Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cu impurities”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Sticking Coefficients of Fusion Reactor Impurities from Molecular Dynamics Simulations for the Design of Cryopumps

A cryopump can be utilized as an impurity removal component of a direct internal recirculation (DIR) system for the fusion fuel cycle. The DIR facilitates a low fuel inventory by continuously pumping unburnt fuel while removing impurities from the fusion exhaust stream. A cryopump can target multiple impurity species by maintaining a temperature lower than the gas triple-point temperature that promotes desublimation. The desublimation/condensation of gases in cryopumps can be characterized by the sticking coefficient, which is defined as the probability for a gas particle to stick to a (cryo-)surface upon collision. The sticking coefficient is one of the important design/operation parameters for cryopumps, and it depends on a variety of surface and gas properties. Here, in this study, molecular dynamics simulations were utilized to estimate the sticking coefficients of typical fusion gas impurity species N 2 , CO 2 , and CH 4 over a Cu surface for a range of gas temperatures and surface coverages. The molecular dynamics study showed that the sticking coefficients for gases decrease with an increase in gas temperature. The presence of a single full monolayer of condensate on the metallic surface showed an adverse effect on the sticking of gases; however the sticking improved with two full monolayers of condensate on the surface. The sticking of gases over the mixed condensate on a surface was more favorable than the condensate of the same species for N 2 and CH 4 , with an exception for CO 2 , which showed a decrease in sticking over the mixed condensate.

cryopump↗
DOE OSTI2024

The LLNL rabbit: determination of trace element levels in polyethylene

Rabbit facilities are systems that pneumatically transport a sample carrier (known as a rabbit) to and from a radiation source. However, trace impurities in the polyethylene (PE) rabbit may interfere with measurements of short-lived isotopes. Activated impurities with short half-lives as 28 Al interfere with the fission product γ-ray, therefore the rabbit cannot be measured immediately. Neutron activation analysis was performed on various PE samples obtained from different manufacturers and the highest quality PE was used to fabricate a high-purity PE rabbit. Here, the impurities identified in the PE study were 27 Al, 48 Ca, 37 Cl, 50 Cr, 65 Cu, 127 I, 26 Mg, 55 Mn, and 30 Si.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Microscopic examination of rf-cavity-quality niobium films through local nonlinear microwave response

The performance of superconducting radio-frequency (SRF) cavities is sometimes limited by local defects. To investigate the rf properties of these local defects, especially those that nucleate rf magnetic vortices, a near-field magnetic microwave microscope is employed. Local third-harmonic response ( P 3 f ) and its temperature dependence and rf power dependence are measured for one Nb / Cu film grown by direct current magnetron sputtering (DCMS) and six Nb / Cu films grown by high-power impulse magnetron sputtering (HiPIMS) with systematic variation of deposition conditions. Five out of the six HiPIMS Nb / Cu films show a strong third-harmonic response that is likely coming from rf vortex nucleation due to a low- T c surface defect with a transition temperature between 6.3 and 6.8 K, suggesting that this defect is a generic feature of air-exposed HiPIMS Nb / Cu films. A phenomenological model of surface-defect grain boundaries hosting a low- T c impurity phase is introduced and studied with time-dependent Ginzburg-Landau (TDGL) simulations of probe-sample interaction to better understand the measured third-harmonic response. The simulation results show that the third-harmonic response of rf vortex nucleation caused by surface defects exhibits the same general features as the data, including peaks in third-harmonic response with temperature, and their shift and broadening with higher microwave amplitude. We find that the parameters of the phenomenological model (the density of surface defects that nucleate rf vortices and the depth an rf vortex travels through these surface defects) vary systematically with film deposition conditions. From the point of view of these two properties, the Nb / Cu film that is most effective at reducing the nucleation of rf vortices associated with surface defects can be identified. Published by the American Physical Society 2024

Wang, Chung-Yang (ORCID:0000000184299633)↗
DOE OSTI2026

Influence of Transition Metal Ion Contaminants on the Performance of Amine-Based Solid Sorbents in Direct Air Capture

Amine-functionalized solid sorbents are a class of sorbent materials proposed for direct air capture (DAC) of CO 2 , yet their long-term performance is susceptible to degradation under realistic operating conditions. Many amines are not thermodynamically stable in air, and amine sorbents oxidize while in use during DAC temperature swing adsorption processes. In this study, we investigate the role of transition metal ion contaminants, specifically Cu 2+ , Fe 2+ , and Ni 2+ , on the oxidative degradation of poly(ethylenimine) (PEI)-impregnated SBA-15 sorbents. By introducing metal ions via different modes mimicking both synthesis-related impurities and impurities derived from environmental exposure, we systematically evaluate sorbent stability after exposure to dry air at an elevated temperature. Thermogravimetric CO 2 uptake measurements reveal that even trace levels of Cu and Fe (as low as ∼4 ppm) can lead to measurable sorbent deactivation after oxidative aging, despite negligible loss in the performance of the control samples. In situ infrared, UV–vis, and X-ray photoelectron spectroscopies indicate that these metals catalyze radical-driven oxidation pathways, altering the chemical structure of the sorbent and accelerating degradation. Our findings underscore the need to account for trace metal contamination during DAC sorbent synthesis and deployment and highlight the importance of environmental contamination pathways.

CO2 capture↗
DOE OSTI2026

Enhancing microsegregation during rapid directional solidification through ternary microalloying

The nano-cellular dendritic microstructure formed during rapid directional solidification in powder bed fusion additive manufacturing creates unique properties such as simultaneous improvement in strength and ductility. However, process control of microsegregation features remains challenging due to low sensitivity of critical solidification mechanisms to process parameters. This study leverages microalloying to achieve large changes in dendrite composition, microstructure, and interdendritic zone width during laser powder bed fusion without modifying process parameters. CALPHAD simulations predict that the addition of Zr significantly steepens the solidus line of the dilute Cu-Cr alloy system, leading to enhanced Cr rejection into the melt and greater than 95% reduction in solubility of Cr in the solidified Cu matrix. Experimental validation using time-of-flight secondary ion mass spectrometry and Kelvin probe force microscopy reveals that the ternary alloy containing 0.01 wt% Zr exhibited wider interdendritic regions compared to the binary, a significantly higher number of Cr-rich particles within interdendritic regions, near-complete ejection of oxygen impurities from the matrix, and greater nanoscale work function contrast. These features indicate more aggressive Cr segregation in the presence of Zr and a purer Cu matrix and provide a potentially robust method for engineering the nano-cellular dendritic solidification microstructure.

CALPHAD↗
DOE OSTI2024

Electron Glass Phase with Resilient Zhang-Rice Singlets in LiCu 3 ⁢O 3

LiCu 3 ⁢O 3 is an antiferromagnetic mixed valence cuprate where trilayers of edge-sharing Cu(II)O (3⁢d 9 ) are sandwiched in between planes of Cu(I) (3⁢d 10 ) ions, with Li stochastically substituting Cu(II). Angle-resolved photoemission spectroscopy (ARPES) and density functional theory reveal two insulating electronic subsystems that are segregated in spite of sharing common oxygen atoms: a Cu d z 2 /O p z derived valence band (VB) dispersing on the Cu(I) plane, and a Cu 3⁢d x 2 -y 2 /O 2⁢p x,y derived Zhang-Rice singlet (ZRS) band dispersing on the Cu(II)O planes. First-principle analysis shows the Li substitution to stabilize the insulating ground state, but only if antiferromagnetic correlations are present. Li further induces substitutional disorder and a 2D electron glass behavior in charge transport, reflected in a large 530 meV Coulomb gap and a linear suppression of VB spectral weight at E F that is observed by ARPES. Surprisingly, the disorder leaves the Cu(II)-derived ZRS largely unaffected. Finally, this indicates a local segregation of Li and Cu atoms onto the two separate corner-sharing Cu⁡(II)⁢O 2 sub-lattices of the edge-sharing Cu(II)O planes, and highlights the ubiquitous resilience of the entangled two hole ZRS entity against impurity scattering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Plasmon excitations in chemically heterogeneous nanoarrays

The capability of collective excitations, such as localized surface plasmon resonances, to produce a versatile spectrum of optical phenomena is governed by the interactions within the collective and single-particle responses in the finite system. In many practical instances, plasmonic metallic nanoparticles and arrays are either topologically or chemically heterogeneous, which affects both the constituent transitions and their interactions. Here, the formation of collective excitations in weakly Cu- and Pd-doped Au nanoarrays is described using time-dependent density functional theory. The additional impurity-induced modes in the optical response can be thought to result from intricate interactions between separated excitations or transitions. In this work, we investigate the heterogeneity at the impurity level, the symmetry aspects related to the impurity position, and the influence of the impurity position on the confinement phenomena. The chemically rich and symmetry-dependent quantum mechanical effects are analyzed with transition contribution maps demonstrating the possibility to develop nanostructures with more controlled collective properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Conversion of real-world aluminum scrap streams into high-performance Al–Mg–Si–Cu automotive alloys using shear assisted processing and extrusion

The conversion of post-consumer aluminum (Al) scrap into usable Al alloys without adding primary Al is challenging because of excess impurities. In this work, >99% post-consumer Twitch, used beverage cans (UBCs), and remelt scrap ingots (RSIs) were used as feedstock materials. As-cast and solution heat-treated feedstock billets were extruded using Shear Assisted Processing and Extrusion (ShAPE) at ~510°C, followed by press quenching. To explore the development of the microstructure, texture, and underlying mechanisms and how they contribute to the overall strengthening in as-extruded and artificially aged samples, scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) were used to collect microstructure and texture data. The enhanced strength and ductility were corroborated with the microstructural features and crystallographic texture. Simple shear $\textrm{A}/\bar{\textrm{A}}$, $\textrm{A}_1^*/\textrm{A} _2^*$ texture components along with weak $\textrm{C}$ and $\textrm{B}/\bar{\textrm{B}}$ texture components were formed during extrusion; the texture was strengthened after heat treatment. The refined second-phase particles helped to retain the deformed microstructure and texture. The contributions of dislocation and precipitate strengthening were maximized when billets were solution-heat-treated prior to extrusion. This is attributed to the formation of effective supersaturated solid solutions during the ShAPE process, which precipitate out during the peak age treatment. Overall, the highest yield strength of 305 MPa, ultimate tensile strength of 350 MPa, and elongation of 12% were achieved in artificially aged samples, which are comparable to those of Al 6082-T6.

Al alloy↗
DOE OSTI2024

Precision Structure Engineering of High-Entropy Oxides under Ambient Conditions

High-entropy oxides (HEOs) have unveiled a unique frontier in the realm of heterogeneous catalysis, taking advantage of the entropic effect and increased complexities to deliver ultrahigh stability and large tuning capability. However, current HEO synthesis mainly relies on high-temperature annealing approaches affording HEOs possessing no or low surface area, inferior active site exposure efficiency, and low controllability over the structure tuning. The grand challenge lies in producing high-quality HEO catalysts with high active site utilization efficiency, which relies on precision structure engineering, preferably under mild conditions. In this work, an in situ lattice engineering approach was developed to afford a supported HEO catalyst under ambient conditions. The HEO compositions (CuCoFeNiMnO x ) were uniformly integrated into the lattice of CeO 2 driven by cavitation-induced nucleation being generated via ultrasonication. The as-afforded catalysts were featured by high surface area, atomically dispersed HEO compositions, active redox properties, abundant oxygen vacancies (O V ), antiagglomeration, and high phase stability under harsh conditions. Compared with the ex situ introduction of HEO on the surface, the in situ method provides dual benefits to maintain the dispersity of HEO via entropic and lattice confinement effects. Engineering the complex HEO within the lattice of fluorite-structured CeO 2 also yields abundant defects (e.g., O V ) and active metal sites with strong reducing properties (e.g., Ce 3+ and Cu + ), which greatly improves the activity of the lattice oxygen and tunability of the adsorption behavior of the guest molecules, especially in the presence of impurities (e.g., water and propane). The catalytic performance of the supported HEO catalyst in oxidative procedures surpasses the pure dense phase HEO as well as the ex situ-generated catalysts. Further, the synthesis approach being developed in this work, together with the fundamental understanding in structure evolution and reaction mechanism, showcases a facile pathway under ambient conditions to generate stable catalysts capable of maintaining structural robustness in high-temperature conditions while delivering enhanced catalytic performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Imaging and dosimetric characteristics of 67 Cu

In recent years the use of beta-emitting radiopharmaceuticals for cancer therapy has expanded rapidly following development of therapeutics for neuroendocrine tumors, prostate cancer, and other oncologic malignancies. One emerging beta-emitting radioisotope of interest for therapy is 67 Cu (t 1/2 : 2.6 d) due to its chemical equivalency with the widely-established positron-emitting isotope 64 Cu (t 1/2 : 12.7 h). Here we evaluate both the imaging and dosimetric characteristics of 67 Cu, as well as producing the first report of SPECT/CT imaging using 67 Cu. To this end, 67 Cu was produced by photon-induced reactions on isotopically-enriched 68 Zn at the Low-Energy Accelerator Facility (LEAF) of Argonne National Laboratory, followed by bulk separation of metallic 68 Zn by sublimation and radiochemical purification by column chromatography. Gamma spectrometry was performed by efficiency-calibrated high-purity germanium (HPGe) analysis to verify absolute activity calibration and establish radionuclidic purity. Absolute activity measurements corroborated manufacturer-recommended dose-calibrator settings and no radionuclidic impurities were observed. Using the Clinical Trials Network anthropomorphic chest phantom, SPECT/CT images were acquired. Medium Energy (ME) SPECT collimation was found to provide the best image quality from the primary 185 keV gamma emission of 67 Cu. Reconstructed images of 67 Cu were similar in quality to images acquired using 177 Lu. Recovery coefficients were calculated and compared against quantitative images of 99m Tc, 177 Lu, and 64 Cu within the same anthropomorphic chest phantom. Production and clinical imaging of 67 Cu appears feasible, and future studies investigating the therapeutic efficacy of 67 Cu-based radiopharmaceuticals are warranted.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2023

Sequential Recovery of Critical Metals from Leached Liquor of Processed Spent Lithium-Ion Batteries

The processing and extraction of critical metals from black mass is important to battery recycling. Separation and recovery of critical metals (Co, Ni, Li, and Mn) from other metal impurities must yield purified metal salts, while avoiding substantial losses of critical metals. Solvent extraction in batch experiments were conducted using mixed metal sulphates obtained from the leach liquor obtained from spent and shredded lithium-ion batteries. Selective extraction of Mn 2+ , Fe 3+ , Al 3+ and Cu 2+ from simulated and real leached mixed metals solution was carried out using di-2-ethylhexylphophoric acid (D2EPHA) and Cyanex-272 at varying pH. Further experiments with the preferred extractant (D2EPHA) were performed under different conditions: changing the concentration of extractant, organic to aqueous ratio, and varying the diluents. At optimum conditions (40% v/v D2EPHA in kerosene, pH 2.5, O:A = 1:1, 25 °C, and 20 min), 85% Mn 2+ , 98% Al 3+ , 100% Fe 3+ , and 43% Cu 2+ were extracted with losses of only trace amounts (<5.0%) of Co 2+ , Ni 2+ , and Li + . The order of extraction efficiency for the diluents was found to be kerosene > Exxal-10 >>> dichloromethane (CH 2 Cl 2 ) > toluene. Four stages of stripping of metals loaded on D2EPHA were performed as co-extracted metal impurities were selectively stripped, and a purified MnSO 4 solution was produced. Spent extractant was regenerated after Fe 3+ and Al 3+ were completely stripped using 1.0 M oxalic acid (C 2 H 2 O 4 ).

25 ENERGY STORAGE↗
DOE OSTI2021

Computational design of passivants for CdTe grain boundaries

CdTe is the second most-widely deployed photovoltaic (PV) material due to its high efficiency and low manufacturing costs. Currently, polycrystalline CdTe (poly-CdTe) has a record efficiency of similar to 22%, which is still well below the theoretical limit (similar to 30%). Polycrystalline CdTe films that have incorporated Cl or Se show higher efficiency, possibly due to the segregation of these ions to the grain boundaries (GBs), where they may passivate the dangling bonds. However, the efficiency enhancement mechanisms of passivants in CdTe GBs, and the feasibility of employing alternative passivants, have not been well explored. Here, we present a systematic computational study of CdTe GBs with potential passivants, namely S, P, As, Se, and Sb on Te sites, and Na, Mg, Al, Sc, Cu, and Zn on Cd sites. Density functional theory (DFT) calculations were performed on GB dislocation core structures derived from scanning transmission electron microscopy (STEM) images of a model GB (bicrystal). We computed the segregation thermodynamics, electronic density of states, and charge variations near doped CdTe GBs. We find that segregation of impurities to GBs is thermodynamically favorable. For a Te-terminated core, Se, S, and P on Te sites effectively reduce midgap states. For both Cd-and Te-terminated dislocation cores, Sc and Al reduce midgap states when substituted for Cd atoms. Overall, the greatest improvement was achieved with co-doping, i.e. simultaneously substituting Te with Se and substituting Cd with Cu or Al. The elimination of midgap states is predicted to increase the photovoltaic efficiency of CdTe by reducing the recombination at grain boundaries.

14 SOLAR ENERGY↗
DOE OSTI2021

Multimodal X-ray Microscopy: The Kinetics of Cu in CdTe Absorbers

The behavior of solar cells is very often limited by inhomogeneously distributed nanoscale defects. This is the case throughout the entire lifecycle of the solar cell, from the distribution of elements and defects during solar cell growth as well as the charge-collection and recombination during operation, to degradation and failure mechanisms due to impurity diffusion, crack formation, and irradiation- and heat-induced cell damage This has been known for a while in the field of crystalline silicon, but inhomogeneities are far more abundant in polycrystalline materials, and are the limiting factor in thin-film solar cells where grain sizes are often on the order of the diffusion length. We showed that the high penetration of hard X-rays combined with the high sensitivity to elemental distribution, structure, and spatial resolution offers a unique avenue for highly correlative studies at the nanoscale. We presented results on Cu-doped CdTe, where carrier collection is directly correlated to the kinetics of Cu inside the absorber and the particular Cu-phases at the ZnTe/CdTe interface. We complemented the results with modeling using PVRD-FASP and PyCDTS, where the X-ray beam induced profile can be reproduced by the equilibrium defect concentrations proposed by the solvers.

Bertoni, Mariana↗
DOE OSTI2021

High-efficiency catalytic reduction of residual oxygen for purification of carbon dioxide streams from high-pressure oxy-combustion systems

Pressurized oxy-combustion is a promising technology for carbon capture, utilization, and storage. For the captured CO 2 to be used for enhanced oil recovery or stored in geological formations, flue gas impurities, including residual O 2 in the CO 2 stream, must be purified to meet the purity specifications. A catalytic approach to reducing residual O 2 with CH 4 was investigated in this study. Five CoMn- and Cu-based catalysts were synthesized or acquired, and a reverse-flow fixed-bed reactor was used to assess their performance for O 2 removal from a simulated oxy-combustion flue gas at 15 bar. The impacts of the operating parameters on O 2 removal, such as temperature, gas hourly space velocity, O 2 /CH 4 ratio, and gas pressure, were investigated. Among the tested catalysts, the two CoMn catalysts were superior in both activity and selectivity, with the reaction lighting off at about 350 °C and achieving 99% O 2 removal at about 500 °C. Finally, the kinetics of the catalytic reaction is discussed, and the Mars–van Krevelen redox mechanism is deemed valid for describing the reaction pathway for the top-performing CoMn catalysts. The catalytic reaction was determined to be first order in CH 4 and zero order in O 2 under the test conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Optimized purification methods for metallic contaminant removal from directly recycled Li-ion battery cathodes

Metallic contaminants pose a significant challenge to the viability of directly recycling Li-ion batteries. To date, few strategies exist to selectively remove metallic impurities from mixtures of shredded end-of-life material (black mass; BM) without concurrently damaging the structure and electrochemical performance of the target active material. We herein present tailored methods to selectively ionize two major contaminants—Al and Cu—while retaining a representative cathode (LiNi 0.33 Mn 0.33 Co 0.33 O 2 ; NMC-111) intact. This BM purification process is conducted at moderate temperatures in a KOH-based solution matrix. We rationally evaluate approaches to increase both the kinetic corrosion rate and the thermodynamic solubility of Al 0 and Cu 0 , and evaluate the impact of these treatment conditions on the structure, chemistry, and electrochemical performance of NMC. Specifically, we explore the impacts of chloride-based salts, a strong chelating agent, elevated temperature, and sonication on the rate and extent of contaminant corrosion, while concurrently evaluating the effects on NMC. The reported BM purification process is then demonstrated on samples of “simulated BM” containing a practically relevant 1 wt% concentration of Al or Cu. Increasing the kinetic energy of the purifying solution matrix through elevated temperature and sonication accelerates the corrosion of metallic Al and Cu, such that ∼100% corrosion of 75 μm Al and Cu particles is achieved within 2.5 hr. Further, we determine that effective mass transport of ionized species critically impacts the efficacy of Cu corrosion, and that saturated Cl – hinders rather than accelerates Cu corrosion by increasing solution viscosity and introducing competitive pathways for Cu surface passivation. The purification conditions do not induce bulk structural damage to NMC, and electrochemical capacity is maintained in half-cell format. Testing in full cells suggests that a limited quantity of residual surface species are present after treatment, which initially disrupt electrochemical behavior at the graphite anode but are subsequently consumed. Process demonstration on simulated BM suggests that contaminated samples—which prior to treatment show catastrophic electrochemical performance—can be recovered to pristine electrochemical capacity. The reported BM purification method offers a compelling and commercially viable solution to address contamination, particularly in the “fine” fraction of BM where contaminant sizes are on the same order of magnitude as NMC and where traditional separation approaches are unfeasible. Thus, this optimized BM purification technique offers a pathway towards viable direct recycling of BM feedstocks that would otherwise be unusable.

25 ENERGY STORAGE↗
DOE OSTI2021

Catalytic Reduction of Residual Oxygen for the Purification of Carbon Dioxide Streams from Pressurized Oxy-Combustors

Pressurized oxy-combustion (OC) is regarded as an energy-efficient alternative to atmospheric OC. To utilize the captured carbon dioxide (CO2) from pressurized OC for enhanced oil recovery or carbon storage in geological formations, the CO2 product stream must meet the required purity specifications. One major impurity in OC flue gases is residual O2 (e.g., 3 vol%). In this study, a catalytic approach has been investigated to remove the residual O2 through a reduction reaction with injected methane (CH4) in a reverse-flow fixed-bed (RFFB) reactor. The performance was tested for a supported copper (Cu)-based catalyst synthesized by incipient wetness impregnation and a cobalt-manganese (CoMn) oxide catalyst synthesized by a coprecipitation method. A commercial Cu-based catalyst was also studied as the reference. Experimental results revealed that under the reverse-flow operation, the temperature profiles in the reactor were symmetrical on both sides of the catalyst zone and were more homogenous than those under the conventional one-direction-flow operation. Among the tested catalysts, the CoMn catalyst was the most reactive for promoting the reduction of O2 with CH4, able to attain >95% O2 removal at 475 °C and a gas hourly space velocity (GHSV) of 18,000 h-1 with a feed gas containing 3 vol% O2. Under all experiments, the concentrations of carbon monoxide (CO) were lower than 30 ppmv in the effluent gas streams. The reaction between O2 and CH4 could be depicted by using the Mars–van Krevelen redox mechanism based on a two-step reduction–oxidation reaction pathway.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Upcycling of Mixed Aluminum Alloy Shredder Scrap using Shear Processing

Conservation of critical materials is an increasing area of focus in the Unites States. In 2023, aluminum was added to the US Department of Energy Final Critical Materials List which has spurred public and private research into sustainable management of these resources. Additionally, efficiency in manufacturing and conservation of natural resources are growing concerns with targets to lower global carbon emissions, as primary aluminum alloy production is energy intensive, requiring 14 MWh of electricity plus 0.4 tonnes of CO2 per tonne of Al. Due to these factors, is essential that more sustainable manufacturing methods for aluminum alloys are developed going forward. To this end, much research is ongoing on the topic of more efficient utilization and recovery. However, most of this research still requires primary aluminum in the production process. Here, it will be attempted to bypass the use of primary aluminum and produce useful material recycled from 100% post-consumer scrap. Even considering recent developments in recycling of Al scrap, there is still a large amount of post-consumer scrap that is underutilized due to high impurity content, and that amount will increase significantly as more and more aluminum alloys are utilized in vehicles. This “scrap wave” is expected to cover 80% of the demand for automotive aluminum alloys by 2050 . A challenge to be addressed before the coming scrap wave can be fully utilized is that the tolerance of manufacturing techniques to impurities or off-spec alloy compositions must be increased. Particularly, in 5000-and 6000-series alloys (the most common wrought alloys in durable products), excess iron, copper, and silicon create brittle intermetallics during casting that remain in the extruded microstructure which limit the formability, ductility, and corrosion resistance of the alloy. Concerningly, many of the highest-volume post-consumer aluminum scrap streams such as automotive shredder scrap contain a mix of alloys including both wrought and cast alloys. Their compositions can vary widely depending on geography and the time of year. Because they are mixed, they often contain high content of multiple alloying elements such as Si and Cu in higher concentrations than are found in typical wrought alloys. They may also be contaminated with non-Al alloys from fasteners that get mixed in and often have high content of unwanted elements such as Fe. As a method for utilizing these underused scrap streams that are high in tramp elements, an emerging extrusion technology is being developed at the Pacific Northwest National Laboratory (PNNL) that aims to upcycle 100% post-consumer aluminum scrap directly into extruded components without the addition of primary aluminum . This new technology, called Shear Assisted Processing and Extrusion (ShAPE), is enabling a shift away from today’s recycling paradigm by reaching deeper into lower-value scrap streams, using shredder scrap as the extrusion billet material. Sometimes referred to as Twitch or Tweak, these scrap streams result from shredding and sorting of automobiles, building materials, appliances, and consumer goods. ShAPE combines the linear axis of conventional extrusion with a rotating extrusion die. This rotating die applies large strain to the material during extrusion, which breaks up large impurity-containing intermetallic particles, reducing their deleterious effects. This has been demonstrated for 6063 machining scrap spiked with excess Fe, and Twitch scrap high in Fe, Si and Cu where strength and ductility were retained for both feedstock compositions. Additionally, the extreme plastic deformation during ShAPE enables extrusion of billets with high Si that are too brittle for processing by conventional extrusion. By using 100% post-consumer shedder scrap as feedstock, ShAPE has the potential to slash embodied energy and carbon in extruded components by >80% compared to conventional extrusion of primary aluminum alloys.

Milligan, Brian K.↗