Search NASA⌕ Search

SEARCH · Search NASA

Results for “Creep resistance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

NiCrMoNb age hardenable alloy for creep-resistant high temperature applications, and methods of making

Nickel alloys, methods of making nickel alloys, articles including the nickel alloys, uses of the alloys, and methods of treating nickel alloys are described. The inventive heat resistant structural materials are suitable for applications requiring high yield stress at room temperature and good creep strength at high temperatures, such as in gas turbines, steam turbines, fossil energy boilers, aero engines, power generation systems using fluids such as supercritical carbon dioxide (e.g., advanced ultra-supercritical power plants), concentrated solar power plants, nuclear power plants, molten salt reactors: turbine blades, casings, valves, heat exchangers and recuperators.

Detrois, Martin↗
NASA NTRS2005

Non-contact Creep Resistance Measurement for Ultra-high temperature Materials

Continuing pressures for higher performance and efficiency in propulsion are driving ever more demanding needs for high-temperature materials. Some immediate applications in spaceflight include combustion chambers for advanced chemical rockets and turbomachinery for jet engines and power conversion in nuclear-electric propulsion. In the case of rockets, the combination of high stresses and high temperatures make the characterization of creep properties very important. Creep is even more important in the turbomachinery, where a long service life is an additional constraint. Some very high-temperature materials are being developed, including platinum group metals, carbides, borides, and silicides. But the measurement of creep properties at very high temperatures is itself problematic, because the testing instrument must operate at such high temperatures. Conventional techniques are limited to about 1700 C. A new, containerless technique for measuring creep deformation has been developed. This technique is based on electrostatic levitation (ESL) of a spherical sample, which is heated to the measurement temperature and rotated at a rate such that the centrifugal acceleration causes creep deformation. Creep of samples has been demonstrated at up to 2300 C in the ESL facility at NASA MSFC, while ESL itself has been applied at over 3000 C, and has no theoretical maximum temperature. The preliminary results and future directions of this NASA-funded research collaboration will be presented.

Hyers, Robert W.↗
DOE OSTI2020

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Low-cost, high-strength, cast creep-resistant alumina-forming alloys for heat-exchangers, supercritical CO2 systems and industrial applications

An austenitic Ni-base alloy includes, in weight percent: 2.5 to 4.75 Al; 13 to 21 Cr; 20 to 40 Fe; 2 to 5 total of at least one element selected from the group consisting of Nb and Ta; 0.25 to 4.5 Ti; 0.09 to 1.5 Si; 0 to 0.5 V; 0 to 2 Mn; 0 to 3 Cu; 0 to 2 of Mo and W; 0 to 1 of Zr and Hf; 0 to 0.15 Y; 0.01 to 0.45 C; 0.005 to 0.1 B; 0 to 0.05 P; less than 0.06 N; and balance Ni (38 to 46 Ni). The weight percent Ni is greater than the weight percent Fe. An external continuous scale comprises alumina. A stable phase FCC austenitic matrix microstructure is essentially delta-ferrite-free, and contains one or more carbides and coherent precipitates of γ′ and exhibits creep rupture life of at least 100 h at 900° C. and 50 MPa.

Muralidharan, Govindarajan↗
DOE OSTI2024

Modelling of cracking during beam oscillation laser welding of a creep-resistant nickel alloy

During high power laser welding of Inconel 740H, horizontal solidification cracks form at locations between approximately 70–80% of the weld depth. With the integration of circular beam oscillation, the laser energy density distribution and underlying thermo-mechanical conditions were altered. By coupling three-dimensional heat transfer, fluid flow, and stress modelling tools, the role that circular beam oscillation plays in the formation of the strain rates and stresses driving this cracking phenomenon was identified. While the addition of a circular oscillation pattern appeared to lower the stress levels along the solidification front, it did not eliminate the appearance of horizontal cracking. Only when the beam amplitudes reached 1.6 mm did solidification cracking disappear, but the weld depths were also significantly reduced.

Gao, Mingze↗
DOE OSTI2025

Production of Creep-Resistant FeCrAl-ODS

Four ODS FeCrAl alloys with base alloy composition Fe-16Cr-4Al-2Mo-0.2Y (wt.%) were mechanically alloyed with minor additions of CeO 2 and Y 2 O 3 additions and were successfully extruded into rectangular-shaped bars. Two oxide compositions were explored, which were designated NC with oxide addition of 0.5CeO 2 plus 0.2Yin solution of the base alloy powder and PC with additions of 0.5CeO 2 and 0.7Y 2 O 3 to elevate the O level. The microstructure of both alloys revealed by SEM and EBSD to consist of very small grains with sizes of ~450-520 nm and weak texture components. Sub-size tensile specimens fabricated from both alloys were tensile tested from room temperature to 800ºC. The results for both alloys from room temperature to 400ºC showed very high strengths, but low ductilities, especially uniform strain. From 500ºC to 800ºC, the strengths decreased rapidly, and the ductilities increased significantly. The reason for the rapid decreases in tensile strengths above 500ºC for both alloys is not clear, but will require advanced characterization techniques including atom probe tomography, to determine the size and number density of the nano-size oxide particles, and TEM/EFTEM, for investigating the dispersion of nano-size oxide particles on grain boundaries to assess the Zener grain boundary pinning effect, which will hinder grain coarsening at high temperatures that may enhance the Hall Petch strengthening mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Tensile and compressive creep properties of a quaternary Al-Cu-Mn-Zr (ACMZ) alloy and its commercial counterpart (Al-Cu-Mn-Zr with Ni, Co and Sb additions, RR350) are investigated at 300°C. At low stresses up to 30 MPa where diffusional creep dominates, creep resistance is the same in tension and compression and RR350 deforms more slowly than ACMZ, consistent with RR350 alloy's larger linear fraction of intergranular precipitates (Al7Cu2(NiFe) and Al9FeNi for RR350 vs. θ-Al2Cu for ACMZ) and a reduced fraction of precipitate-free zones near grain boundaries. At stresses between 30 and 80 MPa, dislocation creep with a stress exponent n ~ 3 becomes rate-limiting in compression, which is expected to be controlled by θ' precipitates within the grain bulk. By contrast, in tension, enhanced creep rate and higher apparent stress exponents are measured, consistent with cavitation at intergranular precipitates becoming increasingly dominant as the stress increases. In the dislocation creep regime, RR350 alloy is again more creep resistant than ACMZ alloy, which is related to three mechanisms (i) a reduced fraction of softer precipitate-free zones, (ii) more effective load transfer to intergranular precipitates, and (iii) reduced cavitation. A model for cavitation is applied to calculate tensile creep rates from compressive creep rates and the model successfully predicts the improved tensile creep resistance of the RR350 alloy. Overall, the present investigation underscores the importance of intergranular grain boundary precipitates, in addition to strengthening θ' precipitates, in enhancing the creep resistance of Al-Cu alloys.

36 MATERIALS SCIENCE↗
NASA NTRS1995

A new Cu-8 Cr-4 Nb alloy for high temperature applications

Various applications exist where a high conductivity alloy with good strength and creep resistance are required. NASA LeRC has developed a Cu-8 at. percent Cr-4 at. percent Nb (Cu-8 Cr-4 Nb) alloy for these applications. The alloy is designed for use up to 700 C and shows exceptional strength, low cycle fatigue (LCF) resistance, and creep resistance. Cu-8 Cr-4 Nb also has a thermal conductivity of at least 72 percent that of pure Cu. Furthermore, the microstructure and mechanical properties of the alloy are very stable. In addition to the original application in combustion chambers, Cu-8 Cr-4 Nb shows promise for welding electrodes, brazing fixtures, and other applications requiring high conductivity and strength at elevated temperatures.

Ellis, D. L.↗
NASA NTRS1991

The high temperature creep behavior of oxides and oxide fibers

A thorough review of the literature was conducted on the high-temperature creep behavior of single and polycrystalline oxides which potentially could serve as fiber reinforcements in ceramics or metal matrix applications. Sapphire when oriented with the basal plane perpendicular to the fiber axis (c-axis oriented) is highly creep resistant at temperatures in excess of 1600 C and applied loads of 100 MPa and higher. Pyramidal slip is preferentially activated in sapphire under these conditions and steady-state creep rates in the range of 10(exp -7) to 10 (exp -8)/s were reported. Data on the creep resistance of polycrystalline beryllia suggest that C-axiz oriented single crystal beryllia may be a viable candidate as a fiber reinforcement material; however, the issure of fabricability and moisture sensitivity must be addressed for this material. Yttrium aluminum garnet (YAG) also appears to be a fiber candidate material having a high resistance to creep which is due to it's complex crystal structure and high Peierl resistance. The high creep resistance of garnet suggests that there may be other complex ternary oxides such as single crystal mullite which may also be candidate materials for fiber reinforcements. Finally, CVD and single crystal SiC, although not oxides, do possess a high resistance to creep in the temperature range between 1550 and 1850 C and under stresses of 110 to 220 MPa. From a review of the literature, it appears that for high creep resistant applications sapphire, silicon carbide, yttrium aluminum garnet, mullite, and beryllia are desirable candidate materials which require further investigation.

Jones, Linda E.↗
DOE OSTI2025

ULTIMATE Phase I project: Development of Niobium-based alloys for Turbine Applications

Current Ni-based alloys used in turbine blade applications are operating at 1100°C which is approximately 90% of the solidus of Ni-based alloys. Further increases in temperature can be achieved only through the use of alloys with higher solidus temperatures such as refractory alloys which include Mo, Nb, W, Ta alloys. Niobium has a unique combination of physical properties that include a high melting point (2468°C), lowest density (8.57 g/cc), and the lowest modulus amongst refractory alloys, a good thermal conductivity that increases from 45 W/mK at room temperature to 62 W/mK at 1093°C, good ductility with fabricability using traditional techniques, high strength, good creep resistance, and general chemical inactivity. Hence niobium alloys offer many advantages for use at the desired temperature of 1300°C. One of the major deterrents to the use of niobium and its alloys at high temperatures is achieving good oxidation resistance. In addition, achieving balanced properties of room temperature strength, ductility, fracture toughness, high temperature strength, and creep resistance required for 1300°C operation at a density of 9 g/cm 3 is extremely challenging since the addition of W which is a potent strengthener increases the density of the alloy. This project seeks to enable the development of a tri-layered turbine blade that can operate continuously at 1300°C with the core of the turbine blade providing good creep resistance, the second layer providing improved oxidation resistance over the core layer, and the third layer being an environmental barrier providing oxidation resistance. The objective of this Phase 1 project was to use computational modeling and advanced characterization tools to develop two classes of Nb alloys which could be used as the core layer and the transition layer. The first class of alloys developed in this project was a Nb-alloy designed to serve as the turbine blade core with excellent room temperature strength, ductility, and high temperature strength and creep resistance required for 1300°C operation. These alloys were designed to contain sufficient solute solution strengthening elements (W, Mo) but constrained by the density of alloy, along with the addition of elements such as Zr, Hf, Ta, C, and N to achieve a combination of primary and secondary carbide precipitation. A total of 38 “creep-resistant” alloys were designed and cast during the duration of the project. Processing techniques were developed to keep the oxygen contents as low as possible with typical oxygen contents less than 250 ppm. One alloy with a density of < 9.5 g/cc was successful in meeting the Phase 2 intermediate project mechanical property milestone requirements of room temperature ductility greater than 1.0%, 1200°C creep strain of less than 3% at 150 MPa and 100 hours in vacuum, and with solidus temperature greater than 1500ᵒC. The second class of alloys was designed to be a Nb-rich alloy with improved oxidation resistance when compared to the core layer and was designed specifically to be compatible with the core layer and the outer environmental barrier coating. This Nb- alloy will be specifically designed to be microstructurally stable at these temperatures when in contact with the core alloy and provide protection against catastrophic failure of the barrier coating. Two alloys were cast and processed but further development was discontinued to focus on the development of the creep resistant alloy.

36 MATERIALS SCIENCE↗