Sonic boom effects on beams loosely bound to their supports.
Potential damage to structural elements caused by sonic booms determined by considering effect of gap between beam and supports
Benveniste, J. E.↗
SEARCH · Search NASA
Results for “Beam damage”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Early experience with a highly mobile Lageos ranging system
Two portions of the University of Texas Transportable Laser Ranging System (TLRS) are presented: the beam director and the burst mode single photon laser ranging system. The system, optimized for the Lageos target, has satellite track rates varying from approximately 1800 arcsec per sec on low targets to a few arcsec per sec on the highest. Using full aperture, approximately 3 millijoules of laser power per shot can be transmitted without exceeding the eye damage threshold, and a beam divergence of less than 30 arcsec is dictated by these parameters. Position loop response is optimized, and the instrument is capable of tracking the satellite from nearly any firm, flat position. The laser ranging system uses a multiple pulse laser, and power restrictions result in an average return of less than one photoelectron per shot. The use of a simple laser for ranging has virtually eliminated the high percentage of down time.
Silverberg, E. C.↗
The effects of ion gun beam voltage on the electrical characteristics of NbCN/PbBi edge junctions
The authors have succeeded in fabricating high-quality submicron NbCN edge junctions using a technique which is commonly used to make Nb edge junctions. A modified commercial ion gun was used to cut an edge in SiO2/NbCN films partially covered with photoresist. An insulating barrier was then formed on the exposed edge by reactive ion beam oxidation, and a counterelectrode of PbBi was deposited. The electrical quality of the resulting junctions was found to be strongly influenced by the ion beam acceleration voltages used to cut the edge and to oxidize it. For low ion beam voltages, the junction quality parameter was as high as Vm = 55 mV (measured at 3 mV), but higher ion beam voltages yielded strikingly poorer quality junctions. In light of the small coherence length of NbN, the dependence of the electrical characteristics on ion beam voltage is presumably due to mechanical damage of the NbCN surface. In contrast, for similar ion beam voltages, no such dependence was found for Nb edge junctions.
Lichtenberger, A. W.↗
Fe and O EELS Studies of Ion Irradiated Murchison CM2 Carbonaceous Chondrite Matrix
Introduction: The physical and chemical response of hydrated carbonaceous chondrite materials to space weathering processes is poorly understood. Improving this understanding is a key part of establishing how regoliths on primitive carbonaceous asteroids respond to space weathering processes, knowledge that supports future sample return missions (Hayabusa 2 and OSIRISREx) that are targeting objects of this type. We previously reported on He+ irradiation of Murchison matrix and showed that the irradiation resulted in amorphization of the matrix phyllosilicates, loss of OH, and surface vesiculation. Here, we report electron energy-loss spectroscopy (EELS) measurements of the irradiated material with emphasis on the Fe and O speciation. Sample and Methods: A polished thin section of the Murchison CM2 carbonaceous chondrite was irradiated with 4 kilovolts He(+) (normal incidence) to a total dose of 1 x 10(exp 18) He(+) per square centimeter. We extracted thin sections from both irradiated and unirradiated regions in matrix using focused ion beam (FIB) techniques with electron beam deposition for the protective carbon strap to minimize surface damage artifacts from the FIB milling. The FIB sections were analyzed using a JEOL 2500SE scanning and transmission electron microscope (STEM) equipped with a Gatan Tridiem imaging filter. EELS spectra were collected from 50 nanometer diameter regions with an energy resolution of 0.7 electronvolts FWHM at the zero loss. EELS spectra were collected at low electron doses to minimize possible artifacts from electron-beam irradiation damage. Results and Discussion: Fe L (sub 2,3) EELS spectra from matrix phyllosilicates in CM chondrites show mixed Fe(2+)/Fe(3+) oxidation states with Fe(3+)/Sigma Fe approximately 0.5. Fe L(sub 2,3) spectra from the irradiated/ amorphized matrix phyllosilicates show higher Fe(2+)/Fe(3+) ratios compared to spectra obtained from pristine material at depths beyond the implantation/amorphization layer. We also obtained O Ka spectra from phyllosilicates in both regions of the sample. The O Ka spectra show a pre-edge feature at approximately 530.5 electronvolts that is related to O 2p states hybridized with Fe 3d states. The intensity ratio of the O Ka pre-edge peak relative to the main part of the O Ka edge (that results from transitions of O 1s to 2p states) is lower in the irradiated layer compared to the pristine material and may reflect the loss of O (as OH) as was observed by IR spectroscopy. Conclusions: In addition to amorphization and OH loss, EELS spectra of He(+) irradiated matrix phyllosilicates in Murchison show that some of the Fe(3+) is reduced to Fe(2+). Spectral deconvolution is underway to extract quantitative ratios from the EELS spectra.
Keller, L. P.↗
Characterization of electrical discharges on Teflon dielectrics used as spacecraft thermal control
The dual effects of system degradation and reduced life of synchronous-orbit satellites as a result of differential spacecraft charging underscore the need for a clearer understanding of the prevailing electrical discharge phenomena. In a laboratory simulation, the electrical discharge current, surface voltage, emitted particle fluxes, and photo-emission associated with discharge events on electron beam irradiated silver-backed Teflon samples were measured. Sample surface damage was examined with optical and electron beam microscopes. The results are suggestive of a model in which the entire sample surface is discharged by lateral sub-surface currents flowing from a charge deposition layer through a localized discharge channel to the back surface of the sample. The associated return current pulse appears to have a duration which may be a signature by which different discharge processes may be characterized.
Yadlowsky, E. J.↗
Lamb Wave Assessment of Fatigue and Thermal Damage in Composites
Among the various techniques available, ultrasonic Lamb waves offer a convenient method of evaluating composite materials. Since the Lamb wave velocity depends on the elastic properties of a structure, an effective tool exists to monitor damage in composites by measuring the velocity of these waves. Lamb wave measurements can propagate over long distances and are sensitive to the desired in-plane elastic properties of the material. This paper describes two studies which monitor fatigue damage and two studies which monitor thermal damage in composites using Lamb waves. In the fatigue studies, the Lamb wave velocity is compared to modulus measurements obtained using strain gage measurements in the first experiment and the velocity is monitored along with the crack density in the second. In the thermal damage studies, one examines samples which were exposed to varying temperatures for a three minute duration and the second includes rapid thermal damage in composites by intense laser beams. In all studies, the Lamb wave velocity is demonstrated to be an excellent method to monitor damage in composites.
Seale, Michael D.↗
Long-term hygrothermal effects on damage tolerance of hybrid composite sandwich panels
A sandwich construction, composed of hybrid carbon-glass fiber-reinforced plastic skins and a syntactic foam core, was selected as the design concept for a wind tunnel compressor blade application, where high damage tolerance and durability are of major importance. Beam specimens were prepared from open-edge and encapsulated sandwich panels which had previously been immersed in water at different temperatures for periods of up to about two years in the extreme case. Moisture absorption and strength characteristics, as related to time of exposure to hygrothermal conditions, were evaluated for the sandwich specimens and their constituents (skins and foam). After different exposure periods, low-velocity impact damage was inflicted on most sandwich specimens and damage characteristics were related to impact energy. Eventually, the residual compressive strengths of the damaged (and undamaged) beams were determined flexurally. Test results show that exposure to hygrothermal conditions leads to significant strength reductions for foam specimens and open-edge sandwich panels, compared with reference specimens stored at room temperature. In the case of skin specimens and for beams prepared from encapsulated sanwich panels that had previously been exposed to hygrothermal conditions, moisture absorption was found to improve strength as related to the reference case. The beneficial effect of moisture on skin performance was, however, limited to moisture contents below 1% (at 50 C and lower temperatures). Above this moisture level and at higher temperatures, strength degradation of the skin seems to prevail.
Ishai, Ori↗
Simulating the Clamped Tapered Beam Specimen Under Quasi-Static and Fatigue Loading Using Floating Node Method
As part of the NASA Advanced Composites Project (ACP), a sub-element has been designed to provide validation data for progressive damage analysis models. The clamped tapered beam is a cross-ply laminated composite specimen designed to validate the simulation of the onset of matrix cracks and their interaction with delaminations, including delamination migration. A tapered geometry was used to localize the first damage occurrence in the tapered region, without prescribing an initial crack. The boundary and loading conditions were chosen to favor delamination growth and subsequent migration after the first damage occurrence. The typical sequence of events consists of a matrix crack located at the tapered region, leading to delamination onset, followed by delamination growth and subsequent delamination migration to a different interface via a dominant matrix crack. The Clamped Tapered Beam (CTB) was tested in both quasi-static and fatigue regimes. The results obtained are used in this study to assess and validate a methodology based on the Floating Node Method (FNM) implemented as an Extended Interface Element. In this methodology, quasi-static and fatigue damage formation and development are modeled by combining FNM to represent crack networks, with Directional Cohesive Zone Elements (DCZE) and Virtual Crack Closure Technique (VCCT), respectively. Qualitatively, the methodology is capable of predicting the sequence of events and overall failure morphology. Quantitatively, the simulation results generally bound the experimental data, based on the range of the characterization data used. In this paper, the results from quasi static and fatigue simulations are compared and correlated with experimental data.
Seshadri, B. R.↗
Acoustic Emission Analysis of Damage Progression in Thermal Barrier Coatings Under Thermal Cyclic Conditions
Damage evolution of electron beam-physical vapor deposited (EBVD-PVD) ZrO2-7 wt.% Y2O3 thermal barrier coatings (TBCs) under thermal cyclic conditions was monitored using an acoustic emission (AE) technique. The coatings were heated using a laser heat flux technique that yields a high reproducibility in thermal loading. Along with AE, real-time thermal conductivity measurements were also taken using infrared thermography. Tests were performed on samples with induced stress concentrations, as well as calcium-magnesium-alumino-silicate (CMAS) exposure, for comparison of damage mechanisms and AE response to the baseline (as-produced) coating. Analysis of acoustic waveforms was used to investigate damage development by comparing when events occurred, AE event frequency, energy content and location. The test results have shown that AE accumulation correlates well with thermal conductivity changes and that AE waveform analysis could be a valuable tool for monitoring coating degradation and provide insight on specific damage mechanisms.
calcium-magnesium-alumino-silicate (CMAS)↗
Investigating the Role of Incident Ion Flux in Solar Wind Space Weathering of Carbon-Rich Asteroidal Regolith Via H+ and He+ Irradiation of the Murchison Meteorite
We present results from a set of low and high flux 1 keV/amu H + and He + irradiation experiments performed on slabs of the Murchison CM2 carbonaceous chondrite. The low flux conditions for H + and He + irradiation were ~1-1.5 orders of magnitude lower than the high flux conditions, and each experiment was irradiated to a total fluence between ~3 × 10 16 to ~6 × 10 16 ions/cm 2 . Irradiation-induced changes in the surface chemistry and optical properties of the Murchison samples were evaluated using in situ X-ray photoelectron spectroscopy (XPS) and visible and near-infrared spectroscopy (VNIR). We characterized the microstructure and composition of ion damaged rims in focused ion beam (FIB) cross-sections extracted from olivine and matrix material in each irradiated Murchison slab using transmission electron microscopy (TEM). XPS results suggest that both low flux and high flux H + and He + irradiation cause minor sputtering of surface carbon as well as a reduction in the valence state of iron, from Fe 3+ to Fe 2+ . Slope bluing is observed in VNIR spectra of the irradiated samples which may reflect carbonization and dehydrogenation of organic species and contrasts with reddening trends associated with npFe 0 formation. Although we do not observe a strong flux-dependence on the crystallinity of ion-damaged olivine, TEM analyses reveal a variety of microstructures in all olivine FIB-sections, suggesting that crystallographic orientation affects amorphization efficiency. Analyses of matrix FIB-sections indicate that phyllosilicate alteration is mainly driven by He+ irradiation, where the higher incident flux leads to greater amorphization and the formation of more distinct ion-damaged layers, similar to smooth layers in returned Ryugu particles. TEM results also provide some evidence that higher ion flux leads to greater vesiculation, with He + irradiation being more efficient at vesiculation than H + irradiation, and that higher ion flux may promote the segregation of Mg and Si into laterally extensive lenses and layers in olivine samples. We discuss the implications of these findings for constraining the role that ion flux plays in the development of space weathering characteristics in silicate phases present in carbonaceous asteroidal regoliths. These results will be important for understanding the complexity of this process and how it operates on carbon-rich airless bodies like asteroids Bennu and Ryugu.
meteorites↗
Sensitivity analysis of the optimal solution obtained from the structural damage indentification process
An identification procedure proposed by Shen and Taylor to determine the crack characteristics (location and size of the crack) from dynamic measurements is tested. This procedure was based on minimization of either the 'mean-square' measure of difference between measurement data (natural frequencies and mode shapes) and the corresponding predictions obtained from the computational model. The procedure is tested for simulated damage in the form of symmetric cracks in a simply-supported Bernoulli-Euler beam. The sensitivity of the solution of damage identification problems to the values of parameters that characterize damage is discussed. A sensitivity formula is derived.
Shen, Mo-How H.↗
A model for predicting damage dependent damping in laminated composites
A constitutive model has been developed for predicting the dynamic properties of composite beams which accounts for the influence of microstructural damage. The model assumes the damage state to be fixed. The model can account for both the damping increase and stiffness loss due to microstructural damage. Damage dependent material constants obtained from a baseline data set can be used to predict damping changes for several composite layups. The validity of the model has been verified by comparing the experimental results to model predictions for crossply laminates with a variety of stacking sequences.
Kalyanasundaram, S.↗
Applications of cryogenics in electron microscopy
Description of research and development efforts which resulted in a high-voltage cryoelectron microscope system capable of consistent operation at 1.8 to 4.2 K. Attention is given to the design and operation of superconducting objective lenses providing enhanced resolution during longer exposure times at lower beam intensities (thus reducing radiation damage of specimens). A specific system described combines a closed-cycle superfluid helium refrigerator integrated with a modified 200 kV electron microscope. Consistent resolutions of 8 to 16 A are attained with significantly reduced radiation damage, contamination, and thermal noise in prolonged vibration-free examination of specimens at temperatures from 1.8 to 4.2 K. Applications in specific disciplines are discussed, including membrane ultrastructure, cryobiology, microelectronics, and general superconductivity research.
Fernandez-Moran, H.↗
Alkali mobility in shocked basalt
An electron microprobe was used to study plagioclase in unshocked and experimentally shocked samples of Vacaville basalt, and unstable microprobe analyses have been reported for shocked chondritic meteorites. It is concluded that there is no selective sodium loss due to the shock process. Sodium mobilization under the electron beam reflects increasingly severe lattice damage for increasing shock pressures
Jeanloz, R.↗
Radiation sensitivity of quartz crystal oscillators experiment for the Long Duration Exposure Facility (LDEF)
Factors determining the radiation sensitivity of quartz crystal oscillators were studied on NASA's LDEF. Quartz materials were examined in the transmission electron microscope (TEM) and classified as to their sensitivity to radiation damage by establishing the rate of damage caused by the electron beam in the microscope. Two types of materials, i.e., swept premium Q quartz and natural quartz were chosen because clear differences were observed in their response to the electron beam in the TEM studies. Quartz resonators were then fabricated from them, tested for frequency stability over a greater than 6 mo. period and flown on the LDEF satellite. After retrieval (more than 7 yrs in space) the stability of the resonators was again determined. All of the space exposed resonators fabricated with swept premium Q material exhibited a frequency shift above that of the control resonators: none of the resonators fabricated from the natural quartz materials exhibited such a shift. The significant differences observed between the two types of materials in both the ground-based TEM studies and the space radiation induced frequency changes suggest that there may be a correlation between the two observations.
Ahearn, J. S.↗
A study of the damage tolerance enhancement of carbon/epoxy laminates by utilizing an outer lamina of ultra high molecular weight polyethylene
The damage tolerance of carbon/epoxy was examined when an outer layer of ultra high molecular weight polyethylene (Spectra) material was utilized on the specimen. Four types of 16 ply quasi-isotropic panels, (0,+45,90,-45)s2 were tested. The first contained no Spectra, while the others had one lamina of Spectra placed on either the top (impacted side), bottom or both surfaces of the composite plate. A range of impact energies up to approximately 8.5 Joules (6.3 ft-lbs) was used to inflict damage upon these specimens. Glass/Phenolic honeycomb beams with a core density of 314 N/m3 (2.0 lb/ft3) and 8 ply quasi-isotropic facesheets were also tested for compression-after-impact strength with and without Spectra at impact energies of 1,2,3 and 4 Joules (.74, 1.47, 2.21 and 2.95 ft-lbs). It was observed that the composite plates had little change in damage tolerance due to the Spectra, while the honeycomb panels demonstrated a slight increase in damage tolerance when Spectra was added, the damage tolerance level being more improved at higher impact energies.
Nettles, Alan T.↗
On the enhancement of impact damage tolerance of composite laminates
This paper examines the use of a thin layer of Ultra High Molecular Weight Polyethylene (UHMWPE) on the outer surface of carbon/epoxy composite materials as a method of improving impact resistance and damage tolerance through hybridization. Flat 16-ply laminates as well as honeycomb sandwich structures with eight-ply facesheets were tested in this study. Instrumented drop-weight impact testing was used to inflict damage upon the specimens. Evaluation of damage resistance included instrumented impact data, visual examination, C-scanning and compression after impact (CAI) testing. The results show that only one lamina of UHMWPE did not improve the damage tolerance (strength retention) of the 16-ply flat laminate specimens or the honeycomb sandwich beams, however, a modest gain in impact resistance (detectable damage) was found for the honeycomb sandwich specimens that contained an outer layer of UHMWPE.
Nettles, A. T.↗
Optimization of vibration testing time Technical summary report, 29 Jun. 1964 - 10 Oct. 1965
Optimization of vibration testing time - prediction of equivalent fatigue damage in damped aluminum alloy cantilever beams using Palmgren-Miner and Corten-Dolan hypothesis
VIBRATION TESTING↗