Search NASA⌕ Search

SEARCH · Search NASA

Results for “BROMINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Sensitivity of Ozone to Bromine in the Lower Stratosphere

Measurements of BrO suggest that inorganic bromine (Br(sub y)) at and above the tropopause is 4 to 8 ppt greater than assumed in models used in past ozone trend assessment studies. This additional bromine is likely carried to the stratosphere by short-lived biogenic compounds and their decomposition products, including tropospheric BrO. Including this additional bromine in an ozone trend simulation increases the computed ozone depletion over the past approx.25 years, leading to better agreement between measured and modeled ozone trends. This additional Br(sub y) (assumed constant over time) causes more ozone depletion because associated BrO provides a reaction partner for ClO, which increases due to anthropogenic sources. Enhanced Br(sub y) causes photochemical loss of ozone below approx.14 km to change from being controlled by HO(sub x) catalytic cycles (primarily HO2+O3) to a situation where loss by the BrO+HO2 cycle is also important.

ozone trends↗
NASA NTRS1975

The chemistry of atmospheric bromine

Bromine may act as a catalyst for recombination of ozone and could be more efficient than either nitric oxide or chlorine. The lower atmosphere contains small concentrations of gaseous bromine produced in part by marine activity and volatilization of particulate material released during the combustion of leaded gasoline, with an additional contribution due to the use of methyl bromide as an agricultural fumigant. Observations by Lazrus et al., (1975) indicate small concentrations of bromine, about 10 to the -11th power (v/v), in the contemporary stratosphere and appear to imply a reduction of approximately 0.3% in the global budget of O3. Estimates are given for future reductions in O3 which might occur if the use of CH3Br as an agricultural fumigant were to continue to grow at present rates.

Wofsy, S. C.↗
NASA NTRS1982

A new brominated polymeric additive for flame retardant glass-filled polybutylene terephthalate

Attention is called to the undesirable effects (poor ultraviolet light stability and blooming) sometimes introduced by brominated flame retarders. A brominated polymeric additive (BPA) with little or none of these undesirable side effects is compared with decabromobiphenyl oxide (DBBPO). The additive bears the product name F-2300. It is found to be more easily dispersed than DBBPO. The F-2300 is as effective as the DBBPO in the oxygen index test. The improved efficiency of the F-2300 may be explained by its better dispersion in polybutylene terephthalate (PBT). Glass-filled PBT containing F-2300 is found to be more resistant to UV degradation than DBBPO-containing formulas. Formulations with F-2300 therefore have a longer useful outdoor life. F-2300 is a diglycidyl-type polymer containing 50 percent aromatically bound bromine. Its melting point is 112 C, and it is stable up to 372 C. It is pointed out that since its melts at a relatively low temperature, it can be introduced into the formulation as a large agglomerate and still be dispersed evenly throughout the polymer.

Nir, Z.↗
NASA NTRS1983

Polyfunctional epoxies - Different molecular weights of brominated polymeric additives as flame retardants in graphite composites

The imparting of flame retardancy to graphite-reinforced composites without incurring mechanical property deterioration is investigated for the case of an experimental, trifunctional epoxy resin incorporating brominated polymeric additives (BPAs) of the diglycidyl type. Such mechanical properties as flexural strength and modulus, and short beam shear strength, were measured in dry and in hot/wet conditions, and the glass transition temperature, flammability, and water absorption were measured and compared with nonbromilated systems. Another comparison was made with a tetrafunctional epoxy system. The results obtained are explained in terms of differences in the polymeric backbone length of the bromine carrier polymer. BPAs are found to be a reliable bromine source for fire inhibition in carbon-reinforced composites without compromise of mechanical properties.

Nir, Z.↗
NASA NTRS1984

Measurements of stratospheric bromine

From 1974 to 1977, molecules containing acidic bromine were sampled in the stratosphere by using tetrabutyl ammonium hydroxide impregnated filters. Sampling was accomplished by WB-57F aircraft and high-altitude balloons, spanning latitudes from the equator to 75 deg N and altitudes up to 36.6 km. Analytical results are reported for 4 years of measurements and for laboratory simulations that determined the filter collection efficiencies for a number of brominated species. Mass mixing ratios for the collected bromine species in air average about 27 pptm in the stratosphere. Seasonal variability seems to be small.

Sedlacek, W. A.↗
NASA NTRS1985

Rubberized, Brominated Epoxies

Graphite/epoxy composite materials made with resins containing bromine and rubber additives. New composites tougher and more resistant to fire. Flame resistance increased by introducing bromine via commercial brominated flame-retartant polymeric additives.

Gilwee, W.↗
NASA NTRS1986

A comparison of the bromination dynamics of pitch-based and vapor-grown graphite fibers

The electrical resistance of pitch based P-100 fibers and experimental organic vapor grown fibers was recorded in-situ during bromination and subsequent exposure to ambient laboratory air. The results indicate that the bromination and debromination reactions proceed much slower for vapor grown fibers than for pitch based. While this may be due in part to the larger diameter of the vapor grown fibers, the majority of the effect can probably be attributed to the differences in graphene plane orientation between the fiber types. Although the reactions are slower in the vapor grown than in the pitch based fibers, the extent of reaction as measured by the change in electrical resistance is essentially the same, with comparable (or larger) decreases in resistivity. The bromination reaction proceeds with one or more plateaus in the resistance versus time curves, which suggests staging and strengthens the argument that these fibers produce true intercalation compounds.

Gaier, J. R.↗
NASA NTRS1987

Effects of sequential treatment with fluorine and bromine on graphite fibers

Three pitch based graphite fibers with different degrees of graphitization and one polyacryonitrile (PAN) based carbon fiber from Amoco Corporation were treated with 1 atm, room temperature fluorine gas for 90 hrs. Fluorination resulted in higher electrical conductivity for all pitch fibers. Further bromination after ambient condition defluorination resulted in further increases in electrical defluorination conductivity for less graphitized, less structurally ordered pitch fibers (P-55) which contain about 3% fluorine by weight before bromination. This product can be stable in 200 C air, or 100% humidity at 60 C. Due to its low cost, this less graphitized fiber may be useful for industrial application, such as airfoil deicer materials. The same bromination process, however, resulted in conductivity decreases for fluorine rich, more graphitized, structurally oriented pitch fibers (P-100 and P-75). Such decreases in electrical conductivity were partially reversed by heating the fibers at 185 C in air. Differential scanning calorimetric (DSC) data indicated that the more graphitized fibers (P-100) contained BrF3, whereas the less graphitized fibers (P-55) did not.

Hung, Ching-Cheh↗
NASA NTRS1986

Properties and potential applications of brominated P-100 carbon fibers

A review of the properties and potential applications of bromine-intercalated pitch-based carbon fibers is presented. The dynamics of the intercalation reaction are summarized, and characteristics, such as resistivity, density, and stability, are discussed. In addition, the mechanical and electrical properties of bromine-intercalated fiber-epoxy conposites will be addressed. With conductivities comparable to stainless steel, these brominated carbon fibers may be used in a number of composite applications, such as electromagnetic interference shielding containers, large conductive space structures, lightning strike-tolerant aircraft surfaces, and aircraft deicing applications.

Jaworske, D. A.↗
NASA NTRS1987

Mechanical and electrical properties of graphite fiber-epoxy composites made from pristine and bromine intercalated fibers

The mechanical and electrical properties of pristine and bromine intercalated graphite fiber-epoxy composites were compared. The two types of composite were similar in terms of tensile modulus, tensile strength, and Poisson's Ratio. However, the interlaminar shear strength of the brominated composite was 18 percent greater than its pristine counterpart. Only slight differences were observed in flexural properties. A five-fold decrease was observed in the electrical resistivity of the brominated composite parallel to the axis of the fibers, resulting in a unidirectional resistivity of about 90 microOmega/cm. Transverse resistivity was unaffected. Both types of composite were subjected to a simulated lightning strike of 10 KJ (at a peak current of 150 kA), and the composite with the intercalated graphite exhibited less damage.

Jaworske, Donald A.↗
NASA NTRS1987

The effect of bromination of carbon fibers on the coefficient of thermal expansion of graphite fiber-epoxy composites

To examine the effect of bromination of carbon fibers on the coefficient of thermal expansion (CTE) of carbon fiber epoxy composites, several pristine and brominated carbon fiber-epoxy composite samples were subjected to thermomechanical analysis. The CTE's of these samples were measured in the uniaxial and transverse directions. The CTE was dominated by the fibers in the uniaxial direction, while it was dominated by the matrix in the transverse directions. Bromination had no effect on the CTE of any of the composites. In addition, the CTE of fiber tow was measured in the absence of a polymer matrix, using an extension probe. The results from this technique were inconclusive.

Jaworske, D. A.↗
NASA NTRS1987

Improving the interlaminar shear strength of carbon fiber-epoxy composites through carbon fiber bromination

The use of bromine to improve the interlaminar shear strength of PAN-based carbon fibers was investigated. Composite test specimens fabicated from brominated T-300 fibers and a MY720 matrix exhibited on average a 30% improvement in ILSS over their pristine counterparts. Mass, electrical resistivity, density, contact angle, and scanning Auger microscopy results suggested a mechanism in which the bromine was covalently bonded to the surface of the fiber, and this resulted in an increased van der Waal's adhesion between fiber and matrix.

Jaworske, Donald A.↗
NASA NTRS1987

A comparison of the bromination dynamics of various carbon and graphite fibers

The electrical resistance of four grades of pitch-based graphite fibers and three experimental organic vapor-derived fibers was determined in situ during bromination and subsequent exposure to ambient laboratory air. The results show that the least graphitic pitch-based fiber does not brominate significantly, and that bromination and debrominaton reactions proceed much slower for vapor-derived fibers than for pitch-based ones. It is suggested that this decreased reacton rate is primarily due to the differences in graphene plane orientation between the fiber types. The results also imply that the vapor-derived and pitch-based fibers produce true intercalation compounds.

Gaier, James R.↗
NASA NTRS1993

The bromine content of micrometeorites - Arguments for stratospheric contamination

Bromine-salt nanocrystals are associated with a porous chondritic micrometeorite (W7029E5) that was collected in the lower stratosphere. These salt nanocrystals occur together with volcanic Na and K salt nanocrystals embedded in sulfuric acid droplets that were originally adhered to the particle. These materials were concentrated during hexane rinsing as part of routine curation procedures at the NASA Johnson Space Center Cosmic Dust Curatorial Facility. This observation is fortuitous to the extent that the concentration of nanocrystals and sulfuric acid is an experimental artifact of curation. If bromine is a stratospheric contaminant due to surface adsorption, there should be a positive linear relationship between the mass-normalized residence time and bromine content of individual micrometeorites. I show that the predicted correlation exists using a new model to calculate the stratospheric residence time of individual nonspherical micrometeorites in the slow-settling Wilson-Huang regime of the stratosphere.

Rietmeijer, Frans J. M.↗
NASA NTRS2012

Field and Satellite Observations of the Formation and Distribution of Arctic Atmospheric Bromine Above a Rejuvenated Sea Ice Cover

Recent drastic reduction of the older perennial sea ice in the Arctic Ocean has resulted in a vast expansion of younger and saltier seasonal sea ice. This increase in the salinity of the overall ice cover could impact tropospheric chemical processes. Springtime perennial ice extent in 2008 and 2009 broke the half-century record minimum in 2007 by about one million km2. In both years seasonal ice was dominant across the Beaufort Sea extending to the Amundsen Gulf, where significant field and satellite observations of sea ice, temperature, and atmospheric chemicals have been made. Measurements at the site of the Canadian Coast Guard Ship Amundsen ice breaker in the Amundsen Gulf showed events of increased bromine monoxide (BrO), coupled with decreases of ozone (O3) and gaseous elemental mercury (GEM), during cold periods in March 2008. The timing of the main event of BrO, O3, and GEM changes was found to be consistent with BrO observed by satellites over an extensive area around the site. Furthermore, satellite sensors detected a doubling of atmospheric BrO in a vortex associated with a spiral rising air pattern. In spring 2009, excessive and widespread bromine explosions occurred in the same region while the regional air temperature was low and the extent of perennial ice was significantly reduced compared to the case in 2008. Using satellite observations together with a Rising-Air-Parcel model, we discover a topographic control on BrO distribution such that the Alaskan North Slope and the Canadian Shield region were exposed to elevated BrO, whereas the surrounding mountains isolated the Alaskan interior from bromine intrusion.

Nghiem, Son V.↗
DOE OSTI2020

High-Resolution Comonomer Sequencing of Blocky Brominated Syndiotactic Polystyrene Copolymers Using 13C NMR Spectroscopy and Computer Simulations

This work demonstrates the first high-resolution comonomer sequencing of Blocky brominated syndiotactic polystyrene (sPS-co-sPS-Br) copolymers based on pentad assign- ments of the quaternary carbon region of the nuclear magnetic resonance spectrum. Copolymers containing p-bromostyrene (Br-Sty) units were prepared in matched sets using postpolymerization bromination methods carried out in the heterogeneous gel state (Blocky) and homogeneous solution state (Random). Quantitative information from the quaternary carbon spectra, heteronuclear multiple bond correlation spectroscopy, electronic structure calculations, and simulated statistically random copolymers was correlated to confirm the carbon resonance assignments for all 20 possible pentad comonomer sequences. Using the experimental pentad sequence prevalences, a computer code was developed to simulate chains with microstructures typical of each sample as a means to visually represent the copolymer blockiness with quantitative precision. Based on the microstructure and distribution of run lengths in these chains, the simulations revealed that the Blocky copolymers contain a high degree of blockiness. By comparing the run lengths in the simulated chains to the average number of styrene units in a crystalline segment of sPS (found by small-angle X-ray scattering), copolymer crystallizability was predicted. For the simulated Blocky B-21% (21 mol % Br-Sty) chain, the probability of randomly selecting a styrene unit in a crystallizable block was 25.8%, while that in the simulated Random R-18% was zero, in excellent agreement with the experimental crystallization behavior measured by differential scanning calorimetry. Additionally, these predictions confirmed that the simulated chains accurately represent the ensemble of chains in their respective copolymer samples. Furthermore, each simulated Blocky chain contained one or more long sPS blocks that paralleled the measured 38-40 styrene units spanning a crystalline segment within the sPS/CCl4 gel. This finding affirmed that the long sPS segments originated from the precise lamellar structure within the heterogeneous gel morphology (i.e., block length is correlated with lamellar thickness). Overall, the ability to tailor the copolymer microstructure through control of the semicrystalline gel morphology opens the door to synthesizing ordered copolymers by postpolymerization functionalization processes with unprecedented levels of compositional control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Absolute photoionization cross sections of brominated organics and determination of an effective C—Br bond cross section

For this work, absolute photoionization cross sections for five brominated species were measured using multiplexed synchrotron photoionization mass spectrometry at the Advanced Light Source (Lawrence Berkeley National Laboratory). These data enable reliable detection of bromine-containing compounds and estimation of C—Br bond photoionization cross sections. Complementary electronic-structure calculations provided adiabatic ionization energies in good agreement with experiment, while thermochemical appearance energies were measured directly. Bond dissociation energies for key fragmentation pathways of the neutral parent molecules were also analyzed. At 11 eV, cross sections were 53.8 ± 7.50 Mb (sp 2 C—Br) and 48.8 ± 7.70 Mb (sp 3 C—Br).

Brominated compounds↗
DOE OSTI2022

A chiral alkali metal capped Ni 4 cubane complex: Synthesis, structure, magnetic and catalytic bromination studies

A new chiral NaO 2 Ni 4 O 2 N 2 cluster has been developed with a distorted capped cubane-type structure. The structure was determined by single crystal X-ray diffraction. The tetradentate Schiff-base ligand was synthesized by the condensation of o-vanillin and $\textit{D}$-(-)–threo-2-amino-1-(4-nitrophenyl)-1,3-propanediol. X-ray structure reveals that the complex possesses a Ni 4 cubane cluster where sodium ion is anchored on the face of the cubane structure. Continuous shape measurement studies revealed that all the Ni centres are in distorted octahedral geometry and sodium ion adopts the spherical square pyramidal geometry. Further structural exploration reveals that the complex shows local distortions of the coordination geometries at each metal site, and these distortions govern the magnetic anisotropy associated with each Ni II ion. For the present case, an elongation ($d_{str}$ > 0) of the octahedral coordination sphere results in a local easy-plane anisotropy, with a positive $D_{Ni(II)}$ parameter. Temperature dependant magnetization measurements showed a predominant ferromagnetic interaction amongst the four Ni centres. This complex is also catalytically active towards bromination of aromatic phenolic compounds. Initial catalytic activity was verified with the conversion of phenol red to bromophenol blue. Different phenolic substances show good conversion to their corresponding bromo derivatives. The complex showed good catalytic activity towards bromination of aromatic phenolic compounds, offering up to 99% conversion with 100% selectively to their corresponding bromo derivatives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗