Search NASA⌕ Search

SEARCH · Search NASA

Results for “DIAMOND WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Extension of leading-edge-suction analogy to wings with separated flow around the side edges at subsonic speeds

A method for determining the lift, drag, and pitching moment for wings which have separated flow at the leading and side edges with subsequently reattached flow downstream and inboard is presented. Limiting values of the contribution to lift of the side-edge reattached flow are determined for rectangular wings. The general behavior of this contribution is computed for rectangular, cropped-delta, cropped-diamond, and cropped-arrow wings. Comparisons of the results of the method and experiment indicate reasonably good correlation of the lift, drag, and pitching moment for a wide planform range. The agreement of the method with experiment was as good as, or better than, that obtained by other methods. The procedure is computerized and is available from COSMIC as NASA Langley computer program A0313.

Lamar, J. E.↗
NASA NTRS1958

Investigation of Minimum Drag and Maximum Lift-drag Ratios of Several Wing-body Combinations Including a Cambered Triangular Wing at Low Reynolds Numbers and at Supersonic Speeds

Theoretical and experimental data for wing-body combinations with wings of triangular, arrow, and diamond plan form are presented for Mach numbers of 1.62, 1.93, and 2.41 and a Reynolds number range of 1.4 x 10 to the 6th power to 0.7 x 10 to the 6th power. Included are two each of triangular and arrow plan-form wings cambered for approximately uniform load at m = 1.62 and lift coefficients of 0.08 and 0.20. Liquid-film studies of the flow over the various configurations are also presented.

Brown, Clinton E↗
NASA NTRS1988

The Flying Diamond: A joined aircraft configuration design project, volume 1

The results of the analysis conducted on the Joined Wing Configuration study are presented. The joined wing configuration employs a conventional fuselage and incorporates two wings joined together near their tips to form a diamond shape in both plan view and front view. The arrangement of the lifting surfaces uses the rear wing as a horizontal tail and as a forward wing strut. The rear wing has its root at the tip of the vertical stabilizer and is structurally attached to the trailing edge of the forward wing. This arrangement of the two wings forms a truss structure which is inherently resistant to the aerodynamic bending loads generated during flight. This allows for a considerable reduction in the weight of the lifting surfaces. With smaller internal wing structures needed, the Joined Wing may employ thinner wings which are more suitable for supersonic and hypersonic flight, having less induced drag than conventional cantilever winged aircraft. Inherent in the Joined Wing is the capability of the generation of direct lift and side force which enhance the performance parameters.

Ball, Chris↗
NASA NTRS1974

Comparisons of two-dimensional shock-expansion theory with experimental aerodynamic data for delta-planform wings at high supersonic speeds

An investigation has been conducted to explore the potential for optimizing airfoil shape at high supersonic speeds by utilizing the two-dimensional shock-expansion method. Theoretical and experimental force and moment coefficients are compared for four delta-planform semispan wings having a leading-edge sweep angle of 65 deg and incorporating modified diamond airfoils with a thickness-chord ratio of 0.06. The wings differ only in airfoil maximum-thickness position and camber. The experimental data are obtained at Mach numbers of 3.95 and 4.63 and at a Reynolds number of 9.84 million per meter. A relatively simple method is developed for predicting, in terms of lift-drag ratio, the optimum modified diamond airfoil at high supersonic and hypersonic speeds.

Jernell, L. S.↗
NASA NTRS2005

Pressure-Sensitive Paint Investigation of Double-Delta Wing Vortex Flow Manipulation

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the effect of wing fillets on the global vortex-induced surface static pressure field about a sharp leading-edge 76 deg/40 deg double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 30 degrees using an in-situ method featuring the simultaneous acquisition of electronically-scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M = 0.50 to 0.85 but increased to several percent at M = 0.95 and 1.20. The PSP pressure distributions and pseudo-colored planform view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having a parabolic or diamond planform situated at the strake-wing intersection were designed to manipulate the vortical flows by, respectively, removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗
NASA NTRS2004

Pressure-Sensitive Paint Investigation of Double-Delta Wing Vortex Flow Manipulation

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to quantify the effect of wing fillets on the global vortex-induced surface static pressure field about a sharp leading-edge 76o/40o double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 20 degrees using an in-situ method featuring the simultaneous acquisition of electronically-scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M = 0.50 to 0.85 but increased to several percent at M =0.95 and 1.20. The PSP pressure distributions and pseudo-colored planform view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having a parabolic or diamond planform situated at the strake-wing intersection were designed to manipulate the vortical flows by, respectively, removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗
NASA NTRS2006

Wind Tunnel Application of a Pressure-Sensitive Paint Technique to a Double Delta Wing Model at Subsonic and Transonic Speeds

A pressure-sensitive paint (PSP) technique was applied in a wind tunnel experiment in the NASA Langley Research Center 8-Foot Transonic Pressure Tunnel to study the effect of wing fillets on the global vortex induced surface static pressure field about a sharp leading-edge 76 deg./40 deg. double delta wing, or strake-wing, model at subsonic and transonic speeds. Global calibrations of the PSP were obtained at M(sub infinity) = 0.50, 0.70, 0.85, 0.95, and 1.20, a Reynolds number per unit length of 2.0 million, and angles of attack from 10 degrees to 20 degrees using an insitu method featuring the simultaneous acquisition of electronically scanned pressures (ESP) at discrete locations on the model. The mean error in the PSP measurements relative to the ESP data was approximately 2 percent or less at M(sub infinity) = 0.50 to 0.85 but increased to several percent at M(sub infinity) =0.95 and 1.20. The PSP pressure distributions and pseudo-colored, planform-view pressure maps clearly revealed the vortex-induced pressure signatures at all Mach numbers and angles of attack. Small fillets having parabolic or diamond planforms situated at the strake-wing intersection were respectively designed to manipulate the vortical flows by removing the leading-edge discontinuity or introducing additional discontinuities. The fillets caused global changes in the vortex-dominated surface pressure field that were effectively captured in the PSP measurements. The vortex surface pressure signatures were compared to available off-surface vortex cross-flow structures obtained using a laser vapor screen (LVS) flow visualization technique. The fillet effects on the PSP pressure distributions and the observed leading-edge vortex flow characteristics were consistent with the trends in the measured lift, drag, and pitching moment coefficients.

Erickson, Gary E.↗
NASA NTRS1950

Downwash in Vortex Region Behind Rectangular Half-wing at Mach Number 1.91

Results of an experimental investigation to determine downwash and wake characteristics in region of trailing vortex system behind a rectangular half-wing at Mach number 1.91 are presented. The wing had a 5-percent thick symmetric diamond cross section beveled to a knife edge at the tip. At small angles of attack, downwash angles were in close agreement with predictions of linearized theory based on the assumption of an undistorted vortex sheet. At higher angles of attack, the flow was greatly influenced by the rolling up of the vortex sheet.

Cummings, John L↗
NASA NTRS1988

Parametric weight evaluation of joined wings by structural optimization

Joined-wing aircraft employ tandem wings having positive and negative sweep and dihedral, arranged to form diamond shapes in both plan and front views. An optimization method was applied to study the effects of joined-wing geometry parameters on structural weight. The lightest wings were obtained by increasing dihedral and taper ratio, decreasing sweep and span, increasing fraction of airfoil chord occupied by structural box, and locating the joint inboard of the front wing tip.

Miura, Hirokazu↗
NASA NTRS1992

Longitudinal and lateral-directional aerodynamic characteristics of a wing-cone configuration at Mach numbers from 2.5 to 4.5

A study was conducted to determine the longitudinal and lateral-directional aerodynamic characteristics of a generic wing-cone configuration at supersonic speeds. The fuselage has a 5 deg half-angle cone forebody, cylindrical midbody, and a 9 deg truncated cone afterbody. The delta wing (aspect ratio 1.0) had a 4 pct. thick diamond airfoil section. The tests were made in the Langley Unitary Plan Wind Tunnel at Mach numbers from 2.50 and 4.50. Angle of attack was varied from -4 to 28 degs, and angle of sideslip varied from -8 to 8 degs. Several configurations were studied to determine the effects of variations in wing longitudinal position, wing incidence, vertical tail configuration, canard shape, and nose bluntness. Typical effects of Reynolds number and Mach number on the longitudinal characteristics were observed. The incremental effects of the configuration variables were generally unaffected by Mach number. The directional stability characteristics of the large and small centerline mounted vertical tail configurations were significantly degraded with increasing angle of attack and Mach number.

Covell, Peter F.↗
NASA NTRS2019

Adjoint-Based Anisotropic Mesh Adaptation for a Stabilized Finite-Element Flow Solver

An adjoint solver is implemented in the FUN3D stabilized finite-element flow solver. The adjoint solution is used to generate anisotropic, adapted meshes to control error in scalar out- put functionals, such as lift or drag coefficient. The inviscid and turbulent adjoints are verified with a finite-difference derivative approximation and can be used in design optimization in addition to mesh adaptation. The adjoint capability represents an extension of previous research using the FUN3D stabilized finite-element capability with metric-based mesh adaptation and interpolation-based error estimates to generate highly anisotropic adapted meshes for turbulent flows. In the present work, a metric-based approach is again utilized, where the adjoint and the primal solutions both contribute to the generation of a metric tensor field that is subsequently used to produce the required anisotropic mesh for each adaptation cycle. Adaptive results are then shown for an inviscid supersonic flow over a diamond airfoil, inviscid transonic flow over the ONERA M6 wing, and viscous laminar flow over the NACA 0012 airfoil, all using drag force as the output functional. Adjoint-based adaptation is compared with a multiscale solution-based approach that controls the L norm of Mach number interpolation error to demonstrate the effectiveness and effciency of the adjoint-based adaptive mesh technology.

Balan, Aravind↗
NASA NTRS1985

Impact of airfoil profile on the supersonic aerodynamics of delta wings

A nonlinear flow model was employed to predict the flowfield, pressure and force data for delta wings at supersonic speeds. The goal of the study was to investigate the influence the airfoil profiles has on the wing aerodynamics. The analysis covers wing aspect ratios from 0.5-3.0 with leading edge sweep of 0.5-4.0 on diamond, circular arc and NACA modified 4-digit airfoils. Nonlinear aerodynamics are approximated with nonlinear zero-lift wave drag curves, yielding results significantly different from those obtained from linear calculations. The analytical technique, useful in preliminary design studies, indicates in all cases that 90 percent of wave drag is generated at the wing apex and trailing edge.

Wood, R. M.↗
NASA NTRS1990

Numerical simulation of steady and unsteady asymmetric vortical flow

The unsteady, compressible, thin-layer, Navier-Stokes equations are solved to simulate steady and unsteady, asymmetric, vortical laminar flow around cones at high incidences and supersonic Mach numbers. The equations are solved by using an implicit, upwind, flux-difference splitting, finite-volume scheme. Locally conical flows are assumed and the solutions are obtained by forcing the conserved components of the flowfield vector to be equal at two axial stations located at 0.95 and 1.0. Computational examples cover steady and unsteady asymmetric flows around a circular cone and its control using side strakes. Unsteady asymmetric flows are also presented for elliptic- and diamond-section cones, which model asymmetric vortex shedding around round and sharp-edged delta wing flows.

Kandil, O. A.↗
NASA NTRS1992

Infrared spectroscopy of dense clouds in the C-H stretch region - Methanol and 'diamonds'

The paper presents high spectral resolution studies in the 3100-2600/cm range of the protostars NGC 7538 IRS9, W33A, W3 IRS 5, and S140 IRS 1. Well-resolved absorption bands at about 2825/cm and 2880/cm were found superposed on the LF wing of the strong O-H stretch feature. The 2880/cm band, previously detected toward W33A, is also in the spectrum of NGC 7538 IRS 9. The relative strength of these two bands varies, showing that they are associated with two different carriers. The new band at about 2880/cm falls near the position of C-H stretching vibrations in tertiary carbon atoms. The strength of this feature, in combination with the lack of strong features associated with primary and secondary carbon atoms, suggests that the carrier of the new feature has a diamondlike structure. This new feature is tentatively attributed to interstellar 'diamonds'. The detection of this band in the spectra of all four dense molecular clouds suggests that the carrier is ubiquitous in dense clouds.

Allamandola, L. J.↗
NASA NTRS1993

A flutter investigation of all-moveable NASP-like wings at hypersonic speeds

Six alternative all-moving wing configurations applicable to the NASP hypersonic/transatmospheric vehicle have undergone aeroelasticity testing in NASA-Langley's Mach-20-capable Helium Tunnel that yielded data for such parametric variations as airfoil profile and wing planform, wing-pivot flexure stiffness, and mass imbalance. While all wings fluttered at dynamic pressures lower than predicted by second-order piston-theory aerodynamics, this was of limited amplitude, suggesting nonlinear external-flow behavior. Slab airfoils were more stable than diamond-shaped ones; blunt leading edges enhance stability relative to sharp ones, and stiffer pivolts extert a stabilizing influence.

Spain, Charles V.↗
NASA NTRS1986

Continuous, Multielement, Hot-Film Transition Gage

Accurate measurement of location where laminar boundary layer undergoes transition to turbulent one serves many purposes in basic aero-dynamic research and developmental testing. Individual gages must be staggered to prevent formation of turbulence at gages downstream. This arrangement precludes accurate measurements of laminar/turbulent transition regions along streamline. Complete understanding of performance, stability, and control of laminar-flow airplane requires knowledge of transition locations on wing surface, empennage surfaces, fuselage, and nacelles. Visual, acoustic, and electronic methods capable of providing this transition information.

Holmes, B.↗
NASA NTRS1995

Low-speed wind-tunnel investigation of the stability and control characteristics of a series of flying wings with sweep angles of 50 deg

A wind-tunnel investigation was conducted in the Langley 12-Foot Low-Speed Tunnel to study the low-speed stability and control characteristics of a series of four flying wings over an extended range of angle of attack (-8 deg to 48 deg). Because of the current emphasis on reducing the radar cross section (RCS) of new military aircraft, the planform of each wing was composed of lines swept at a relatively high angle of 50 deg, and all the trailing-edge lines were aligned with one of the two leading edges. Three arrow planforms with different aspect ratios and one diamond planform were tested. The models incorporated leading-edge flaps for improved longitudinal characteristics and lateral stability and had trailing-edge flaps in three segments that were deflected differentially for roll control, symmetrically for pitch control, and in a split fashion for yaw control. Three top body widths and two sizes of twin vertical tails were also tested on each model. A large aerodynamic database was compiled that could be used to evaluate some of the trade-offs involved in the design of a configuration with a reduced RCS and good flight dynamic characteristics.

Fears, Scott P.↗