Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONCENTRATION RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1962

Study of Umbrella-Type Erectable Paraboloidal Solar Concentrators for Generation of Spacecraft Auxiliary Power

An investigation was made of some aspects of erectable umbrella-type paraboloidal solar-energy concentrators for use in spacecraft auxiliary power systems. An analysis is presented for the design of concentrators employing radial ribs and membrane-type coverings. The rib stiffness necessary to give a desired parabolic curvature upon erection is determined. Rib contour measurements were made in an upright and inverted position on an experimental 10-foot-diameter concentrator giving a focal length of 30.78 inches and 30.6 inches, respectively, as compared with a design focal length of 30 inches. Calorimetric tests employing spherical heat receivers showed a maximum geometrical concentrator efficiency of 75.3 percent with a concentration ratio of 92.2 at a focal length of approximately 30.5 inches. Within the scope of this investigation, it was found that, as the concentrator size increases, the weight per unit projected area increases, time to damp to one-half amplitude increases, and the natural frequency decreases. Umbrella-type solar concentrators appear to be feasible for power conversion systems using low concentration ratios; however, for large concentrators the time required to damp out disturbances may be a problem.

SPACECRAFT↗
NASA NTRS1989

Test results on parabolic dish concentrators for solar thermal power systems

This paper presents results of development testing of various solar thermal parabolic dish concentrators. The concentrators were mostly designed for the production of electric power using dish-mounted Rankine, Brayton or Stirling cycle engines, intended to be produced at low cost. Measured performance for various dishes included optical efficiencies ranging from 0.32 to 0.86 at a geometric concentration ratio of 500, and from about 0.09 to 0.85 at a geometric concentration ratio of 3000. Some malfunctions were observed. The tests should provide operating information of value in developing concentrators with improved performance and reduced maintenance.

Jaffe, Leonard D.↗
NASA NTRS2001

High-Efficiency Solar Thermal Vacuum Demonstration Completed for Refractive Secondary Concentrator

Common to many of the space applications that utilize solar thermal energy--such as electric power conversion, thermal propulsion, and furnaces--is a need for highly efficient, solar concentration systems. An effort is underway at the NASA Glenn Research Center to develop the refractive secondary concentrator, which uses refraction and total internal reflection to efficiently concentrate and direct solar energy. When used in combination with advanced lightweight primary concentrators, the refractive secondary concentrator enables very high system concentration ratios (10,000 to 1) and very high temperatures (>2000 K). The innovative refractive secondary concentrator offers significant advantages over all other types of secondary concentrators. The refractive secondary offers the highest throughput efficiency, provides for flux tailoring, requires no active cooling, relaxes the pointing and tracking requirements of the primary concentrator, and enables very high system concentration ratios. This technology has broad applicability to any system that requires the conversion of solar energy to heat. Glenn initiated the development of the refractive secondary concentrator in support of Shooting Star, a solar thermal propulsion flight experiment, and continued the development in support of Space Solar Power.

Wong, Wayne A.↗
NASA NTRS2012

FACT, Mega-ROSA, SOLAROSA

The Flexible Array Concentrator Technology (FACT) is a lightweight, high-performance reflective concentrator blanket assembly that can be used on flexible solar array blankets. The FACT concentrator replaces every other row of solar cells on a solar array blanket, significantly reducing the cost of the array. The modular design is highly scalable for the array system designer, and exhibits compact stowage, good off-pointing acceptance, and mass/cost savings. The assembly s relatively low concentration ratio, accompanied by a large radiative area, provides for a low cell operating temperature, and eliminates many of the thermal problems inherent in high-concentration-ratio designs. Unlike other reflector technologies, the FACT concentrator modules function on both z-fold and rolled flexible solar array blankets, as well as rigid array systems. Mega-ROSA (Mega Roll-Out Solar Array) is a new, highly modularized and extremely scalable version of ROSA that provides immense power level range capability from 100 kW to several MW in size. Mega-ROSA will enable extremely high-power spacecraft and SEP-powered missions, including space-tug and largescale planetary science and lunar/asteroid exploration missions. Mega-ROSA's inherent broad power scalability is achieved while retaining ROSA s solar array performance metrics and missionenabling features for lightweight, compact stowage volume and affordability. This innovation will enable future ultra-high-power missions through lowcost (25 to 50% cost savings, depending on PV and blanket technology), lightweight, high specific power (greater than 200 to 400 Watts per kilogram BOL (beginning-of-life) at the wing level depending on PV and blanket technology), compact stowage volume (greater than 50 kilowatts per cubic meter for very large arrays), high reliability, platform simplicity (low failure modes), high deployed strength/stiffness when scaled to huge sizes, and high-voltage operation capability. Mega-ROSA is adaptable to all photovoltaic and concentrator flexible blanket technologies, and can readily accommodate standard multijunction and emerging ultra-lightweight IMM (inverted metamorphic) photovoltaic flexible blanket assemblies, as well as ENTECHs Stretched Lens Array (SLA) and DSSs (Deployable Space Systems) FACT, which allows for cost reduction at the array level.

Spence, Brian↗
NASA NTRS1980

Time-average fluxes of heavy ions at the geostationary orbit

Measurements of average proton, helium, carbon, and oxygen fluxes at 6.6 earth radii are reported. The data represent averages obtained on ATS 6 between June 15 and Oct. 3, 1974. The energy range covered was 0.36-1.1 MeV for protons and approximately 1-4 MeV for the heavier ions. The results indicate that above about 1 MeV the heavier ion fluxes dominate over the proton flux on the energy/ion scale. Using two different spectral dependencies to fit the data, the carbon to oxygen concentration ratio for energies above 1 MeV was found to be 0.43 for the power law spectrum and 0.44 for the exponential spectrum. Thus in either case the abundance ratio is consistent with the solar origin of the particles. Similarly, the helium to oxygen concentration ratio is found to be 0.17 for the power law spectrum and 0.28 for the exponential spectrum. This is inconsistent with the solar wind ratio, which is about 10. The results quoted above are based on a very small portion of the distribution function above 1 MeV.

Konradi, A.↗
DOE OSTI2023

Electrochemical Performance of Mixed Redox-Active Organic Molecules in Redox Flow Batteries

Designing electrolytes based on mixture of different organic redox active molecules brings the opportunity of enhancing the volumetric energy density of flow batteries and removes the requirement of high solubility for individual organic species in the mixture. Here, in the present work, we conduct computational and experimental analysis to investigate the electrochemical performance of mixed redox-active organic molecules. A zero-dimensional transient model is employed to investigate the changes in the half-cell potential and the concentrations and partial currents of individual redox reactions in a mixture of organic molecules over time. The model demonstrates the effects of individual properties of species such as kinetic rate constants, mass transfer coefficients, concentration ratios and standard redox potentials and reports the effect of energy-losing homogenous chemical redox reaction on the voltage efficiency and concentration ratios of the mixed species. Pairs of anthraquinone negolyte species were selected for an experimental case study. A mixture of 2,6-N-TSAQ and 2,6-DHAQ showed 40% increase in the volumetric energy density compared to the performance of 2,6-DHAQ alone. Based on the results of the experimental and computational analysis, we propose guidelines for the design of suitable mixed redox-active organic species.

25 ENERGY STORAGE↗
NASA NTRS1981

Secondary and compound concentrators for parabolic dish solar thermal power systems

A secondary optical element may be added to a parabolic dish solar concentrator to increase the geometric concentration ratio attainable at a given intercept factor. This secondary may be a Fresnel lens or a mirror, such as a compound elliptic concentrator or a hyperbolic trumpet. At a fixed intercept factor, higher overall geometric concentration may be obtainable with a long focal length primary and a suitable secondary matched to it. Use of a secondary to increase the geometric concentration ratio is more likely to e worthwhile if the receiver temperature is high and if errors in the primary are large. Folding the optical path with a secondary may reduce cost by locating the receiver and power conversion equipment closer to the ground and by eliminating the heavy structure needed to support this equipment at the primary focus. Promising folded-path configurations include the Ritchey-Chretien and perhaps some three element geometries. Folding the optical path may be most useful in systems that provide process heat.

Jaffe, L. D.↗
DOE OSTI2023

Computational Fluid Dynamics Modeling of Solar Thermal Dry Reforming of Methane in a Parabolic Trough

Computational fluid dynamics simulations of solar-thermal dry reforming of methane using a parabolic trough configuration were performed. Parametric simulations of different combinations of gas flow rate, receiver tube emissivity, and geometric concentration ratio were conducted to determine configurations that could achieve the required catalyst temperatures of at least 700 °C to achieve high conversion of CH4 and CO2 to H2 and CO. Results showed that the concentration ratio of the parabolic trough collector had to be increased from ~70 to ~120 and the receiver-tube emissivity had to be reduced to ~0.2 to achieve bulk average catalyst temperatures of greater than 700 °C. Lower gas flow rates also reduced enthalpic heat losses and increased catalyst temperatures.

Ho, Clifford↗
DOE OSTI2023

Catalyzed oxidation of IG-110 nuclear graphite by simulated fission products Ag and Pd nanoparticles

To evaluate the stability of nuclear materials in high temperature gas reactors under air ingress conditions, catalytic oxidation of IG-110 graphite by two simulated fission products, metallic Pd and Ag, was studied in oxidative atmosphere and at temperatures up to 1000°C using an integrated furnace, mass spectroscopy and infrared spectroscopy system. Transmission electron microscopy and X-ray diffraction studies show that Pd and Ag nanoparticles were successfully introduced onto powdery IG-110 graphite through an impregnation and subsequent heat-treatment process. The combined mass spectroscopy and infrared spectroscopy methods allow simultaneous analysis of two gaseous products, CO and CO 2 , and separate measurements of activation energy for their formation reactions. It was found that the introduction of Pd or Ag to IG-110 graphite substantially catalyzed the oxidation of graphite, characteristic of decreased onset temperatures for the oxidation of graphite. Moreover, the catalytic effects by Pd and Ag are considerably different based on measured concentration ratios of CO 2 to CO as a function of oxidation temperatures. Ag makes the graphite oxidation commence at approximately 400°C with CO 2 being the dominant product. In contrast, Pd significantly increases the concentration ratio of CO 2 to CO at temperatures higher than approximately 690°C, although it decreases the onset temperature for the oxidation reaction to around 525°C. To understand the catalytic difference, the mechanism of the graphite oxidation was discussed based on the changes of surface oxygen species on Ag and Pd.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1975

Reactions of CH3, CH3O, and CH3O2 radicals with O3

Ozone was photolyzed at 253.7 nm at 25 and -52 degrees in the presence of CH4 and O2 to measure the reactions of O3 with CH3, CH3O, and CH3O2. The O(1D) atoms produced in the primary photochemical act react with CH4 to give CH3 radicals which in turn can react with O2 to give CH3O2 and CH3O radicals. At very high O2 to O3 concentration ratios, the quantum yield of O3 disappearance approached 1.0, indicating that O3 reactions with CH3O2 and CH3O are slow. Upper limits to the rate coefficients at 25 degrees were computed. At lower values of the concentration ratio, chain decomposition of O3 occurred which could be explained by the reaction of O3 with CH3 radicals to produce CH2O, O2, and H atoms all the time. The two routes to these products are considered, and the preferred reaction channel is found.

Simonaitis, R.↗
NASA NTRS1978

Solar concentration properties of flat fresnel lenses with large F-numbers

The solar concentration performances of flat, line-focusing sun-tracking Fresnel lenses with selected f-numbers between 0.9 and 2.0 were analyzed. Lens transmittance was found to have a weak dependence on f-number, with a 2% increase occuring as the f-number is increased from 0.9 to 2.0. The geometric concentration ratio for perfectly tracking lenses peaked for an f-number near 1.35. Intensity profiles were more uniform over the image extent for large f-number lenses when compared to the f/0.9 lens results. Substantial decreases in geometri concentration ratios were observed for transverse tracking errors equal to or below 1 degree for all f-number lenses. With respect to tracking errors, the solar performance is optimum for f-numbers between 1.25 and 1.5.

Cosby, R. M.↗
NASA NTRS1974

EPR measurement of the effect of glass composition on the oxidation states of europium

An investigation was conducted concerning the dependence of the concentration ratio of Eu(2+) to Eu(3+) on composition for silicate liquids whose compositional end members are CaAl2Si2O8 and MgSiO3, MG2SiO4, CaMgSi2O6, CaMgSiO4, CaSiO3, or Ca2SiO4. The liquids were quenched to produce glasses. An electron paramagnetic resonance spectrometer was used to determine the concentration ratios of Eu(2+) to Eu(3+) in the glasses.

Morris, R. V.↗
DOE OSTI2022

Best practices for predictions of radionuclide activity concentrations and total absorbed dose rates to freshwater organisms exposed to uranium mining/milling

Predictions of radionuclide dose rates to freshwater organisms can be used to evaluate the radiological environmental impacts of releases from uranium mining and milling projects. These predictions help inform decisions on the implementation of mitigation measures. The objective of this study was to identify how dose rate modelling could be improved to reduce uncertainty in predictions to non-human biota. For this purpose, we modelled the activity concentrations of 210 Pb, 210 Po, 226 Ra, 230 Th, and 238 U downstream of uranium mines and mills in northern Saskatchewan, Canada, together with associated weighted absorbed dose rates for a freshwater food chain using measured activity concentrations in water and sediments. Differences in predictions of radionuclide activity concentrations occurred mainly from the different default partition coefficient and concentration ratio values from one model to another and including all or only some 238 U decay daughters in the dose rate assessments. Consequently, we recommend a standardized best-practice approach to calculate weighted absorbed dose rates to freshwater biota whether a facility is at the planning, operating or decommissioned stage. At the initial planning stage, the best-practice approach recommend using conservative site-specific baseline activity concentrations in water, sediments and organisms and predict conservative incremental activity concentrations in these media by selecting concentration ratios based on species similarity and similar water quality conditions to reduce the uncertainty in dose rate calculations. At the operating and decommissioned stages, the best-practice approach recommends relying on measured activity concentrations in water, sediment, fish tissue and wholebody of small organisms to further reduce uncertainty in dose rate estimates. This approach would allow for more realistic but still conservative dose assessments when evaluating impacts from uranium mining projects and making decision on adequate controls of releases.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

Quantifying the thermal effect and methyl radical production in nanosecond repetitively pulsed glow discharges applied to a methane-air flame

In this work, we investigated non-equilibrium plasma produced by nanosecond repetitively pulsed glow discharges applied across a lean premixed methane-air flame. The flame is stationary, axisymmetric, and laminar. The discharges are applied on the symmetry axis crossing the reactant gases, flame front, and product gases, allowing phase-locked averaged measurements and comparisons with axisymmetric numerical simulations. The thermal effect and methyl radical production are quantified in the discharge in the reactant gas region. One-dimensional, two-beam, hybrid, femtosecond-picosecond, coherent anti-Stokes Raman scattering is used to acquire spatial and temporal profiles of temperature and oxygen-to-nitrogen concentration ratio. Photo-fragmentation laser-induced fluorescence is used to acquire quantitative two-dimensional profiles of methyl radicals in the discharge providing the first quantitative imaging of methyl produced ahead of a flame by plasma-induced methane dissociation. The spatial profiles of temperature and oxygen-to-nitrogen concentration ratio are in steady state, indicating that individual discharges have an insignificant heating effect. Upper and lower bounds of the produced mole fraction of methyl radicals in the plasma are obtained due to uncertainties in the collisional quenching rates of excited state methylidyne radicals in the plasma. The discharges produce a maximum of 600–1100 ppm of methyl radicals upstream of the flame front within 25 ns. This amount is similar to the predicted methyl mole fraction for the flame without plasma and thus represents a significant chemical perturbation to the reactants upstream of the flame front. The produced methyl follows an exponential decay in the first microsecond after the discharge with a decay constant of 8 µs close to the flame, and 0.8 µs further from the flame. The decay then deviates from the exponential curve and the methyl persists for tens of microseconds. The results suggest that for the tested configuration, the thermal effect of individual discharges through fast gas heating is negligible, while active chemical species are produced in large quantities in the reactant gases, upstream of the flame front.

hybrid fs-ps CARS↗
NASA NTRS1983

Relative rate constants for the reactions of atomic oxygen with HO2 anad OH radicals

Relative rate constants for the reactions O + HO2 - OH + O2 (1) and O + OH - H + O2 (2) were obtained by using the discharge-flow resonance fluorescence technique at 2 torr total pressure and 299 K. HO2 radicals were generated by reacting atomic hydrogen with an excess of O2. Quasi-steady-state concentrations of OH and HO2 were established in the presence of excess atomic oxygen. Observed concentration ratios, namely the ratio of the OH concentration to the HO2 concentration, resulted in a value of 1.7 + or 0.2 for k1/k2. The error limits are twice the standard deviation obtained from the data analysis. Overall experimental error is estimated to be + or - 25 percent. This result confirms earlier direct measurements of k1 and k2 which required knowledge of absolute radical or atomic oxygen concentrations.

Keyser, L. F.↗
NASA NTRS1987

Structural concepts for large solar concentrators

The Sunflower large solar concentrator, developed in the early 1970's, is a salient example of a high-efficiency concentrator. The newly emphasized needs for solar dynamic power on the Space Station and for large, lightweight thermal sources are outlined. Existing concepts for high efficiency reflector surfaces are examined with attention to accuracy needs for concentration rates of 1000 to 3000. Concepts using stiff reflector panels are deemed most likely to exhibit the long-term consistent accuracy necessary for low-orbit operation, particularly for the higher concentration ratios. Quantitative results are shown of the effects of surface errors for various concentration and focal-length diameter ratios. Cost effectiveness is discussed. Principal sources of high cost include the need for various dished panels for paraboloidal reflectors and the expense of ground testing and adjustment. A new configuration is presented addressing both problems, i.e., a deployable Pactruss backup structure with identical panels installed on the structure after deployment in space. Analytical results show that with reasonable pointing errors, this new concept is capable of concentration ratios greater than 2000.

Hedgepeth, John M.↗
NASA NTRS1994

Influence of plumes from biomass burning on atmospheric chemistry over the equatorial and tropical South Atlantic during CITE 3

During all eight flights conducted over the equatorial and tropical South Atlantic in the course of the Chemical Instrumentation Test and Evaluation (CITE 3) experiment, we observed haze layers with elevated concentrations of aerosols, O3, CO, and other trace gases related to biomass burning emissions. They occurred at altitudes between 1000 and 5200 m and were usually only some 100-300 m thick. These layers extended horizontally over several 100 km and were marked by the presence of visible brownish haze. Air mass trajectories indicate that these layers originate in the biomass burning regions of Africa and South America and typically have aged at least 10 days since the time of emission. In the haze layers, O3 and CO concentrations up to 90 and 210 ppb were observed, respectively. The two species were highly correlated. The ratio concentrations in plume minus background concentrations of O3/CO is typically in the range 0.2-0.7, much higher than the ratios in the less aged plumes investigated previously in Amazonia. In most cases, aerosol (0.12-3 micrometer diameter) number concentrations were also elevated by up to 400/cu cm in the layers; aerosol enrichments were also strongly correlated with elevated CO levels. Clear correlations between CO and NO(x) enrichments were not apparent due to the age of the plumes, in which most NO(x) would have already reacted away within 1-2 days. Only in some of the plumes could clear correlations between NO(y) and CO be identified; the absence of a general correlation between NO(y) and CO may be due to instrumental limitations and to variable sinks for NO(y). The average enrichment of the ratio concentrations in plume minus background concentrations of NO(y)/CO was quite high, consistent with the efficient production of ozone observed in the plumes. The chemical characteristics of the haze layers, together with remote sensing information and trajectory calculations, suggest that fire emissions (in Africa and/or South America) are the primary source of the haze layer components.

Andreae, M. O.↗
NASA NTRS1997

Design and Fabrication of a Dielectric Total Internal Reflecting Solar Concentrator and Associated Flux Extractor for Extreme High Temperature (2500K) Applications

The Analex Corporation, under contract to the NASA Lewis Research Center (LeRC), Cleveland, Ohio, recently evaluated the feasibility of utilizing refractive secondary concentrators for solar heat receivers operating at temperatures up to 2500K. The feasibility study pointed out a number of significant advantages provided by solid single crystal refractive devices over the more conventional hollow reflective compound parabolic concentrators (CPCs). In addition to the advantages of higher concentration ratio and efficiency, the refractive concentrator, when combined with a flux extractor rod, provides for flux tailoring within the heat receiver cavity. This is a highly desirable, almost mandatory, feature for solar thermal propulsion engine designs presently being considered for NASA and Air Force thermal applications. Following the feasibility evaluation, the NASA-LeRC, NASA-Marshall Space Flight Center (MSFC), and Analex Corporation teamed up to design, fabricate, and test a refractive secondary concentrator/flux extractor system for potential use in the NASA-MSFC "Shooting Star" flight experiment. This paper describes the advantages and technical challenges associated with the design methodologies developed and utilized and the material and fabrication limitations encountered.

Soules, Jack A.↗