Search NASA⌕ Search

SEARCH · Search NASA

Results for “Curved Surfaces”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Turbulent boundary layer on a convex, curved surface

The effects of strong convex curvature on boundary layer turbulence were investigated. The data gathered on the behavior of Reynolds stress suggested the formulation of a simple turbulence model. Three sets of data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning, and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero - thus avoiding any effects of streamwise acceleration on the wall layers. Results show that after a sudden introduction of curvature, the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. In contrast, when the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions.

Gillis, J. C.↗
NASA NTRS1981

Experimental data and model for the turbulent boundary layer on a convex, curved surface

Experiments were performed to determine how boundary layer turbulence is affected by strong convex curvature. The data gathered on the behavior of the Reynolds stress suggested the formulation of a simple turbulence model. Data were taken on two separate facilities. Both rigs had flow from a flat surface, over a convex surface with 90 deg of turning and then onto a flat recovery surface. The geometry was adjusted so that, for both rigs, the pressure gradient along the test surface was zero. Two experiments were performed at delta/R approximately 0.10, and one at weaker curvature with delta/R approximately 0.05. Results show that after a sudden introduction of curvature the shear stress in the outer part of the boundary layer is sharply diminished and is even slightly negative near the edge. The wall shear also drops off quickly downstream. When the surface suddenly becomes flat again, the wall shear and shear stress profiles recover very slowly towards flat wall conditions. A simple turbulence model, which was based on the theory that the Prandtl mixing length in the outer layer should scale on the velocity gradient layer, was shown to account for the slow recovery.

Gillis, J. C.↗
NASA NTRS1982

Goertler instability in compressible boundary layers along curved surfaces with suction and cooling

The Goertler instability of the laminar compressible boundary layer flows along concave surfaces is investigated. The linearized disturbance equations for the three-dimensional, counter-rotating streamwise vortices in two-dimensional boundary layers are presented in an orthogonal curvilinear coordinate. The basic approximation of the disturbance equations, that includes the effect of the growth of the boundary layer, is considered and solved numerically. The effect of compressibility on critical stability limits, growth rates, and amplitude ratios of the vortices is evaluated for a range of Mach numbers for 0 to 5. The effect of wall cooling and suction of the boundary layer on the development of Goertler vortices is investigated for different Mach numbers.

El-Hady, N.↗
NASA NTRS1983

Growth of Goertler vortices in compressible boundary layers along curved surfaces

An investigation of the growth of the three-dimensional, counter-rotating, longitudinal type vortices is considered in two-dimensional laminar compressible boundary-layer flow. The basic approximation of the disturbance equations that includes the terms due to boundary layer growth is considered and solved numerically. These terms are shown to have large local effects near the neutral stability region. The study shows that the instability of the boundary layer with respect to the three-dimensional vortices sets in at higher Goertler number as Mach number increases. Also the maximum amplitude ratio of the vortices is reduced by about 20 percent as Mach number increases from 0 to 5.

El-Hady, N. M.↗
NASA NTRS1984

Heat transfer and turbulence measurements of a film-cooled flow over a convexly curved surface

Heat transfer and hydrodynamic boundary layer measurements were made in a turbulent boundary layer on a convex surface with 13 rows of injection. Both full- and partial-coverage cases were tested for three blowing ratios: 0.2, 0.4, and 0.6. Heat transfer results are discussed in terms of Stanton number with injection air temperature equal to wall temperature. In the blown region, for both m (blowing ratio) = 0.2 and 0.4, the local response of the boundary layer is dominated by curvature, and m = 0.4 shows higher cooling effects than m = 0.2 or 0.6, as expected, based on flat-plate results. Hydrodynamic measurements with a triple-hot-wire suggest the existence of two streamwise lanes. Lanes containing injection holes are highly affected by injection and show a definite streamwise evolution. Lanes which do not contain holes are not affected much by injection and show little change in the streamwise direction.

Furuhama, K.↗
NASA NTRS1986

Computation of nonstationary strong shock diffraction by curved surfaces

A two-dimensional, high resolution shock-capturing algorithm was used on a supercomputer to solve Eulerian gasdynamic equations in order to simulate nonstationary strong shock diffraction by a circular arc model in a shock tube. The hypersonic Mach shock wave was assumed to arrive at a high angle of incidence, and attention was given to the effect of varying values of the ratio of specific heats on the shock diffraction process. Details of the conservation equations of the numerical algorithm, written in curvilinear coordinates, are provided, and model output is illustrated with the results generated for a Mach shock encountering a 15 deg circular arc. The sample graphics include isopycnics, a shock surface density profile, and pressure and Mach number contours.

Yang, J. Y.↗
NASA NTRS1987

A preliminary investigation of large-scale organized motions in a supersonic turbulent boundary layer on a curved surface

An experimental investigation concentrating on the change in the large-scale organized motions of a supersonic turbulent boundary layer subjected to a short region of concave surface curvature is presented. Two flows were studied, a relatively weak and a relatively strong perturbation. In both flows the freestream Mach number was 2.89 and the Reynolds number based on momentum thickness was 81,900. Hot-wire anemometry and schlieren photography provided the principle tools for this investigation. Hot-wire data were analyzed using spectral and correlation methods and conditional sampling techniques. Changes in structure angle and results of conditionally sampled velocity signals are discussed. The strong perturbation is found to increase the structure angle, and in both flows the length scales of the organized motions are altered.

Donovan, J. F.↗
NASA NTRS1987

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Tests were performed in a transient heat transfer tunnel in which the model under test was preheated prior to allowing room temperature air to be suddenly drawn over the model. The resulting movement of isothermal contours on the model is revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record is obtained of a temperature and time data pair for all points on the model during a single test. Experiments on a duct model are reported in which the model was preheated using a hot air stream. A manner in which initial model temperature nonuniformities could be taken into account was investigated. The duct model was also tested with a steady-state measurement technique and results were compared with the transient measurements, but recognizing that differences existed between the upstream thermal boundary conditions. The steady-state and transient measurements were shown to be consistent with predicted values. The main advantage of this transient heat transfer technique using liquid crystals is that since the test model need not be actively heated, high-resolution measurements on surfaces with complex shapes may be obtained.

Jones, T. V.↗
NASA NTRS1988

High-resolution heat-transfer-coefficient maps applicable to compound-curve surfaces using liquid crystals in a transient wind tunnel

Tests were performed in a transient heat transfer tunnel in which the model under test was preheated prior to allowing room temperature air to be suddenly drawn over the model. The resulting movement of isothermal contours on the model is revealed using a surface coating of thermochromic liquid crystals that display distinctive colors at particular temperatures. A video record is obtained of a temperature and time data pair for all points on the model during a single test. Experiments on a duct model are reported in which the model was preheated using a hot air stream. A manner in which initial model temperature nonuniformities could be taken into account was investigated. The duct model was also tested with a steady-state measurement technique and results were compared with the transient measurements, but recognizing that differences existed between the upstream thermal boundary conditions. The steady-state and transient measurements were shown to be consistent with predicted values. The main advantage of this transient heat transfer technique using liquid crystals is that since the test model need not be actively heated, high-resolution measurements on surfaces with complex shapes may be obtained.

Jones, Terry V.↗
NASA NTRS1988

Instability and sound emission from a flow over a curved surface

The growth and decay of a wavepacket convecting in a boundary layer over a concave-convex surface is studied numerically using direct computations of the Navier-Stokes equations. The resulting sound radiation is computed using the linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. It is shown that on the concave portion the amplitude of the wavepacket increases and its bandwidth broadens while on the convex portion some of the components in the packet are stabilized. The pressure field decays exponentially away from the surface and then algebraically exhibits a decay characteristic of acoustic waves in two dimensions. The far-field acoustic pressure exhibits a peak at a frequency corresponding to the inflow instability frequency.

Maestrello, L.↗
NASA NTRS1989

Control of sound radiation from a wavepacket over a curved surface

Active control of acoustic pressure in the far field resulting from the growth and decay of a wavepacket convecting in a boundary layer over a concave-convex surface is investigated numerically using direct computations of the Navier-Stokes equations. The resulting sound radiation is computed using linearized Euler equations with the pressure from the Navier-Stokes solution as a time-dependent boundary condition. The acoustic far field exhibits directivity type of behavior that points upstream to the flow direction. A fixed control algorithm is used where the attenuation signal is synthesized by a filter which actively adapt it to the amplitude-time response of the outgoing acoustic wave.

Maestrello, Lucio↗
NASA NTRS1990

Large-scale motions in a supersonic turbulent boundary layer on a curved surface

This paper presents measurements in a Mach 3 turbulent boundary layer which was subjected to a short region of concave surface curvature. Mean velocity and time-averaged turbulence measurements are presented to indicate the severity of the distortion, although the focus of this study is on how the large-scale organized motions are affected by the distortion. A 12 deg increase in the inclination angle of organized motions is observed, and correlation measurements indicate an increase in the streamwise length scale. VITA conditional sampling is used to identify strong positive streamwise mass-flux gradients as the large-scale structure responsible for the measured structure angle and to determine the ensemble-averaged flowfield associated with the mass-flux gradient structures.

Donovan, J. F.↗
NASA NTRS1966

The Properties of Flowing Sheets Formed by Impingement of Liquid Jets on Curved Surfaces

An applied research program was conducted to determine the properties of flat sheets of propellants formed by directing jets of liquid tangentially against concave, cylindrical deflector surfaces. The dimensions and spatial orientation of the resultant sheets were found to depend only on the orifice diameter and deflector geometry for three propellant simulants of widely-varying physical properties, over the range of injection velocities encountered in liquid rocket engines. Correlating equations, suitable for use in injector design, are presented for free-sheet width and spreading angle. Distribution of mass and velocity across the free-flowing sheets is also reported. Conditions were discovered under which true sheets do not form, or at best malformed or pulsating sheets result. An envelope of geometrical constraints for deflector design is tentatively defined in order to avoid these undesirable operating regions. The results of the present cold-flow tests are compared with firing test data for impinging-sheet injectors and combustion performance is related to single sheet behavior.

Riebling, Robert W.↗
NASA NTRS1989

Surface roughness of flat and curved optical surfaces

Surface roughness measurement has several applications. Even a few A roughness will cause scattered light in optical systems. Smooth surfaces are required in a wide variety of instruments. For example, the outputs of the high power lasers are limited by the surface roughness of mirrors and windows. Similarly, the information storage capacity of magnetic media is limited by the roughness of the surface. Roughness reduces the resolving power of optics and distorts images. The performance of certain thin film components in electronic industries is affected by the roughness on the film surface. X-ray astronomical telescopes require smooth curved surfaces. To improve the surface quality, super sensitive detection methods are required. Wide ranging measurement techniques are developed based on interferometry, electron microscopy, C-rays, ellipsometry, light scattering, and using mechanical stylus, etc. Though there are several techniques available for measurement and evaluation of the surfaces, no single technique is fully adequate. Also, the technique used should be nondestructive and highly sensitive. So, an optical heterodyne profilometer was fabricated. Its current sensitivity is much better than 10A rms. It is a noncontact and nondestructive technique. The instrument can be operated even by unskilled personnel for routine measurements.

George, M. C.↗
NASA NTRS1983

Radiation exchange in large space structures and frames

The analysis of radiation heat transfer is determined by the need to determine the geometrical quantity, F(ij), which is commonly called the view factor, and which represents the fraction of energy leaving surface i which strikes surface j. The present investigation shows that the use of a rotating plane to model a one-dimensional radiation element is both computationally efficient and accurate. Because of the reduced computational cost of this element, radiation view factors for complex structures can be calculated directly. Under some conditions, the characteristics of the one-dimensional element may lead to a loss in accuracy when it is used to model obstructing cylinders. In cases in which the element is too close to the radiating surfaces, curved surfaces must be represented by a collection of flat planes. However, it appears that as long as the one-dimensional element is more than 5 diameters from the other surfaces, its use is valid.

Emery, A. F.↗
NASA NTRS1985

The Construction of Curves and Surfaces Using Numerical Optimization Techniques

Numerical optimization techniques are playing an increasing role in curve and surface construction. Often difficult problems in curve and surface construction, especially when some aspect of shape control is involved, can be phrased as a constrained optimization problem. Four such classes of problems are explored: parametric curve fitting with non-linear shape constraints; explicit surface fitting with linear shape constraints; surface fitting to scattered data giving rise to ill-posed problems; finally, variable knot problems. In each of these problems there is a nonlinear aspect: either the shape of the curve or surface is important for manufacturing or engineering reasons or the shape affects the convergence of numerical algorithms which use the curve or surface or the placement of knots affects the accuracy of the fits. In all cases the class of functions used is that of parametric spline curves and tensor or direct product spline surfaces. The reason for choosing this class is that splines provide flexible models that are easily evaluated and stored. Furthermore, the B-spline representation of splines leads to convenient expressions for shape control over regions.

Ferguson, D. R.↗
NASA NTRS2005

Shape Sensing a Morphed Wing with an Optical Fiber Bragg Grating

We suggest using distributed fiber Bragg sensors systems which were developed locally at Langley Research Center carefully placed on the wing surface to collect strain component information at each location. Then we used the fact that the rate change of slope in the definition of linear strain is very small and can be treated as a constant. Thereby the strain distribution information of a morphed surface can be reduced into a distribution of local slope information of a flat surface. In other words a morphed curve surface is replaced by the collection of individual flat surface of different slope. By assembling the height of individual flat surface, the morphed curved surface can be approximated. A more sophisticated graphic routine can be utilized to restore the curved morphed surface. With this information, the morphed wing can be further adjusted and controlled. A numerical demonstration is presented.

Tai, Hsiang↗