Search NASA⌕ Search

SEARCH · Search NASA

Results for “CORE FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Hydrogen, Methane, Brine Flow Behavior, and Saturation in Sandstone Cores During H 2 and CH 4 Injection and Displacement

Large-scale underground hydrogen storage (UHS) is a critical component in the emerging hydrogen economy. Knowledge of multiphase flow behavior involving hydrogen in storage reservoir formations is crucial to characterizing hydrogen transport properties and essential for the deliverability and storage operations of UHS. There are still many gaps in fully understanding hydrogen–methane–brine multiphase phase flow that require further investigation. In this work, H 2 and CH 4 were injected through brine-saturated sandstone cores using a tri-axial core holder system fitted with flow rate meters and pressure transducers, while the effluent gas concentrations were analyzed using an online micro gas chromatograph. Brine displacement, permeability, and gas breakthrough curves were measured. We studied the flow behavior of hydrogen and methane in sandstone cores through testing brine displacement by gas injection and comparing the hydrogen displacement of methane with the methane displacement of hydrogen. We also tested the differences between horizontal and vertical flow in brine displacement. The results showed that brine displacement was more efficient in a core with higher permeability and porosity, resulting in a higher initial gas saturation. A higher gas injection rate brought about faster gas breakthrough measured by pore volume and sharper concentration curves. Hydrogen did not exhibit abnormal flow in the sandstone when the flow was horizontal and downward vertical. Gas overriding was observed in brine displacements when the flow was horizontal, with hydrogen showing this behavior more profoundly compared to methane. Downward vertical gas injection induced higher efficiency brine displacement compared to horizontal displacement and resulted in a higher initial gas saturation in the sandstone cores. These findings address critical knowledge gaps regarding gas flow patterns and displacement behaviors during hydrogen injection and recovery phases in UHS facilities using methane as the cushion gas. The insights from this research offer valuable guidance for optimizing UHS systems, ensuring operational efficiency, and advancing sustainable energy solutions in alignment with decarbonization goals.

08 HYDROGEN↗
DOE OSTI2023

A Scalable Compact Additively Manufactured Molten Salt to Supercritical Carbon Dioxide Heat Exchanger for Solar Thermal Application

Design of an additively manufactured molten salt (MS) to supercritical carbon dioxide (sCO 2 ) primary heat exchanger (PHE) for solar thermal power generation is presented. The PHE is designed to handle temperatures up to 720 °C on the MS side and an internal pressure of 200 bar on the sCO 2 side. In the core, MS flows through a three-dimensional periodic lattice network, while sCO 2 flows within pin arrays. The design includes integrated sCO 2 headers located within the MS flow, allowing for a counterflow design of the PHE. The sCO 2 headers are configured to enable uniform flow distribution into each sCO 2 plate while withstanding an internal pressure of 200 bar and minimizing obstruction to the flow of MS around it. The structural integrity of the design is verified on additively manufactured (AM) 316 stainless steel sub-scale specimens. An experimentally validated, correlation-based sectional PHE core thermofluidic model is developed to study the impact of flow and geometrical parameters on the PHE performance, with varied parameters including the mass flowrate, surface roughness, and PHE dimensions. A process-based cost model is used to determine the impact of parameter variation on build cost. The model results show that a heat exchanger with a power density of 18.6 MW/m 3 (including sCO 2 header volume) and effectiveness of 0.88 can be achieved at a heat capacity rate ratio of 0.8. As a result, the impact of design and AM machine parameters on the cost of the PHE are assessed.

14 SOLAR ENERGY↗
DOE OSTI2020

Catalytic converters having non-linear flow channels

Disclosed is a honeycomb catalyst substrate core having geometrically non-linear flow channels. In an embodiment, the honeycomb catalyst substrate core includes helical flow channels. In another embodiment, the honeycomb catalyst substrate core includes sinusoidal flow channels. In yet another embodiment, the honeycomb catalyst substrate core includes helical plus sinusoidal flow channels. The honeycomb catalyst substrate core comprises a plurality of parallel non-linear flow channels formed along a longitudinal axis of symmetry of the catalyst substrate core, each non-linear flow channel configured such that a turbulent vortical flow occurs during engine exhaust gas flow. Also disclosed is a method for manufacturing a ceramic honeycomb having non-linear flow channels, comprising the steps extrusion soft ceramic material through a die whilst the die moves through six degrees of freedom along its axis of symmetry. Disclosure includes a method for manufacturing a ceramic honeycomb having non-linear flow channels using three-dimensional printing.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Catalytic converters having non-linear flow channels

Disclosed is a honeycomb catalyst substrate core having geometrically non-linear flow channels. In an embodiment, the honeycomb catalyst substrate core includes helical flow channels. In another embodiment, the honeycomb catalyst substrate core includes sinusoidal flow channels. In yet another embodiment, the honeycomb catalyst substrate core includes helical plus sinusoidal flow channels. The honeycomb catalyst substrate core comprises a plurality of parallel non-linear flow channels formed along a longitudinal axis of symmetry of the catalyst substrate core, each non-linear flow channel configured such that eddies occurs during engine exhaust gas flow. Also disclosed is a method for manufacturing a ceramic honeycomb having non-linear flow channels, comprising the steps extrusion soft ceramic material through a die whilst the die moves through six degrees of freedom along its axis of symmetry. Disclosure includes a method for manufacturing a ceramic honeycomb having non-linear flow channels using three-dimensional printing.

Masoudi, Mansour↗
DOE OSTI2020

Direct numerical simulations of turbulent reacting flows with shock waves and stiff chemistry using many-core/GPU acceleration

Compressible reacting flows may display sharp spatial variation related to shocks, contact discontinuities or reactive zones embedded within relatively smooth regions. The presence of such phenomena emphasizes the relevance of shock-capturing schemes such as the weighted essentially non-oscillatory (WENO) scheme as an essential ingredient of the numerical solver. However, these schemes are complex and have more computational cost than the simple high-order compact or non-compact schemes. In this paper, we present the implementation of a seventh-order, minimally-dissipative mapped WENO (WENO7M) scheme in a newly developed direct numerical simulation (DNS) code called KAUST Adaptive Reactive Flows Solver (KARFS). In order to make efficient use of the computer resources and reduce the solution time, without compromising the resolution requirement, the WENO routines are accelerated via graphics processing unit (GPU) computation. The performance characteristics and scalability of the code are studied using different grid sizes and block decomposition. Furthermore, the performance portability of KARFS is demonstrated on a variety of architectures including NVIDIA Tesla P100 GPUs and NVIDIA Kepler K20X GPUs. In addition, the capability and potential of the newly implemented WENO7M scheme in KARFS to perform DNS of compressible flows is also demonstrated with model problems involving shocks, isotropic turbulence, detonations and flame propagation into a stratified mixture with complex chemical kinetics.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Impact of sub-core scale heterogeneity on CO2/brine multiphase flow for geological carbon storage in the Minnelusa sandstone

CO2 geological storage in deep saline aquifers is a mitigation option for CO2 emissions due to its large storage capacity and immediate accessibility. Accurately determining the CO2-brine relative permeability curves is key to the evaluation of CO2 injectivity and sweep efficiency in reservoir simulation as well as the CO2 injection in the field. This study highlights the remarkable effects of sub-core scale heterogeneity on the CO2-brine multiphase flow properties of the Minnelusa Sandstone in Wyoming. Two unsteady state CO2-brine drainage experiments were performed on the two samples. The first sample exhibits slanted laminated structure, while the second one represents a more homogeneous sandstone system. The CO2 saturation distributions during drainage reveals that the main variation in multiphase flow properties of two core samples were attributed to the porosity distribution that leads to the capillary pressure heterogeneity. Assisted history matching was used to obtain the respective relative permeability curves, which suggests heterogeneity-dependent behavior. In addition, sensitive and uncertainty analyses indicate that physical and petro-physical properties of low-porosity and low-permeability bedding layers exert marked effects on CO2 front breakthrough time and brine production. The results presented in this study help to gain insight into the CO2-brine multiphase flow properties in heterogeneous sandstones and can pave the way for the upscaling of CO2 migration and field-scale simulation accurately. This work is funded under the Department of Energy CarbonSAFE program (awards DE-FE0031624 DE0031891).

Kou, Zuhao↗
DOE OSTI2020

How eigenmode self-interaction affects zonal flows and convergence of tokamak core turbulence with toroidal system size

Self-interaction is the process by which a microinstability eigenmode that is extended along the direction parallel to the magnetic field interacts non-linearly with itself. This effect is particularly significant in gyrokinetic simulations accounting for kinetic passing electron dynamics and is known to generate stationary $E\times B$ zonal flow shear layers at radial locations near low-order mode rational surfaces (Weikl et al. Phys. Plasmas, vol. 25, 2018, 072305). Here, we find that self-interaction, in fact, plays a very significant role in also generating fluctuating zonal flows, which is critical to regulating turbulent transport throughout the radial extent. Unlike the usual picture of zonal flow drive in which microinstability eigenmodes coherently amplify the flow via modulational instabilities, the self-interaction drive of zonal flows from these eigenmodes are uncorrelated with each other. It is shown that the associated shearing rate of the fluctuating zonal flows therefore reduces as more toroidal modes are resolved in the simulation. In simulations accounting for the full toroidal domain, such an increase in the density of toroidal modes corresponds to an increase in the toroidal system size, leading to a finite system size effect that is distinct from the well-known profile shearing effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

A preconceptual design of an inverted Stable-Salt Reactor

This paper presents a preconceptual design of an inverted stable-salt reactor (SSR), with the unique feature that the static fuel salt is accommodated in one single bulk fuel container, while the coolant salt is circulating through the core via flow tubes penetrating the fuel container.The inverted SSR is expected to substantially decrease the capital cost compared to the state-of-the-art SSR such as the SSR-W designed by Moltex Energy, because one single gas vent at the top of the fuel container is required in the inverted SSR to prevent the leakage of the radioactive fission product gases instead of one gas vent in each of the hundreds of thousands of fuel tubes in SSR-W. In addition, the operation of the inverted SSR is largely simplified. However, numerous challenges associated with the design of the inverted SSR still remain to be overcome. Preliminary neutronics and thermal-hydraulics performance characteristics of the inverted SSR are assessed in this study. A viable core configuration of the inverted SSR is identified, and the superior characteristics of the inverted SSR, including a better neutron economy and a lower maximum fuel temperature, are demonstrated in this paper. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Understanding poromechanical response of a biogenic coalbed methane reservoir

Abstract Biogenic coalbed methane (BCBM) reservoirs aim to produce methane from in situ coal deposits following microbial conversion of coal. Success of BCBM reservoirs requires economic methane production within an acceptable timeframe. The work reported here quantifies the findings of previously published qualitative work, where it was found that bioconversion induces strains in the pore, matrix and bulk scales. Using imaging and dynamic strain monitoring techniques, the bioconversion induced strain is quantified here. To understand the effect of these strains from a reservoir geomechanics perspective, a corresponding poromechanical model is developed. Furthermore, findings of imaging experiments are validated using core-flooding flow experiments. Finally, expected field-scale behavior of the permeability response of a BCBM operation is modeled and analyzed. The results of the study indicated that, for Illinois coals, bioconversion induced strains result in a decrease in fracture porosity, resulting in a detrimental permeability drop in excess of 60% during bioconversion, which festers itself exponentially throughout its producing life. Results indicate that reservoirs with high initial permeability that will support higher Darcian flowrates, would be better suited for coal bioconversion, thereby providing a site-selection criteria for BCBM operations.

Pandey, Rohit (ORCID:0009000415483436)↗
DOE OSTI2024

Improving the modeling of near-wall interphase heat transfer in porous media models of Pebble Bed Reactors

Here, this work aims to improve capabilities for modeling localized effects in porous media models of Pebble Bed Reactors. The wall-channeling effect is the primary local phenomenon of interest in a PBR, where the presence of the reflector wall disrupts the pebble packing, causing the pebbles near the wall to pack less efficiently and creating large void regions. Accurate modeling of the near-wall region is important as it will affect core bypass flow and temperature predictions. Porous media models are commonly used for design scoping and plant-level simulations of PBRs. Although these models have some capabilities to model the near-wall region, the correlations that are available in porous media codes are often inaccurate when a multi-region model is used to discretize the near-wall region. This work employs a high-to-low analysis to study the accuracy of available interphase heat transfer closures. NekRS, a spectral element computational fluid dynamics code, is used to perform Large Eddy Simulations. These LES simulation results are compared to porous media model results from the Pronghorn porous media code. The friction term of the KTA drag closure is first improved, reducing the error in the prediction of the near-wall velocity from over 50% to less than 5%. This is combined with improvements to the form term from previous works to produce a drag closure that is capable of accurately modeling the wall-channeling effect across a variety of flow conditions. The Nusselt number predictions of several heat transfer correlations are compared to the high-fidelity results where it is found that the KTA heat transfer correlation is capable of accurately predicting the local Nusselt numbers that were determined in the high-fidelity simulation. Comparison of the radial solid temperature profiles, however, reveal discrepancies between NekRS and Pronghorn. It is discovered that the implementation of the interphase heat transfer coefficient that exists in many current porous media codes is not valid when local porosities are modeled. Instead, it is suggested that the interphase heat transfer coefficient should be dependent on the local porosity, the Nusselt number, and the local solid surface-to-volume ratio. Implementation of this change produces improvement in the agreement between the results obtained by NekRS and Pronghorn while using the KTA heat transfer correlation.

interphase heat transfer↗
DOE OSTI2023

Elements of H-mode pedestal structure

Abstract This paper reviews current understanding of key physics elements that control the H-mode pedestal structure, which exists at the boundary of magnetically confined plasmas. The structure of interest is the width, height and gradient of temperature, density and pressure profiles in the pedestal. Emphasis is placed on understanding obtained from combined experimental, theoretical and simulation work and on results observed on multiple machines. Pedestal profiles are determined by the self-consistent interaction of sources, transport and magnetohydrodynamic limits. The heat source is primarily from heat deposited in the core and flowing to the pedestal. This source is computed from modeling of experimental data and is generally well understood. Neutrals at the periphery of the plasma provide the dominant particle source in current machines. This source has a complex spatial structure, is very difficult to measure and is poorly understood. For typical H-mode operation, the achievable pedestal pressure is limited by repetitive, transient magnetohydrodynamic instabilities. First principles models of peeling–ballooning modes are generally able to explain the observed limits. In some regimes, instability occurs below the predicted limits and these remain unexplained. Several mechanisms have been identified as plausible sources of heat transport. These include neoclassical processes for ion heat transport and several turbulent processes, driven by the steep pedestal gradients, as sources of electron and ion heat transport. Reduced models have successfully predicted the pedestal or density at the pedestal top. Firming up understanding of heat and particle transport remains a primary challenge for developing more complete predictive pedestal models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

DC-Saturated Continuously Variable Series Reactors (CVSRs) for Power Flow Control in Power Transmission Systems

This paper proposes a novel continuously variable series reactor (CVSR) based on a dc current controller (DCC) to manage power flow in transmission systems. There are three major contributions. First, the three-dimensional electromagnetic interaction has been comprehensively analyzed to extend the understanding beyond the conventional 2D relationship. Second, a high-fidelity reluctance model of the CVSR with an improved DCC model is proposed and implemented. To overcome the fundamental concern for the system modeling, the DCC has been modeled as an ideal current source in parallel with an output impedance. Additionally, the induced back-EMF can be precisely projected which provides critical design guidelines for the DCC. Third, inspired by the theoretical analysis and modeling, a reliable high power DCC converter is designed accordingly to interface with kV-level back-EMF and supply kA-level dc current for a 115 kV/1500 A CVSR. Experiments are conducted in a practical transmission demonstration system. When the ac current in the transmission system varies from zero to 1500 A, experimental results show that the proposed CVSR can continuously regulate the reactance from 1.6 Ω to 5 Ω, validating the effectiveness of the proposed system design and modeling methodology.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Dependence of Dust Formation on the Supernova Explosion and nuDust

Dust is ubiquitous in the interstellar medium, serving as both a source of information and headaches to astronomers, depending on who you ask. The out-flows of core collapse supernovae (CCSNe) serve as a factory for dust nucleation and are one of a few known sources of dust in the universe. From observations of local CCSNe such as 1987A and Cassiopeia A, we know that dust is abundant in CCSN ejecta prior to interacting with the ISM. Furthermore, the explosion energy, explosive engine, metallicity, and progenitor mass of the CCSN will all impact the subsequent dust formation history and composition. Observations of the supernova ejecta probe the detailed composition of the ejecta which, in turn, can be used probe the properties of the progenitor star and the process of the explosion

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Research and Development of a Ventilation-Integrated Comfort System

From an indoor air quality perspective, the best residential ventilation strategies include filtering outdoor air and distributing that air to all occupied parts of a home. From an energy standpoint, it is desirable that energy be transferred from the exhaust air to the incoming outdoor air to limit heating and cooling impacts. Heat or energy recovery ventilators (HRVs or ERVs) can provide these functions, but researchers have seen many poor installations related to design, installation, and operation and maintenance. More robust ventilation systems may involve an ERV with a dedicated duct distribution system and controls. Such a duct system can be costly to install, and many builders reduce these costs by connecting an ERV to a central heating and cooling duct system. Although this can sometimes be done effectively, researchers have seen consistent challenges with low, inconsistent, or imbalanced flow rates; high electricity consumption; and—of greatest concern—outdoor air short-circuiting or not being delivered to occupied spaces at all. Most ERVs are designed to operate with their own duct system; they are not designed as an add-on to much larger heating, ventilating, and air-conditioning (HVAC) systems. The ventilation-integrated comfort system (VICS) is expressly designed to integrate with low-capacity, efficient, ducted heating and cooling systems. Overall, the latest VICS prototype consumed 40–75 watts (W), including the air handler power, to deliver 50–120 cfm of whole-dwelling ventilation. The large, cross-flow ERV core performed to match manufacturer values (73% winter sensible effectiveness, 64% summer total effectiveness), but further improvements are possible. The VICS system researched and tested during this project will provide efficient, controllable, balanced energy recovery ventilation that is integrated with heating and cooling systems. The integration reduces space and ductwork needed for separate ventilation systems, and there are no compromises to heating, cooling, or ventilation performance. The integrated nature of the device also reduces risks for improper installation and commissioning. Even when using the air handler blower to distribute outdoor air, the total power consumption is lower than that of most available ERV products in the same airflow range. This system has the potential to offer very high-performance ventilation with much smoother and simpler installation than conventional systems.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Developing an Ultra-Compact, Topology-Optimized Heat Exchanger using Additive Manufacturing

Traditional heat exchanger designs have relied on a plate-fin architecture, assembled in a crossflow configuration. These HX designs are limited in their maximum allowable temperature and, therefore, efficiency. More advanced designs, such as those containing counter-flow, microtube cores, can yield higher efficiencies, but generally require complex headers. The design of such headers is usually determined based on user experience rather than on rigorous design tools, which can lead to lossy architectures; conventional headers can generate up to 50% of the total pressure loss through the HX. Furthermore, the consequences of manufacturing techniques are rarely considered during the design phase. Our team has developed an ultra-compact, topology-optimized heat exchanger capable of operating in environments with temperatures and pressures up to 800°C (1472°F) and 250 bar (3626 psi), respectively. Throughout the program, the team leveraged extensive additive manufacturing research and experience in supercritical carbon dioxide (sCO 2 ) power generation experience to develop and commercialize the technology. The final power density numbers for the subscale and full-scale heat exchangers are >15 kW/kg and >50 kW/L, which includes the core and the headers. The team has involved the RTX business units, notably Collins Aerospace, in discussions for commercializing the technology.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2025

Summary Report Of The FY25 Computational Fluid Dynamics Verification And Validation Exercises In The Advanced Reactor Technologies - Gas-cooled Reactor Program

Verification and Validation (V&V) of numerical tools is critical for ensuring reasonable predictions during design, safety analysis, and licensing. Recent work in the Advanced Reactor Technologies - Gas-cooled Reactor (ART-GCR) program has focused on V&V of common Computational Fluid Dynamics (CFD) tools that are used within the Untied States. This report presents an update on these CFD V&V activities. These Generation IV Forum (GIF) Very High Temperature Reactor (VHTR) Computational Methods, Validation, and Benchmarking (CMVB) is an international organization dedicated to the verification and validation of High Temperature Gas-Cooled Reactor (HTGR) simulation tools. Participation in the CMVB provides additional value to the V&V activities, as it allows for access to a wider range of data, and provides valuable benchmarking exercises. Three HTGR phenomena are targeted: Reactor Cavity Cooling System (RCCS) performance, core bypass flow, and lower plenum mixing. Simulations of the University of Wisconsin-Madison (UW-Madison) RCCS facilities are performed with Reynolds Averaged Navier-Stokes (RANS) in StarCCM+. Results are compared for both forced and natural convection conditions, with both exhibiting good agreement with experimental measurements. The Idaho National Laboratory (INL) matched index of refraction (MIR) and Korean Atomic Energy Research Institute (KAERI) bypass flow expeirments are used to validation CFD predictions of bypass flow. Simulations are performed with RANS in StarCCM+ and with Large Eddy Simulation (LES) in NekRS. Finally, preliminary simulations of the Institute of Nuclear and New Energy Technology (INET) lower plenum mixing facilities are presented. Initial work has developed models with LES, RANS, and porous media models. These preliminary models are presented and compared to each other to gauge differences in predictions with each of the three methods.

and Benchmarking (CMVB)↗
DOE OSTI2022

Analysis of Postulated Accident Scenarios for the Transformational Challenge Reactor

The Transformational Challenge Reactor (TCR) is a helium-cooled, yttrium-hydride-moderated reactor that was designed for the U.S. Department of Energy Office of Nuclear Energy. A key objective of the TCR was to employ advanced manufacturing techniques in a nuclear system and demonstrate their potential for revolutionizing the nuclear reactor design process. One purpose of the present work is to demonstrate the safety of the TCR under postulated accidents. Based on RELAP5-3D and COMSOL analyses, the TCR remained below all current safety limits and far below the expected failure limits for the core materials. Another purpose of this work is to provide useful insights and recommendations regarding the application of RELAP5-3D to gas-cooled or other advanced reactors. A novel approach was implemented for simultaneously modeling conduction and radiation in RELAP5-3D, which was found to provide reasonable predictions of radial core, vessel, and ex-vessel heat transfer during postulated events. A multicode approach was also applied, in which high-fidelity COMSOL calculations were used to tune the radial heat transfer parameters in RELAP5-3D. The tuned RELAP5-3D model demonstrated comparable peak temperature predictions as COMSOL, despite a coarse treatment of the core in RELAP5-3D consisting of only two lumped heat structures. This high-fidelity tuning approach enabled enhanced accuracy as well as minimal complexity within the RELAP5-3D model, even for complex fuel geometric designs as in the TCR. Finally, investigations were made into the potential for flow reversal during a pressurized loss-of-forced-flow event in the TCR. The TCR is designed with downward helium flow through the core during normal operation. The RELAP5-3D model predicted that this downward flow would persist, without flow reversal, up to several days after the circulator trip. This was attributed to natural circulation hysteresis effects as have been noted in similar thermofluidic systems. Although flow stagnation and eventual reversal did not lead to unsafe TCR conditions, interesting spatial effects were observed which may have safety relevance for other reactor system designs and coolant types that are designed for downward core flow during normal operation, warranting closer investigation of the flow reversal phenomenon.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Ultralow platinum loading for redox-flow battery by electrospinning the electrocatalyst and the ionomer in core-shell fibers

Hydrogen Bromine Redox Flow Batteries (HBRFB) are promising candidates for large scale energy storage, having an excellent balance of system, inexpensive and abundant electrolytes, high power density and near zero kinetic limitations. However, they suffer from corrosion of the hydrogen electrode due to bromine species crossover, which requires a high loading of precious group metal (PGM) electrocatalyst. Herein, a standard catalyst has been used in an electrospun (ES) fiber mat electrode, allowing for a significant (six-fold) reduction in platinum loading from 0.3 mg Pt /cm 2 down to 0.05 mg Pt /cm 2 . At this very low loading, the electrospun electrode attained an impressive specific power of 11.5W/mg Pt , and exhibited excellent durability, with constant power output for 140 charge/discharge cycles. Further, the excellent performance of the electrospun hydrogen electrode is attribute to its unique core-shell nanofiber structure, which improves the stability of the catalyst by preventing bromide species from reaching the catalyst surface.

25 ENERGY STORAGE↗