Search NASA⌕ Search

SEARCH · Search NASA

Results for “COMMERCIAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Polarization Type Potential Induced Degradation under Positive Bias in a Commercial PERC Module: Preprint

Potential induced degradation of the polarization type (PID-p) can reduce module performance in a relatively short period of time. PID-p can occur at both voltage polarities, but most studies are focused on degradation under a negative bias. This paper uses commercial bifacial passivated emitter and rear contact (PERC) cells within a monofacial glass-backsheet module construction to evaluate the impact of PID-p under a positive bias on the front side. Using the aluminum-foil (Al-foil) method, the module was stressed for PID in an environmental chamber. After the stress, the maximum power (Pmax) showed a decline of 3.1% at 1000 W/m2 and 6.2% at 200 W/m2. Recovery under light was also investigated. Complete recovery was observed at high irradiance, while a partial recovery was seen at lower irradiance. The outcomes of this study can help in understanding PID-p degradation under a positive bias and its recovery under the light.

PERC↗
DOE OSTI2026

Data for Optimization of Pre-Commercial Enzymes Dosage for a Potential Lignocellulosic Biorefinery

Lignocellulolytic enzymes remain one of the primary cost constraints in second-generation (2G) ethanol biorefineries. Achieving efficient hydrolysis of structural carbohydrates with minimal enzyme dosage, maintaining slurry fermentability for industrially relevant ethanol titers, and maximizing ethanol yield per ton of biomass are among the major challenges in 2G processes. In this study, we optimized the dosages of pre-commercial cellulase (NS22257) and hemicellulase (NS22244) on pilot-scale, hydrothermally pretreated lignocellulosic substrates. Enzyme dosages were evaluated at three levels: 20 mg of cellulase with 7.25 mg of hemicellulase (ED-1), 40 mg with 14.5 mg (ED-2), and 60 mg with 21.75 mg (ED-3). As expected, the highest sugar yields were obtained with ED-3; however, for sweet sorghum, oilcane, and miscanthus, sugar yields from ED-2 and ED-3 were not significantly different (p < 0.05). For example, sweet sorghum produced 123.78 ± 1.54 g L−1 and 125.76 ± 0.46 g L−1 of total sugars (glucose and xylose) with ED-2 and ED-3, respectively. Although energycane exhibited a statistically significant difference between ED-2 and ED-3, the incremental gain with ED-3 was modest, increasing sugar release by only 9.02 g L−1 relative to ED-2. Importantly, ED-1 resulted in sugar yields of 88.88 ± 3.64 to 106.86 ± 1.21 g L−1, sufficient to achieve ethanol titers ≥40 g L−1, the threshold required for industrial relevance. A semi-integrated bioprocess validated this outcome, producing 42.09 ± 2.38 g L−1 ethanol and an estimated yield of 213.38 L of ethanol per dry ton of pretreated biomass, requiring only 20.83 L of cellulase and 6.25 L of hemicellulase per ton. Remarkably, these enzyme dosages were approximately tenfold lower than those reported in prior studies.

Energycane↗
NASA NTRS2012

Use of Commercial Electrical, Electronic and Electromechanical (EEE) Parts in NASA's Commercial Crew Program (CCP)

NASA's Commercial Crew and Cargo Program (CCP) is stimulating efforts within the private sector to develop and demonstrate safe, reliable, and cost-effective space transportation capabilities. One initiative involves investigating the use of commercial electronic parts. NASA's CCP asked the NASA Engineering and Safety Center (NESC) to collect data to help frame the technical, cost, and schedule risk trades associated with electrical, electronic and electromechanical (EEE) parts selection and specifically expressed desire of some of the CCP partners to employ EEE parts of a lower grade than traditionally used in most NASA safety-critical applications. This document contains the outcome from the NESC's review and analyses.

Gonzalex, Oscar↗
NASA NTRS2013

ESO Commercial Microgravity Case Study 1: Novice Commercial Users (Medical) Vivo Biosciences Inc. - A Small Business Perspective

This case study was conducted in FY 2013 by the Emerging Space Office (ESO) to begin characterizing the kinds of opportunities and challenges encountered by small high-tech businesses who have never done RD in space and who serve terrestrial versus space markets, but who have legitimate business reasons for considering space research and development for generating novel or improved products. Vivo Biosciences Inc. (VBI) is an award winning company with a customer base that includes major pharmaceutical companies. However, despite a continuing series of successes, VBI believes that they are about at the limit of the performance their product can achieve on Earth and gravity is the problem. This Case Study documented VBI's experience as the novice company attempted its first steps in the process of conducting research and development in space. The report presents insights applicable to commercial suppliers of microgravity services as well as ISS support of new commercial users, especially small businesses interested in using space for product development.

Harper, Lynn D.↗
DOE OSTI2016

Evaluation of a commercially available passively Q-switched Nd:YAG laser with LiF:F-2(-) saturable absorber for laser-induced breakdown spectroscopy

Interest in passively Q-switched microchip lasers as a means for miniaturization of laser-induced breakdown spectroscopy (LIBS) apparatus has rapidly grown in the last years. To explore the possibility of using a comparatively UV-Vis transparent absorber, we herein present the first report on the evaluation of a commercially available flash lamp-pumped passively Q-switched Nd:YAG laser with LiF:F 2 - saturable absorber as an excitation source in LIBS. Quantitative measurements of barium, strontium, rubidium and lithium in granite, rhyolite, basalt and syenite whole-rock glass samples were performed. Ablation craters produced on a rock glass sample were characterized using a computerized X-ray tomography. Using a gated intensified benchtop spectrometer, limits of detection of 0.97, 23, 37, and 144 ppm were obtained for Li, Sr, Rb, and Ba, respectively. Finally, we discuss the advantages of using such a laser unit for LIBS applications in terms of ablation efficiency, analytical performances, output energy, and standoff capabilities.

36 MATERIALS SCIENCE↗
DOE OSTI2015

On filament structure and propagation within a commercial plasma globe

The filamentary discharge seen within commercial plasma globes is commonly enjoyed yet not well understood. Here, we investigate the discharge properties of a plasma globe using a variable high voltage amplifier. We find that increasing voltage magnitude increases the number of filaments while leaving their individual structure basically unchanged, a result typical of dielectric barrier discharges. The frequency of the voltage also affects filament population but more significantly changes filament structure, with more diffuse filaments seen at lower frequencies. Voltage polarity is observed to be important, especially at lower frequencies, where for negative-gradient voltages the discharge is more diffuse, not filamentary. At late stages of the discharge circular structures appear and expand on the glass boundaries. We find no trend of discharge speed with respect to voltage variables, though this may be due to manufacturer sample-to-sample variation. Each voltage cycle the discharge expands outward at ∼10–15 km/s, a speed significantly higher than the estimated electron drift yet considerably lower than that observed for most streamers. We discuss the physics of these observations and their relation to similar discharges that can be found within nature and industry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2016

Absolute dosimetric characterization of Gafchromic EBT3 and HDv2 films using commercial flat-bed scanners and evaluation of the scanner response function variability

Radiochromic films (RCF) are commonly used in dosimetry for a wide range of radiation sources (electrons, protons, and photons) for medical, industrial, and scientific applications. They are multi-layered, which includes plastic substrate layers and sensitive layers that incorporate a radiation-sensitive dye. Quantitative dose can be retrieved by digitizing the film, provided that a prior calibration exists. Here, to calibrate the newly developed EBT3 and HDv2 RCFs from Gafchromic™, we used the Stanford Medical LINAC to deposit in the films various doses of 10 MeV photons, and by scanning the films using three independent EPSON Precision 2450 scanners, three independent EPSON V750 scanners, and two independent EPSON 11000XL scanners. The films were scanned in separate RGB channels, as well as in black and white, and film orientation was varied. We found that the green channel of the RGB scan and the grayscale channel are in fact quite consistent over the different models of the scanner, although this comes at the cost of a reduction in sensitivity (by a factor ∼2.5 compared to the red channel). To allow any user to extend the absolute calibration reported here to any other scanner, we furthermore provide a calibration curve of the EPSON 2450 scanner based on absolutely calibrated, commercially available, optical density filters.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2014

Mixed-Potential NO x and NH 3 Sensors Fabricated by Commercial Manufacturing Methods [Mixed-Potential Sensors NO x and NH 3 Fabricated by Commercial Manufacturing Methods]

Meeting EPA Tier 3 emissions reduction requirements while simultaneously increasing fuel economy to meet new CAFE standards will require optimization of advanced combustion strategies and emissions control technologies. There is an immediate need for suitable exhaust gas sensor technologies to monitor internal combustion engine tailpipe emissions and to control and maintain efficient operation of the engine and exhaust after treatment systems. NH 3 , NO x , and HC sensors could enable onboard diagnostics and combustion control in lean-burn engines, analogous to the role of O 2 sensors in stoichiometric burn engines. Commercial manufacturing methods have been used to fabricate self-heated mixed-potential sensors in a planar automotive configuration. By altering materials composition and operating conditions, we are able to obtain sensitivity/selectivity to each NH 3 , NO x and HCs. In addition, these devices exhibit stable performance over months of testing as a result of the stable morphology of the electrode/electrolyte/gas three-phase interface.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A Database for Comparative Electrochemical Performance of Commercial 18650-Format Lithium-Ion Cells

Lithium-ion batteries are a central technology to our daily lives with widespread use in mobile devices and electric vehicles. These batteries are also beginning to be widely used in electric grid infrastructure support applications which have stringent safety and reliability requirements. Typically, electrochemical performance data is not available for modelers to validate their simulations, mechanisms, and algorithms for lithium-ion battery performance and lifetime. In this paper, we report on the electrochemical performance of commercial 18650 cells at a variety of temperatures and discharge currents. We found that LiFePO 4 is temperature tolerant for discharge currents at or below 10 A whereas LiCoO 2 , LiNi x Co y Al 1-x-y O 2 , and LiNi 0.80 Mn 0.15 Co 0.05 O 2 exhibited optimal electrochemical performance when the temperature is maintained at 15°C. LiNi x Co y Al 1-x-y O 2 showed signs of lithium plating at lower temperatures, evidenced by irreversible capacity loss and emergence of a high-voltage differential capacity peak. Furthermore, all cells need to be monitored for self-heating, as environment temperature and high discharge currents may elicit an unintended abuse condition. Overall, this study shows that lithium-ion batteries are highly application-specific and electrochemical behavior must be well understood for safe and reliable operation. Additionally, data collected in this study is available for anyone to download for further analysis and model validation.

25 ENERGY STORAGE↗