thermal shocks” are expected to cause casing shrinkage, annulus formation, and cement tensile stresses. To understand the effect of cold water injection on the wellbore environment, a set of rock-cement-steel samples were created to simulate the structure of a geothermal well. Lightweight thermally-insulating cement blends were tested under thermal shock conditions in this study. In each test, the samples were pressurized to an effective pressure of ~3.5 MPa and placed at high temperatures. Thermal shocks were performed by injecting cold water (~10-15 °C) through the samples at a constant rate while keeping the samples at high temperatures until the sample temperature stopped decreasing and deformation ceased. Eight thermal shock tests were conducted with each sample – two at 100 °C and six at 200 °C. Post-tests analysis was then conducted by cutting open each sample to examine the damage in each component of the simulated wellbore. Experimental results suggest that all samples experienced similar degrees of axial and lateral contraction during cold water injection, but for the most part this contraction is recoverable when injection halts. Post-test analysis revealed that fly ash cenosphere pre-treatment had the best effect on improving thermal shock resistance in the cement blends. Thermomechanical modeling of likely stress paths experienced by the cements during heating/cooling cycles shows that elasto-plastic cement constitutive behavior results in most plastic strain occurring during the initial heating steps, with mostly elastic strain occurring during the thermal shock cycles. In conclusion, this agrees with experimental evidence, suggesting that cement damage from shocking occurs via other mechanisms such as chemical alteration, corrosion, and fatigue.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Thermochemical Transformation of Calcium during Biomass Burning and the Effects on Postfire Aqueous Dissolution of Macronutrients

Calcium is commonly the most abundant element in fire residues and its speciation largely determines the geochemical properties of fire residues and their effects on postfire soil chemistry. To explore the effects of biomass composition and fire conditions on ash Ca speciation, this study characterizes the speciation of Ca in charcoal and ash samples that were derived from different plant compartments and thermal conditions, using Ca K-edge X-ray absorption near edge spectroscopy. Results showed that biomass contains abundant organic Ca complexes, which were mineralized into fairchildite and calcite after heating at 450 to 600 °C and then CaO, as temperature increased to 750 °C. Apatite could be an abundant Ca species in fire residues if the Ca/P molar ratio of the biomass is small (<2). The mineralization of organic Ca to the identified Ca minerals during burning was negligibly affected by the oxygen level. Calcium speciation in prescribed fire residues resembled that of biomass ash burned at 550 °C with similar Ca/P molar ratios. Batch experiments showed that macronutrients (Ca, Mg, K, and P) were differentially released, as a result of different solubility of minerals in ashes and reprecipitation of minerals. The aqueous solubility of Ca, Mg, and P decreased as pH increased from 5 to 9, while K showed no pH dependency and was almost completely soluble. Results from this study improve our understanding of the chemistry of fire residues and their geochemical behaviors, which can help evaluate the impact of fire on postfire soil properties and macronutrient cycling.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mitigation Methods for Piperazine Oxidation in Post-Combustion Carbon Capture

Piperazine is a promising second-generation solvent for amine scrubbing in post-combustion CO2 capture. However, the oxidative degradation of PZ can cause environmental problems and economic loss. This work presents the effects of two mitigation methods: carbon treating and N2 sparging, on the PZ oxidation in long-term operations. The species and their respective quantities adsorbed by the activated carbon were tested in a bench-scale device. The carbon was then tested in the High Temperature Oxidation Reactor (HTOR), where the solvent oxidizes at a reasonably fast rate. Pilot plant campaigns were also performed at the UT Austin SRP and the National Carbon Capture Center (NCCC) and the effects were verified. When dissolved Fe is removed by carbon treating or other methods, available soluble Fe in the system dissolves and replaces the dissolved Fe. Therefore, all available Fe and ligands need to be removed for the mitigation to be effective. The sources of soluble Fe include fly ash and the corrosion of stainless steel, and the ligands are degradation products. 8 All PZ degraded solvents have two absorbance peaks at 320 nm and 538 nm. The 320 nm peak is caused by dissolved metals, especially Fe, complexed by degradation products. The 320 nm peak is related to the amine degradation level and can be used as a simple and efficient method to estimate the amine degradation rate. The pilot plant data suggest that NO2 can oxidize PZ significantly, possibly through radical reactions. 0.01 mmol/kg-hr absorption of NO2 increased the PZ oxidation rate from 1.2 mmol/kg-hr to 2.5 mmol/kg-hr.

Yuying, Wu↗
DOE OSTI2021

Reburning of Animal Waste Based Biomass with Coals for NO x Reduction, Part II: Dairy Biomass (DB) and Coal–DB Blends

Concentrated animal feeding operations (both slaughter and dairy cattle) lead to land, water, and air pollution if waste storage and handling systems are not effectively managed. At the same time, cattle biomass (CB), which includes both slaughter/feedlot biomass (FB) and dairy biomass (DB), have the potential to be a source of green energy at coal-fired power plants. Part I presented results on NOx reductions with pure FB or Coal: FB blends as reburn fuels. Part II deals with results from reburning with pure DB or Coal: DB blends as reburn fuels. A mixture of NG with a small amount of NH3 was used to generate the baseline NOx of 400–420 ppm (or 185–194 g/GJ). NOx emissions were found to be reduced by as much as 96% when reburning with FB. The effects of reburn fuel type, equivalence ratio (ER RBZ ) in the reburn zone, vitiated air, several injection configurations of reburn fuel and initial NO concentrations on NOx emissions were investigated. The ER RBZ shows a significant effect on the NOx reduction. The 20% heat input by reburning was the better operating condition for the long-term operation due to its ash production. The results reveal that reburn with DB fuels is an effective technology for NOx emission control when the initial NOx emission is higher than 275 ppm (or 127 g/GJ or 0.3 lb/MMBtu).

09 BIOMASS FUELS↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2021

Integration of Air Classification and Hydrothermal Carbonization to Enhance Energy Recovery of Corn Stover

Air classification (AC) is a cost-effective technology that separates the energy-dense light ash fraction (LAF) from the inorganic-rich high ash fraction (HAF) of corn stover. HAF could be upgraded into energy-dense solid fuel by hydrothermal carbonization (HTC). However, HTC is a high-temperature, high-pressure process, which requires additional energy to operate. In this study, three different scenarios (i.e., AC only, HTC only, and integrated AC–HTC) were investigated for the energy recovery of corn stover. AC was performed on corn stover at an 8 Hz fan speed, which yielded 84.4 wt. % LAF, 12.8 wt. % HAF, and 2.8 wt. % below screen particles. About 27 wt. % ash was reduced from LAF by the AC process. Furthermore, HTC was performed on raw corn stover and the HAF of corn stover at 200, 230, and 260 °C for 30 min. To evaluate energy recovery, solid products were characterized in terms of mass yield, ash yield, ultimate analysis, proximate analyses, and higher heating value (HHV). The results showed that the energy density was increased with the increase in HTC temperature, meanwhile the mass yield and ash yield were decreased with the increase in HTC temperature. Proximate analysis showed that fixed carbon increased 18 wt. % for original char and 27 wt. % for HAF char at 260 °C, compared to their respective feedstocks. Finally, the hydrochar resulting from HAF was mixed with LAF and pelletized at 180 bar and 90 °C to densify the energy content. An energy balance of the integrated AC–HTC process was performed, and the results shows that integrated AC with HTC performed at 230 °C resulted in an additional 800 MJ/ton of energy recovery compared to the AC-only scenario.

09 BIOMASS FUELS↗
DOE OSTI2021

Comparison on the properties of ITZs in fly ash-based geopolymer and Portland cement concretes with equivalent flowability

Highlights: • Modelled ITZs can effectively avoid the effects caused by different factors and test locations of ITZ. • ITZ properties of PC and geopolymer concretes are compared based on equivalent flowability of binders. • Geopolymer ITZ exhibits stronger bonding than that of PC, and higher mechanical properties than geopolymer paste. • Strong ITZs in geopolymer concrete are attributed to the layer of gel-rich paste with dense microstructures. • Elastic modulus and hardness properties of ITZs in PC concrete are increased due to the CH crystals. This paper aims to compare the properties of interfacial transition zones (ITZs) in Portland cement (PC) concrete and geopolymer concrete. Portland cement and geopolymer pastes were designed with the equivalent flowability to provide similar mix and casting condition of ITZs. Two types of modelled ITZs were prepared to facilitate the nanoindentations across ITZs, microstructural characterization, and comparison on the properties of ITZs with less influential factors. The results showed that the interfacial bonding of ITZs between geopolymer matrix and aggregate is relatively stronger than the counterpart in the PC concrete. There is a high amount of crystalline hydration products in the ITZs of PC concrete, but a layer gel-rich paste with denser microstructures in the ITZs of geopolymer concrete. Additionally, the interface morphology and nanoindentation analysis indicate that the property of ITZs in the modelled geopolymer concrete is not poorer than that of the corresponding geopolymer paste.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A simplified integrated framework for predicting the economic impacts of feedstock variations in a catalytic fast pyrolysis conversion process

Feedstock attributes of lignocellulosic biomass, such as particle size, compositional makeup, and moisture content, can vary substantially even within pre-processed materials and have a significant effect on conversion in fast pyrolysis-based processes. However, the economic impacts of these attributes are not well understood. To address this, biomass deconstruction phenomena captured with a versatile particle-scale simulation were linked to techno-economic impacts via reduced-order models. Parametric analysis of the particle-scale model, which was validated using literature data, was used in combination with multiple linear regression models to develop correlations between feedstock attributes and yields of pyrolysis oil, gas, and char. Yields were then correlated with the minimum fuel selling price (MFSP) using a techno-economic model, bridging the gap between physics-based biomass conversion simulations and predictions of MFSP for a catalytic fast-pyrolysis process. Empirical correlations derived from the literature regarding the impact of mineral matter (ash) on oil yield were also considered. The model correlations deployed in the integrated framework capture the impacts of variation in feedstock attributes on the MFSP. Variations in ash were shown to have the biggest impact, varying MFSP by -13%/+22% due to catalytic effects and lower relative amounts of convertible lignocellulosic material. It was also found that, if ash can be controlled to low levels, the increased extractives in forest residues can help compensate for some yield losses associated with increased ash. As a result, other inputs considered (particle size, moisture content, and reactor temperature) had relatively negligible effects on process economics within the ranges analyzed considering particle-scale effects alone.

BIOMASS FUELS↗
DOE OSTI2021

Optimum concentration of fly ash nanoparticles to stabilize CO 2 foams for aquifer and soil remediation

Contamination caused by non-aqueous phase liquids (NAPLs) in aquifers and soil is an important challenge that requires effective remediation techniques. One potential approach is through the use of CO 2 foams to displace NAPLs from permeable media. CO 2 foams generated only by surfactants are not stable enough for the efficient removal of NAPLs contamination. This shortcoming may be alleviated via the use of nanoparticles (NPs)-surfactant mixtures as a stabilizing agent. This work focuses on the evaluation of the optimum concentration of fly ash nanoparticles for stabilizing CO 2 foam with the combined action of the surfactant. The performance of this foam is evaluated in remediating a contaminated 41 mm × 36 mm surrogate permeable medium in a microfluidic device. Mixtures of fly ash, a by-product of coal-burning power plants, and alpha-olefin sulfonate (AOS) and lauramidopropyl betaine (LAPB) surfactants are used to generate stable foams. The results show that a 1000 mg/L AOS-LAPB surfactant solution along with 1000 mg/L of fly ash NPs produces the best performance. Formation of deposits in the matrix is observed. These deposits, which are more prominent at higher NP concentrations, appear to adversely affect displacement, displacement efficiency and remediation of the medium. This study demonstrates that using fly ash nanoparticles and optimizing their concentration can effectively stabilize CO 2 foams and improve the displacement efficiency for aquifer and soil remediation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Towards ternary binders involving limestone additions — A review

The review summarises literature to examine the transition from portland limestone cement system to composite ternary binder systems involving limestone. Interest in limestone addition as an ideal component in multicomponent binder systems has surged as evident from the large volume of literature published in the recent past. A ternary blended system, with co-substitution of limestone, has the potential to complement the reaction of the supplementary cementitious materials (SCMs). The direct addition of limestone powder helps to attain higher substitution levels of portland cement clinker, improve early age properties, and supplement SCM's reactivity. However, the dilution of hydrates could hamper the long-term benefits. In this review, the interaction of fine limestone is classified and elaborated under two broad umbrellas: physical and chemical interactions. The physical interactions can manifest in three ways, namely, filler action, shearing action and improved packing, which alters reaction rate and extent at early ages. The chemical interactions also modify the reaction kinetics and phase assemblage due to nucleation of C-S-H on calcite surfaces, preservation of the ettringite phase and formation of carboaluminates. Two different forms of carboaluminate hydrates — hemicarboaluminate and mono-carboaluminate can be present in the hydrate matrix depending on the balance between carbonate ions and aluminates in the pore solution. Several factors such as replacement level, particle size, choice of SCM, its reactivity and reactive aluminates content, sulphate levels, curing temperature, and duration of curing can control the carboaluminate formation, reaction degree of SCMs and chemical interaction from limestone additions. A combination of physical and chemical effects makes fine limestone a potential material for co-substitution with aluminosilicate based SCMs, mainly fly ash, slag, and calcined clay. In this review, the factors affecting limestone-SCM composites are summarised based on a detailed literature survey. The effects of SCM-limestone cement composites on hydration kinetics, reaction chemistry, the reactivity of SCMs, the stability of hydrated phases, and contribution to the physical structure development and macroscopic properties by evaluating hydration and mechanical properties are discussed. The importance of AFm (Al{sub 2}O{sub 3}–Fe{sub 2}O{sub 3}-mono) phases in various deterioration mechanisms in concrete and their influence on performance characteristics in different exposure environment is critically appraised.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Sustainable extraction of rare earth elements from coal fly ash leachates using a recyclable ionic liquid

The growing demand for rare earth elements (REEs) has prompted interest in their recovery from alternative sources such as coal fly ash (CFA). This study explores the ionic liquid (IL) betainium bis(trifluoromethylsulfonyl)imide, [Hbet][Tf 2 N], for selective extraction of REEs from leachates of a Class C CFA. While previous studies have demonstrated the effectiveness of using [Hbet][Tf 2 N] to extract REEs from different types of CFA in direct ash-IL systems, this study investigates four CFA leachates prepared using HCl, HNO 3 , H 2 SO 4 , and citrate. Extraction experiments were conducted across varying pH levels and with additives such as ascorbic acid and betaine. Among the systems tested, [Hbet][Tf 2 N] achieved REE recoveries of 51% and 47% from the HCl and citrate leachates, respectively, comparable to 49% REE recovery in ash-IL extraction. Co-extraction of bulk elements was significantly reduced in the leachate-IL systems. Optimal REE extraction occurred near pH 11, and addition of ascorbic acid effectively suppressed iron co-extraction without compromising REE recovery. Recycling experiments demonstrated that [Hbet][Tf₂N] retains its performance over five cycles with manageable losses. These results reveal the promise of [Hbet][Tf 2 N] for effectively recovering REEs from leachates of solid wastes, highlighting its applicability as a sustainable strategy for other aqueous REE feedstocks.

chemistry↗
DOE OSTI2021

Divergence in heritable life history traits suggests potential for local adaptation and trade‐offs associated with a coal ash disposal site

Abstract Globally, human activities have resulted in rapid environmental changes that present unique challenges for wildlife. However, investigations of local adaptation in response to simultaneous exposure to multiple anthropogenic selection pressures are rare and often generate conflicting results. We used an in situ reciprocal transplant design within a quantitative genetic framework to examine how adaptive evolution and phenotypic plasticity contribute to the persistence of an amphibian population inhabiting an environment characterized by high levels of multiple toxic trace elements. We found evidence of phenotypic divergence that is largely consistent with local adaptation to an environment contaminated with multiple chemical stressors, tied to potential trade‐offs in the absence of contaminants. Specifically, the population derived from the contaminated environment had a reduced risk of mortality and greater larval growth and in the contaminated environment, relative to offspring from the naïve population. Further, while survival in the uncontaminated environment was not compromised in offspring from the contaminant‐exposed population, they did show delayed development and reduced growth rates over larval development, relative to the naïve population. We found no evidence of reduced additive genetic variation in the contaminant‐exposed population, suggesting long‐term selection in a novel environment has not reduced the evolutionary potential of that population. We also saw little evidence that past selection in the ASH environment had reduced trait plasticity in the resident population. Maternal effects were prominent in early development, but we did not detect any trends suggesting these effects were associated with the maternal transfer of toxic trace elements. Our results demonstrate the potential for adaptation to multiple contaminants in a wild amphibian population, which may have facilitated long‐term persistence in a heavily impacted environment.

59 BASIC BIOLOGICAL SCIENCES↗