Search NASA⌕ Search

SEARCH · Search NASA

Results for “BOUNDARY LAYER - PLATES, FLAT - LAMINAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Flap Edge Aeroacoustic Measurements and Predictions

An aeroacoustic model test has been conducted to investigate the mechanisms of sound generation on high-lift wing configurations. This paper presents an analysis of flap side-edge noise, which is often the most dominant source. A model of a main element wing section with a half-span flap was tested at low speeds of up to a Mach number of 0.17, corresponding to a wing chord Reynolds number of approximately 1.7 million. Results are presented for flat (or blunt), flanged, and round flap-edge geometries, with and without boundary-layer tripping, deployed at both moderate and high flap angles. The acoustic database is obtained from a Small Aperture Directional Array (SADA) of microphones, which was constructed to electronically steer to different regions of the model and to obtain farfield noise spectra and directivity from these regions. The basic flap-edge aerodynamics is established by static surface pressure data, as well as by Computational Fluid Dynamics (CFD) calculations and simplified edge flow analyses. Distributions of unsteady pressure sensors over the flap allow the noise source regions to be defined and quantified via cross-spectral diagnostics using the SADA output. It is found that shear layer instability and related pressure scatter is the primary noise mechanism. For the flat edge flap, two noise prediction methods based on unsteady-surface-pressure measurements are evaluated and compared to measured noise. One is a new causality spectral approach developed here. The other is a new application of an edge-noise scatter prediction method. The good comparisons for both approaches suggest that much of the physics is captured by the prediction models. Areas of disagreement appear to reveal when the assumed edge noise mechanism does not fully define, the noise production. For the different edge conditions, extensive spectra and directivity are presented. Significantly, for each edge configuration, the spectra for different flow speeds, flap angles, and surface roughness were successfully scaled by utilizing aerodynamic performance and boundary layer scaling method developed herein.

Brooks, Thomas F.↗
NASA NTRS2002

Dynamics of Diffusion Flames in von Karman Swirling Flows Studied

Von Karman swirling flow is generated by the viscous pumping action of a solid disk spinning in a quiescent fluid media. When this spinning disk is ignited in an oxidizing environment, a flat diffusion flame is established adjacent to the disk, embedded in the boundary layer (see the preceding illustration). For this geometry, the conservation equations reduce to a system of ordinary differential equations, enabling researchers to carry out detailed theoretical models to study the effects of varying strain on the dynamics of diffusion flames. Experimentally, the spinning disk burner provides an ideal configuration to precisely control the strain rates over a wide range. Our original motivation at the NASA Glenn Research Center to study these flames arose from a need to understand the flammability characteristics of solid fuels in microgravity where slow, subbuoyant flows can exist, producing very small strain rates. In a recent work (ref. 1), we showed that the flammability boundaries are wider and the minimum oxygen index (below which flames cannot be sustained) is lower for the von Karman flow configuration in comparison to a stagnation-point flow. Adding a small forced convection to the swirling flow pushes the flame into regions of higher strain and, thereby, decreases the range of flammable strain rates. Experiments using downward facing, polymethylmethacrylate (PMMA) disks spinning in air revealed that, close to the extinction boundaries, the flat diffusion flame breaks up into rotating spiral flames (refs. 2 and 3). Remarkably, the dynamics of these spiral flame edges exhibit a number of similarities to spirals observed in biological systems, such as the electric pulses in cardiac muscles and the aggregation of slime-mold amoeba. The tail of the spiral rotates rigidly while the tip executes a compound, meandering motion sometimes observed in Belousov-Zhabotinskii reactions.

Nayagam, Vedha↗
NASA NTRS1992

Heat transfer with very high free-stream turbulence. I - Experimental data. II - Analysis of results

Boundary layer heat transfer with very high freestream turbulence is investigated. The problem is studied experimentally by placing a constant-temperature heat transfer surface at various locations in the margin of a turbulent free jet and measuring both the surface heat transfer rate and the turbulence in the freestream. Freestream turbulent fluctuations 20 to 60 percent relative to the mean velocity augment heat transfer 1.8 to 4 times that which would be predicted locally using accepted correlations for turbulent boundary layers at the same Reynolds number. The correlations of Simonich and Bradshaw (1989), Pedisius et al. (1983), and Blair (1983) each fail to describe the present data. For flows over flat surfaces in air with very high freestream turbulence, greater than 0.2, u-prime determines h. A new heat transfer parameter, St-prime, characterizes turbulent boundary layer heat transfer with freestream turbulence on the domain 0-0.65 to within +/- 15 percent for high Reynolds number flows with uniform thermal boundary conditions.

Maciejewski, P. K.↗
NASA NTRS1983

The effects of supports on the flow behind a body

Two cases in a supersonic flow with a turbulent boundary layer are studied in order to determine the effects of supports on models with a flat base. The first concerns the effect of various obstacles situated upstream of the two dimensional base, at Mach 2. The second relates to a body of revolution passing through the throat of the jet from upstream to downstream. The interference of obstacles simulating supporting masts is examined for the base, both bare and with a sting, at Mach 1.94. Without any support, the drag of a conical-cylindrical body of revolution was measured by means of the ONERA magnetic suspension. The interference of various stings was studied at Mach 2.4 with a laminary boundary layer and with a separated turbulent boundary layer. The mechanism of the interference of a sting, progressively approached axially to the base, was determined.

Rebuffet, P.↗
NASA NTRS1985

High Marangoni number convection in a square cavity

Steady thermocapillary flows in a square cavity are computed using a finite difference procedure. Accurate numerical solutions are obtained for as high a Reynolds number as possible, in order to characterize the nature of strongly convective flows of this general class. Only the case of capillary number going to zero is considered, so that the free surface is assumed flat at the leading order. Surface deflections are computed by domain perturbation. Boundary layer formation at different values of the Prandtl number is observed at large values of the Marangoni number and Re. The numerical results are used to infer the relevant scalings of a consistent boundary layer picture of the flow, valid asymptotically as Re goes to infinity.

Zebib, A.↗
NASA NTRS2003

Study of Unsteady Flows with Concave Wall Effect

This paper presents computational fluid dynamic studies of the inlet turbulence and wall curvature effects on the flow steadiness at near wall surface locations in boundary layer flows. The time-stepping RANS numerical solver of the NASA Glenn-HT RANS code and a one-equation turbulence model, with a uniform inlet turbulence modeling level of the order of 10 percent of molecular viscosity, were used to perform the numerical computations. The approach was first calibrated for its predictabilities of friction factor, velocity, and temperature at near surface locations within a transitional boundary layer over concave wall. The approach was then used to predict the velocity and friction factor variations in a boundary layer recovering from concave curvature. As time iteration proceeded in the computations, the computed friction factors converged to their values from existing experiments. The computed friction factors, velocity, and static temperatures at near wall surface locations oscillated periodically in terms of time iteration steps and physical locations along the span-wise direction. At the upstream stations, the relationship among the normal and tangential velocities showed vortices effects on the velocity variations. Coherent vortices effect on the velocity components broke down at downstream stations. The computations also predicted the vortices effects on the velocity variations within a boundary layer flow developed along a concave wall surface with a downstream recovery flat wall surface. It was concluded that the computational approach might have the potential to analyze the flow steadiness in a turbine blade flow.

Wang, Chi R.↗
DOE OSTI2023

Investigating the physical mechanisms that modify wind plant blockage in stable boundary layers

Abstract. Wind plants slow down the approaching wind, a phenomenon known as blockage. Wind plant blockage undermines turbine performance for front-row turbines and potentially for turbines deeper into the array. We use large-eddy simulations to characterize blockage upstream of a finite-size wind plant in flat terrain for different atmospheric stability conditions and investigate the physical mechanisms modifying the flow upstream of the turbines. To examine the influence of atmospheric stability, we compare simulations of two stably stratified boundary layers using the Weather Research and Forecasting model in large-eddy simulation mode, representing wind turbines using the generalized actuator disk approach. For a wind plant, a faster cooling rate at the surface, which produces stronger stably stratified flow in the boundary layer, amplifies blockage. As a novelty, we investigate the physical mechanisms amplifying blockage by evaluating the different terms in the momentum conservation equation within the turbine rotor layer. The velocity deceleration upstream of a wind plant is caused by an adverse pressure gradient and momentum advection out of the turbine rotor layer. The cumulative deceleration of the flow upstream of the front-row turbines instigates vertical motions. The horizontal flow is diverted vertically, reducing momentum availability in the turbine rotor layer. Although the adverse pressure gradient upstream of the wind plant remains unchanged with atmospheric stability, vertical advection of horizontal momentum is amplified in the more strongly stable boundary layer, mainly by larger shear of the horizontal velocity, thus increasing the blockage effect.

17 WIND ENERGY↗
NASA NTRS1981

Noise transmission and attenuation for business aircraft

This paper describes analytical studies applicable for estimating the effects of noise transmission into light aircraft and commuter type aircraft. The propeller noise and turbulent boundary layer noise are considered. The analytical model described uses modal methods and incorporates flat stiffened panels for flat sided sidewalls and curved stiffened panels for cylindrical enclosures. The numerical results include noise attenuation with add-on treatments and the sensitivity of the transmitted noise to the discrete stiffening of the sidewall panels.

Vaicaitis, R.↗
NASA NTRS1986

Drag reducing outer-layer devices in rough wall turbulent boundary layers

The ability of outer-layer devices to reduce wall shear stress over a substantial streamwise distance in rough-wall turbulent boundary layers has been studied experimentally. The devices examined are a pair of thin flat ribbons placed in tandem as well as those having symmetric airfoil sections. The wall conditions examined are smooth, d- and k-type transverse-groove and sandgrain roughnesses. The wall drag is found to be reduced from the respective normal levels in all rough walls. All k-type rough walls exhibit a similar level of relative wall drag reduction which is also smaller than that in a smooth-wall. The d-type rough walls exhibit a transitional behaviour - the relative wall drag reduction drops from the smooth wall level to that of the k-type roughness with increasing roughness Reynolds number. However, the absolute reductions in the local wall shear stress are similar in both the rough and smooth walls. On the other hand, the relative reductions are lower in the rough walls because of a higher reference drag which is caused by the unique presence of a pressure component on which the devices are not as effective.

Bandyopadhyay, P. R.↗
DOE OSTI2022

Low-Reynolds-number oscillating boundary layers on adiabatic slopes

We investigate the instabilities and transition mechanisms of Boussinesq stratified boundary layers on sloping boundaries when subjected to oscillatory body forcing parallel to the slope. We examine idealized forms of boundary layers on hydraulically smooth abyssal slopes in tranquil mid- to low-latitude regions, where low-wavenumber internal tides gently heave isopycnals up and down adiabatic slopes in the absence of mean flows, high-wavenumber internal tides, shelf breaks, resonant tide–bathymetry interactions (critical slopes) and other phenomena associated with turbulence ‘hot spots’. In non-rotating low-Reynolds-number flow, increased stratification on the downslope phase has a relaminarizing effect, while on the upslope phase we find transition-to-turbulence pathways arise from shear production triggered by gravitational instabilities. When rotation is significant (low slope Burger numbers) we find that boundary layer turbulence is sustained throughout the oscillation period, resembling stratified Stokes–Ekman layer turbulence. Simulation results suggest that oscillating boundary layers on smooth slopes at low Reynolds number ($Re\leqslant 840$), unity Prandtl number and slope Burger numbers greater than unity do not cause significant irreversible turbulent buoyancy flux (mixing), and that flat-bottom dissipation rate models derived from the tide amplitude are accurate within an order of magnitude.

42 ENGINEERING↗
NASA NTRS1984

Experiments suitable for wind tunnel wall interference assessment/correction

Three experiments suitable for wall interference assessment and evaluation of proposed correction methods are presented. The experiments are: (1) a series of airfoil tests using a newly designed transonic flow facility that employs side-wall boundary layer suction and upper- and lower-wall shaping; (2) tests on a swept airfoil section spanning a solid-wall wind tunnel with fixed contouring on all four walls; and (3) tests on a swept wing of aspect ratio 3 mounted in a solid-wall wind tunnel with fixed flat walls. Each of the experiments provides data on the airfoil sections as well as on the wind tunnel walls. All the experiments were performed in solid wall wind tunnels corrected for boundary layer displacement effects. Although the experiments were performed primarily to evaluate computer code performance, it is believed that they also provide information that can be used to evaluate methods for assessing and correcting wall interference effects.

Marvin, J. G.↗
NASA NTRS1981

Experimental data and model for the turbulent boundary layer on a convex, curved surface

Experiments were performed to determine how boundary layer turbulence is affected by strong convex curvature. The data gathered on the behavior of the Reynolds stress suggested the formulation of a simple turbulence model. Data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero. Two experiments were performed at delta/R approximately 0.10, and one at weaker curvature with delta/R approximately 0.05. Results show that after a sudden introduction of curvature the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. When the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions. A simple turbulence model, which was based on the theory that the Prandtl mixing length in the outer layer should scale on the velocity gradient layer, was shown to account for the slow recovery.

Gillis, J. C.↗
NASA NTRS1980

Turbulent boundary layer on a convex, curved surface

The effects of strong convex curvature on boundary layer turbulence were investigated. The data gathered on the behavior of Reynolds stress suggested the formulation of a simple turbulence model. Three sets of data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning, and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero - thus avoiding any effects of streamwise acceleration on the wall layers. Results show that after a sudden introduction of curvature, the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. In contrast, when the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions.

Gillis, J. C.↗
NASA NTRS1992

Convection of tin in a Bridgman system. I - Flow characterization by effective diffusivity measurements

An electrochemical titration method was used to investigate the dynamic states in a cylindrical layer of convecting tin. The liquid tin was contained in a cell, with curved boundaries made of quartz and flat boundaries made of a solid state electrolyte - yttria-stabilized zirconia (YSZ). The electrolyte acted as a window through which a trace amount of oxygen could be pumped in or out by the application of a constant voltage. The concentration at the YSZ interface was monitored by operating the electrochemical cell in the galvanic mode. Experimentally determined effective diffusivities of oxygen were compared with the molecular diffusivity. Dynamic states in the convective flow were thus inferred. Temperature measurements were simultaneously made in order to identify the onset of oscillations from a steady convective regime. The experiments were conducted for two different aspect ratios for various imposed temperature gradients and two different orientations with respect to gravity. Transcritical states were identified and comparison to two-dimensional numerical models were made.

Sears, B.↗
NASA NTRS1994

On the evolution of centrifugal instabilities within curved incompressible mixing layers

It is known that certain configurations which possess curvature are prone to a class of instabilities which their 'flat' counterparts will not support. The main thrust of the study of these centrifugal instabilities has concentrated on curved solid boundaries and their effect on the fluid motion. In this article attention is shifted towards a fluid-fluid interface observed within a curved incompressible mixing layer. Experimental evidence is available to support the conjecture that this situation may be subjected to centrifugal instabilities. The evolution of modes with wavelengths comparable with the layer's thickness is considered and the high Taylor/Gortler number regime is also discussed which characterizes the ultimate fate of the modes.

Otto, S. R.↗
NASA NTRS1991

Relationships between topographic roughness and aeolian processes

The interaction between winds and desert surfaces has important implications for sediment transport on Earth, Mars, and Venus, and for understanding the relationships between radar backscatter and aerodynamic roughness as part of the NASA Shuttle Imaging radar (SIR-C) Mission. Here, researchers report results from measurements of boundary layer wind profiles and surface roughness at sites in Death Valley and discuss their implications. The sites included a flat to undulating gravel and sand reg, alluvial fans, and a playa. Estimates of average particle size composition of Death Valley sites and arithmetic mean values of aerodynamic roughness are given in tabular form.

Greeley, Ronald↗
NASA NTRS1975

Design and preliminary test results at Mach 5 of an axisymmetric slotted sound shield

The basic theory and sound attenuation mechanisms, the design procedures, and preliminary experimental results are presented for a small axisymmetric sound shield for supersonic wind tunnels. The shield consists of an array of small diameter rods aligned nearly parallel to the entrance flow with small gaps between the rods for boundary layer suction. Results show that at the lowest test Reynolds number (based on rod diameter) of 52,000 the noise shield reduced the test section noise by about 60 percent ( or 8 db attenuation) but no attenuation was measured for the higher range of test reynolds numbers from 73,000 to 190,000. These results are below expectations based on data reported elsewhere on a flat sound shield model. The smaller attenuation from the present tests is attributed to insufficient suction at the gaps to prevent feedback of vacuum manifold noise into the shielded test flow and to insufficient suction to prevent transition of the rod boundary layers to turbulent flow at the higher Reynolds numbers. Schlieren photographs of the flow are shown.

Beckwith, I. E.↗
NASA NTRS1982

Sound shield

An improved test section for a supersonic or hypersonic wind tunnel is disclosed wherein the model tested is shielded from the noise normally radiated by the turbulent tunnel wall boundary layer. A vacuum plenum surrounds spaced rod elements making up the test chamber to extract some of the boundary layer as formed along the rod elements during a test to thereby delay the tendency of the rod boundary layers to become turbulent. Novel rod construction involves bending each rod slightly prior to machining the bent area to provide a flat segment on each rod for connection with the flat entrance fairing. Rods and fairing are secured to provide a test chamber incline on the order of 1 deg outward from the noise shield centerline to produce up to 65% reduction of the root mean square (rms) pressure over previously employed wind tunnel test sections at equivalent Reynolds numbers.

Creel, T. R., Jr.↗