Results for “Cu dispersion” — Page 3

NASA NTRS2004

Reactive Brazing of Carbon-Carbon Composites to Titanium

The Ti-metal/C-C composite joints were formed by reactive brazing with three commercial brazes, namely, Cu-ABA, TiCuNi, and TiCuSil. The joint microstructures were examined using optical microscopy, and scanning electron microscopy (SEM) coupled with energy dispersive spectrometry (EDS). The results of the microstructure analysis indicate solute redistribution across the joint and possible metallurgical bond formation via interdiffusion, which led to good wetting and spreading.

Shpargel, Tarah↗

NASA NTRSDate not supplied

In-Situ Alloying of GRCop-42 via Additive Manufacturing: Precipitate Analysis

GRCop-42, a Cu-4at% Cr-2at% Nb alloy, was designed as a high temperature, high strength, high heat flux material for rocket engine combustion chamber liners by NASA Glenn Research Center. In situ alloying of GRCop-42 (ISGRCop-42) using powder bed fusion (PBF) additive manufacturing (AM) takes elemental powders of Cu, Cr, and Nb to be introduced into the PBF environment and develop the GRCop alloy while simultaneously building an AM component. Elemental powders were milled together prior to printing in an effort to facilitate the alloying process. Success of the in situ alloying process may provide lower cost, faster lead times, alloying optimization, and more design freedom in the development of regeneratively-cooled rocket propulsion systems. Evaluation of the ISGRCop-42 was conducted using a phase extraction procedure to isolate the Cr2Nb precipitates from the pure Cu matrix. The isolated precipitates were then examined using x-ray powder diffraction (XRD), scanning electron microscopy (SEM), and energy dispersion spectroscopy (EDS). It was found that ISGRCop-42 successfully and repeatedly formed Cr2Nb at a yield as high as 89% of potential Cr2Nb. Further, it was identified that the preparation of the powder was the most influential factor in alloying success, and the second most influential factor was the laser power.

In Situ alloying↗

NASA NTRS1978

An interstellar cloud density from Copernicus observations of CO in the spectrum of Zeta Ophiuchi

Interstellar CO absorption bands in Copernicus spectra of Zeta Oph have been studied. Absorption profiles, computed under the assumption that excitation is due to collisions with H2 molecules and interaction with the 3-K background radiation field, were fitted to the reduced data of nine bands. When a gas kinetic temperature of 56 K is assumed, the best-fit condition implies a hydrogen-nucleus density of 120 per cu cm, a CO column density of 1.2 by 10 to the 15th power per sq cm, and a radial-velocity dispersion of 0.9 km/s. The relevance of these results to existing ideas concerning the Zeta Oph interstellar clouds is discussed. It is suggested that the strongest interstellar component is not circumstellar in origin but is instead part of a supernova remnant. Simple calculations are made to establish the plausibility of the supernova-remnant identification. This suggestion is also supported by Heiles's (1976) 21-cm pictures.

Smith, A. M.↗

NASA NTRSDate not supplied

Mechanisms of Interfacial Mixing in the Blown Powder Deposition of Inconel 625 to Copper Alloy for Liquid Rocket Engine Applications

There is an increasing need for functional materials to support high heat flux applications and optimize weight by using bimetallic additive manufacturing (AM). While one promising fabrication technology is the use of blown powder directed energy deposition (DED) AM, challenges remain with bi-metallic combinations. Prominent among these challenges is the need to understand mixing of materials at the bimetallic interface for forming stronger, more durable and reliable joints to extend the versatility of AM into critical applications. One application is the manufacturing of combustion chambers with copper-alloy liners and Superalloy structural jackets. In this application, material combinations are selected for effective heat dissipation, using copper, and retention of strength at high temperatures using Inconel 625. Currently, the dominant problem with this configuration is the highly variable strength of the interface and its correlation with deposition parameters. In this study, samples were fabricated at several vendors with Inconel 625 deposited onto wrought C-18150 (Cu-Cr-Zr) to form a bimetallic interface. Characterization of the interfaces were achieved through optical and electron microscopy, mechanical testing of mini tensile specimens, and electron dispersion spectroscopy to understand diffusion and bulk mixing behaviors at the joint. A theoretical framework was constructed in the context of solidification and mixing mechanisms to explain the resulting differences in the interface. This qualitative approach utilized a fluid dynamics perspective to sum the order of magnitudes of the various acting forces on the weld pool during deposition to predict convection trends based off known parameters. The predicted trends for each vendor are compared to obtain a better understanding of how mixing in the molten pool varied based on deposition parameters.

Additive Manufacturing↗

NASA NTRS2008

Bonding and Integration of C-C Composite to Cu-Clad-Molybdenum for Thermal Management Applications

Two- and three-dimensional carbon-carbon composites with either resin-derived matrix or CVI matrix were joined to Cu-clad-Mo using active Ag-Cu braze alloys for thermal management applications. The joint microstructure and composition were examined using Field-Emission Scanning Electron Microscopy and Energy-Dispersive Spectroscopy, and the joint hardness was characterized using the Knoop microhardness testing. Observations on the infiltration of the composite with molten braze, dissolution of metal substrate, and solute segregation at the C-C surface have been discussed. The thermal response of the integrated assembly is also briefly discussed.

Asthana, R.↗

NASA NTRS1983

Rotational CARS application to simultaneous and multiple-point temperature and concentration determination in a turbulent flow

Coherent anti-Stokes Raman scattering (CARS) from the pure rotational Raman lines of N2 is employed to measure the instantaneous (approximately 10 ns) rotational temperature of N2 gas at room temperature and below with good spatial resolution (0.2 x 0.2 x 3.0 cu mm). A broad bandwidth dye laser is used to obtain the entire rotational spectrum from a single laser pulse; the CARS signal is then dispersed by a spectrograph and recorded on an optical multichannel analyzer. A best fit temperature is found in several seconds with the aid of a computer for each experimental spectrum by a least squares comparison with calculated spectra. The model used to calculate the theoretical spectra incorporates the temperature and pressure dependence of the pressure-broadened rotational Raman lines, includes the nonresonant background susceptibility, and assumes that the pump laser has a finite linewidth. Temperatures are fit to experimental spectra recorded over the temperature range of 135 to 296 K, and over the pressure range of .13 to 15.3 atm.

Snow, J. B.↗

NASA NTRS1986

Microstructure/mechanical property relationships for various thermal treatments of Al-Cu-Mg-X PM aluminum alloys

The thermal response and aging behavior of three 2XXX-series powder metallurgy aluminum alloys have been investigated, using Rockwell B hardness measurements, optical and electron microscopy, and energy-dispersive chemical analysis, in order to correlate microstructure with measured mechanical properties. Results of the thermal response study indicated that an increased solution heat treatment temperature was effective in resolutionizing large primary constituents in the alloy bearing more copper but had no apparent effect on the microconstituents of the other two. Aging studies conducted at room temperature and at 120, 150, and 180 C for times ranging up to 60 days indicated that classic aging response curves, as determined by hardness measurements, occurred at lower aging temperatures than were previously studied for these alloys, as well as at lower aging temperatures than are commonly used for ingot metallurgy alloys of similar compositions. Microstructural examination and fracture surface analysis of peak-aged tension specimens indicated that the highest tensile strengths are associated with extremely fine and homogeneous distributions of theta-prime or S-prime phases combined with low levels of both large constituent particles and dispersoids. Examination of the results suggest that refined solution heat treatments and lower aging temperatures may be necessary to achieve optimum mechanical properties for these 2XXX series alloys.

Blackburn, L. B.↗

NASA NTRS2018

Development of New Rocket Engine Liner Materials Based on Copper Alloys with Diamond Particle Additions

Novel copper-diamond materials containing particulate dispersions of diamond within a copper alloy matrix have been produced as next-generation rocket engine combustion chamber liner materials. These Copper-Diamond (Cu-D) composite materials have significantly higher thermal conductivity than conventional liner materials and have the potential to increase the engine performance significantly. Liner fabrication techniques include hot pressing and spark plasma sintering (SPS), which are capable of scale up to full-size production parts. The materials have been evaluated for thermal cycling resistance and ease of manufacturing. The results indicate great promise of these materials and associated economics to replace state-of-the-art combustion chamber liner materials such as GRCop-84 and NARloy-Z. Combustion chamber fabrication processes are also discussed, including SPS and additive manufacturing.

Bhat, Biliyar N.↗

NASA NTRS2013

Copper-Multiwall Carbon Nanotubes and Copper-Diamond Composites for Advanced Rocket Engines

This paper reports on the research effort to improve the thermal conductivity of the copper-based alloy NARloy-Z (Cu-3 wt.%Ag-0.5 wt.% Zr), the state-of-the-art alloy used to make combustion chamber liners in regeneratively-cooled liquid rocket engines, using nanotechnology. The approach was to embed high thermal conductivity multiwall carbon nanotubes (MWCNTs) and diamond (D) particles in the NARloy-Z matrix using powder metallurgy techniques. The thermal conductivity of MWCNTs and D have been reported to be 5 to 10 times that of NARloy-Z. Hence, 10 to 20 vol. % MWCNT finely dispersed in NARloy-Z matrix could nearly double the thermal conductivity, provided there is a good thermal bond between MWCNTs and copper matrix. Quantum mechanics-based modeling showed that zirconium (Zr) in NARloy-Z should form ZrC at the MWCNT-Cu interface and provide a good thermal bond. In this study, NARloy-Z powder was blended with MWCNTs in a ball mill, and the resulting mixture was consolidated under high pressure and temperature using Field Assisted Sintering Technology (FAST). Microstructural analysis showed that the MWCNTs, which were provided as tangles of MWCNTs by the manufacturer, did not detangle well during blending and formed clumps at the prior particle boundaries. The composites made form these powders showed lower thermal conductivity than the base NARloy-Z. To eliminate the observed physical agglomeration, tangled multiwall MWCNTs were separated by acid treatment and electroless plated with a thin layer of chromium to keep them separated during further processing. Separately, the thermal conductivities of MWCNTs used in this work were measured, and the results showed very low values, a major factor in the low thermal conductivity of the composite. On the other hand, D particles embedded in NARloy-Z matrix showed much improved thermal conductivity. Elemental analysis showed migration of Zr to the NARloy-Z-D interface to form ZrC, which appeared to provide a low contact thermal resistance. These results are consistent with the quantum mechanics-based model predictions. NARloy-Z-D composites have relatively high thermal conductivities and are promising for further development.

Bhat, Biliyar N.↗

NASA NTRS2013

Copper Multiwall Carbon Nanotubes and Copper-Diamond Composites for Advanced Rocket Engines

This paper reports on the research effort to improve the thermal conductivity of the copper-based alloy NARloy-Z (Cu-3 wt.%Ag-0.5 wt.% Zr), the state-of-the-art alloy used to make combustion chamber liners in regeneratively-cooled liquid rocket engines, using nanotechnology. The approach was to embed high thermal conductivity multiwall carbon nanotubes (MWCNTs) and diamond (D) particles in the NARloy-Z matrix using powder metallurgy techniques. The thermal conductivity of MWCNTs and D have been reported to be 5 to 10 times that of NARloy-Z. Hence, 10 to 20 vol. % MWCNT finely dispersed in NARloy-Z matrix could nearly double the thermal conductivity, provided there is a good thermal bond between MWCNTs and copper matrix. Quantum mechanics-based modeling showed that zirconium (Zr) in NARloy-Z should form ZrC at the MWCNT-Cu interface and provide a good thermal bond. In this study, NARloy-Z powder was blended with MWCNTs in a ball mill, and the resulting mixture was consolidated under high pressure and temperature using Field Assisted Sintering Technology (FAST). Microstructural analysis showed that the MWCNTs, which were provided as tangles of MWCNTs by the manufacturer, did not detangle well during blending and formed clumps at the prior particle boundaries. The composites made form these powders showed lower thermal conductivity than the base NARloy-Z. To eliminate the observed physical agglomeration, tangled multiwall MWCNTs were separated by acid treatment and electroless plated with a thin layer of chromium to keep them separated during further processing. Separately, the thermal conductivities of MWCNTs used in this work were measured, and the results showed very low values, a major factor in the low thermal conductivity of the composite. On the other hand, D particles embedded in NARloy-Z matrix showed much improved thermal conductivity. Elemental analysis showed migration of Zr to the NARloy-Z-D interface to form ZrC, which appeared to provide a low contact thermal resistance. These results are consistent with the quantum mechanics-based model predictions. NARloy-Z-D composites have relatively high thermal conductivities and are promising for further development.

Bhat, Biliyar N.↗

NASA NTRS1991

Sintering of two phase lamellar microstructures

The effect of an inert phase on neck growth rates during sintering of lamellar structures is described. Sintering diagrams are constructed for an aggregate of two-phase Cu spheres with lamellar microstructure containing an inert phase. It is shown that the regions corresponding to lattice diffusion domination shrink due to the inert phase presence. As the dispersion becomes finer, the alterations in the map become substantial.

Courtney, T. H.↗

NASA NTRS2008

Comparison of the Isothermal Oxidation Behavior of As-Cast Cu-17 Percent Cr and Cu-17 Percent Cr-5 Percent Al: Scale Microstructures - Part 2

The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. Details of the oxidation kinetics of these alloys were discussed in Part I. This paper analyzes the microstructures of the scale and its composition in an attempt to elucidate the oxidation mechanisms in these alloys. The scales formed on Cu-17%Cr specimens oxidized between 773 and 973 K consisted of external CuO and subsurface Cu2O layers. The total thickness of these scales varied from about 10 m at 773 K to about 450 m at 973 K. In contrast, thin scales formed on Cu-17%Cr-5%Al alloys oxidized between 773 and 1173 K. The exact nature of these scales could not be determined by x-ray diffraction but energy dispersive spectroscopy analyses were used to construct a scale composition map. Phenomenological oxidation mechanisms are proposed for the two alloys.

Raj, S. V.↗

NASA NTRS2008

Comparison of the Isothermal Oxidation Behavior of As-Cast Cu-17 Percent Cr and Cu-17 Percent Cr-5 Percent Al Part II: Scale Microstructures

The isothermal oxidation kinetics of as-cast Cu-17%Cr and Cu-17%Cr-5%Al in air were studied between 773 and 1173 K under atmospheric pressure. Details of the oxidation kinetics of these alloys were discussed in Part I. This paper analyzes the microstructures of the scale and its composition in an attempt to elucidate the oxidation mechanisms in these alloys. The scales formed on Cu-17%Cr specimens oxidized between 773 and 973 K consisted of external CuO and subsurface Cu2O layers. The total thickness of these scales varied from about 10 m at 773 K to about 450 m at 973 K. In contrast, thin scales formed on Cu-17%Cr-5%Al alloys oxidized between 773 and 1173 K. The exact nature of these scales could not be determined by x-ray diffraction but energy dispersive spectroscopy analyses were used to construct a scale composition map. Phenomenological oxidation mechanisms are proposed for the two alloys.

Raj, Sai V.↗

NASA NTRS1990

The Mechanisms of Dispersion Strengthening and Fracture in Al-based XD (TM) Alloys

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength, and the fracture toughness of metal matrix composites of both pure aluminum and Al(4 percent)Cu(1.5 percent)Mg with 0 to 15 vol percent TiB2 were examined. Higher TiB2 volume fractions increased the tensile yield strength both at room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. The fracture toughness of the Al(4 percent)Cu(1.5 percent)Mg alloys decreased rapidly with TiB2 additions of 0 to 5 vol percent and more slowly with TiB2 additions of 5 to 15 vol percent. Fracture toughness appears to be independent of TiB2 particle size. The isothermal-aging response of the precipitation strengthened Al(4 percent)Cu(1.5 percent)Mg alloys was not altered by the presence of TiB2.

Aiken, R. M., Jr.↗

NASA NTRS2006

Effect of Composite Substrates on the Mechanical Behavior of Brazed Joints in Metal-Composite System

Advanced composite components are being considered for a wide variety of demanding applications in aerospace, space exploration, and ground based systems. A number of these applications require robust integration technologies to join dissimilar materials (metalcomposites) into complex structural components. In this study, three types of composites (C-C, C-SiC, and SiC-SiC) were vacuum brazed to commercially pure Ti using the active metal braze alloy Cusil-ABA (63Ag-35.3Cu-1.75Ti). Composite substrates with as fabricated and polished surfaces were used for brazing. The microstructure and composition of the joint, examined using scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS), showed sound metallurgical bonding in all systems. The butt strap tensile (BST) test was performed on bonded specimens at room and elevated temperatures. Effect of substrate composition, interlaminar properties, and surface roughness on the mechanical properties and failure behavior of joints will be discussed.

Singh, M.↗

NASA NTRS1990

The mechanisms of dispersion strengthening and fracture in Al-based XD(tm) alloys, part 1

The influence of reinforcement size, volume fraction, and matrix deformation behavior on room and elevated temperature strength; the fracture toughness; and the fatigue crack growth rate of metal matrix composites of Al-4(pct)Cu-1.5(pct)Mg with TiB2 were examined. The influence of reinforcement volume fraction was also examined for pure aluminum with TiB2. Higher TiB2 volume fractions increased the tensile yield strength at both room and elevated temperatures, and reduced the elongation to fracture. Tensile tests also indicate that small particles provided a greater increase in strength for a given volume fraction than larger particles, whereas elongation to fracture appeared to be insensitive to reinforcement size. Interparticle spacing appears to be the factor that controls the strength of these alloys, with the exact nature of the dependence relying on the nature of dislocation slip in the matrix (planar vs. diffuse). The isothermal aging response of the precipitation strengthened Al-4(pct)Cu-1.5(pct)Mg alloys was not accelerated by the presence of TiB2. Cold work prior to artificial aging created additional geometrically necessary dislocations which serve as heterogeneous nucleation sites leading to accelerated aging, a finer precipitate size, and an increase in the strength of the alloy.

Aikin, R. M., Jr.↗

NASA NTRS1985

Inference of equatorial field-line-integrated electron density values using whistlers

The nighttime electron density integrated along a magnetic field line at very small L-values (about 1.06) is inferred by comparing whistler dispersions, measured from a sounding rocket, with model ionospheric calculations. At a local time of 0500 LT, the electron density in the F-layer valley was found to be about 1000 per cu cm. It is suggested that this technique can be applied to earlier times in the local evening to determine ionospheric conditions which benefit the growth of low-latitude plasma instabilities.

Anderson, D. N.↗

NASA NTRS1993

Residual strain gradient determination in metal matrix composites by synchrotron X-ray energy dispersive diffraction

An X-ray technique for the measurement of internal residual strain gradients near the continuous reinforcements of metal matrix composites has been investigated. The technique utilizes high intensity white X-ray radiation from a synchrotron radiation source to obtain energy spectra from small (0.001 cu mm) volumes deep within composite samples. The viability of the technique was tested using a model system with 800 micron Al203 fibers and a commercial purity titanium matrix. Good agreement was observed between the measured residual radial and hoop strain gradients and those estimated from a simple elastic concentric cylinders model. The technique was then used to assess the strains near (SCS-6) silicon carbide fibers in a Ti-14Al-21Nb matrix after consolidation processing. Reasonable agreement between measured and calculated strains was seen provided the probe volume was located 50 microns or more from the fiber/matrix interface.

Kuntz, Todd A.↗