Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep mechanisms”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Improved creep performance of CoCrFeNi high entropy alloys by Mo addition

The CoCrFeNi family of high entropy alloys has good mechanical and corrosion properties, performing like stainless steels with low yield stresses. They could, however, benefit from hardening methods for structural and high temperature applications. Here, this work investigates the potential for the CoCrFeNi alloy to be hardened with the addition of Mo. A series of CoCrFeNiMo alloys and their CoCrFeNi counterparts were subsequently manufactured at NETL and then mechanically creep tested at 650°C. The alloys were designed to possess a range of stacking fault energies which influence the mechanical properties of the alloys via the motion of their dislocations under stress. Results show that Mo-containing variants have creep rupture lives ranging from 4000 to 8000 hours, i.e., about two orders of magnitude longer than those for Mo-free variants. The significantly improved creep performance of the Mo-containing alloys is due to a combination of solid solution strengthening and precipitation strengthening from µ-phase and carbides.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of the Addition of a Low Equivalent Stress Mechanism to the Analysis of Geomechanical Behavior of the SPR West Hackberry Site

Sandia National Laboratories has long used the Munson-Dawson (M-D) model to predict the geomechanical behavior of salt caverns used to store oil at the Strategic Petroleum Reserve (SPR). Salt creep causes storage caverns to deform inward, thus losing volume. This loss of volume affects the salt above and around the caverns, puts stresses and strains on borehole casings, and creates surface subsidence which affects surface infrastructure. Therefore, accurate evaluation of salt creep behavior drives decisions about cavern operations. Parameters for the M-D model are typically fit against laboratory creep tests, but nearly all historic creep tests have been performed at equivalent stresses of 8 MPa or higher. Creep rates at lower equivalent stresses are very slow, such that tests take months or years to run, and the tests are sensitive to small temperature perturbations (<0.1°C). A recent collaboration between US and German researchers, recently characterized the creep behavior at low equivalent (deviatoric) stresses (<8 MPa) of salt from the Waste Isolation Pilot Plant. In addition, the M-D model was recently extended to include a low stress creep “mechanism”. This paper details new simulations of SPR caverns that use this extended M-D model, called the M-D Viscoplastic model. The results show that the inclusion of low stress creep significantly alters the prediction of steady-state cavern closure behavior and indicate that low stress creep is the dominant displacement mechanism at the dome scale. The implications for evaluating cavern and well integrity are demonstrated by investigating three phenomena: the extent of stress changes around the cavern; the predicted vertical strains applied to wellbore casings; and the evaluation of oscillating stress changes around the cavern due to oil sale cycles and their potential effect on salt fatigue.

58 GEOSCIENCES↗
DOE OSTI2021

Accelerated molecular dynamics simulations of dislocation climb in nickel

We report the mechanical behavior of materials operating under high temperatures is strongly influenced by creep mechanisms such as dislocation climb, which is controlled by the diffusion of vacancies. However, atomistic simulations of these mechanisms have traditionally been impractical due to the long time scales required. To overcome these time scale challenges, we use Parallel Trajectory Splicing (ParSplice), an accelerated molecular dynamics method, to simulate dislocation climb in nickel. We focus on modeling the activity of a vacancy near a jog on an edge dislocation in order to observe vacancy pipe diffusion and vacancy absorption at the jog. From rigorously constructed trajectories encompassing more than 2000 vacancy absorption events over a simulation time of more than 4μs at 900 K, a comprehensive sampling of available atomistic mechanisms is collated and analyzed further with molecular statics calculations. We estimate average rates for pipe diffusion and vacancy absorption into the jog using data from the dynamic and static calculations, finding very good agreement. Our results strongly suggest that the dominant mechanism for vacancy absorption by jogs is via biased diffusion to the dislocation core followed by fast pipe diffusion to the jog.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Creep properties of advanced austenitic steel 709 determined through short experiments under in-situ neutron diffraction followed by TEM characterization

Here in this study, the creep mechanisms at play in Alloy 709 (Fe-20Cr-25Ni) are investigated by performing short-term creep-type tests under in-situ neutron diffraction experiments. Short tests are performed in the temperature range of 500 to 900 °C under constant load with a load ranging from 50 to 150 MPa. The creep exponent and activation energy are determined using the Bird-Mukherjee-Dorn relation and compared to that obtained from conventional longer creep tests from the literature. Scanning transmission electron microscopy (S/TEM) of the post-creep microstructure indicates that interaction of dislocations with precipitates are a dominant mechanism at play. Furthermore, local elemental mapping indicated chemical segregation at grain boundaries and formation of complex precipitates.

36 MATERIALS SCIENCE↗
NASA NTRS1981

Elevated temperature mechanical properties and residual tensile properties of two cast superalloys and several nickel-base oxide dispersion strengthened alloys

The elevated temperature tensile, stress-rupture and creep properties and residual tensile properties after creep straining have been determined for two cast superalloys and several wrought Ni-16Cr-4Al-yttria oxide dispersion strengthened (ODS) alloys. The creep behavior of the ODS alloys is similar to that of previously studied ODS nickel alloys. In general, the longitudinal direction is stronger than the long transverse direction, and creep is at least partially due to a diffusional creep mechanism as dispersoid-free zones were observed after creep-rupture testing. The tensile properties of the nickel-base superalloy B-1900 and cobalt-base superalloy MAR-M509 are not degraded by prior elevated temperature creep straining (at least up to 1 pct) between 1144 and 1366 K. On the other hand, the room temperature tensile properties of ODS nickel-base alloys can be reduced by prior creep strains of 0.5 pct or less between 1144 and 1477 K, with the long transverse direction being more susceptible to degradation than the longitudinal direction.

Whittenberger, J. D.↗
DOE OSTI2021

Assessing the ASME Section III, Division 5, Class A Primary Load Design Rules Against Creep Notch Effects

This report assesses the ASME Section III, Division 5, Subsection HB, Subpart B rules covering the design and construction of high temperature Class A nuclear reactor components for their robustness against creep notch effects. The creep notch effect combines the effect of multiaxial stresses on material creep deformation and damage. This report considers both effects, including the potential for creep mechanism shifts affecting the extrapolation of design data from high stress, short-time experimental data to low stress, long time operating component conditions. The report summarizes the history of and literature on multiaxial creep and surveys the current ASME design rules dealing with multiaxial effects. The report then describes the results of two dedicated numerical studies, one assessing the robustness of the ASME rules against uncertainty in extrapolating from uniaxial creep test data to multiaxial component conditions and a second study examining the potential effects of a mechanism shift from high stress, dislocation-mediated creep to diffusion-dominated creep at lower stresses. The final conclusion of the report is that the ASME rules adequately guard against multiaxial creep failure, though there are several aspects of the Code that could be optimized to provide less over-conservative design predictions or to provide a more consistent design margin as a function of temperature and stress. In a few areas, particularly the potential for mechanism shifts outside the currently-available experimental data, the Code rules should be revaluated as additional experimental data and new modeling and simulation results become available

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Effect of Transverse Compression on the Dielectric Breakdown of Power Cable with Ethylene Propylene Rubber Insulation

Understanding of the failure mechanisms of submarine dynamic power cables (SDPC) is critical for innovative design to meet the 2035 cost reduction target of U.S. DOE Floating Offshore Wind Shot. This is important because the current design suffers a significant failure rate in the field. This project explored a multiphysics approach and conducted systematic electro-thermo-mechanical (ETM) experimental study on the power cores extracted from a 15 kV power cable. The power cable had three cores of copper conductor and ethylene propylene rubber (EPR) insulation. An ETM testing system with transverse compression capability was developed. Mechanical loading induced dielectric breakdown. Increasing temperature from room temperature (RT, 22 degrees Celsius) to 90 degrees Celsius resulted in the 67% decrease in the failure mechanical load as defined by the dielectric breakdown. With the same temperature rise, the creep mechanical load was reduced by 70% at a given dielectric breakdown time. The post-test measurement revealed an impressive recovery of electrical resistance, although the dielectric breakdown occurred in the ETM test that would not be captured without the use of ETM testing.

Wang, Hong [ORNL] (ORCID:0000000201730545)↗
DOE OSTI2024

Vacancy-mediated transport and segregation tendencies of solutes in fcc nickel under diffusional creep: A density functional theory study

The Nabarro-Herring (NH) diffusional creep theory postulates the vacancy-mediated transport of atoms under a stress gradient as the creep mechanism under low-stress and high-temperature conditions. In multicomponent alloys, we premise that this stress-assisted flow of vacancies to and from grain boundaries will produce elemental segregation. An observation of such segregation, validated with theoretical predictions, can provide the necessary experimental evidence for the occurrence of NH creep. Theoretical calculations of the segregation tendencies via analyzing the dominant solute diffusion mechanisms and the difference in diffusivities of the elements are therefore essential. To this end, this study applies density functional theory calculations of migration barriers and solute-vacancy binding energies as input to the self-consistent mean-field theory to assess the vacancy-mediated diffusion mechanisms, transport coefficients, and segregation tendencies of Co, Cr, Mo, Re, Ta, and W solutes in face-centered-cubic Ni. We find Co, Re, and W to be slow diffusers at high temperatures and Cr, Mo, and Ta to be fast diffusers. Further analysis shows that the slow diffusers tend to always enrich at vacancy sinks over a wide range of temperatures. In contrast, the fast diffusers show a transition from depletion to enrichment as the temperature lowers. Furthermore, our analysis of the segregation tendencies under tensile hydrostatic strains shows that slow diffusers are largely unaffected by the strain and favor enrichment. On the other hand, the fast diffusers exhibit high sensitivity to strain and their segregation tendency can transition from depletion to enrichment at a given temperature. Finally, the transport coefficients calculated in this work are expected to serve as input to mesoscale microstructure models to provide a more rigorous assessment of solute segregation under NH creep conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-Temperature Tensile and Creep Test Results on Thin Wall Tube Specimens of ODS Alloys 14YWT and OFRAC

High-temperature tensile and strain rate jump (SRJ) creep tests were conducted on axial specimens fabricated from thin wall tubes of the oxide dispersion strengthened (ODS) alloys 14YWT and OFRAC. The dimensions of the 14YWT thin wall tube was 10.7 mm OD, 0.5 mm WT and 0.92 m and of the OFRAC thin wall tube was 8.5 mm OD + 0.5 mm WT and 1.78 m in length. The axial specimens fabricated from the thin wall tubes were based on a dual-gauge design with gauge dimensions of 4 mm long and 2 mm wide. The tensile tests were conducted in air at 800ºC, 900ºC and 1,000ºC and the SRJ creep tests were conducted in air at 800ºC. Two axial specimens were used in each tensile and SRJ creep tests. The results of the tensile tests showed much lower yield stress (YS) compared to ultimate tensile strength (UTS) indicative of large work hardening properties. The results showed the UTS of OFRAC was higher than that of 14YWT by ~35 MPa at 800ºC. At 900ºC, the UTS of OFRAC and 14YWT was similar at 900ºC and at 1000ºC, the UTS of 14YWT was higher than that of OFRAC by ~10 MPa. The ductility properties of OFRAC were greater than that of 14YWT with higher values of uniform elongation (UE) and total elongation (TE) at all tensile test temperatures. The creep properties of 14YWT and OFRAC were evaluated by the strain rate jump test method at 800ºC. The stress exponent (n) for creep was obtained from the SRJ test data by plotting the values of the log strain rate against the log stress, which is measured from the stress-strain curve generated during the SRJ test. The results showed the highest stress exponents of n = 19.8 and n = 35.0 were measured from the two SRJ tests on 14YWT. The stress exponent measured from one successful SRJ test on OFRAC was n = 13.3, which was lower than that of 14YWT. Nevertheless, these high values of stress exponent are consistent with ODS ferritic alloys such as 14YWT and OFRAC since they indicate dislocation-particle interactions are the dominant creep mechanism for specific ranges of temperature and stress. The results obtained from the tensile and SRJ creep tests conducted on axial specimens in this study indicate that 14YWT and OFRAC retain high strengths at temperatures up to 1,000ºC and good creep performance at 800ºC.

36 MATERIALS SCIENCE↗
NASA NTRS1973

Fabrication of aluminum-carbon composites

A screening, optimization, and evaluation program is reported of unidirectional carbon-aluminum composites. During the screening phase both large diameter monofilament and small diameter multifilament reinforcements were utilized to determine optimum precursor tape making and consolidation techniques. Difficulty was encountered in impregnating and consolidating the multifiber reinforcements. Large diameter monofilament reinforcement was found easier to fabricate into composites and was selected to carry into the optimization phase in which the hot pressing parameters were refined and the size of the fabricated panels was scaled up. After process optimization the mechanical properties of the carbon-aluminum composites were characterized in tension, stress-rupture and creep, mechanical fatigue, thermal fatigue, thermal aging, thermal expansion, and impact.

Novak, R. C.↗
DOE OSTI2022

Analysis of Microwave Resonant Cavity Transducer Degradation Mechanisms

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. Because the transducer is intended for immersion in a high temperature corrosive fluid, understanding of material degradation is crucial for estimation of transducer performance lifetime, and development of measurement interpretation algorithms. We conducted a preliminary computational investigation of relevant damage mechanisms of a stainless steel 316 cylindrical resonator in FLiBe salt. The two main damage mechanisms, creep and corrosion, were modeled using multiphysics COMSOL software. Degradation was modeled for a temperature range 500°C to 700°C. Coupling of the damage mechanisms was not considered. These models predict significant inelastic deformation at most temperatures due to creep, and qualitatively predict chromium depletion both along the liquid/solid interface and along the grain boundaries. An algorithmic approach for compensation of these degradation effects during fluid flow measurements will be developed in the future work.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Second Annual Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with the flat wall of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the resonant frequency, which can be detected with a spectrum analyzer. Because the transducer is intended for immersion in a high temperature corrosive fluid, understanding of material degradation is crucial for estimation of transducer performance lifetime, and development of measurement interpretation algorithms. We conducted a preliminary computational investigation of relevant damage mechanisms of a stainless steel 316 cylindrical resonator in FLiBe salt. The two main damage mechanisms, creep and corrosion, were modeled using multiphysics COMSOL software. Degradation was modeled for a temperature range 500°C to 700°C. Coupling of the damage mechanisms was not considered. These models predict significant inelastic deformation at most temperatures due to creep, and qualitatively predict chromium depletion both along the liquid/solid interface and along the grain boundaries. An algorithmic approach for compensation of these degradation effects during fluid flow measurements will be developed in the future work. To validate sensor physics, we have performed proof-of-principle test of flow sensing in water. For this test, we have developed a cylindrical resonator for K-band, which was machined from brass. The cavity was excited through WR-42 waveguide through a subwavelength hole on the side of the wall of the cylinder. To increase the spectral signal visibility, we developed a signal processing method for baseline subtraction. A flow loop for proof-of-principle test of transducer performance in water was assembled. A commercial flow meter was installed in the loop for reference measurements. Cylindrical cavity was excited in the TE 011 mode with resonant frequency f ≈ 17.8GHz. Frequency shift of cavity spectral response was obtained by gradually increasing water flow rate from 0 to 60gpm. Corresponding monotonic increase of resonant frequency shift by several MHz was observed. Approximate figure of merit of sensitivity to flow rate is 100KHz/GPM. In addition, we have identified an existing liquid sodium experimental setup for demonstration of flow sensing in environment similar to that of an advanced reactor. The setup consists of a cylindrical vessel and center feed line, where transducer inserted through the lid will measure velocity of the impinging liquid jet. As a calibration experiment, we have assembled a water vessel with center feed with the same dimensions as those of the liquid sodium setup. We have also developed and insertion probe consisting of a 50cm brass waveguide enclosed in protective SS316 tube. Using the water loop, we have demonstrated feasibility of sensing the impinging liquid jet in the vessel.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Progression of creep deformation from grain boundaries to grain interior in Al-Cu-Mn-Zr alloys

Creep mechanisms are studied in θ'-Al 2 Cu-strengthened Al-Cu-Mn-Zr alloys at 300 and 350°C for (i) ACMZ, a base alloy without further alloying elements and (ii) RR350, a commercial alloy with additions of Ni and Co forming distinct grain-boundary precipitates. At high stresses, creep is dominated by dislocations bypassing θ' precipitates within grains via the Orowan mechanism, as evidenced by (i) very high stress exponent (n~20-25) and (ii) α-Al and θ' lattice strains (measured via in-situ neutron diffraction) evolving during creep in a manner consistent with load transfer from the plastically-deforming α-Al matrix to elastically-deforming θ' precipitates. At intermediate stresses, both alloys exhibit a n~3 regime, where α-Al and θ' lattice strains scale near-linearly with applied stress while remaining largely unaffected by strain accumulation, indicating that Orowan looping or dislocation pile-up around θ' is now inactive within the grains. Rather, dislocation motion occurs solely in θ'-precipitate-free zones (θ'-PFZ) where high dislocation densities are observed via TEM after creep deformation. Plastic flow at θ'-PFZ and/or localized pipe diffusion are expected to enable grain-boundary sliding (GBS), which is proposed as the rate-limiting mechanism in the n~3 regime. Ni/Co-rich precipitates at RR350 grain-boundaries, with negligible θ'-PFZ around them, share load (as determined via neutron diffraction) with the α-Al matrix more effectively than θ-Al 2 Cu precipitates at ACMZ grain-boundaries, with wide surrounding θ'-PFZ. So, high creep resistance in the n~3 GBS regime of RR350 is enabled by coarsening-resistant grain-boundary precipitates, forming without concomitant development of weak θ'-PFZ, which effectively share load with the grains.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Creep ductility limiting mechanisms in an additively manufactured Al-Ce-Ni-Mn-Zr alloy

Tensile creep response and cavitation damage evolution in an additively manufactured Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt%) alloy with peak-aging and overaging treatments were investigated in the 300–400 ºC range. Microstructural heterogeneity and its response to heat treatment and subsequent creep deformation were studied to understand the interplay between cavity formation, creep lifetime and ductility. Increasing the applied stress activated the nucleation of more cavities, an experimental observation that is well described using the vacancy accumulation model. Cavities nucleated prematurely due to localized plasticity in the denuded zones that formed at/near melt-pool or grain boundaries. Microstructure/deformation heterogeneity with consequent evolution of stress triaxiality, especially at lower stresses, causes accelerated cavitation, thus producing low creep ductility (∼ 0.2–2.4 %), compared to (∼12–21 %) ductility of the alloy measured by regular tensile tests at equivalent temperatures. A constrained diffusional cavity growth mechanism with continuous cavity nucleation during creep is established as the dominant mechanism, implying that cavitation involves vacancy diffusion, yet its growth rate is dictated by the minimum creep rate. In conclusion, the ductility-limiting creep and cavitation mechanisms discussed here provide new insight into the creep behavior of 3D-printed metallic alloys.

Additive manufacturing↗
NASA NTRS1999

Determination of Creep Behavior of Thermal Barrier Coatings Under Laser Imposed High Thermal and Stress Gradient Conditions

A laser sintering/creep technique has been established to determine the creep behavior of thermal barrier coatings under steady-state high heat flux conditions. For a plasma sprayed zirconia-8 wt. % yttria coating, a significant primary creep strain and a low apparent creep activation energy were observed. Possible creep mechanisms involved include stress induced mechanical sliding and temperature and stress enhanced cation diffusion through the splat and grain boundaries. The elastic modulus evolution, stress response, and total accumulated creep strain variation across the ceramic coating are simulated using a finite difference approach. The modeled creep response is consistent with experimental observations.

Zhu, Dongming↗
NASA NTRS1999

Special Considerations in Selection of Fabric Film Laminates for Use in Inflatable Structures

Inflatable structures are gaining wide support in planetary scientific missions as well as commercial applications. For such applications a new class of fabric/film laminates is being considered for use as a structural gas envelope. The emerging composite materials are a result of recent advances in the manufacturing of lightweight, high strength fibers, fabrics and scrims. The lamination of these load-carrying members with the proper gas barriers results in a wide range of materials suitable for various loading and environmental conditions. Polyester-based woven fabrics laminated to thin homogenous film of polyester are an example of this class. This fabric/film laminate is being considered for the development of a material suitable for building large gas envelopes for use in the NASA ultra long duration balloon program (ULDB). Compared to commercial homogenous films, the material provides relatively high strength to weight ratio as well as better resistance to crack and tear propagation, The mechanical, creep and viscoelastic properties of these fabric film laminates have been studied to form a material model. Preliminary analysis indicates that the material is highly viscoelastic. The mechanical properties of this class of materials will be discussed in some details.

Said, Magdi A.↗
NASA NTRS1991

Differential continuum damage mechanics models for creep and fatigue of unidirectional metal matrix composites

Three multiaxial isothermal continuum damage mechanics models for creep, fatigue, and creep/fatigue interaction of a unidirectional metal matrix composite volume element are presented, only one of which will be discussed in depth. Each model is phenomenological and stress based, with varying degrees of complexity to accurately predict the initiation and propagation of intergranular and transgranular defects over a wide range of loading conditions. The development of these models is founded on the definition of an initially transversely isotropic fatigue limit surface, static fracture surface, normalized stress amplitude function and isochronous creep damage failure surface, from which both fatigue and creep damage evolutionary laws can be obtained. The anisotropy of each model is defined through physically meaningful invariants reflecting the local stress and material orientation. All three transversely isotropic models have been shown, when taken to their isotropic limit, to directly simplify to previously developed and validated creep and fatigue continuum damage theories. Results of a nondimensional parametric study illustrate (1) the flexibility of the present formulation when attempting to characterize a large class of composite materials, and (2) its ability to predict anticipated qualitative trends in the fatigue behavior of unidirectional metal matrix composites. Additionally, the potential for the inclusion of various micromechanical effects (e.g., fiber/matrix bond strength, fiber volume fraction, etc.), into the phenomenological anisotropic parameters is noted, as well as a detailed discussion regarding the necessary exploratory and characterization experiments needed to utilize the featured damage theories.

Arnold, S. M.↗