Search NASA⌕ Search

SEARCH · Search NASA

Results for “Component Test Capability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

A 10,000 hour endurance test of a 700 series 30 cm engineering model thruster

This paper describes a 10,000 hour test of the first engineering model of the 30-cm ion thruster which is expected to form the basis of future prime propulsion systems. This test demonstrated the lifetime capability of such critical components as cathodes, vaporizers, isolators, and optics. The results of the test are described including the conclusions derived from an extensive post-test analysis of the thruster. This test did identify a major life limiting problem - discharge chamber erosion. The modifications which have been incorporated in the 900 series 30-cm ion thrusters to minimize this problem are described.

Collett, C. R.↗

Status of the RBCC Direct-Connect Mixer Combustor Experiment

The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.

Walker, James F.↗

Status of the RBCC Direct-Connect Mixer Combustor Experiment

The NASA Glenn Research Center is developing hydrogen based combined cycle propulsion technology for a single-stage-to-orbit launch vehicle application under a project called GTX. Rocket Based Combined Cycle (RBCC) propulsion systems incorporate one or more rocket engines into an airbreathing flow path to increase specific impulse as compared to an all rocket-powered vehicle. In support of this effort, an RBCC direct-connect test capability was established at the Engine Components Research Laboratory to investigate low speed, ejector ramjet, and initial ramjet operations and performance. The facility and test article enables the evaluation of two candidate low speed operating schemes; the simultaneous mixing and combustion (SMC) and independent ramjet stream (IRS). The SMC operating scheme is based on the fuel rich operations of the rocket where performance depends upon mixing between the rocket plume and airstream. In contrast, the IRS scheme fuels the airstream separately and uses the rocket plume to ignite the fuel-air mixture. This paper describes the test hardware and facility upgrades installed to support the RBCC tests. It also defines and discusses low speed technical challenges being addressed by the experiments. Finally, preliminary test results, including rocket risk mitigating tests, unfueled airflow tests, and the integrated system hot fire test will be presented.

Walker, James F.↗

Low loss, flexible, lightweight corporate RF feed system for SAR antenna application

Mechanical and electrical efficiency constraints imposed by the SEASAT-A synthetic aperture radar antenna posed difficult design problems. After consideration of available standard cable and waveguide systems, it was determined that an optimum design could be obtained from a suspended substrate RF feed system. Size and mechanical flexibility constraints forced the design of a flexible, suspended substrate section capable of 180-degree flexure. Original design goal for insertion loss over power division was 1 db; measured results indicated 0.6 db maximum across the band. Multipactor testing of system components indicated system breakdown capability in excess of 4 kW compared to a specification input maximum of 1500 W.

Schiavone, F.↗

High-temperature test facility at the NASA Lewis engine components research laboratory

The high temperature test facility (HTTF) at NASA-Lewis Engine Components Research Laboratory (ECRL) is presently used to evaluate the survivability of aerospace materials and the effectiveness of new sensing instrumentation in a realistic afterburner environment. The HTTF has also been used for advanced heat transfer studies on aerospace components. The research rig uses pressurized air which is heated with two combustors to simulate high temperature flow conditions for test specimens. Maximum airflow is 31 pps. The HTTF is pressure rated for up to 150 psig. Combustors are used to regulate test specimen temperatures up to 2500 F. Generic test sections are available to house test plates and advanced instrumentation. Customized test sections can be fabricated for programs requiring specialized features and functions. The high temperature test facility provides government and industry with a facility for testing aerospace components. Its operation and capabilities are described.

Colantonio, Renato O.↗

Test stand 116 at the Marshall Space Flight Center

A discussion of propulsion component testing in general and the capabilities of Test Stand 116 at the Marshall Space Flight Center (MSFC) in particular will serve to educate the aerospace community concerning this national resource. Historical significance, facility systems and capabilities, and day-to-day test operations are the focus of this discussion.

Best, Philip↗

Arc-Heater Facility for Hot Hydrogen Exposure of Nuclear Thermal Rocket Materials

A hyper-thermal environment simulator is described for hot hydrogen exposure of nuclear thermal rocket material specimens and component development. This newly established testing capability uses a high-power, multi-gas, segmented arc-heater to produce high-temperature pressurized hydrogen flows representative of practical reactor core environments and is intended to serve. as a low cost test facility for the purpose of investigating and characterizing candidate fueUstructura1 materials and improving associated processing/fabrication techniques. Design and development efforts are thoroughly summarized, including thermal hydraulics analysis and simulation results, and facility operating characteristics are reported, as determined from a series of baseline performance mapping tests.

Litchford, Ron J.↗

Design, fabrication and delivery of a miniature Cassegrainian concentrator solar array system

The optical design of the miniature Cassegrainian concentrator (MCC) element was improved for both offpoint and onpoint power capability. The cell stack design has shown no losses under the high short term thermal stresses imposed by component level test and is projected to be capable of greater than five years thermal cycle life in low Earth orbit. The structural design met all requirements for stiffness and flatness and requires adjustable inserts for fine tuning of the GFRP structure to meet flatness goals. The completed, fully populated small and large MCC panels deliverable under this contract perform electrically as expected. A solid acceptance inspection program to guarantee quality of all purchased parts, and continued manufacturing process improvements will make the MCC design a viable low cost alternative to standard flat panel technology. Minor improvements to the cell stack design of the MCC element can make significant improvements in both the performance and manufacturability of the MCC system.

Kruer, Mark A.↗

S-band Network Analysis and Strategies for LEO Multi-CubeSat Science Missions

This paper presents the network architecture utilized at NASA’s Goddard Space Flight Center (GSFC) to support a mission set of five 6U CubeSats. These five CubeSats employ a multi-waveform Software Defined Radio (SDR) platform developed by Vulcan Wireless for use with NASA’s Space Relay (SR) and Direct to Earth (DTE) networks. The performance testing of the SDR is discussed via a comprehensive S-band and communication link analysis. The tested capabilities of the SDR and antenna components are reviewed in terms of the mission requirements for each CubeSat. Size Weight and Power (SWaP), required availability, and access times are discussed. The measured data from experimental compatibility testing is incorporated into detailed simulations of the CubeSat mission set to verify desired performance over the mission lifetime. The model is also used to investigate the impact of potential adverse effects on the communication links such as interference and weather conditions. This paper also reviews potential improvements from future technological advances and commercial partnerships. A collaborative investigation between GSFC and Oklahoma State University is presented in which a qualitative analysis of Hybrid RF/Optical communication strategies is performed. The data rate improvements of optical communication techniques are weighed against attitude control and science mission requirements for CubeSats, and network architectures/switching strategies are discussed. A separate analysis reviews the potential benefits of ground station partnerships, which aligns with NASA’s future goal to include commercial partners in its Earth and space network architectures, e.g. LunaNet.

Space networks↗

A 7700 hour endurance test of a 30-cm Kaufman thruster

This paper describes an ongoing endurance test of the ion thruster which is expected to form the basis of future prime propulsion systems. The purpose of the test is to demonstrate the lifetime capability of such critical components as cathodes, vaporizers, isolators, and optics. The endurance test was preceded by development of an ion engine life test system and several intermediate duration tests. The elements of the test system are briefly described and the thruster modifications which resulted from the intermediate tests are evaluated in terms of the endurance test results. Thruster performance during the endurance test is described as well as the conclusions that can be drawn from the 8600 hours that have been completed as of March 6, 1975.

Collett, C. R.↗

Preburner of Staged Combustion Rocket Engine

A regeneratively cooled LOX/hydrogen staged combustion assembly system with a 400:1 expansion area ratio nozzle utilizing an 89,000 Newton (20,000 pound) thrust regeneratively cooled thrust chamber and 175:1 tubular nozzle was analyzed, assembled, and tested. The components for this assembly include two spark/torch oxygen-hydrogen igniters, two servo-controlled LOX valves, a preburner injector, a preburner combustor, a main propellant injector, a regeneratively cooled combustion chamber, a regeneratively cooled tubular nozzle with an expansion area ratio of 175:1, an uncooled heavy-wall steel nozzle with an expansion area ratio of 400:1, and interconnecting ducting. The analytical effort was performed to optimize the thermal and structural characteristics of each of the new components and the ducting, and to reverify the capabilities of the previously fabricated components. The testing effort provided a demonstration of the preburner/combustor chamber operation, chamber combustion efficiency and stability, and chamber and nozzle heat transfer.

Yost, M. C.↗

Test-Analysis Correlation for Space Shuttle External Tank Foam Impacting RCC Wing Leading Edge Component Panels

The Space Shuttle Columbia Accident Investigation Board recommended that NASA develop, validate, and maintain a modeling tool capable of predicting the damage threshold for debris impacts on the Space Shuttle Reinforced Carbon-Carbon (RCC) wing leading edge and nosecap assembly. The results presented in this paper are one part of a multi-level approach that supported the development of the predictive tool used to recertify the shuttle for flight following the Columbia Accident. The assessment of predictive capability was largely based on test analysis comparisons for simpler component structures. This paper provides comparisons of finite element simulations with test data for external tank foam debris impacts onto 6-in. square RCC flat panels. Both quantitative displacement and qualitative damage assessment correlations are provided. The comparisons show good agreement and provided the Space Shuttle Program with confidence in the predictive tool.

Lyle, Karen H.↗

Apollo 17 mission. Mapping camera extension mechanism operated erratically

The erratic operation of the mapping camera assemblies on board Apollo 15, 16, 17 is investigated. The exact causes of the problems with the scientific equipment module deployment mechanisms are not identified. However, the possibility of increased friction in hard vacuum is implied. It is suggested that since hard vacuum conditions are not attainable in large chambers, realistically loaded components could be tested in small chambers capable of vacuums to 10 to the minus 14th power torr. It is concluded that this technique carries with it the greatest promise for future investigations.

Source record↗

A Method for Calculating the Probability of Successfully Completing a Rocket Propulsion Ground Test

Propulsion ground test facilities face the daily challenge of scheduling multiple customers into limited facility space and successfully completing their propulsion test projects. Over the last decade NASA s propulsion test facilities have performed hundreds of tests, collected thousands of seconds of test data, and exceeded the capabilities of numerous test facility and test article components. A logistic regression mathematical modeling technique has been developed to predict the probability of successfully completing a rocket propulsion test. A logistic regression model is a mathematical modeling approach that can be used to describe the relationship of several independent predictor variables X(sub 1), X(sub 2),.., X(sub k) to a binary or dichotomous dependent variable Y, where Y can only be one of two possible outcomes, in this case Success or Failure of accomplishing a full duration test. The use of logistic regression modeling is not new; however, modeling propulsion ground test facilities using logistic regression is both a new and unique application of the statistical technique. Results from this type of model provide project managers with insight and confidence into the effectiveness of rocket propulsion ground testing.

Messer, Bradley↗

Systems test facilities existing capabilities compilation

Systems test facilities (STFS) to test total photovoltaic systems and their interfaces are described. The systems development (SD) plan is compilation of existing and planned STFs, as well as subsystem and key component testing facilities. It is recommended that the existing capabilities compilation is annually updated to provide and assessment of the STF activity and to disseminate STF capabilities, status and availability to the photovoltaics program.

Weaver, R.↗

MSFC Skylab Orbital Workshop, volume 3

The waste management system for the Skylab Orbital Workshop is discussed. The general requirements of the system are presented. Illustrations of the components of the system are provided. Data concerning maximum expected performance capabilities are developed. The results of performance tests on the system components are reported. Emphasis is placed on the human factors engineering aspects of the system.

Source record↗

A versatile system for biological and soil chemical tests on a planetary landing craft. II - Hardware development

A system has been under development which is designed to seek remotely for clues to life in planetary soil samples. The basic approach is a set of experiments, all having a common sensor, a gas analysis mass spectrometer which monitors gas composition in the head spaces above sealed, temperature controlled soil samples. Versatility is obtained with up to three preloaded, sealed fluid injector capsules for each of eleven soil test cells. Tests results with an engineering model has demonstrated performance capability of subsystem components such as soil distribution, gas sampling valves, injector mechanisms, temperature control, and test cell seal.

Martin, J. P.↗

The Business Case for Spiral Development in Heavy Lift Launch Vehicle Systems

Performance capabilities of a specific combination of the Space Shuttle external tank and various liquid engines in an in-line configuration, two-stage core vehicle with multiple redesigned solid rocket motor strap-ons are reexamined. This concept proposes using existing assets, hardware, and capabilities that are already crew-rated, flight certified, being manufactured under existing contracts, have a long history of component and system ground testing, and have been flown for over 20 yr. This paper goes beyond describing potential performance capabilities of specific components to discuss the overall system feasibility-from end to end, start to finish-describing the inherent cost advantages of the Spiral Development concept, which builds on existing capabilities and assets, as opposed to starting up a "fresh sheet" heavy-lift launch vehicle program from scratch.

Farr, Rebecca A.↗