Search NASA⌕ Search

SEARCH · Search NASA

Results for “Crystallographic phases”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Motorized Beam Alignment of a Commercial X-ray Diffractometer

X-ray diffraction (XRD) is a powerful analysis method that allows researchers to noninvasively probe the crystalline structure of a material. This includes the ability to determine the crystalline phases present, quantify surface residual stresses, and measure the distribution of crystallographic orientations. The Structures and Materials Division at the NASA Glenn Research Center (GRC) heavily uses the on-site XRD lab to characterize advanced metal alloys, ceramics, and polymers. One of the x-ray diffractometers in the XRD lab (Bruker D8 Discover) uses three different x-ray tubes (Cu, Cr, and Mn) for optimal performance over numerous material types and various experimental techniques. This requires that the tubes be switched out and aligned between experiments. This alignment maximizes the x-ray tube s output through an iterative process involving four set screws. However, the output of the x-ray tube cannot be monitored during the adjustment process due to standard radiation safety engineering controls that prevent exposure to the x-ray beam when the diffractometer doors are open. Therefore, the adjustment process is a very tedious series of blind adjustments, each followed by measurement of the output beam using a PIN diode after the enclosure doors are shut. This process can take up to 4 hr to perform. This technical memorandum documents an in-house project to motorize this alignment process. Unlike a human, motors are not harmed by x-ray radiation of the energy range used in this instrument. Therefore, using motors to adjust the set screws will allow the researcher to monitor the x-ray tube s output while making interactive adjustments from outside the diffractometer. The motorized alignment system consists of four motors, a motor controller, and a hand-held user interface module. Our goal was to reduce the alignment time to less than 30 min. The time available was the 10-week span of the Lewis' Educational and Research Collaborative Internship Project (LERCIP) summer internship program and the budget goal was $1200. In this report, we will describe our motorization design and discuss the results of its implementation.

Van Zandt, Noah R.↗
NASA NTRS1993

Exsolved kirschsteinite in angrite LEW86010 olivine

Mineralogy of kirschsteinite exsolution in olivine from Antarctic meteorite LEW86010 has been studied by single crustal X-ray diffraction technique. The LEW86010 olivine crystals have exsolution lamellae of kirschteinite about 15 microns wide. Determination of crystallographic orientation of exsolved kirschsteinite in an olivine grain has been made. Weak reflections of exsolved kirschsteinite share common crystallographic orientation with the host olivine. The cell dimensions of the exsolved phase (a - 4.87 plus or minus 0.05A, b - 11.14 plus or minus 0.10A, c - 6.36 plus or minus 0.05A) and intensities were in well accord with those of kirschsteinite previously reported. Oriented section perpendicular to the a axis shows exsolution lamellae in two directions parallel to (031) and (031). The lamellae are up to 10 microns in width and spacings between them are usually 50-100 microns.

Mikouchi, Takashi↗
NASA NTRS1990

Photoelectrochemical fabrication of spectroscopic diffraction gratings, phase 2

This program was directed toward the production of Echelle diffraction gratings by a light-driven, electrochemical etching technique (photoelectrochemical etching). Etching is carried out in single crystal materials, and the differential rate of etching of the different crystallographic planes used to define the groove profiles. Etching of V-groove profiles was first discovered by us during the first phase of this project, which was initially conceived as a general exploration of photoelectrochemical etching techniques for grating fabrication. This highly controllable V-groove etching process was considered to be of high significance for producing low pitch Echelles, and provided the basis for a more extensive Phase 2 investigation.

Rauh, R. David↗
NASA NTRS1994

A crystallographic model for hydrous wadsleyite (Beta-Mg2SiO4)

Wadsleyite (beta-Mg2SiO4) is believed to be the most abundant phase in the Earth between depths of 400 and about 525km. Because of the unusual crystal chemistry, Smyth suggested that this phase might be a significant host for hydrogen in the transition zone. Indeed, of the nominally anhydrous phases believed to make up the upper mantle and transition zone none has been reported with a greater H content than wadsleyite. Young et al, report the synthesis of hydrous, Fe-bearing wadsleyite with up to 60,000 H per 10(exp 6) Si. Using ionic constraints and maximal subgroup symmetry, a hypothetical, ordered model for hydrous wadsleyite has been created and examined. The model has formula Mg7Si4O14(OH)2, has space group Pmmb, has an ordered vacancy into one of two non-equivalent M2 sites, and contains two different H positions, one on each of the non-equivalent O1 sites. Electrostatic calculations indicate that hydration would relieve the underbonding of O1 as well as the overbonding of the bridging oxygen, O2, so that the hydrous phase may be more stable than the anhydrous phase. This model makes several predictions that may be of significance for the mechanisms and amounts of H that may be stored in the transition zone of the Earth, and by which the model may be tested experimentally.

Smyth, J. R.↗
NASA NTRS1991

CBr4 vapor growth morphologies near the polymorphic transition point. I - Single crystals. II - Crystals with large-angle grain boundaries

High-resolution microscopy and image processing were used to investigate morphological changes in CBr4 single crystals during growth from the vapor at various levels of supersaturation and at temperatures below the compound's polymorphic phase transition. It was found that, as the temperature increased at fixed supersaturations, the corners of the crystals became rounded as a result of thermal roughening; the rounding temperatures were different for crystallographically different corners. A study of CBr4 crystals with large-angle grain boundaries or twin boundaries (extended macrodefects), conducted at the temperature of polymorphic phase transition showed that the phase transition temperature, T(tr) and crystal surface morphology of these crystals depended on the presence or absence of extended macrodefects. Unlike the case of a perfect single crystal, where the T(tr) was about 46.75 C, the phase transition in crystals with extended macrodefects occurred significantly below 46.75.

Xiao, Rong-Fu↗
NASA NTRSDate not supplied

TPSAS-NF1676L-13664-DND

The safety of aerospace vehicles is largely dependent on the ability of modern non-destructive evaluation (NDE) tools to accurately detect structural damage before a critical flaw size is reached. However, existing NDE technologies are inherently limited by the physical response of the materials being inspected making the detection of small cracks or pre-crack damage difficult. One innovative solution to this problem is to create a multifunctional metallic material that can be used in structural applications and contains second phase sensory particles that significantly enhance the ability of conventional NDE techniques to detect incipient damage during use and at regularly scheduled inspections. Ferromagnetic shape-memory alloys (FSMAs) are an ideal material for use as this second phase material as they undergo a uniform and repeatable change in both magnetic properties and crystallographic structure when strained. These changes are more readily detected than small cracks, thereby, allowing for enhanced detection of damage by conventional NDE techniques. In this study, a multifunctional metallic material was produced by embedding the sensory material particles within an aluminum alloy to form a sensory alloy. The NDE response of the FSMA and the sensory alloy during tension/compression and fatigue loading have been investigated. These results suggest that sensory alloys can be utilized for improved on-board structural health monitoring and to improve the accuracy and reduce time for ground-based inspection.

T. A. Wallace↗
NASA NTRS2020

Capturing an Evolving Nebular Environment: A Petrographic and Geochemical Study of a Type A, B & C CAI

Calcium, Aluminum-rich Inclusions (CAIs) were the first formed solids in our Solar System, with mineral assemblages reflecting the first phases predicted to condense out of a hot nebular gas of Solar composition. Geochemical, textural and crystallographic information in CAIs can be used to constrain the temperature, pressure, and composition (e.g., oxygen fugacity) of the gaseous reservoir(s) from which they formed, as well as any secondary (nebular and parent body) processes they underwent. Coordinated geochemical and textural analyses provide information on nebular conditions (i.e., astrophysical environments and dynamics of nebular gas reservoirs) in which these CAIs formed. In order to better understand the evolution of nebular reservoirs at the time of CAI formation, we analyzed a Type A, B and C CAI using Electron Probe Micro-Analyzer (EPMA) and Electron BackScatter Diffraction (EBSD) at NASA Johnson Space Center (JSC).

Comins, M. B.↗
NASA NTRS1976

Structure-property relationships in eutectic composites

The preparation of a composite material of eutectic composition directly from the molten state is investigated. The manufacture of eutectic composites by unidirectional solidification is reviewed, and it is shown how two-phase composite structures of given relative volume fraction can be produced with a range of particle sizes. Crystallographic relationships and the thermal stability of interfaces in controlled eutectic structures are examined, the mechanical behavior of aligned eutectic microstructures is discussed, and characteristics of eutectic composites having mechanical properties of engineering significance are evaluated. Specific properties of the Ni-Nb eutectic alloy are reviewed to demonstrate the effect of structure control (through directional solidification) on the mechanical response of a eutectic composite. It is noted that unidirectionally solidified eutectic composites possess highly aligned and thermally stable microstructures and also exhibit excellent combinations of strength and ductility to very high temperature levels.

Hertzberg, R. W.↗
NASA NTRS2024

A Coordinated Mineralogical and Oxygen Isotopic Study of Refractory Ca-Al-Rich Inclusions

Refractory Ca-Al-rich inclusions (CAIs) in primitive chondritic meteorites represent the oldest solids that formed in our Solar System. Coordinated analyses using multiple ion and electron-beam techniques are vital to fully understand complex nebular and asteroidal processes that CAIs may have experienced in the context of the formation and early evolution of our Solar System. We report the results of a coordinated mineralogical and oxygen isotopic study of unique grossite bearing CAIs from reduced CV (Vigarano type) carbonaceous chondrites using transmission electron microscopy and secondary ion mass spectrometry. Grossite (CaAl 4 O 7 ) occurs in cores of nodules in fine grained CAIs that likely represent aggregates of nebular condensates. In many occurrences, grossite has been partially replaced by hercynite [(Fe,Mg,Zn)Al 2 O 4 ], which displays complex microstructures and compositions, and magnetite nanoparticles. This grossite alteration likely occurred via crystallographically controlled metasomatic reactions with Zn, Fe-rich aqueous fluids on the parent asteroid. The constituent phases of grossite bearing CAIs show heterogeneous oxygen isotopic compositions . That is, grossite and perovskite are 16 O poor and melilite is variably 16 O-depleted in contrast to solar like, 16 O-rich hibonite and spinel. The observed oxygen isotopic distribution is interpreted as a result of mineralogically controlled oxygen isotopic exchange with an 16 O-poor fluid on the parent asteroid. Collectively, we conclude that the presence of limited fluids played an important role in preferential alteration of grossite to hercynite and magnetite and various degrees of 16 O depletion in grossite, perovskite, and melilite during thermal metamorphism on the CV chondrite parent asteroid.

Jangmi Han↗
NASA NTRS2000

Rhenium/Oxygen Interactions at Elevated Temperatures

The oxidation of pure rhenium is examined from 600-1400 C in oxygen/argon mixtures. Linear weight loss kinetics are observed. Gas pressures, flow rates, and temperatures are methodically varied to determine the rate controlling steps. The reaction at 600 and 800 C appears to be controlled by a chemical reaction step at the surface; whereas the higher temperature reactions appear to be controlled by gas phase diffusion of oxygen to the rhenium surface. Attack of the rhenium appears to be along grain boundaries and crystallographic planes.

Jacobson, Nathan↗
NASA NTRS1986

Undercooling and crystallization behaviour of antimony droplets

The droplet emulsion technique is presently used to examine the undercooling and crystallization behavior of pure antimony. Control of droplet size and applied cooling rate allowed maximum undercooling to be extended from 0.08 to 0.23 T(m). A droplet coating was produced by means of emulsification which appears to furnish a favorable crystallographic matching for effective nucleation catalysis of a metastable simple cubic structure. Thermal analysis shows the melting temperature of the single cubic phase to be about 625 C.

Graves, J. A.↗
NASA NTRS2009

Thermal Decomposition of an Impure (Roxbury) Siderite: Relevance to the Presence of Chemically Pure Magnetite Crystals in ALH84001 Carbonate Disks

The question of the origin of nanophase magnetite in Martian meteorite ALH84001 has been widely debated for nearly a decade. Golden et al. have reported producing nearly chemically pure magnetite from thermal decomposition of chemically impure siderite [(Fe, Mg, Mn)CO3]. This claim is significant for three reasons: first, it has been argued that chemically pure magnetite present in the carbonate disks in Martian meteorite ALH84001 could have formed by the thermal decomposition of the impure carbonate matrix in which they are embedded; second, the chemical purity of magnetite has been previously used to identify biogenic magnetite; and, third, previous studies of thermal decomposition of impure (Mg,Ca,Mn)-siderites, which have been investigated under a wide variety of conditions by numerous researchers, invariably yields a mixed metal oxide phase as the product and not chemically pure magnetite. The explanation for this observation is that these siderites all possess the same crystallographic structure (Calcite; R3c) so solid solutions between these carbonates are readily formed and can be viewed on an atomic scale as two chemically different but structurally similar lattices.

McKay, D.S.↗
NASA NTRS2000

Rhenium-Oxygen Interactions at High Temperatures

The reaction of pure rhenium metal with dilute oxygen/argon mixtures was studied from 600 to 1400 C. Temperature, oxygen pressure, and flow rates were systematically varied to determine the rate-controlling steps. At lower temperatures the oxygen/rhenium chemical reaction is rate limiting; at higher temperatures gas-phase diffusion of oxygen through the static boundary layer is rate limiting. At all temperatures post-reaction microstructures indicate preferential attack along certain crystallographic planes and defects.

Jacobson, Nathan S.↗
NASA NTRS1974

Alkali oxide-tantalum oxide and alkali oxide-niobium oxide ionic conductors

A search was made for new cationic conducting phases in alkali-tantalate and niobate systems. The phase equilibrium diagrams were constructed for the six binary systems Nb2O5-LiNbO3, Nb2O5-NaNbO3, Nb2O5-KNbO3, Ta2O5-NaTaO3, Ta2O5-LiTaO3, and Ta2O5-KTaO3. Various other binary and ternary systems were also examined. Pellets of nineteen phases were evaluated (by the sponsoring agency) by dielectric loss measurements. Attempts were made to grow large crystals of eight different phases. The system Ta2O5-KTaO3 contains at least three phases which showed peaks in dielectric loss vs. temperature. All three contain structures related to the tungsten bronzes with alkali ions in non-stoichiometric crystallographic positions.

Roth, R. S.↗
NASA NTRS2000

Crystallography of Alumina-YAG-Eutectic

Multiple descriptions of the alumina-YAG eutectic crystallography appear in the ceramic literature. The orientation between two phases in a eutectic system has direct impact on residual stress, morphology, microstructural stability, and high temperature mechanical properties. A study to demonstrate that the different crystallographic relationships can be correlated with different growth constraints was undertaken. Fibers produced by Laser-Heated Float Zone (LHFZ) and Edge-defined Film-fed Growth (EFG) were examined. A map of the orientation relationship between Al2O3 and Y3Al5O12 and their relationship to the fiber growth axis as a function of pull rate are presented. Regions in which a single orientation predominates are identified.

Farmer, Serene C.↗
NASA NTRS2004

Solution-Phase Processes of Macromolecular Crystallization

We have proposed, for the tetragonal form of chicken egg lysozyme, that solution phase assembly processes are needed to form the growth units for crystal nucleation and growth. The starting point for the self-association process is the monomeric protein, and the final crystallographic symmetry is defined by the initial dimerization interactions of the monomers and subsequent n-mers formed, which in turn are a function of the crystallization conditions. It has been suggested that multimeric proteins generally incorporate the underlying multimers symmetry into the final crystallographic symmetry. We posed the question of what happens to a protein that is known to grow as an n-mer when it is placed in solution conditions where it is monomeric. The trypsin-treated, or cut, form of the protein canavalin (CCAN) has been shown to nucleate and grow crystals as a trimer from neutral to slightly acidic solutions. Under these conditions the solution is composed almost wholly of trimers. The insoluble protein can be readily dissolved by weakly basic solution, which results in a solution that is monomeric. There are three possible outcomes to an attempt at crystallization of the protein under monomeric (high pH) conditions: 1) we will obtain the same crystals as under trimer conditions, but at different protein concentrations governed by the self association equilibria; 2) we will obtain crystals having a different symmetry, based upon a monomeric growth unit; 3) we will not obtain crystals. Obtaining the first result would be indicative that the solution-phase self-association process is critical to the crystal nucleation and growth process. The second result would be less clear, as it may also reflect a pH-dependent shift in the trimer-trimer molecular interactions. The third result, particularly for experiments in the transition pH's between trimeric and monomeric CCAN, would indicate that the monomer does not crystallize, and that solution phase self association is not part of the crystal nucleation and growth path. Results are presented for crystallization experiments of CCAN over the pH 6.8 to 9.6 range.

Pusey, Marc L.↗
NASA NTRS1991

Tridymite and maghemite formation in an Fe-SiO smoke

Grains produced in porous Fe-SiO smoke are analyzed by means of electron microscopy to determine their crystallographical, morphological, and chemical properties. The nucleation of metal oxide condensates takes place as the vapor evolves in a condensation-flow apparatus, initially producing simple crystalline phases. Fe nucleation follows, and the subsequent heterogeneous nucleation of quenched mixed high-Fe silica grains exhibits associated Fe-depletion, eventually producing pure silica grains. The coalescence exhibited by the pure silica grains is compatible with the higher surface energy found in the pure silica phase. During coagulation the grains melt and anneal to a chemically pure mixture of alpha- and beta-tridymite, and the precipitation of amorphous silica material is observed. The settling of grains in evolving solar nebula is theorized to be related to the stickiness of this material, and maghemite is suggested to contribute to the Fe/Si fractionation in solar nebula.

Rietmeijer, F. J. M.↗
NASA NTRS2002

AFM Studies of Salt Concentration Effects on the (110) Surface Structure of Tetragonal Lysozyme Crystals

Previous high resolution AFM studies of the (110) surface of tetragonal chicken egg white lysozyme crystals had shown that only one of two possible molecular surfaces is present, those constituting the completed 43 helices. These suggested that the crystal growth process was by the solution-phase assembly of the growth units, which then attach to the surface. However, the best fit for the imaged surfaces, vs. those predicted based upon the bulk crystallographic coordinates, were obtained when the packing about the 43 helices was "tightened up", while maintaining the underlying crystallographic unit cell spacing. This results in a widening of the gap between adjacent helices, and the top- most layer(s) may no longer be in contact. We postulated that the tightened packing about the helices is a result of the high salt concentrations in the bulk solution, used to crystallize the protein, driving hydrophobic interactions. Once the crystal surface is sufficiently buried by subsequent growth layers the ratio of salt to protein molecules decreases and the helices relax to their bulk crystallographic coordinates. The crystal surface helix structure is thus a reflection of the solution structure, and the tightness of the packing about the 43 helices would be a function of the bulk salt concentration. AFM images of the (110) surface of tetragonal lysozyme crystals grown under low (2%) and high (5%) NaCl concentrations reveal differences in the packing about the 43 helices consistent with the above proposal.

Pusey, Marc Lee↗