Search NASA⌕ Search

SEARCH · Search NASA

Results for “CONSUMABLES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Catalytic conversion of post-consumer recycled high-density polyethylene oil over Zn-impregnated ZSM-5 catalysts

The catalytic conversion of post-consumer recycled high-density polyethylene (PCR-HDPE) pyrolysis oil was investigated using modified ZSM-5 zeolites, prepared under different conditions. The PCR-HDPE oil, obtained through pyrolysis at 500 °C followed by distillation at 165 °C, contained a naphtha fraction hydrocarbons suitable for catalytic upgrading. H/ZSM-5 converts PCR-HDPE naphtha fraction oil primarily into BTX, along with light paraffins and olefins. Introducing mesoporosity led to increased propylene yield at the expense of BTX. Zn impregnation onto H/ZSM-5 and H-meso/ZSM-5 enhanced BTX yield by up to 13 %. However, Zn-meso/ZSM-5 exhibited a lower BTX yield than Zn/ZSM-5 with the same Zn loadings, especially after additional steam treatment at 700 °C. Spent catalysts revealed no noticeable increase in metal contaminants such as calcium and aluminum that were present in the PCR-HDPE. Here, the Zn/ZSM-5 catalyst was stable for more than 50 h time on stream and showed promising potential for upgrading PCR-HDPE naphtha fraction oils.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Control of Weld Residual Stress in a Thin Steel Plate through Low Transformation Temperature Welding Consumables

Low transformation temperature welding (LTTW) consumables are characterized by a low martensite start temperature and a large fraction of martensite forming in the weld. It can efficiently reduce the tensile residual stress because the volume expansion associated with the martensitic transformation compensates for the thermal contraction during cooling. In this work, a LTTW wire, designated as EH200B, was created for the arc welding of advanced high-strength steel thin plates. In comparison to conventional ER70S-3 wires, this LTTW wire generated an opposite distortion pattern. Neutron diffraction measurements along the center thickness of the welded plates showed the maximum residual stress along the longitudinal direction (LD) in the weld region, and the heat-affected zone (HAZ) immediately adjacent to the weld region was reduced from ~330 MPa to below 240 MPa by using the LTTW wire. A finite element (FE) model was developed to predict the residual stress distributions of the plates welded under these two wires. The simulation results showed reasonable agreement with the volume-average neutron diffraction data. Compressive residual stress in the weld region using the LTTW wire was predicted by the FE method. Electron backscattered diffraction and x-ray diffraction measurements confirmed ~90% martensite was present in the LTTW weld. The fatigue life of DP980 steel lap joint panels using EH200B wire nearly doubled that of ER70S-3 wire. This improvement was attributed to the high strength and low LD residual stress in the weld and HAZ immediately adjacent to the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electric Vehicles for Consumers

More consumers are choosing electric vehicles (EVs) as new, competitively priced models with longer ranges hit the market. More public charging stations are also rapidly becoming available, and some offer quick charges to get drivers back on the road in minutes. New EVs are released all the time, with models designed to meet a wider variety of needs. To learn whether an EV is right for you, assess your driving requirements, available vehicles, and cost considerations. Easily compare costs and benefits of specific vehicles using the FuelEconomy.gov vehicle comparison tool.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2023

Electric Vehicles for Consumers

More consumers are choosing electric vehicles (EVs) as new, competitively priced models with longer ranges hit the market. More public charging stations are also rapidly becoming available, and some offer quick charges to get drivers back on the road in minutes. New EVs are released all the time, with models designed to meet a wider variety of needs. To learn whether an EV is right for you, assess your driving requirements, available vehicles, and cost considerations. Easily compare costs and benefits of specific vehicles using the FuelEconomy.gov vehicle comparison tool.

charging↗
DOE OSTI2025

Repurposing Post-Consumer Polyethylene to Access Cross-Linked Polyethylene with Reprocessabilty, Recyclability, and Tunable Properties

Polyethylene (PE) is the most widely produced plastic but accumulation and resistance to degradation has significantly contributed to the plastic waste crisis. Upcycling has presented promising solutions to transform PE waste into value-added products. In this study, mixed post-consumer PE was successfully repurposed into reprocessable and chemically recyclable cross-linked polyethylene (XLPE). This process involved converting PE into telechelic oligomers, followed by repolymerization using a hybrid cross-linking system consisting of a dynamic cross-linker 2,4,6-triethoxy-1,3,5-triazine (TETA) and non-dynamic cross-linker tris(6-isocyanatohexyl)isocyanurate (Tri-HDI). In the resulting XLPE, TETA facilitated iterative reprocessing with minimal property degradation across cycles, whereas Tri-HDI helped preserve functional performance throughout service life. Compared to PE, XLPE exhibited enhanced mechanical properties, reduced creep deformation under application-relevant temperatures, and high temperature structural stability. Notably, copolymerizing PE oligomers with commercial macrodiols was employed to create composite XLPEs, enabling tuning material properties. After use, XLPE can be efficiently and selectively depolymerized under mild conditions, even when mixed with commercial insulator cables. This depolymerization allows for the recovery of the constituent building blocks, enabling purification and subsequent repolymerization for reuse. This approach demonstrates the potential of repurposing plastic waste into sustainable materials and fostering the development of a circular economy.

INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CHEMI↗
DOE OSTI2024

Evaluating consumer 3D printing nozzles as a low cost alternative for mesophase pitch-derived carbon fiber production

Synthetic fibers, such as Kevlar fibers, SiC fibers, and carbon fibers, are essential components for constructing high performance structures. Whether for engineering, sports, energy storage (batteries and supercapacitors), or aerospace applications, fiber microstructure plays a critical role in fiber properties and functionalities. However, studying fiber nozzle configurations and spinning parameters to achieve the desired microstructure remains challenging, costly, and time consuming. Here, mesophase pitch-derived fibers were used as an example to demonstrate that low cost, commercially available 3D printer nozzles can “print” fibers. Four different nozzles were used to “print” fibers and the effects of their features on fiber properties were observed and compared to other lab spun and commercial pitch- derived CF. A longer orifice length resulted in higher modulus fiber whereas a larger draw-down ratio yielded a stronger fiber. Furthermore, the findings provide a new opportunity for 3D printer hardware application and open up opportunities for developing low-cost fibers.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Aqueous buffer solution-induced crystallization competes with enzymatic depolymerization of pre-treated post-consumer poly (ethylene terephthalate) waste

In this paper, the complex relationship between kinetics and substrate morphology during enzymatic depolymerization of melt processed poly(ethylene terephthalate) (PET) is explored and the effects of competing transformations are analyzed. Extruded PET substrates from post-consumer recycled PET (RPET) bottles flakes subjected to enzymatic depolymerization are examined to reveal increases in crystallinity from ~10% post-extrusion to >30% after 3 days of depolymerization as well as increases in glass transition temperature (T g ) from ~66°C to > 80°C. Further investigation into this behavior shows that post-extrusion RPET substrates do not exhibit changes in crystallinity when subjected to dry annealing at 65°C in an oven over 7 days, but they do experience annealing in depolymerization buffer solution with no enzymes at 65°C within 3 days. This difference may be attributed to plasticization of PET in the presence of water, also known as solvent induced crystallization. The impact of this plasticized annealing behavior is demonstrated by subjecting RPET substrates to increasing enzyme-to-substrate loads. As enzyme load increases, overall conversion of substrates increases despite crystallinity also increasing to similar levels regardless of the initial enzyme loading. The competition between depolymerization and crystallization suggests that the rate at which PET substrates are depolymerized at the operational temperature is integral to achieving high conversion to monomeric product. This, in turn, also suggests that savings from lowered enzyme loadings may be more detrimental than helpful in pursuing the most cost-effective recycling systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Alloy selective optical sorting of mixed post-consumer aluminum scrap streams

Shredded post-consumer non-ferrous scrap stream, also known as Zorba, contains a mixture of cast and wrought aluminum pieces with very different compositions. Cast Al pieces, with their high Si, Cu and Fe content, are a major contaminant in wrought scrap fraction, which results in downcycling of the mixed cast + wrought scrap into non-structural cast Al alloys and parts. Here, in this paper, we introduce a chemical treatment method to color-code scrap aluminum pieces by alloy family and demonstrate low-cost optical sorting of cast from wrought pieces to upgrade the scrap stream. We utilized non-acidic chemical solutions that react with (i.e., etch) the scrap pieces to produce colors based on the Al alloy chemistry of a given piece. Cast pieces with high Si and Cu fractions turned black, whereas the much leaner wrought pieces remained unreacted. We showed > 95% sorting efficiency of mixed cast and wrought pieces using a repurposed low-cost optical sorter originally designed for food sorting. We also colored wrought Al pieces by alloy families, such as 5xxx and 6xxx, using a two-step chemical etching technique, which has the potential to create a circular supply chain in which wrought aluminum alloys are sorted from the mixed scrap stream and recycled back to high-value wrought products such as sheets, extrusions, and forgings with minimal contamination from cast scrap.

Aluminum↗
DOE OSTI2026

Production of high-quality polyethylene (PE) films from post-consumer shrink wrap with solvent targeted recovery and precipitation (STRAP)

The solvent-targeted recovery and precipitation (STRAP™) process separates polymers from contaminants present in the feedstock. In this work, we demonstrate the recyclability of a post-consumer waste (PCW) shrink wrap that contains inks, adhesives, and paper using STRAP. We produced a clear rPE cast film from the PCR shrink wrap with no visual contamination from paper or inks. STRAP decreased the ash content from 0.96 wt% to 0.24 wt%. A techno-economic analysis (TEA) shows that a STRAP plant processing 50,000 metric tons annually of shrink wrap waste (purchased at $\$0.25$/kg) containing 85 wt% PE can achieve an IRR of 16.2% when selling rPE at $\$1.30$/kg, an IRR of 10.7% with an rPE price of $\$1.00$/kg, or an IRR of 3.79% with an rPE price of $\$0.70$/kg. Furthermore, the life cycle assessment (LCA) shows a 64% reduction in global warming potential (kg CO 2 equivalent) when compared to the production of virgin LDPE. As a result, this work shows how feedstocks with insoluble impurities can be recycled using STRAP on a large scale.

Radkevich, Elizaveta [University of Wisconsin-Madi↗
DOE OSTI2022

Regional economic potential for recycling consumer waste electronics in the United States

Waste electronics are a growing environmental concern but also contain materials of great economic value. If properly recycled, waste electronics could enhance the sustainability of vital metal supply chains by offsetting the increasing demand for virgin mining. However, rapid changes in the size and composition of electronics complicate their end-of-life management. Here we couple material flow and geospatial analyses on over 90 critical consumer electronic products and find that over 1 billion devices, representing up to 1.5 million tonnes of mass, could be discarded annually in the United States by 2033. Emerging electronics such as connected home, health and augmented/virtual reality devices have become the fastest-growing types in the waste stream. Here we highlight policy opportunities to develop various sustainable circularity strategies around metal supply chains by showing the potential to integrate waste electronics and virgin mining pathways in western US regions, while new infrastructure designed specifically for waste electronics treatment is favourable in the central and eastern United States. Furthermore, we show the importance of building national-level refining and tear-down databases to improve electronics end-of-life management in the next decade.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Ultra-high SERS detection of consumable coloring agents using plasmonic gold nanostars with high aspect-ratio spikes

Solution-based SERS detection by using a portable Raman instrument has emerged as an important tool due to its simplicity, and flexibility for rapid and on-site screening of analyte molecules. However, this method has several shortcomings, including poor sensitivity especially for weak-affinity analyte molecules, where there is no close contact between the plasmonic metal surface and analyte molecule. Examples of weak-affinity molecules include pigment molecules that are commonly used as a consumable coloring agent, such as allura red (AR), and sunset yellow (SY). As high consumption of colorant agents has been shown to cause adverse effects on human health, there is a strong need to develop a simple and practical sensing system with high sensitivity for these agents. Here we present a novel, highly sensitive solution-based SERS detection method for AR, and SY by using CTAC capped gold nanostars (GNS) having different aspect ratios (GNS-2, GNS-4, and GNS-5) without utilizing any aggregating agents which can enhance SERS signal however it reduces batch to batch reproducibility. The influence of the aspect ratio of GNS on SERS properties was investigated. We have achieved a limit of detection (LOD) of AR and SY as low as 0.5 and 1 ppb, respectively by using GNS-5 with the advantages of minimal sample preparation by just mixing the analyte solution into a well plate containing GNS solution. In addition, excellent colloidal stability and reproducibility have further enhanced the applicability in real-world samples. Altogether, our results evidence that the solution-based SERS detection platform using high aspect-ratio GNS can be applied for practical application to detect pigment molecules in real samples with satisfactory results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A Comprehensive Scheduling Framework using SP-ADMM for Residential Demand Response with Weather and Consumer Uncertainties

This paper presents a comprehensive scheduling framework for residential demand response (DR) programs considering both the day-ahead and real-time electricity markets. In the first stage, residential customers determine the operating status of their responsive devices such as heating, ventilation, and air conditioning (HVAC) systems and electric water heaters (EWHs), while the distribution system operator (DSO) computes the amount of electricity to be purchased in the day-ahead electricity market. In the second stage, the DSO purchases insufficient (or sells surplus) electricity in the real-time electricity market to maintain the supply-demand balance. Due to its computational complexity and data privacy issues, the proposed model cannot be directly solved in a centralized manner, especially with a large number of uncertain scenarios. Therefore, this paper proposes a combination of stochastic programming (SP) and the alternating direction method of multipliers (ADMM) algorithm, called SP-ADMM, to decompose the original model and then solve each sub-problem in a distributed manner while considering multiple uncertain scenarios. The simulation study is performed on the IEEE 33-bus system including 121 residential houses. Here, the results demonstrate the effectiveness of the proposed approach for large-scale residential DR applications under weather and consumer uncertainties.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2022

California Consumers’ Beliefs and Trust in Electric Utilities

The authors use survey and interview data from California homeowners to understand customers’ trust in their utility company. The authors find that customers’ beliefs about the reliability of electricity do not predict trust. Instead, what matters are beliefs that the utility company does a bad job managing customer service, costs, and wildfires. Distrust among survey respondents aligns with interview participants’ descriptions of utility companies as powerful, greedy monopolies that benefit themselves at the expense of helpless consumers. These results have implications for the energy transition and, more generally, understanding potential challenges experienced by technocratic institutions.

Horne, Christine↗
DOE OSTI2020

Plug-In Electric Vehicle Showcases: Consumer Experience and Acceptance

In 2016 the U.S. Department of Energy's (DOE) Office of Energy Efficiency and Renewable Energy's Vehicle Technologies Office (VTO) announced three awardees to hold plug-in electric vehicle (PEV) showcases to demonstrate available technologies and provide a hands-on consumer experience at conveniently located, brand-neutral settings. The events varied in style from long term stationary storefront settings to weekend events at a variety of regional venues. Attendees could interact with the technology through ride-and-drives and longer-term test drives. The events began in the spring of 2017 and continued through 2019.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Dishwashers in the Residential Sector: A Survey of Product Characteristics, Usage, and Consumer Preferences

Data on consumer purchasing decisions, usage, and behaviors relating to residential appliances help to inform technical and economic analyses related to the energy and water used by those appliances, including dishwashers. Existing publicly available data for dishwashers include two regularly conducted national surveys that describe dishwasher ownership and usage. The United States (US) Department of Energy’s (DOE) Energy Information Administration’s Residential Energy Consumption Survey (RECS) records the presence of a dishwasher in the home, the numbers of times per week the dishwasher is operated, and the dishwasher age, along with household demographic characteristics. The US Census Bureau’s American Housing Survey (AHS) also records the presence of a dishwasher in the home along with household demographic characteristics.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

LiDAR-Aided Interior Orientation Parameters Refinement Strategy for Consumer-Grade Cameras Onboard UAV Remote Sensing Systems

Unmanned aerial vehicles (UAVs) are quickly emerging as a popular platform for 3D reconstruction/modeling in various applications such as precision agriculture, coastal monitoring, and emergency management. For such applications, LiDAR and frame cameras are the two most commonly used sensors for 3D mapping of the object space. For example, point clouds for the area of interest can be directly derived from LiDAR sensors onboard UAVs equipped with integrated global navigation satellite systems and inertial navigation systems (GNSS/INS). Imagery-based mapping, on the other hand, is considered to be a cost-effective and practical option and is often conducted by generating point clouds and orthophotos using structure from motion (SfM) techniques. Mapping with photogrammetric approaches requires accurate camera interior orientation parameters (IOPs), especially when direct georeferencing is utilized. Most state-of-the-art approaches for determining/refining camera IOPs depend on ground control points (GCPs). However, establishing GCPs is expensive and labor-intensive, and more importantly, the distribution and number of GCPs are usually less than optimal to provide adequate control for determining and/or refining camera IOPs. Moreover, consumer-grade cameras with unstable IOPs have been widely used for mapping applications. Therefore, in such scenarios, where frequent camera calibration or IOP refinement is required, GCP-based approaches are impractical. To eliminate the need for GCPs, this study uses LiDAR data as a reference surface to perform in situ refinement of camera IOPs. The proposed refinement strategy is conducted in three main steps. An image-based sparse point cloud is first generated via a GNSS/INS-assisted SfM strategy. Then, LiDAR points corresponding to the resultant image-based sparse point cloud are identified through an iterative plane fitting approach and are referred to as LiDAR control points (LCPs). Finally, IOPs of the utilized camera are refined through a GNSS/INS-assisted bundle adjustment procedure using LCPs. Seven datasets over two study sites with a variety of geomorphic features are used to evaluate the performance of the developed strategy. The results illustrate the ability of the proposed approach to achieve an object space absolute accuracy of 3–5 cm (i.e., 5–10 times the ground sampling distance) at a 41 m flying height.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Consumer-Oriented Energy Use and Range Metrics for Battery Electric Vehicles

The present study was motivated by a need to expand information for consumers offered through the FuelEconomy.Gov website. To that end, a power-based modeling approach has been used to examine the effect of steady-speed driving on estimated range for model year 2020 – 2023 battery electric vehicles (BEVs). This approach allowed rapid study of a broader range of BEV models than could be accomplished through vehicle tests. Publicly accessible certification test results and other data were used to perform a regression between cycle-average tractive power requirements and the resulting electrical power. Importantly, this regression enabled estimation of electric power and energy use over a range of steady highway speeds. These analyses in turn allowed projection of vehicle range at differing speeds. The projections agree within 6% with available 65 MPH manufacturer test data. Analyses of vehicles from model years 2020 – 2023 show that the 5-cycle range and energy use values from the window stickers of new vehicles are reasonable values for steady-speed driving at 65 MPH. Range decreases by a median value of approximately 15% for each 10 MPH increase in speed. The 5-cycle energy use (in kW-Hr / 100 miles) and energy economy (in miles / kW-Hr) derived from the 5-cycle energy use are reasonable estimates for 65 MPH steady speed driving. Energy economy decreases by about 0.5 miles / kW-Hr for every 10 MPH increase in speed.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Development of Post-Consumer Textile Waste Degradation Protocol and Related Downstream Transformations: Cooperative Research and Development (Final Report)

Tereform, Inc. (Tereform) is developing molecular deconstruction processes to transform waste materials into chemical building blocks. During the CRADA, Tereform deconstructed real-world post-consumer substrates into chemical monomers, validated their performance on laboratory scales, demonstrated feasibility of the degradation products in downstream transformations, and successfully scaled the reaction to kilogram-scale. These results were used to develop and refine technoeconomic analysis and lifecycle assessments to evaluate the economic feasibility and environmental impacts of the process.

36 MATERIALS SCIENCE↗