Search NASA⌕ Search

SEARCH · Search NASA

Results for “COY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Fatigue life analysis for traction drives with application to a toroidal type geometry

A contact fatigue life analysis for traction drives was developed which was based on a modified Lundberg-Palmgren theory. The analysis was used to predict life for a cone-roller toroidal traction drive. A 90-percent probability of survival was assumed for the calculated life. Parametric results were presented for life and Hertz contact stress as a function of load, drive ratio, and size. A design study was also performed. The results were compared to previously published work for the dual cavity toroidal drive as applied to a typical compact passenger vehicle drive train. For a representative duty cycle condition wherein the engine delivers 29 horsepower at 2000 rpm with the vehicle moving at 48.3 km/hr (30 mph) the drive life was calculated to be 19,200 km (11 900 miles).

Coy, J. J.↗
NASA NTRS1977

Life analysis of restored and refurbished bearings

An analysis of the potential life of refurbished and restored bearings was performed. The sensitivity of 10-percent life and mean-time-between-failure to the effects of cumulative fatigue damage and the amount of stressed volume removed in the restoration process were examined. A modified Lundberg-Palmgren theory was used to predict that the expected 10-percent life of a restored bearing, which is dependent on the previous service time and the volume of material removed from the race surfaces, can be between 74 and 100 percent of the new bearing life. Using renewal theory, it is found that the mean time between failure ranged from 90 to 100 percent of that for a new bearing.

Coy, J. J.↗
NASA NTRS1977

Experimental and Analytical Load-Life Relation for AISI 9310 Steel Spur Gears

Life tests were conducted at three different loads with three groups of 8.9 cm pitch diameter spur gears made of vacuum arc remelted VAR AISI 9310 steel. Life was found to vary inversely with load to the 4.3 and 5.1 power at the L10 sub and L50 sub life levels, respectively. The Weibull slope varied linearly with maximum Hertz contact stress, having an average value of 2.5. The test data when compared to AGMA standards showed a steeper slope for the load-life diagram.

Townsend, D. P.↗
NASA NTRS1978

Statistical model for asperity-contact time fraction in elastohydrodynamic lubrication

Relations for the asperity contact time fraction during elastohydrodynamic (EHD) lubrication of a typical ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces were used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately 4 to 5. This thickness ratio is several times larger than reported in the literature where one-dimensional random surface models were used.

Sidik, S. M.↗
NASA NTRS1977

Experimental and analytical load-life relation for AISI 9310 steel spur gears

Life tests were conducted at three different loads with three groups of 8.9 cm, pitch diameter spur gears made of vacuum arc remelted AISI 9310 steel. Life was found to vary inversely with load to the 4.3 and 5.1 power at the L-10 and L-50 life levels, respectively. The Weibull slope varied linearly with maximum Hertz contact stress, having an average value of 2.5. The test data when compared to AGMA standards showed a steeper slope for the load-life diagram.

Townsend, D. P.↗
NASA NTRS1979

Two-dimensional random surface model for asperity-contact in elastohydrodynamic lubrication

Relations for the asperity-contact time function during elastohydrodynamic lubrication of a ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces are used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately four to five. This thickness ratio is several times large than reported in the literature where one-dimensional random surface models were used. It is shown that low pass filtering of the statistical records will bring agreement between the present results and those in the literature.

Coy, J. J.↗
NASA NTRS1979

Comparison of predicted and measured elastohydrodynamic film thickness in a 20-millimeter-bore ball bearing

Elastohydrodynamic film thicknesses were measured for a 20-mm bore ball bearing using the capacitance technique. The bearing was thrust loaded to 90, 445, and 778 N (20, 100, and 175 lb). The corresponding maximum contact stress on the inner race was 1.28, 2.09, and 2.45 GPa (185 000, 303,000, and 356, 000 psi). Test speeds ranged from 400 to 15,000 rpm. Measurements were taken with four different lubricants: (1) synthetic paraffinic; (2) synthetic paraffinic with additives; (3) synthetic type II aircraft oil; and (4) synthetic cycloaliphatic hydrocarbon traction fluid. The test bearing was mist lubricated. Test temperatures were 27, 65, and 121 C (80, 150, and 250 F). The measured results for the various test parameters were compared to theoretical predictions from computer programs. Also the data were plotted on dimensionless coordinates and compared to several classical isothermal theories.

Coy, J. J.↗
NASA NTRS1979

Correlation of asperity contact-time fraction with elastohydrodynamic film thickness in a 20-millimeter-bore ball bearing

Elastohydrodynamic film thicknesses and asperity contact-time fractions were measured for a 20 mm bore ball bearing by using the capacitance and conductance techniques. The bearing was thrust loaded to 90, 445, and 778 N. The corresponding maximum stresses on the inner race were 1.28, 2.09, and 2.45 GPa. The test speed ranged from 400 to 15,000 rpm. The test bearing was mist lubricated with a MIL-L-23699A turbine oil. The temperature was 27 C. The experimental results were correlated to give the percent film (no-contact-time fraction) as a function of measured film thickness. Measurements were made for three test series that represented the test bearing in various conditions of run-in. The measurements show that the percent film changes with bearing run-in time. The experimental results agreed well with theoretical predictions based on surface trace analysis for a new bearing. For the run-in state, they agreed with previously reported experimental results. The results show that asperity contact existed at a film thickness-roughness ratio lambda of 6.0 or less for a new bearing. After run-in, no asperity contact occurred at a lambda of 3.5 or greater.

Coy, J. J.↗
NASA NTRS1979

NASA gear research and its probable effect on rotorcraft transmission design

The results of the NASA gear research is reviewed as well as those programs which are presently being undertaken. Research programs studying pitting fatigue, gear steels and processing, life prediction methods, gear design and dynamics, elastohydrodynamic lubrication, lubrication methods and gear noise are presented. The impact of advanced gear research technology on rotorcraft transmission design is discussed.

Zaretsky, E. V.↗
NASA NTRS1979

An unusually large westerly amplitude of the quasi-biennial oscillation

A time-height section of the quasi-biennial oscillation is presented for the period 1950-1978. The data are from the Canal Zone station through June 1970 and from Kwajalein from July 1970 through April 1978 (both stations are near 9 deg N). The most striking feature in the new data is the unusually strong westerly phase which occurred in the winter of 1977-1978. The magnitude of the westerly amplitude in December 1978 was over 60 m/sec at and above 10 mb. The easterly phase below the westerly phase of the 1977-1978 winter was also unusually large. The other features in the new data are consistent with past observations.

Coy, L.↗
NASA NTRS1979

Two-dimensional random surface model for asperity-contact in elastohydrodynamic lubrication

Relations for the asperity-contact time fraction during elastohydrodynamic lubrication of a ball bearing are presented. The analysis is based on a two-dimensional random surface model, and actual profile traces of the bearing surfaces are used as statistical sample records. The results of the analysis show that transition from 90 percent contact to 1 percent contact occurs within a dimensionless film thickness range of approximately four to five. This thickness ratio is several times larger than reported in the literature where one-dimensional random surface models were used. It is shown that low pass filtering of the statistical records will bring agreement between the present results and those in the literature.

Coy, J. J.↗
NASA NTRS1979

A possible 2-day oscillation near the tropical stratopause

An examination of daily meteorological rocket data taken during January and February 1977 at Kwajalein, Marshall Islands (9 deg N, 168 deg E) suggests the presence of a large oscillation in the meridional wind with a period near 2 days. Some rocket data taken concurrently at other stations is also presented. The Canal Zone station (9 deg N, 80 deg W) suggests a possible 2-day oscillation, while middle- and high-latitude stations show variability with periods ranging from 2-5 days.

Coy, L.↗
NASA NTRS1979

Mechanical components

Research on bearings, gears, seals, and rotor dynamics (specifically high speed balancing and dampers) is presented. The research pertains to problems in both aircraft turbine engines and helicopter transmissions.

Anderson, W. J.↗
NASA NTRS1980

Simplified fatigue life analysis for traction drive contacts

A simplified fatigue life analysis for traction drive contacts of arbitrary geometry is presented. The analysis is based on the Lundberg-Palmgren theory used for rolling-element bearings. The effects of torque, element size, speed, contact ellipse ratio, and the influence of traction coefficient are shown. The analysis shows that within the limits of the available traction coefficient, traction contacts exhibit longest life at high speeds. Multiple, load-sharing roller arrangements have an advantageous effect on system life, torque capacity, power-to-weight ratio and size.

Rohn, D. A.↗
NASA NTRS1980

Some limitations in applying classical EHD film-thickness formulae to a high-speed bearing

Elastohydrodynamic film thickness was measured for a 20 mm ball bearing using the capacitance technique. The bearing was thrust loaded to 90, 448, and 778 N. The corresponding maximum stresses on the inner race were 1.28, 2.09, and 2.45 GPa. Test speeds ranged from 400 to 14,000 rpm. Film thickness measurements were taken with four different lubricants: (1) synthetic paraffinic; (2) synthetic paraffinic with additives; (3) neopentylpolyol (tetra) ester; and (4) synthetic cycloaliphatic hydrocarbon traction fluid. The test bearing was mist lubricated. Test temperatures were 300, 338, and 393 K. The measured results were compared to theoretical predictions and are presented.

Coy, J. J.↗
NASA NTRS1980

Ideal spiral bevel gears: A new approach to surface geometry

The fundamental geometrical characteristics of spiral bevel gear tooth surfaces are discussed. The parametric representation of an ideal spiral bevel tooth is developed based on the elements of involute geometry, differential geometry, and fundamental gearing kinematics. A foundation is provided for the study of nonideal gears and the effects of deviations from ideal geometry on the contact stresses, lubrication, wear, fatigue life, and gearing kinematics.

Huston, R. L.↗
NASA NTRS1979

NASA gear research and its probable effect on rotorcraft transmission design

The NASA Lewis Research Center devised a comprehensive gear technology research program beginning in 1969, the results of which are being integrated into the NASA civilian Helicopter Transmission System Technology Program. Attention is given to the results of this gear research and those programs which are presently being undertaken. In addition, research programs studying pitting fatigue, gear steels and processing, life prediction methods, gear design and dynamics, elastohydrodynamic lubrication, lubrication methods and gear noise are presented. Finally, the impact of advanced gear research technology on rotorcraft transmission design is discussed.

Zaretsky, E. V.↗
NASA NTRS1980

Constrained fatigue life optimization of a NASVYTIS multiroller traction drive

A contact fatigue life analysis method for multiroller traction drives is presented. The method is based on the Lundberg-Palmgren analysis method for rolling element bearing life prediction, and also uses life adjustment factors for materials, processing, lubrication, and effect of traction. The analysis method is applied in an optimization study to the multiroller traction drive, consisting of a single-stage planetary configuration with two rows of stepped planet rollers of five rollers per row. The drive was approximately 25 centimeters in diameter by 11 centimeters long, having a nominal ratio of 15:1. The theoretically predicted drive life was 2510 hours at a nominal continuous power and speed of 74.6 kW (100 hp) and 75,000 rpm.

Coy, J. J.↗