Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbon nanomaterials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Using Holey Graphene for Improved Interfacial Contact in Solid Electrolyte Ionic Conductivity Measurements

Solid-state batteries (SSBs) are poised to become the batteries of the future with advantages such as higher energy density, lighter weight, versatile geometry, and greater safety due to low flammability risk. An important parameter of the solid electrolyte (SE) used is its ionic conductivity. The ionic conductivity is generally calculated from the bulk resistance of a SE pellet, measured from the electrochemical impedance spectroscopy data. The SE pellet is typically prepared from the electrolyte powder by dry compression and is sandwiched between two blocking current collectors to obtain the impedance spectroscopy data. One of the challenges in conducting this measurement is poor interfacial contacts between the SE pellet and the current collector surfaces. Therefore, measurements reported in the literature may underestimate the true ionic conductivity of a given electrolyte. Holey graphene is a carbon nanomaterial with high electrical conductivity and unique dry compressibility, which is unusual for carbon materials but similar to many oxide and sulfide SEs. In this work, it is demonstrated that adding a thin layer of holey graphene between the electrolyte and the stainless steel current collectors significantly improves the interfacial contact. The ionic conductivity values obtained in the effort were sometimes several times higher than the data measured for SEs without the holey graphene layers. This work calls for more standardized measurement procedures to reduce the discrepancies in reported ionic conductivity values.

Solid state battery↗
DOE OSTI2021

Catalytic decomposition of methane into hydrogen and high-value carbons: combined experimental and DFT computational study

Thermocatalytic decomposition (TCD) of methane can produce hydrogen and valuable nanocarbon co-products with low to near-zero CO2 emission. In this study, a series of Pd promoted Ni catalysts, prepared with various Ni/Pd ratios on a CNT support, were evaluated for methane TCD performance. Characterization and calculations using density functional theory (DFT) were carried out to elucidate the activity–structure relationship and growth mechanism of carbon nanomaterials. It was found that the methane conversion and stability of the catalysts were highly dependent on the Ni/Pd ratio and reaction temperature. DFT calculations revealed that the diffusion of carbon in the metal sublayer required for CNT growth was more favorable in the Ni–Pd alloy lattice suggesting that the buildup of carbon in the metal alloy sublayer facilitated the formation of CNTs and CNFs. A cyclic reaction–regeneration process for self-sustained TCD was experimentally demonstrated. In each cycle, a portion of the separated CNT product was used to re-synthesize the Ni–Pd/CNT catalyst for use in the next reaction cycle. After five cycles of operation, the CH4 conversion, morphology and crystallinity of the carbon product remained unchanged.

Wang, I-Wen↗
DOE OSTI2026

Circumventing thermodynamic limitations in converting carbon dioxide into carbon nanotubes via tandem catalysis

Carbon nanotubes (CNTs) are important materials for electronics and structural composites, but their production still relies on hydrocarbon-based chemical vapor deposition, an energy-intensive and fossil-dependent process, limited by rapid catalyst deactivation. Using CO2 as a carbon feedstock offers a sustainable route for CNT synthesis, yet direct CO2 conversion to CNTs is thermodynamically unfavorable and existing CO2-to-carbon pathways mainly yield amorphous or weakly graphitized solids. Here, we demonstrate a tandem electrochemical–thermochemical (EC-TC) strategy that overcomes these limitations. CO2 is first electrochemically reduced to a tunable mixture of C2H4 and CO, which is directly fed into a thermochemical reactor and converted into CNTs with controllable morphology and high CNT-to-metal mass ratios (~200) over NiFe catalysts at 750 °C. In situ synchrotron-based characterization and density functional theory calculations reveal that CO dissociation and C2H4 decomposition on NiFe alloys cooperatively promote CNT nucleation and sustained growth. This EC-TC strategy establishes a modular route for converting CO2 into value-added carbon nanomaterials.

03 NATURAL GAS↗
DOE OSTI2021

Connection between the physicochemical characteristics of amorphous carbon thin films and their electrochemical properties

Connecting a material's surface chemistry with its electrocatalytic performance is one of the major questions in analytical electrochemistry. This is especially important in many sensor applications where analytes from complex media need to be measured. Unfortunately, today this connection is still largely missing except perhaps for the most simple ideal model systems. Here we present an approach that can be used to obtain insights about this missing connection and apply it to the case of carbon nanomaterials. In this paper we show that by combining advanced computational techniques augmented by machine learning methods with x-ray absorption spectroscopy (XAS) and electrochemical measurements, it is possible to obtain a deeper understanding of the correlation between local surface chemistry and electrochemical performance. As a test case we show how by computationally assessing the growth of amorphous carbon (a-C) thin films at the atomic level, we can create computational structural motifs that may in turn be used to deconvolute the XAS data from the real samples resulting in local chemical information. Then, by carrying out electrochemical measurements on the same samples from which x-ray spectra were measured and that were further characterized computationally, it is possible to gain insight into the interplay between the local surface chemistry and electrochemical performance. To demonstrate this methodology, we proceed as follows: after assessing the basic electrochemical properties of a-C films, we investigate the effect of short HNO 3 treatment on the sensitivity of these electrodes towards an inner sphere redox probe dopamine to gain knowledge about the influence of altered surface chemistry to observed electrochemical performance. Overall, these results pave the way towards a more general assessment of electrocatalysis in different systems and provide the first steps towards data driven tailoring of electrode surfaces to gain optimal performance in a given application.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

A universal method to fabricating porous carbon for Li-O 2 battery

The main bottleneck in the application of biomass-based carbon material in energy field is the development of an economical, nanoscale controllable and universal fabrication method. Herein, we demonstrate that a biomass-derived carbon consisting of loose carbon nanosphere clusters could serve as an ideal cathode material for high performance Li-O 2 batteries. The carbon nanomaterial can be prepared from both biomass derivatives and crude biomass by a low cost, facile and nanoscale controllable method. The open slit-shaped hierarchical pore structure endows the electrode sufficient active surface sites and mass transport channels that are not easily asphyxiated by the discharge products. The concentration of oxygenic groups and structure defects on the surface of obtained carbon materials is very low, which minimizes the side reactions associated with carbon decomposition. Finally, the unique pore structure and surface properties of the carbon electrode give rise to a superhigh specific capacity of 20,300 mA h g -1 and an extremely long cycle life which a cyclic capacity retention of 100% is maintained for 543 cycles with current density of 0.2 mA cm -2 at controlled discharge-charge depths of 500 mA h g -1 .

25 ENERGY STORAGE↗
DOE OSTI2020

Analytical model of low and high ablation regimes in carbon arcs

Graphite ablation by an electric arc or a laser/solar flux is widely used for the synthesis of carbon nanomaterials. Previously, it was observed in multiple arc experiments that the ablation rate is a strong nonlinear function of the arc current and it drastically increases at some threshold current. As such, we developed an analytical model explaining this transition in the rate of ablation by an electric arc or a laser/solar flux. The model not only explains the observations but can also accurately predict the experimentally observed ablation rates. The model takes into account redeposition of carbon back to the ablated surface, which is the key process responsible for the observed effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

From atomistic models to machine learning: Predictive design of nanocarbons under extreme conditions

The formation of technologically valuable nanocarbon structures under extreme conditions, such as those produced during high-explosive detonations, remains poorly understood but holds significant potential for the development of controlled synthesis pathways. While detonation shockwaves provide the high-pressure, high-temperature environment required for nanodiamond formation, subsequent cooling and decompression dictate whether the diamond phase is preserved or transformed into other nanocarbon structures. Here, in this study, we employ GPU-accelerated reactive molecular dynamics (ReaxFF) simulations to investigate the graphitization and structural remodeling of detonation nanodiamond under nonlinear quench and pressure-release trajectories. We further investigate how the initial nanodiamond morphology; cuboctahedral, octahedral, or hexagonal prism influences the resulting transformation products. Evolution of nanostructure, allotrope (via simulated x-ray diffraction), carbon hybridization, and ring statistics are tracked during a two-stage quench from 5000 K to 60 GPa. Rapid cooling combined with slow decompression optimizes cubic diamond retention, whereas slow cooling with rapid pressure release promotes surface-to-core graphitization, producing concentric sp 2 -hybridized layers and hollowed inner shells. Octahedral nanodiamonds evolve into carbon nano-onions, initially forming bucky diamonds that progressively transform into fully sp 2 -hybridized structures, while hexagonal prisms preferentially form parallel-stacked graphite layers resembling carbon dots. Transient hexagonal diamond (lonsdaleite) emerges as an interfacial phase, suggesting potential reversibility in the shock-induced graphite-to-diamond transformation pathway transformation route. To extend predictive capabilities, we trained machine learning (ML) regressors on over 10 5 node-hours of molecular dynamics (MD) trajectories. A multilayer perceptron (MLP) model reliably predicts the number of graphitized layers from temperature–pressure trajectories with a coefficient of determination (R 2 ) exceeding 0.90. This high predictive fidelity enables efficient, high-throughput mapping of the synthesis parameter space for optimized graphitization outcomes. Collectively, morphological control combined with optimized quench–decompression conditions promote the selective synthesis of nanocarbon allotropes. This work establishes a data-driven framework for the rational, a priori design of carbon nanomaterials for applications in energy storage, sensing, and biomedicine.

Detonation nanodiamond remodeling↗
DOE OSTI2021

Flash graphene from rubber waste

Most conventional production processes for graphene are time-consuming, solvent-intensive, and energetically demanding. To circumvent these limitations for mass production, flash Joule heating (FJH) has been shown to be an effective method to synthesize graphene. Here, methods for optimizing production of graphene from rubber waste feedstocks are shown. Through careful control of system parameters, such as pulse voltage and pulse time, turbostratic flash graphene (tFG) can be produced from rubber waste. It is characterized by Raman spectroscopy, X-ray diffraction and thermogravimetric analysis. Here, the resulting tFG can be easily exfoliated and dispersed into various solvents because of its turbostratic arrangement. Addition of tFG into Portland cement results in a significant increase in the compressive strength of the composite. From a materials perspective, FJH offers a facile and inexpensive method for producing high quality tFG from rubber waste materials, which would otherwise be disposed of in landfills or burned for fuel. FJH allows for upcycling of low-value rubber waste into high-value carbon nanomaterials for use as reinforcing additives.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Waste plastic- and coke-derived flash graphene as lubricant additives

Lubricants play an essential role in reducing wear in mechanical systems. Carbon nanomaterial additives, such as graphene, have been found to significantly improve tribological performance when used as lubricant additives. Here, in this study, post-consumer plastic and metallurgical coke are converted into turbostratic flash graphene (FG) through flash Joule heating (FJH). The FG is then added to either poly(alpha olefin) 6 or 9 (PAO 6 or PAO 9). Adding waste plastic-derived FG (WPFG) and metallurgical coke-derived FG (MCFG) to lubricants resulted in a significant decrease in the coefficient of friction (CoF), wear scar diameter (WSD), and roughness during four-ball testing. WPFG and MCFG decrease the CoF in PAO 9 by 6% and 9% at 0.1 mg mL -1 , respectively, and in PAO 6 by 23% and 6% at 0.5 mg mL -1 , respectively. WPFG and MCFG decrease the WSD of steel balls in PAO 9 by 14% and 8% at 0.5 mg mL -1 , respectively, and in PAO 6 by 12% and 14% at 0.5 mg mL -1 , respectively, by forming a coating-like layer between the metal surfaces. Roughness decreased by 38% and 32% for WPFG and MCFG in PAO 6, respectively, and by 35% and 29% for WPFG and MCFG in PAO 9, respectively. Finally, preliminary life cycle analyses demonstrate that production of FG produces up to 99% less greenhouse gas emissions, requires 98% less energy, and consumes 99.9% less water when compared to conventional production techniques of graphene. Hence, metallurgical coke and waste plastic are shown to be ready feedstocks for high-quality FG lubricant additives.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Dry-pressed lithium nickel cobalt manganese oxide (NCM) cathodes enabled by holey graphene host

There is an increasing demand for electric vehicle batteries with higher energy densities that can be manufactured with low cost utilizing environmentally friendly processes. Lithium nickel cobalt manganese oxides (NCM), such as LiNi(0.5)Co(0.2)Mr(0.3)O(2) (NCM523), are commonly used in commercial lithium ion batteries for electric vehicle applications. These cathodes are typically fabricated using environmentally hazardous, energy intensive, and time-consuming solvent-based slurry casting processes. Polymeric binders, also required for cathode preparation, add weight and can undergo parasitic reactions during battery cycling. Here we report a facile, solvent-free, binder-free, and rapid cold-press electrode fabrication process to prepare high mass loading NCM cathodes within minutes. This process is enabled by the use of holey graphene, a unique lightweight, compressible carbon nanomaterial that serves as both a binder and an electrically conductive matrix. NCM cathodes fabricated by this method are stable and exhibit good active material utilization. A significant advantage for the dry-press process is that the electrode mass loadings can be readily increased simply by adding more composite powder to the compression molding die, resulting in improved areal capacities that are attractive for applications requiring high energy per unit footprint. (C) 2020 Elsevier Ltd. All rights reserved.

25 ENERGY STORAGE↗
DOE OSTI2021

Composition and Structure of Fluorescent Graphene Quantum Dots Generated by Enzymatic Degradation of Graphene Oxide

The broad applications of carbon nanomaterials (CNMs) in both materials and life sciences necessitate investigation of their metabolites due to the inevitable contact of CNMs and biological systems. Graphene oxide (GO), along with other types of CNMs, can be enzymatically degraded by myeloperoxidase (MPO), an enzyme released during the innate immune response. However, the enzymatic degradation products are neither well-defined nor well-understood. Some products generated during MPO-catalyzed degradation of GO could emit blue photoluminescence (PL) and were simply dubbed graphene quantum dots (GQDs) without further elucidating their structures. In this work, we use liquid chromatography-mass spectrometry (LC-MS) to isolate and elucidate chemical structures of the MPO-catalyzed degradation products. A general chemical formula screening workflow was developed for the GQDs, which are in the form of polyaromatic hydrocarbons (PAHs), obtained in the degradation products. Structures of the PAHs responsible for the blue PL were further proposed using density functional theory (DFT) calculations. Our results indicated that structures with several conjugated benzene rings are likely to generate the observed PL. This work provides insights into the mechanism of enzymatic degradation and open opportunities for fluorescence imaging of GO in biological systems.

composition and structure screening↗
DOE OSTI2026

Reacting CO 2 with Light Alkanes to Value-Added Products

Catalytic conversion of anthropogenic carbon dioxide (CO 2 ) into value-added products is a promising strategy to mitigate global carbon emissions. Concurrently, the shale gas revolution has provided an abundant supply of light alkanes (methane, ethane, propane, and butane), presenting a unique opportunity to employ these underutilized hydrocarbons as an effective, low-cost hydrogen source for CO 2 reduction. In this Perspective, we summarize past efforts, current state, and future opportunities for reacting CO 2 with light alkanes to generate a diverse range of value-added products. Compared with direct alkane conversion, the introduction of CO 2 fundamentally alters reaction thermodynamics and kinetics, enabling selective C–H and C–C bond activation while suppressing catalyst deactivation from coke formation. Building on decades of research in dry reforming and CO 2 -assisted dehydrogenation, recent advances in catalyst design have enabled CO 2 -assisted dehydrogenation processes that approach chemical equilibrium for the selective production of olefins and syngas. Importantly, advances in catalyst design and reactor engineering have further expanded the product scope beyond gas-phase (syngas and olefins) to include liquid-phase (oxygenates and aromatics), and solid-phase products (carbon nanomaterials). We highlight key catalyst design principles for controlling reaction pathways and discuss major challenges and opportunities in developing selective and versatile platforms for the simultaneous upgrading of CO 2 and light alkanes.

CO2↗
NASA NTRSDate not supplied

Layered Electrode Architectures Enabled by Holey Graphene Hosts

Battery electrodes are typically prepared using a slurry-based method, where high boiling point organic solvents are typically used with a polymer binder to disperse active electrode materials and conductive carbon additives followed by casting into current collector sheets. In this process, the use of organic solvents are environmentally hazardous, energy intensive, and time-consuming, while polymeric binders add weight and can undergo parasitic reactions during battery cycling. Here we discuss the use of a unique conductive carbon nanomaterial, namely holey graphene, as a multifunctional host that can be processed via a facile, solvent-free, binder-free, cold pressing method to prepare electrodes with unique architectures. This approach can accommodate a broad range of battery chemistries, such as lithium oxygen/carbon dioxide (Li-O2/CO2), lithium sulfur/selenium (Li-S/Se), and various lithium ion chemistries. The successful use of dry, cold compression allows the convenient modification of electrode mass loading with unique architectures containing active materials randomly mixed or layered with single or multiple layers of one or more active materials. In the conventional slurry-based electrode fabrication method, it is difficult, if not impossible, to achieve such layered architectures. In particular, the layered electrode architectures from the dry, cold press approach are easy to fabricate without significantly sacrificing device performance, and are amenable to continuous roll-to-roll dry processing. In addition, these architectures offer unprecedented perspectives on the battery material loading vs. utilization efficiency, as well as enabling unique characterization opportunities to advance mechanistic understanding of various battery chemistries. Potential applications of this unique electrode fabrication approach for solid-state batteries will also be discussed.

holey graphene, batteries, electrode architecture,↗
DOE OSTI2021

Determination of positive anode sheath in anodic carbon arc for synthesis of nanomaterials

In the atmospheric pressure anodic carbon arc, ablation of the anode serves as a feedstock of carbon for production of nanomaterials. It is known that the ablation of the graphite anode in this arc can have two distinctive modes with low and high ablation rates. The transition between these modes is governed by the power deposition at the arc attachment to the anode and depends on the gap between the anode and the cathode electrodes. Probe measurements combined with optical emission spectroscopy are used to analyze the voltage drop between the arc electrodes. These measurements corroborated previous predictions of a positive anode sheath (i.e. electron attracting sheath) in this arc, which appears in both low and high ablation modes. However, the positive anode sheath was determined to be ~3–8 V, significantly larger than ~0.5 V predicted by previous models. Thus, there are apparently other physical mechanisms not considered by these models that force the anode sheath to be electron attracting in both ablation regimes. Another key result is a relatively low electron temperature (~0.6 eV) obtained from OES using a collisional radiative model. This result partially explains a higher arc voltage (~20 V) required to sustain the arc current of 50–70 A than predicted by existing simulations of this discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2013

Characterization of Plasma Synthesized Vertical Carbon Nanofibers for Nanoelectronics Applications

We report on the material characterization of carbon nanofibers (CNFs) which are assembled into a three-dimensional (3D) configuration for making new nanoelectromechanical systems (NEMS). High-resolution scanning electron microscopy (SEM) and x-ray electron dispersive spectroscopy (XEDS) are employed to decipher the morphology and chemical compositions of the CNFs at various locations along individual CNFs grown on silicon (Si) and refractory nitride (NbTiN) substrates, respectively. The measured characteristics suggest interesting properties of the CNF bodies and their capping catalyst nanoparticles, and growth mechanisms on the two substrates. Laser irradiation on the CNFs seems to cause thermal oxidation and melting of catalyst nanoparticles. The structural morphology and chemical compositions of the CNFs revealed in this study should aid in the applications of the CNFs to nanoelectronics and NEMS.

carbon nanomaterials↗
NASA NTRS2008

Novel Carbon Dioxide Microsensor Based on Tin Oxide Nanomaterial Doped With Copper Oxide

Carbon dioxide (CO2) is one of the major indicators of fire and therefore its measurement is very important for low-false-alarm fire detection and emissions monitoring. However, only a limited number of CO2 sensing materials exist due to the high chemical stability of CO2. In this work, a novel CO2 microsensor based on nanocrystalline tin oxide (SnO2) doped with copper oxide (CuO) has been successfully demonstrated. The CuO-SnO2 based CO2 microsensors are fabricated by means of microelectromechanical systems (MEMS) technology and sol-gel nanomaterial-synthesis processes. At a doping level of CuO: SnO2 = 1:8 (molar ratio), the resistance of the sensor has a linear response to CO2 concentrations for the range of 1 to 4 percent CO2 in air at 450 C. This approach has demonstrated the use of SnO2, typically used for the detection of reducing gases, in the detection of an oxidizing gas.

Xu, Jennifer C.↗
DOE OSTI2020

Facile diamond synthesis from lower diamondoids

Carbon-based nanomaterials have exceptional properties that make them attractive for a variety of technological applications. Here, we report on the use of diamondoids (diamond-like, saturated hydrocarbons) as promising precursors for laser-induced high-pressure, high-temperature diamond synthesis. The lowest pressure and temperature $(P-T)$ conditions that yielded diamond were 12 GPa (at ~2000 K) and 900 K (at ~20 GPa), respectively. This represents a substantially reduced transformation barrier compared with diamond synthesis from conventional (hydro)carbon allotropes, owing to the similarities in the structure and full sp 3 hybridization of diamondoids and bulk diamond. At 20 GPa, diamondoid-to-diamond conversion occurs rapidly within <19 μs. Molecular dynamics simulations indicate that once dehydrogenated, the remaining diamondoid carbon cages reconstruct themselves into diamond-like structures at high $P-T$. This study is the first successful mapping of the $P-T$ conditions and onset timing of the diamondoid-to-diamond conversion and elucidates the physical and chemical factors that facilitate diamond synthesis.

36 MATERIALS SCIENCE↗