Search NASA⌕ Search

SEARCH · Search NASA

Results for “BLI”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗
NASA NTRSDate not supplied

USM3D-ME Analyses Performed in Support of a Wind Tunnel Test of a Boundary-Layer Ingestion Configuration

Boundary Layer Ingestion (BLI) has been proposed as a technology with the potential to decrease fuel burn. However, one major concern for BLI configurations is the potential degradation of the flow quality, both on the airframe and at the fan face, resulting from the tightly integrated propulsor. A wind tunnel test was performed in the National Transonic Facility (NTF) at the NASA Langley Research Center to investigate the flow quality ingested by a tail cone thruster configuration, similar to the Single Aisle Turboelectric Aircraft Concept with Aft Boundary Layer Ingestion (STARC-ABL). The wind tunnel model was a modified version of the Common Research Model (CRM) to include an aft-mounted, flow-through propulsor. The experimental data obtained from the wind tunnel test provide insight into the flow and enables an assessment of the accuracy of the USM3D-ME flow solver for predicting the flow at the fan face, which will be crucial for fan design purposes. Both grid refinement and turbulence model studies were performed for the Clean and Cruise MFP configurations at the condition corresponding to ReMAC = 5 million, Mach = 0.8, and alpha = 2 deg. The selected grid refinement level and turbulence model were then used to perform simulations over the range of conditions considered in the NTF wind tunnel test. The condition sweep comparisons illustrate favorable agreement with the experimental data over the entire range of conditions and for all Mass Flow Plug (MFP) configurations. The largest differences were observed for the Idle MFP configuration, with approximately 3% difference observed between USM3D-ME and the experimental data. Future work should investigate the impact of higher fidelity turbulence models and grid adaptation on the USM3D-ME predictions.

CRM↗
DOE OSTI2025

Xylanolytic metabolism is regulated by coordination of transcription factors XynR and XylR in extremely thermophilic Caldicellulosiruptorales

ABSTRACT Global transcription factors (TFs) control metabolic processes in bacteria to efficiently utilize available carbon. The orderCaldicellulosiruptoraleshas drawn interest due to the ability of its members to degrade components of lignocellulosic biomass. Regulatory reconstruction ofAnaerocellum (f. Caldicellulosiruptor) besciiidentified two major global transcription factors for xylan utilization, XynR and XylR, and the corresponding putative transcription factor binding sites. Recombinant versions of XynR (LacI family) and XylR (ROK family) were subjected to fluorescence polarization (FP) and biolayer interferometry (BLI) analysis to confirm the predicted binding sites. Four XynR sites and two XylR sites were validated, accounting for 20 of 26 genes regulated by XynR and six of seven genes regulated by XylR. Bioinformatic analysis of the individual genes controlled by the two regulators showed an inter-dependent scheme for xylan conversion; the transport of xylooligosaccharides (XOS) is dependent on XylR, while enzymes responsible for hydrolysis are controlled by both regulators. For xylose catabolism by the xylose isomerase-xylulose kinase pathway, regulation is also split, with XylR controlling xylose isomerase and XynR controlling xylokinase. The XynR/XylR regulator pair withinA. besciiis conserved in all sequenced species ofCaldicellulosiruptorales, suggesting similarities in regulating linear xylan conversion. In other xylanolytic thermophiles, XylR homologs control xylan degradation, compared to just 6 out of 26 genes forA. bescii. These results show that two separate regulatory schemes (dual repression) are coordinated byA. besciito effectively regulate the hemicellulose inventory and xylan catabolism. IMPORTANCE To take full advantage of extreme thermophiles as platform metabolic engineering microorganisms, the tools for genetic manipulation must be further developed, and strategies that exploit a better understanding of metabolic regulation need to be discerned.Anaerocellum bescii, the most studied of the extremely thermophilic fermentative anaerobic bacteria that can utilize microcrystalline cellulose, can degrade microcrystalline cellulose and hemicellulose and has been metabolically engineered to convert the resulting sugars to products such as ethanol and acetone. For xylan, in particular, two major global transcription factors (TFs), XynR and XylR, play a role in sugar metabolism, although their predicted regulatory interdependence from bioinformatics analysis has not been elucidated experimentally. Here, fluorescence polarization (FP) and biolayer interferometry (BLI) were used to explore this issue to support metabolic engineering efforts aimed at improving carbohydrate processing to industrial chemicals.

Biotechnology & Applied Microbiology↗
NASA NTRS2010

Inlet Flow Control and Prediction Technologies for Embedded Propulsion Systems

Fail-safe inlet flow control may enable high-speed cruise efficiency, low noise signature, and reduced fuel-burn goals for hybrid wing-body aircraft. The objectives of this program are to develop flow control and prediction methodologies for boundary-layer ingesting (BLI) inlets used in these aircraft. This report covers the second of a three year program. The approach integrates experiments and numerical simulations. Both passive and active flow-control devices were tested in a small-scale wind tunnel. Hybrid actuation approaches, combining a passive microvane and active synthetic jet, were tested in various geometric arrangements. Detailed flow measurements were taken to provide insight into the flow physics. Results of the numerical simulations were correlated against experimental data. The sensitivity of results to grid resolution and turbulence models was examined. Aerodynamic benefits from microvanes and microramps were assessed when installed in an offset BLI inlet. Benefits were quantified in terms of recovery and distortion changes. Microvanes were more effective than microramps at improving recovery and distortion.

McMillan, Michelle L.↗
NASA NTRS2010

Optimal Flow Control Design

In support of the Blended-Wing-Body aircraft concept, a new flow control hybrid vane/jet design has been developed for use in a boundary-layer-ingesting (BLI) offset inlet in transonic flows. This inlet flow control is designed to minimize the engine fan-face distortion levels and the first five Fourier harmonic half amplitudes while maximizing the inlet pressure recovery. This concept represents a potentially enabling technology for quieter and more environmentally friendly transport aircraft. An optimum vane design was found by minimizing the engine fan-face distortion, DC60, and the first five Fourier harmonic half amplitudes, while maximizing the total pressure recovery. The optimal vane design was then used in a BLI inlet wind tunnel experiment at NASA Langley's 0.3-meter transonic cryogenic tunnel. The experimental results demonstrated an 80-percent decrease in DPCPavg, the reduction in the circumferential distortion levels, at an inlet mass flow rate corresponding to the middle of the operational range at the cruise condition. Even though the vanes were designed at a single inlet mass flow rate, they performed very well over the entire inlet mass flow range tested in the wind tunnel experiment with the addition of a small amount of jet flow control. While the circumferential distortion was decreased, the radial distortion on the outer rings at the aerodynamic interface plane (AIP) increased. This was a result of the large boundary layer being distributed from the bottom of the AIP in the baseline case to the outer edges of the AIP when using the vortex generator (VG) vane flow control. Experimental results, as already mentioned, showed an 80-percent reduction of DPCPavg, the circumferential distortion level at the engine fan-face. The hybrid approach leverages strengths of vane and jet flow control devices, increasing inlet performance over a broader operational range with significant reduction in mass flow requirements. Minimal distortion level requirements are met using vanes alone, avoiding engine stall and increasing robustness of this hybrid inlet flow control approach. This design applies to aerospace applications needing flush-mounted boundary-layer-ingesting inlets.

Allan, Brian↗
NASA NTRS2013

Computational Assessment of the Benefits of Boundary Layer Ingestion for the D8 Aircraft

To substantially reduce the fuel burn of future commercial transportation aircraft, the boundary layer ingestion idea is investigated. The idea is that an engine placed in the wake of the aircraft it is propelling is more efficient than a conventional engine placement under the wing or on pods mounted to the rear of the fuselage. The top, rear of the fuselage is thus designed to act as a diffuser such that the engines can be placed there with a minimal nacelle. The boundary layer thickens over the rear of the fuselage such that a large portion of it is ingested by the fan. To assess whether the boundary layer ingesting (BLI) engine placement is indeed advantageous, a study of the nacelle aerodynamics is carried out using Overflow, a viscous CFD flow solver that uses overset meshes. The computed forces and moments are compared to a wind tunnel experiment for validation. Some aspects of the design are verified using the simulation results. Finally, the effect of the nacelle placement is assessed by comparing the BLI nacelle configuration to a podded nacelle configuration and to the unpowered (without nacelles) aircraft.

aircraft↗
NASA NTRS2017

Approach to Modeling Boundary Layer Ingestion Using a Fully Coupled Propulsion-RANS Model

Although boundary layer ingestion (BLI), or wake ingestion, is commonly applied in marine propulsion applications, it has not yet seen wide-spread adoption in aircraft applications. However, recent studies have predicted that BLI offers a potential for a 10 reduction in aircraft fuel burn, even on a fairly traditional aircraft configuration. This dramatic reduction in fuel burn is achieved via tight integration of the propulsion system and airframe aerodynamics, but actually realizing such large performance gains will require modifying the aircraft design process to account for this integration. Traditionally, in aircraft design, the airframe and the propulsion system are designed separately and then the engine sizing is managed with a rubber-engine approach. This works when the propulsion system is placed in the free-stream air, away from the aerodynamic influence of the airframe, and it is reasonable to assume that small changes to either system won't have a strong impact on the other.

propulsion↗
NASA NTRS2018

Conceptual Aerodynamic Design of a Tail-Cone Thruster System Under Axi-Symmetric Inlet Distortion

This paper presents a conceptual design of a tail-cone thruster system which is operating under an axisymmetric inlet distortion. An effort to realize the targeted fuel burn saving that was proposed in NASA's STARC_ABL aircraft design is made through a CFD (Computational Fluid Dynamics)-based design approach. This method employs three iterative steps to exploit the CFD tools until the design requirements are met: a quasi-2D through-flow model to design the fan/EGV (Exit Guide Vane), a 3-D RANS (Reynolds Averaging Navier-Stokes) simulation of the single blade row to account for the inlet/fan and the EGV/nozzle interaction, and a 3-D RANS simulation of the airframe with a propulsor installed - propulsion airframe integration (PAI). The design requirements which include the thrust, and shaft power of the propulsor are matched throughout the evaluations coming from two CFD domains, i.e., the turbo-machinery and the PAI. During the switch between these different computational domains, the inlet and exit profiles are matched via the correction factors of the body-force model. The present tail-cone thruster (TCT) aerodynamic design leverages a low-pressure ratio fan (FPR=1.2 to approximately 1.25) of which the camber-line angles are predicted by a quasi-2D through-flow model. The quasi-2D model is derived to analyze the radially distorted flow resulting from the ingested boundary layer at the inlet. It also estimates the appropriate velocity vectors of the metal angles of the fan and EGV which is subjected to different types of vortex at the fan exit. The baseline geometry is revisited and its internal flow-path and exhaust cone are redesigned to illustrate the strong correlation among the components of the propulsor in the PAI domain. The peak efficiency point of the fan/EGV with respect to the blade counts, also known as solidity, and rotational speed is chosen for the cruise condition via parametric studies. The corresponding performance maps are presented. The resulting performance metrics of the new conceptual design of the BLI (Boundary Layer Ingestion) propulsor are analyzed and compared with these of the baseline in the PAI aspect. Finally, ideas of the CFD based design of a BLI propulsor are discussed based on the observations drawn from the numerical results.

Inlet↗
NASA NTRSDate not supplied

Computational Aerodynamic Analysis in Support of the CRM Tail Cone Thruster Configuration Wind Tunnel Test

NASA’s Advanced Air Transport Technology (AATT) project is breaching the boundaries of aircraft design in pursuit of eco-friendly solutions that are compatible with urban noise comfort levels. Boundary layer ingesting (BLI) propulsion systems promise to reduce fuel burn with additional potential benefits in noise reduction. Type-II BLI systems of the STARC-ABL type are the subject of a test campaign planned for fiscal year 2022 in the National Transonic Facility (NTF), for which a CRM-based model with a retrofitted tail cone thruster (TCT) has been designed. The present work is a precursor to the NTF test, where the 240 cases planned for the experiment were simulated using the Launch, Ascent and Vehicle Aerodynamics (LAVA)computational framework. Solution sensitivity to angle of attack, engine operating conditions, and the presence of the supporting structure (sting) in the wind tunnel test are analyzed in the extensive dataset. The main flow features contributing to the inlet distortion are identified as the vertical tail wake, wing downwash and fuselage upsweep vortices, with the latter two experiencing the greatest sensitivity to angle of attack. Finally, results from an inlet-guide-vane(IGV) design/integration study are presented. The LAVA team and the turbomachinery design team at NASA’s Ames and Glenn Research Centers are collaborating in an effort to reduce flow distortion upstream of the fan by means of integrating an IGV system into the CRM-TCT model. A significant improvement in flow distortion metrics has been achieved since the initial design iteration. Results employing an actuator zone model with realistic radially-varying thrust profiles to simulate first-order fan effects within LAVA are presented.

AATT↗
NASA NTRSDate not supplied

Preliminary Assessment of a Distributed Electric Propulsion System for the SUSAN Electrofan

The SUSAN Electrofan is a new hybrid electric large regional jet aircraft concept being studied by NASA that leverages advanced propulsion system technologies such as distributed electric propulsion (DEP) and boundary-layer ingestion (BLI) to reduce fuel consumption and emissions. In order to evaluate the individual benefits of these technologies toward the SUSAN Electrofan’s wing-mounted propulsion systems, three configurations are proposed. The first consists of two underwing pylon-mounted podded propulsors and serves as a baseline, while the second features an underwing pylon-mounted DEP concept with 16 ducted fans in a mail-slot nacelle. The third and final configuration mounts the mail-slot nacelle directly onto the pressure side of the wing to also take advantage of BLI. This paper presents preliminary investigations into the design and performance of the first two propulsion system configurations. This begins with an initial propulsor and mail-slot design where the aeropropulsive design space is explored, and adverse effects are addressed through iterative geometry modifications. The propulsion system configurations are then installed onto a wing–body model to account for integration effects and assess the relative aerodynamic and shaft power performance of each concept. Results indicate the potential benefits of DEP, which come from significant reductions in total drag, provided by operation at much lower propulsor fan pressure ratios.

ARMD↗
NASA NTRSDate not supplied

Conceptual Design of the Hybrid-Electric Subsonic Single Aft Engine (SUSAN) Electrofan Transport Aircraft

This paper presents an update to the conceptual design of NASA’s Subsonic Single Aft Engine (SUSAN) Electrofan transport aircraft—a 180 passenger, Mach 0.785 hybrid-electric regional jet with an economy range of 750 nmi and a design range of 2,500 nmi. The concept employs a series hybrid-electric powertrain driven by a fuel-burning aft fuselage propulsor that is connected to Megawatt-class power generators to convert additional mechanical shaft power to electric power. This electric power is used to support wing-mounted electric propulsors. The aft fuselage turbofan leverages boundary layer ingestion (BLI) and is designed to deliver 35% of the total aircraft thrust, while the wing propulsors assume underwing distributed electric propulsion (DEP) arrangements and are responsible for the remaining 65% thrust. Investigated in this work is the fuel burn performance of the SUSAN Electrofan when incorporating new weight and efficiency estimates for the power, battery, and thermal systems. An updated unified engine deck is also included, which accounts for the high effective bypass ratio made possible by the DEP systems and turbofan BLI effects to first order. Multidisciplinary design analysis and optimization (MDAO) is performed through an updated conceptual design environment, and comparisons are made to a Boeing 737 MAX 8-like reference aircraft performing similar missions, as well as a variant resized for 2,500 nmi.

CAS↗
NASA NTRSDate not supplied

Computational Analysis of a Boundary-Layer Ingesting Tailcone Thruster Configuration Within the National Transonic Facility Using the LAVA Solver

Boundary-layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA’s Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) to study the propulsion-airframe integration effects of the Boundary-Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) solver, to validate the applicability of current best-practice Reynolds-averaged Navier Stokes (RANS) models in accurately predicting the relevant flow-physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles-of-attack between –3° and 4°. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions are analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aftbody boundary-layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage.

AATT↗
NASA NTRS2024

Optimal Control Allocation for Distributed Electric Propulsion in a Series/Parallel Partial Hybrid Powertrain

The SUbsonic Single Aft eNgine (SUSAN) Electrofan is a NASA concept jet transport aircraft with a 2040 entry-into-service date. It utilizes electrified aircraft propulsion (EAP) to enable propulsive and aerodynamic benefits to reduce fuel usage, emissions, and cost. The powertrain consists of a single thrust producing, boundary layer-ingesting (BLI) turbofan gas turbine engine (GTE) with generators driving a series/parallel partial hybrid EAP system. The architecture includes 16 underwing contrarotating BLI fans, eight on each side, in a mailslot configuration. The 16 fans run on power extracted from the GTE through four 5 MW motor/generators connected to the Low-Pressure Spool, and a single 1 MW motor/generator on the High-Pressure Spool. The distributed fans can be used by the flight control to augment or replace the rudder function. At top of climb, the power extracted from the GTE for the fans is boosted by batteries. The design provides redundancy, and the capacity for boost means that the fans are designed to be able to provide additional thrust when necessary. These features can be leveraged in case of a fan or generator failure. This paper sets up the optimal control problem of setpoint determination for individual fans in the distributed propulsion system, accounting for electrical string efficiencies, saturations, and failures. The solution minimizes power consumption while maintaining thrust and torque on the airframe for maneuvering. Additionally, thrust that would have been lost due to temporary fan speed or power saturation is optimally redistributed to maintain overall desired thrust and torque on the aircraft. The power extraction range constraints derive from the gas turbine engine design and the small amount of variation allowed for the engine to maintain operability. The problem formulation allows the number and location of fan failures for which the thrust and torque can be maintained to be investigated, which has implications for certification. Simulations of a coordinated turn utilizing the distributed electric propulsion for yaw rate control under different failure scenarios demonstrate the robustness of the powertrain design to failures and help define its limitations.

Distributed Electric Propulsion↗
NASA NTRSDate not supplied

High-Fidelity Aeropropulsive Assessment of Distributed Electric Propulsion and Boundary Layer Ingestion for the SUSAN Electrofan

This paper presents a high-fidelity aeropropulsive assessment of the SUSAN Electrofan’s distributed electric propulsion (DEP) and boundary layer ingestion (BLI) aft fuselage turbofan technologies. This is achieved through the application of computational tools for aerodynamic and aeropropulsive design and analysis based on the Reynolds-averaged Navier-Stokes (RANS) equations. Representative aircraft models are first developed in 3D for the SUSAN Electrofan concept, a non-DEP variant, and a year 2020 technology level reference aircraft based on the Boeing 737-8. These include airframes developed through the application of RANS-based aerodynamic shape optimization, with the objective of drag minimization at cruise while subject to constant lift and zero pitching moment constraints. Wing propulsors are also included and modeled as free-flying ducted fans. These are developed through RANS-based aeropropulsive shape optimization, with the objective of shaft power minimization while subject to constant net thrust and maximum fan face Mach number constraints. An iterative power balance method is then used to trim each of the decoupled aircraft configurations, providing estimates of relative aerodynamic performance, shaft power, and range efficiency. Results also include power on and off analyses, which indicate reduced thrust-induced drag for the SUSAN Electrofan’s DEP and BLI aft fuselage turbofan propulsors when compared to those of the Boeing 737-8-like reference aircraft.

CAS↗
DOE OSTI2026

High-Sensitivity DNA Aptasensors for Detecting Salivary Biomarker S100A7 in Heart Failure

Early detection of heart failure (HF) is vital for improving patient outcomes, lowering hospital readmission rates, and enabling prompt treatment. We present the first high-affinity DNA aptamer for the salivary HF biomarker S100A7 and its application in highly sensitive, noninvasive diagnostic tests. Iterative truncation of the initial 82-nt aptamer (17–82) produced a 43-nt core (17–43) with a binding affinity of 27 nM, which was further enhanced to 5.5 nM through dimerization. Biochemical and mutational studies confirmed that 17–43 adopts a G-quadruplex structure, which is essential for S100A7 recognition and resistance to enzymatic degradation in human saliva. Incorporating 17–43 into sandwich aptamer-ELISA and hybrid aptamer–antibody ELISA assays allowed detection of recombinant S100A7 in human saliva with limits of detection (LOD) of 7.4 ng mL–1 (0.6 nM) and 29 pg/mL (2.2 pM), respectively-outperforming commercial immunoassays in both sensitivity and dynamic range. The hybrid assay maintained its full performance after 2.5 months of room temperature storage. Additionally, a biolayer interferometry (BLI) sensor with 17–43 quantified S100A7 in patient saliva (n = 3), achieving a LOD of 3.2 ng mL–1 (0.3 nM) with a total assay time of less than 20 min. The aptamer’s stability, high specificity, and versatility across biosensing platforms establish it as a promising tool for noninvasive heart failure diagnostics, laying the groundwork for portable aptamer-based biosensors for multiplexed monitoring of HF biomarkers.

DNA aptamer↗
DOE OSTI2025

Design of a shipping fixture for a compact cryomodule hermetic assembly

Two conduction-cooled 915 MHz superconducting radio frequency hermetic assemblies must be safely transported from the Jefferson Lab in Newport News, VA to General Atomics in San Diego, CA for perfor-mance testing in a custom horizontal test cryostat. One hermetic assembly consists of a 2-cell 915 MHz cavity, a coaxial fundamental power coupler, and the warm-to-cold transition beam tubes. The second hermetic assembly consists of a 2-cell 915 MHz cavity only. The assemblies will be transported on a flatbed air-ride trailer over the approximate 4000 km distance. Design requirements included adequate attenuation of 4g vertical axis, 5g beamline axis, and 1.5g lateral axis shock events. The isolation system was designed using helical wire-rope isolators with modal and transient finite element analysis performed in Ansys. Results show shock attenuation of a 10 ms half-sine pulse input to < 1g in the vertical axis, < 1.5g in the beam-line axis, and < 0.5g in the lateral axis for both assem-blies at the specified design loads and all structural stresses are kept below the material yield limits. Addi-tionally, the natural frequencies of both isolation sys-tems adequately attenuate the fundamental modes of the critical structures.

Accelerator Physics↗
NASA NTRS1971

Table for estimating parameters of Weibull distribution

Table yields best linear invariant /BLI/ estimates for log of reliable life under censored life tests, permitting reliability estimations in failure analysis of items with multiple flaws. These BLI estimates have uniformly smaller expected loss than Gauss-Markov best linear unbiased estimates.

Mann, N. R.↗
NASA NTRS1979

Siple station experiments on wave-particle interactions in the magnetosphere

Natural and controlled whistler-mode signals have been used to study nonlinear mechanisms of wave growth and wave-wave interactions (WWI) in the magnetosphere; three general classes of WWI (triggering, suppression, and entrainment) are identified and interpreted in terms of a model based on cyclotron resonance interaction. This model is also used to estimate the wave field intensity associated with different types of WWI. A new type of triggered emission, the band-limited impulse (BLI) is interpreted in terms of the switching of phase-bunched currents. In addition, an experiment to find a threshold for the excitation of the coherent wave instability is discussed, and observed VLF wave-induced transient bursts of X-rays, light and E-region ionization enhancements are considered with regard to a step function wave interacting with all resonant electrons in a given energy range.

Helliwell, R. A.↗