SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Spin-lattice Hamiltonian for trivalent positive Nd and U ions in sites of tetragonal symmetry in calcium fluoride measured with electron spin resonance
Germination of Dryopteris spores is mediated by the physiologically active, far-red-absorbing form of phytochrome, Pfr, and external Ca2+ is necessary for the transduction of the light signal. Because knowledge about the cytoplasmic calcium ion concentration, [Ca2+]i, is of great importance for understanding the role of calcium during signal transduction, this value was measured using fura-2 in fern spores undergoing the normal developmental progression into germination. Fura-2 was loaded into the spores by electroporation, which does not disrupt the normal process of germination. The intensity of the fluorescence emission of the loaded fura-2 was analysed by a microspectrophotometric assay of single spores, and successful loading could be obtained by the application of ten electrical pulses (field strength 7.5 kV cm-1, half-life (time constant) 230 microseconds). Fura-2 was alternately excited by light of wavelengths 355 and 385 nm through an inverted fluorescence microscope, and the emitted fura-2 fluorescence was collected by a silicon-intensified video camera. The cytoplasmic calcium ion concentration was calculated from the ratio of the camera output obtained for both wavelengths and displayed by a pseudo-color technique. Spores responded to changes of the extracellular Ca2+ concentration, and this observation is considered as evidence that fura-2 is loaded into the cytoplasm. The substitution of a low external [Ca2+] (1 mM ethyleneglycol-bis(2-aminoethylether)-N,N,N',N'-tetraacetic acid (EGTA)) by 1 mM CaCl2 caused a fast increase of [Ca2+]i from approx. 50 nM to above 500 nM. In contrast, the subsequent substitution of CaCl2 by EGTA decreased [Ca2+]i again below 100 nM within 0.5 h. Furthermore, the application of ionomycin could initiate a change in [Ca2+]i according to the Ca2+ gradient established between the extracellular medium and cytoplasm. In spores sown on a Ca(2+) -free medium, [Ca2+]i, analysed in a buffer containing EGTA, was found to be around 50 nM during the first days of cultivation, independent of the irradiation protocol. However, if spores were grown in darkness on a Ca(2+) -containing medium and analysed in EGTA, [Ca2+]i was significantly higher (> or = 500 nM). In red-light-irradiated spores, [Ca2+]i was found to decrease with increasing time after irradiation, and was determined to be less than 100 nM when analysis was done 44 h after germination was initiated by the light treatment.
The binding of radiolabeled monoclonal antifibrin antibody 59D8 (specific for fibrin but not fibrinogen) to a series of degraded fibrin clots showed that the availability of the B beta(15-21) epitope (against which 59D8 had been raised) was inversely proportional to the extent of clot lysis. Examination of digest supernatants revealed that the B beta(15-21) epitope was released from clots as a high molecular weight degradation product in the presence of calcium ions but that the generation of low molecular weight peptides occurred in the absence of calcium ions. To address the question of epitope accessibility, we compared levels of fibrin clot binding among four radioactively labeled antibodies: antifibrin monoclonal antibody 59D8, two antifibrinogen monoclonal antibodies that cross-reacted with fibrin, and an affinity-purified polyclonal antifibrinogen antibody. We expected that the antifibrinogen antibodies would show enhanced binding to clots in comparison with the antifibrin antibody. However, the epitope accessibility experiments showed that all four antibody preparations bound fibrin clots at comparable levels. Taken together, these studies demonstrated that one fibrin-specific epitope, B beta(15-21), remains available on clots as they undergo degradation by plasmin and, importantly, that the epitope is not solubilized at a rate faster than the rate at which the clot is itself solubilized. The availability of the B beta(15-21) epitope during the course of plasminolysis assures the potential utility of antifibrin antibodies such as 59D8 for detecting thrombi and targeting plasminogen activators.
Calcium-ion batteries (CIBs) are a promising next-generation energy storage system given the low redox potential of calcium metal and high abundance of calcium compounds. For continued CIB development, the discovery of high energy density calcium ion cathodes is needed to achieve practical energy density values. Here, we report on the use of elemental Se as a promising candidate for a high-capacity cathode material for CIBs that operates via a conversion mechanism in a Ca metal battery at room temperature. The Se electrodes demonstrate a reversible specific capacity of 180 mA h g –1 with a discharge plateau near 2.0 V (vs Ca 2+ /Ca) at 100 mA g –1 using an electrolyte based on the salt calcium tetrakis(hexafluoroisopropyloxy)borate (Ca(B(hfip) 4 ) 2 ) in 1,2-dimethoxyethane (DME) and Ca metal. The reversible electrochemical reaction between calcium and selenium is investigated using operando synchrotron-based techniques and the possible reaction mechanism discussed.
A mathematical model is presented for the transport and precipitation of mineral in refilling osteons. One goal of this model was to explain calcification 'halos,' in which the bone near the haversian canal is more highly mineralized than the more peripheral lamellae, which have been mineralizing longer. It was assumed that the precipitation rate of mineral is proportional to the difference between the local concentration of calcium ions and an equilibrium concentration and that the transport of ions is by either diffusion or some other concentration gradient-dependent process. Transport of ions was assumed to be slowed by the accumulation of mineral in the matrix along the transport path. The model also mimics bone apposition, slowing of apposition during refilling, and mineralization lag time. It was found that simple diffusion cannot account for the transport of calcium ions into mineralizing bone, because the diffusion coefficient is two orders of magnitude too low. If a more rapid concentration gradient-driven means of transport exists, the model demonstrates that osteonal geometry and variable rate of refilling work together to produce calcification halos, as well as the primary and secondary calcification effect reported in the literature.
A mathematical model is presented for the transport and precipitation of mineral in refilling osteons. One goal of this model was to explain calcification 'halos,' in which the bone near the haversian canal is more highly mineralized than the more peripheral lamellae, which have been mineralizing longer. It was assumed that the precipitation rate of mineral is proportional to the difference between the local concentration of calcium ions and an equilibrium concentration and that the transport of ions is by either diffusion or some other concentration gradient-dependent process. Transport of ions was assumed to be slowed by the accumulation of mineral in the matrix along the transport path. ne model also mimics bone apposition, slowing of apposition during refilling, and mineralization lag time. It was found that simple diffusion cannot account for the transport of calcium ions into mineralizing bone, because the diffusion coefficient is two orders of magnitude too low. If a more rapid concentration gradient-driven means of transport exists, the model demonstrates that osteonal geometry and variable rate of refilling work together to produce calcification halos, as well as the primary and secondary calcification effect reported in the literature.
Silicic acid can change into various species such as deposit, colloidal, and soluble form under certain conditions: for example, gradual pH changes around geological disposal repositories. In particular, silicic acid deposits narrow groundwater flow paths, thereby restricting the flow of groundwater. Such effects may contribute to a delay in radionuclide migration. Previous studies have reported that silicic acid supersaturated in sodium and calcium ions can narrow the flow paths. This study examined the effect of magnesium (Mg) and aluminum (Al) ions on the deposition of supersaturated silicic acid on the solid phase. The deposition behavior of supersaturated silicic acid on the solid phase was investigated in a batch system while changing the initial supersaturation concentration, the coexisting ion concentration, and the amount of added solid phase. In the presence of Mg ions, silicic acid precipitation increased with increasing Mg ion concentration due to the influence of the electrolyte, and crosslinking reactions. The coexistence of Al ions significantly suppressed silicic acid deposition due to the formation of a covering on the solid surface during Al ion hydrolysis under conditions of high Al concentration (1.4 mM). On the basis of these experimental results, the apparent deposition rate constant of silicic acid was estimated to be in the range from 10{sup -11} to 10{sup -10} m/s. The Damkoehler number (the dimensionless number expressed by the ratio of the characteristic time of mass transfer and the chemical reaction constant) was sufficient to cause the clogging of the host rock by deposition. This suggests that supersaturated silicic acid deposition, regardless of the presence of Mg ions (and Al ions), contributes to improving barrier performance against radionuclide migration in the host rock. (authors)
Abstract The ever-increasing energy density needs for the mass deployment of electric vehicles bring challenges to batteries. Graphitic carbon must be replaced with a higher-capacity material for any significant advancement in the energy storage capability. Sn-based materials are strong candidates as the anode for the next-generation lithium-ion batteries due to their higher volumetric capacity and relatively low working potential. However, the volume change of Sn upon the Li insertion and extraction process results in a rapid deterioration in the capacity on cycling. Substantial effort has been made in the development of Sn-based materials. A SnCo alloy has been used, but is not economically viable. To minimize the use of Co, a series of Sn–Fe–C, Sn y Fe, Sn–C composites with excellent capacity retention and rate capability has been investigated. They show the proof of principle that alloys can achieve Coulombic efficiency of over 99.95% after the first few cycles. However, the initial Coulombic efficiency needs improvement. The development and application of tin-based materials in LIBs also provide useful guidelines for sodium-ion batteries, potassium-ion batteries, magnesium-ion batteries and calcium-ion batteries. Graphic Abstract
Achieving chemical accuracy for molecular simulations remains a central challenge in computational chemistry. Here, we present an embedded correlated wavefunction transfer learning (ECW-TL) framework for accurately simulating molecular dynamics in the condensed phase. ECW-TL incorporates high-level electron exchange and correlation effects in ECW theory while preserving the training and computational efficiency of machine-learned interatomic potentials. We demonstrate the framework on Ca 2+ –CO 3 2– ion pairing in aqueous solution, a key process underlying CO 2 mineralization in seawater. As proof of principle, we first show that fine-tuning a DFT-revPBE-D3(BJ) baseline model with embedded-DFT-SCAN data reproduces the DFT-SCAN free-energy surface within 1 kcal/mol across all solvation states. Extending the framework to embedded MP2 and localized natural-orbital CCSD(T) further refines the free-energy profile, revealing the crucial role of exact electron exchange and correlation in determining ion-pair stability and structure. The computed ion-pair association free energy is in quantitative agreement with experimental measurements, further validating the accuracy of the ECW-TL framework. ECW-TL thus provides a general, data-efficient route for transferring CW accuracy to efficient simulations of complex aqueous and interfacial chemical processes.
Here, this study aims to investigate the influence of zwitterionic amphiphilic copolymers (ZACs) in the nucleation and growth of heterogeneous CaSO4 at the zwitterion-water interface, which is crucial for the prevention of mineral scaling and consequent downtime or suboptimal performance in industries like membrane desalination, heat exchangers, and pipeline transportation. In situ grazing incidence small angle X-ray Scattering (GISAXS), and quartz crystal microbalance with dissipation (QCM-D) techniques were used to analyze the evolution of CaSO 4 particles on two new ZAC coatings: poly-(trifluoroethyl methacrylate-random-sulfobetaine methacrylate) (PTFEMA-r-SBMA, or PT:SBMA) and poly(trifluoroethyl methacrylate-random-2-methacryloyloxyethyl phosphorylcholine) (PTFEMA-r-MPC, or PT:MPC). The results showed that PT:MPC coatings promoted nucleation but inhibited crystal growth, resulting in slower overall reaction kinetics on PT:MPC coatings compared to PT:SBMA coatings. Interfacial interactions involving the substrates, sulfate minerals, and ions were examined, revealing that calcium ion adsorption, primarily governed by electrostatic attraction, played a crucial role in the nucleation and growth processes on both ZAC coatings. The crystal characterization revealed a phase transition from bassanite to gypsum on both ZAC coatings, suggesting that these zwitterionic materials can influence the mineral phase of heterogeneously formed CaSO 4 crystals. These findings enhance our understanding of the fundamental mechanisms underlying heterogeneous CaSO 4 scaling in the presence of zwitterionic materials.
The ion separation factors for 21 common metal ions with cross-linked polyacrylic acid were determined as a function of pH and the percent of the cross-linked polyacrylic acid neutralized. The calcium ion was used as a reference. At a pH of 5 the decreasing order of affinity of the ions for the cross-linked polyacrylic acid was found to be: Hg++, Fe+++, Pb++, Cr+++, Cu++, Cd++, Al+++, Ag+, Zn++, Ni++, Mn++, Co++, Ca++, Sr++, Ba++, Mg++, K+, Rb+, Cs+, Na+, and Li+. Members of a chemical family exhibited similar selectivities. The Hg++ ion appeared to be about a million times more strongly bound than the alkali metal ions. The relative binding of most of the metal ions varied with pH; the very tightly and very weakly bound ions showed the largest variations with pH. The calcium ion-hydrogen ion equilibrium was perturbed very little by the presence of the other ions. The separation factors and selectivity coefficients are discussed in terms of equilibrium and thermodynamic significance.
High-level radioactive waste generated from reprocessing processes will be disposed in a geological disposal that is deep underground. Calcium silicate hydrate is formed as a secondary mineral in the repository via the reaction of calcium ions leaching from the cement and the silicic acid dissolved from the host rocks. In this study, the sorption behavior of europium, which is also known as a chemical analog of americium, on calcium silicate hydrate was examined. The solid phase was analyzed via thermogravimetry- differential thermal analysis, differential scanning calorimetry, Raman spectroscopy, fluorescence spectroscopy, and fluorescence lifetime analysis. To understand the behavior of calcium silicate hydrate under conditions saturated with groundwater, the study samples were analyzed using the above methods, except for deferential scanning calorimetry, without a drying process. The results of the differential scanning calorimetry analyses showed that the temperatures for the endothermic peaks of calcium silicate hydrate for the lower Ca/Si ratios were larger than those for the higher Ca/Si ratios for coexistent conditions of europium ions. Hence, the relationships of the temperatures of the endothermic peaks and the Ca/Si ratios were reversed by the addition of europium ions. These study results suggest that calcium silicate hydrate can immobilize europium ions, thus preventing the production of colloidal forms. (authors)
Background and Purpose α4β2 nicotinic acetylcholine (nACh) receptors assemble in two stoichiometric forms, one of which is potentiated by calcium. The sites of calcium binding that underpin potentiation are not known. Experimental Approach To identify calcium binding sites, we applied cryo‐electron microscopy (cryo‐EM) and molecular dynamics (MD) simulations to each stoichiometric form of the α4β2 nACh receptor in the presence of calcium ions. To test whether the identified calcium sites are linked to potentiation, we generated mutants of anionic residues at the sites, expressed wild type and mutant receptors in clonal mammalian fibroblasts, and recorded ACh‐elicited single‐channel currents with or without calcium. Key Results Both cryo‐EM and MD simulations show calcium bound to a site between the extracellular and transmembrane domains of each α4 subunit (ECD‐TMD site). Substituting alanine for anionic residues at the ECD‐TMD site abolishes stoichiometry‐selective calcium potentiation, as monitored by single‐channel patch clamp electrophysiology. Additionally, MD simulation reveals calcium association at subunit interfaces within the extracellular domain. Substituting alanine for anionic residues at the ECD sites reduces or abolishes stoichiometry‐selective calcium potentiation. Conclusions and Implications Stoichiometry‐selective calcium potentiation of the α4β2 nACh receptor is achieved by calcium association with topographically distinct sites framed by anionic residues within the α4 subunit and between the α4 and β2 subunits. Stoichiometry‐selective calcium potentiation could result from the greater number of calcium sites in the stoichiometric form with three rather than two α4 subunits. The results are relevant to modulation of signalling via α4β2 nACh receptors in physiological and pathophysiological conditions.
Highlights: • PHD induces calcium release from cardiomyocytes through ryanodine channel. • PHD activates TRPA1 to induce extracellular calcium ions into the cell and further activate the ryanodine channel. • TRPA1 is involved in the regulation of PHD-Ca2+-AMPK signaling pathway. The proline hydroxylase domain-containing enzymes (PHDs) acts as cellular oxygen sensors, inducing a series of responses to hypoxia, especially during the regulation of metabolism and energy homeostasis. The increase of Ca{sup 2+} in cardiomyocytes, induced by the opening of PHD signaling pathway, is the key initiation signal necessary for the PHD-mediated regulation of the energy metabolism pathway, but the underlying molecular mechanism remains incompletely understood. This study used PHD inhibitors (PHIs) and PHD2-specific RNA interference (PHD2shRNA) to inhibit PHD signals in cardiomyocytes to explore whether transient receptor potential ankyrin 1 (TRPA1) is involved in the regulation of calcium ion influx in the PHD activation pathway associated with to AMP-activated protein kinase (AMPK). The Fluo-3AM probe was used to measure changes in free intracellular calcium ion concentrations, and Western blot analysis was used to detect the levels of phosphorylated (P)-AMPK, TRPA1, and P–Ca{sup 2+}/calmodulin-dependent protein kinase Ⅱ (CaMKⅡ) levels. The PHI-mediated inhibition of PHD resulted in an increase in free Ca{sup 2+} fluorescence in cardiomyocytes, which activated AMPK, TRPA1, and CaMKⅡ. The TRPA1 inhibitor HC030031, the CaMKII inhibitor KN93, and a ryanodine inhibitor (Ryanodine) were all able to inhibit the PHI-induced increase in intracellular Ca{sup 2+} and AMPK activation. Both PHIs and PHD2shRNA were able to effectively activate CaMKII and TRPA1. However, an inositol 1,4,5-triphosphate receptor (IP3R) inhibitor and the protein kinase A (PKA) inhibitor H89 did not significantly inhibit the PHI-induced increase in intracellular Ca{sup 2+} and AMPK activation. These results indicated that PHD might activate the CaMKⅡ pathway through the TRPA1 ion channel, inducing the release of calcium from the sarcoplasmic reticulum through ryanodine receptor 2 (RyR2), activating AMPK to initiate the protective effects of hypoxia in cardiomyocytes.
This study investigates the difference between the reactivity of slag in NaOH solution (w/s = 100) and in cement paste (w/b = 0.4). The reactivity of slag is much higher in NaOH solution than in cement paste. When the NaOH solution is saturated with portlandite, the rate of reaction of slag decreases to approach that in cement paste. This suggests that the slower reaction of slag in cement paste might be due to the presence of calcium ions released by the clinker phases. At 28 days, relative humidity measurements indicate that water is only present in pores less than 6 nm. Above 6 nm, hydration cannot take place due to the lack of water. From a thermodynamic point of view, the small size of water filled pores may slow down the slag reaction due to the high concentration of species in solution required for hydrate growth to balance the increase of the surface energy.
The urine processor assembly (UPA) on the International Space Station (ISS) recovers water from urine via a vacuum distillation process. The distillation occurs in a rotating distillation assembly (DA) where the urine is heated and subjected to sub-ambient pressure. As water is removed, the original organics, salts, and minerals in the urine become more concentrated and result in urine brine. Eventually, water removal will concentrate the urine brine to super saturation of individual constituents, and precipitation occurs. Under typical UPA DA operating conditions, calcium sulfate or gypsum is the first chemical to precipitate in substantial quantity. During preflight testing with ground urine, the UPA achieved 85% water recovery without precipitation. However, on ISS, it is possible that crewmember urine can be significantly more concentrated relative to urine from ground donors. As a result, gypsum precipitated in the DA when operating at water recovery rates at or near 85%, causing the failure and subsequent re14 NASA Tech Briefs, September 2013 placement of the DA. Later investigations have demonstrated that an excess of calcium and sulfate will cause precipitation at water recovery rates greater than 70%. The source of the excess calcium is likely physiological in nature, via crewmembers' bone loss, while the excess sulfate is primarily due to the sulfuric acid component of the urine pretreatment. To prevent gypsum precipitation in the UPA, the Precipitation Prevention Project (PPP) team has focused on removing the calcium ion from pretreated urine, using ion exchange resins as calcium removal agents. The selectivity and effectiveness of ion exchange resins are determined by such factors as the mobility of the liquid phase through the polymer matrix, the density of functional groups, type of functional groups bound to the matrix, and the chemical characteristics of the liquid phase (pH, oxidation potential, and ionic strength). Previous experience with ion exchange resins has demonstrated that the most effective implementation for an ion exchange resin is a cartridge, or column, in which the resin is contained. Based on the results of equilibrium and sub-scale dynamic column testing, a possible solution for mitigating the calcium precipitation issue on the ISS has been identified. From an original pool of 13 ion exchange resins, two candidates have been identified that demonstrate substantial calcium removal on the sub-scale. The dramatic reduction in resin performance from published calcium uptake demonstrates the need for thorough evaluation of resins at the low pH and strong oxidizing environment present in the UPA. Chemical variations in the influent (calcium concentrations and pretreatment dosing) appear to have a noticeable impact on the calcium capacity of the resin. Low calcium concentrations and high pretreatment dosing will likely result in a decrease in calcium capacity. Conversely, low pre trea t - ment dosing will likely result in an increase in calcium capacity. In contrast, investigations at a variety of flow rates, length-to-diameter ratios, resin volumes, and flow regimes (continuous versus pulsed) show that changes in physical parameters do not have substantial impacts on resin performance in the very low specific velocity ranges of interest. This result is particularly useful because most commercial applications at higher specific velocities do show a relatively strong relationship between flow and capacity. The lack of a strong relationship will allow more flexibility in the implementation of an ion exchange bed for flight. Verification of subscale tests with flight-scale resin beds is recommended prior to implementation in the on-orbit UPA.
A number of features of the gravitropic response of roots are not readily accounted for by the classical Cholodny-Went theory. These include the observations that (i) in the later stages of the response the growth gradient is reversed with no evident reversal of the auxin gradient; (ii) a major component of the acceleration of growth along the upper side occurs in the distal elongation zone (DEZ), a group of cells located between the meristem and the main elongation, not within the central elongation zone; and (iii) the initiation of differential growth in the DEZ appears to be independent of the establishment of auxin asymmetry. Alternative candidates for mediation of differential growth in the DEZ include calcium ions and protons. Gravi-induced curvature is accompanied by polar movement of calcium toward the lower side of the maize root tip and the DEZ is shown to be particularly sensitive to growth inhibition by calcium. Also, gravistimulation of maize roots causes enhanced acid efflux from the upper side of the DEZ. Evidence for gravi-induced modification of ion movements in the root tip includes changes in intracellular potentials and current flow. It is clear that there is more than one motor region in the root with regard to gravitropic responses and there is evidence that the DEZ itself consists of more than one class of responding cells. In order to gain a more complete understanding of the mechanism of gravitropic curvature, the physiological properties of the sub-zones of the root apex need to be thoroughly characterized with regard to their sensitivity to hormones, calcium, acid pH and electrical perturbations.
Characteristics of the regulation of calcium exchange in healthy persons exposed to 182 days of antiorthostatic hypokinesia are investigated. Total calcium concentrations, ionized calcium activities and parathyroid hormone concentrations in blood serum were determined, before, during, and up to 15 days after a 182-day period of strict bed rest at a head down tilt of 4 deg; and tests of blood urine responses to a calcium lactate stress were performed to study the role of the kidneys. An increase in calcium ion activity is observed during the period of hypokinesia, while total calcium concentrations changed to a lesser degree. Plasma parathyroid hormone levels are found to significantly exceed background levels during hypokinesia and in the recovery period immediately following. Finally, the increase in calcium excretion in the urine during prolonged limitations of muscular activity is found to be connected with both an enhancement of calcium filtration and a decrease in its reabsorption in the kidneys, possibly due to changes in hormonal regulation.