Search NASA⌕ Search

SEARCH · Search NASA

Results for “Design for Additive Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Efficient Thermal Management for Sampling Arm Actuators

An electric actuator incorporating novel features for thermal management is designed and analyzed. Reducing intra-actuator thermal resistance is not only beneficial for cold missions (helping to pre-heat the gearbox) but can also enable high power applications in benign environments. The proposed design increases the thermal conductance between the motor windings and the motor casing by at least two orders of magnitude over the state of practice actuator designs. The design leverages Additive Manufacturing (AM) to integrate a complex 3 dimensional Oscillating Heat Pipe (OHP) directly within the actuator structure. A baseline actuator without this thermal management feature was fabricated. Testing was conducted to evaluate the temperature difference between actuator components at a range of motor winding heat dissipations. An analysis of a proposed revised design incorporating OHPs into the input structure indicated an increase in the effective thermal conductivity of 8 and 22 times for the nominal and start-up modes respectively. In addition, the thermal conductance between the windings and the input structure is increased by a factor of 90, and the thermal conductance between the windings and the gear assembly is increased by a factor of 200 with the proposed design.

Odagiri, Kimihide↗
NASA NTRSDate not supplied

Windform® XT 2.0 Use as 3U CubeSat Primary Structure

CubeSats provide a platform for small-scale space research and technology demonstration at reduced complexity, cost, and development time. These advantages drove the NASA Langley Research Center (LaRC) to develop and launch the GPX2 3U CubeSat to explore the viability of using Commercial Off-The-Shelf (COTS) differential GPS (dGPS) in low earth orbit. To reduce manufacturing costs and increase design flexibility, the project chose additive manufactured Windform® XT 2.0 as the primary bus material rather than traditional subtractive manufactured (milled) metal. The bus is a two-part, Selective Laser Sintered, 3D-print structure consisting of a single-piece, five-walled chassis and single-walled cover. The bus was specially designed to allow the project to accommodate the payload electronics stack as well as antennas, receivers, and deployable mechanisms. By using an additive manufactured solution, LaRC was able to design in features unrealizable through traditional milling, with a lead-time of roughly two weeks. In comparison, traditional subtractive manufacturing limits geometry options due to toolpath reach and bus construction would have required multiple components for each wall. This would have resulted in a more costly, longer lead-time article with more joints, fasteners, and complexity with a commensurate increase in overall mass. A number of lessons-learned were captured during the design, analysis, and testing of the GPX2 CubeSat covering thermal and structural analysis, vibration modeling, and geometric tolerancing. Additionally, a variety of material testing and verification were performed before and during spacecraft design and integration to assure the suitability of Windform® XT 2.0 for the launch and mission environments. This article provides the highlights of designing and testing the GPX2 bus.

CubeSat↗
NASA NTRS2021

A Summary of Normal Incidence Tube Tests of NASA'S Bio-inspired Broadband Acoustic Absorber

Motivated by the need to reduce noise pollution from aircraft engines, NASA has continued to design, manufacture and test recently patented structures that mimic the geometry and the broadband and low frequency acoustic absorption of assemblies of natural reeds. This report documents a screening test, which is a precursor to more controlled modelling experiments. The purpose of this experiment was to identify variables and prototype design features that might play a dominant role in the acoustic performance of these structures. To date, twenty-four prototypes, each with an overall shape of a cube (nominally 50 mm x 50 mm x 50 mm), were designed and additively manufactured from thermoplastics using a Fused Filament Fabrication technique. The prototypes were tested in the NASA Glenn and Langley Normal Incidence Tubes to experimentally determine the acoustic absorption as a function of frequency from 400 Hz to 3000 Hz. Results indicate that a variety of structures exhibit substantial acoustic absorption in that frequency range, with an average absorption coefficient greater than 0.6, especially in the frequency range of 400 Hz to 1000 Hz. Six basic prototype designs were chosen to inform future modeling research. Results of these experiments can be used to evaluate existing physics-based models of the interaction of sound waves with these structures or to develop new models. Validated physics-based models of these structures can help engineers optimize the designs for different commercial noise control applications.

Acoustics↗
NASA NTRS2013

Cosmo Cassette: A Microfluidic Microgravity Microbial System For Synthetic Biology Unit Tests and Satellite Missions

Although methods in the design-build-test life cycle of the synthetic biology field have grown rapidly, the expansion has been non-uniform. The design and build stages in development have seen innovations in the form of biological CAD and more efficient means for building DNA, RNA, and other biological constructs. The testing phase of the cycle remains in need of innovation. Presented will be both a theoretical abstraction of biological measurement and a practical demonstration of a microfluidics-based platform for characterizing synthetic biological phenomena. Such a platform demonstrates a design of additive manufacturing (3D printing) for construction of a microbial fuel cell (MFC) to be used in experiments carried out in space. First, the biocompatibility of the polypropylene chassis will be demonstrated. The novel MFCs will be cheaper, and faster to make and iterate through designs. The novel design will contain a manifold switchingdistribution system and an integrated in-chip set of reagent reservoirs fabricated via 3D printing. The automated nature of the 3D printing yields itself to higher resolution switching valves and leads to smaller sized payloads, lower cost, reduced power and a standardized platform for synthetic biology unit tests on Earth and in space. It will be demonstrated that the application of unit testing in synthetic biology will lead to the automatic construction and validation of desired constructs. Unit testing methodologies offer benefits of preemptive problem identification, change of facility, simplicity of integration, ease of documentation, and separation of interface from implementation, and automated design.

Bioelectrochemical System↗
NASA NTRS2019

CAMIEM: Compact Additively Manufactured Innovative Electric Motor

New manufacturing methods are needed to obtain innovative electric motor designs that have much higher power densities and/or efficiencies compared to the current state-of-the-art. Additive manufacturing offers the potential to radically change motor designs so that they have compact designs, multi-material components, innovative cooling, and optimally designed and manufactured components. New component designs enabled by additive manufacturing technologies have been designed and were fabricated to include the housing, rotors, stator cooling ring, a direct printed stator, and a wire embedded stator. The new components were integrated into the motor and tested evaluate the performance gains in comparison to the baseline electric motor configuration. Partners on the sub-project include NASA GRC, NASA LaRC, NASA AFRC, LaunchPoint Technologies, and the University of Texas El Paso.

Halbig, Michael C.↗
NASA NTRSDate not supplied

Development of an Additive Manufactured Cryogenic TVS Augmented Injector

Cryogenic fluid transfer is critical in ground and space systems. Transfer typically requires venting a receiver vessel during the chill and fill process to maintain a pressure favorable to fluid flow. Venting in space is problematic due to low-gravity where fluid position is indeterminate; possibly allowing fluid to flow out the vent. To control receiver tank venting the vented chill/no-vent fill methodology is attractive. An additively manufactured Injector coupled with a Thermodynamic Venting System (TVS) augmentation can enable the vented chill/no-vent fill approach with simplified operations. The TVS augmented injector includes an internal heat exchanger, fluid injector spray head, and external surface condensation heat exchange; combined with integrated flow paths in one part. Operations using the injector allow the tank vent to be closed very early in the transfer and not reopened. The TVS circuit eliminates the potential for stalled fill by maintaining cooling flow on the injector and condenser elements, reducing tank pressure. The injector can also be employed for long-term cryo fluid storage as a means of controlling tank pressure if integrated with a recirculation pump. A cryo-cooler can be used in place of/or augmenting the TVS flow circuit for a zero loss pressure control system. The Injector was developed using the principles of design for additive manufacture and printed as one part, resulting in part count reduction, improved reproducibility, shorter lead times, and reduced cost. The TVS augmented injector is compact and highly adaptable simplifying its integration. A key benefit is that this methodology enables simplified operations in reaching 100% fill conditions.

Omar Mireles↗
NASA NTRS2017

Predictive Modeling of Fast-Curing Thermosets in Nozzle-Based Extrusion

This work presents an approach to modeling the dynamic spreading and curing behavior of thermosets in nozzle-based extrusions. Thermosets cover a wide range of materials, some of which permit low-temperature processing with subsequent high-temperature and high-strength working properties. Extruding thermosets may overcome the limited working temperatures and strengths of conventional thermoplastic materials used in additive manufacturing. This project aims to produce technology for the fabrication of thermoset-based structures leveraging advances made in nozzle-based extrusion, such as fused deposition modeling (FDM), material jetting, and direct writing. Understanding the synergistic interactions between spreading and fast curing of extruded thermosetting materials will provide essential insights for applications that require accurate dimensional controls, such as additive manufacturing [1], [2] and centrifugal coating/forming [3]. Two types of thermally curing thermosets -- one being a soft silicone (Ecoflex 0050) and the other being a toughened epoxy (G/Flex) -- served as the test materials in this work to obtain models for cure kinetics and viscosity. The developed models align with extensive measurements made with differential scanning calorimetry (DSC) and rheology. DSC monitors the change in the heat of reaction, which reflects the rate and degree of cure at different crosslinking stages. Rheology measures the change in complex viscosity, shear moduli, yield stress, and other properties dictated by chemical composition. By combining DSC and rheological measurements, it is possible to establish a set of models profiling the cure kinetics and chemorheology without prior knowledge of chemical composition, which is usually necessary for sophisticated mechanistic modeling. In this work, we conducted both isothermal and dynamic measurements with both DSC and rheology. With the developed models, numerical simulations yielded predictions of diameter and height of droplets, along with width and height of extruded lines cured at varied temperatures. Experimental results carried out on a goniometric platform and a nozzle-based 3D printer showed agreement with the numerical simulations. Finally, this presentation will show how the models are adaptable to the planning of tool paths and designs in additive manufacturing.

Xie, Jingjin↗
NASA NTRS2015

In-Space Manufacturing: Pioneering a Sustainable Path to Mars

In order to provide meaningful impacts to exploration technology needs, the In-Space Manufacturing (ISM) Initiative must influence exploration systems design now. In-space manufacturing offers: dramatic paradigm shift in the development and creation of space architectures; efficiency gain and risk reduction for low Earth orbit and deep space exploration; and "pioneering" approach to maintenance, repair, and logistics leading to sustainable, affordable supply chain model. In order to develop application-based capabilities in time to support NASA budget and schedule, ISM must be able to leverage the significant commercial developments, which requires innovative, agile collaborative mechanisms (contracts, challenges, SBIR's, etc.); and NASA-unique investments to focus primarily on adapting the technologies and processes to the microgravity environment. We must do the foundational work - it is the critical path for taking these technologies from lab curiosities to institutionalized capabilities: characterize, certify, institutionalize, design for Additive Manufacturing (AM). Ideally, International Space Station (ISS) U.S. lab rack or partial rack space should be identified for in-space manufacturing utilization in order to continue technology development of a suite of capabilities required for exploration missions, as well as commercialization on ISS.

Werkheiser, Niki↗
NASA NTRS2017

Investigation of a Bio-Inspired Liner Concept

Four samples of natural reeds, Phragmites australis, were tested in the NASA Langley and Glenn Normal Incidence Impedance Tubes in order to experimentally determine the acoustic absorption coefficients as a function of frequency from 400 to 3000 Hz. Six samples that mimicked the geometry of the assemblies of natural reeds were also designed and additively manufactured from ASA thermoplastic and tested. Results indicate that structures can be manufactured of synthetic materials that mimic the geometry and the low frequency acoustic absorption of natural reeds. This accomplishment demonstrates that a new class of structures can now be considered for a wide range of industrial products that need thin, lightweight, broadband acoustic absorption effective at frequencies below 1000 Hz. Aircraft engine acoustic liners and aircraft cabin acoustic liners, in particular, are two aviation applications that might benefit from further development of this concept.

aerodynamics↗
NASA NTRSDate not supplied

A Review Towards the Design Optimization of High-Performance Additively Manufactured Rotating Detonation Rocket Engine Injectors

Rotating Detonation Rocket Engines (RDRE) have been marketed primarily for their higher specific impulse potential over constant pressure (CP) liquid rocket engines. However, several other performance advantages exist such as heat transfer advantages for gas expander cycle, increased completeness of combustion at low chamber L*, compact engine design, reduced coolant channel pressure drop potential, and improved injector C* performance. NASA has paved the way for liquid engine system performance enhancement since the Apollo program and continues to do so with metal additive manufacturing (AM), new advanced materials, and advanced propulsion concepts. A team of propulsion development engineers at NASA are in the process of developing high-performance 7K lbf class RDRE hardware for their potential use in lander, upper stage, and even launch vehicle applications. Clear advantages have been demonstrated with AM including program cost and schedule reductions of up to 50%. It is well known that injector performance is integrally linked to the global performance of a combustion device. This is especially the case for RDREs since detonation stability is heavily dependent on the mixedness of propellants. A major goal of this work is to identify what has been done in the open experimental literature and what injectors design features are conducive to high performance in the detonation cycle. This paper reviews the available literature and reports the primary gaps in the knowledge base needed by the pressure gain combustion (PGC) community. Major conclusions are documented, and suggestions given towards the design of high-performance liquid RDRE injectors. In addition, the integration of metal AM into the design of liquid RDRE injector schemes is included.

rotating detonation rocket engine↗
NASA NTRSDate not supplied

Evaluations of Additively Manufactured Superalloy Lattice Blocks

Cast lattice block structures made up of high-temperature superalloys were previously shown to offer advantages in density, efficiency, and tailored properties. However, inconsistencies in casting die-fill, composition, and microstructure were identified as persistent issues with the casting process path. Three candidate lattice designs were screened through additive manufacturing of a superalloy. Laser powder bed fusion was applied with superalloy powder to produce lattice blocks for three-dimensional octahedral unit-cell designs of three heights. Properties of the structural designs versus additively manufactured lattices were compared, including structural dimensions, densities, defects, grain structures, crystallographic texture, and surface residual stresses. Findings indicate this concept could produce useful superalloy structures for high-temperature-capable static components requiring tailored density, and thermophysical and mechanical properties.

superalloy↗
NASA NTRSDate not supplied

Additively Manufactured Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry decent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRSDate not supplied

Additively Manufactured Wind Tunnel Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry descent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRS2017

Systems and Methods for Designing and Fabricating Contact-Free Support Structures for Overhang Geometries of Parts in Powder-Bed Metal Additive Manufacturing

Systems and methods are provided for designing and fabricating contact-free support structures for overhang geometries of parts fabricated using electron beam additive manufacturing. One or more layers of un-melted metallic powder are disposed in an elongate gap between an upper horizontal surface of the support structure and a lower surface of the overhang geometry. The powder conducts heat from the overhang geometry to the support structure. The support structure acts as a heat sink to enhance heat transfer and reduce the temperature and severe thermal gradients due to poor thermal conductivity of metallic powders underneath the overhang. Because the support structure is not connected to the part, the support structure can be removed freely without any post-processing step.

Chou, Yuag-Shan↗
NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗
NASA NTRSDate not supplied

Design of a GRCop-42 Regeneratively Cooled Thrust Chamber Assembly and Feed System

An additively manufactured thrust chamber assembly was designed and printed using laser powder bed fusion. The NASA-developed material GRCop-42 was used for its high strength and high temperature characteristics. The combustion chamber and nozzle utilize regenerative coolant channels to achieve long duration hot fire tests. Design for additive manufacturing was used to create geometries not easily attainable with traditional machining. The thrust chamber assembly was post processed to ensure print quality and verify for testing. A feed system – encompassing all propellant lines, valves, sensors, and tanks – was designed and built to enable steady state, pressure regulated testing. Pressure transducers, thermocouples, and load cells were placed to enable measurements of the propellant properties and engine performance. Venturis and orifices were used throughout the system to control the flow rates to the thrust chamber. Aside from providing propellants, the feed system provides pressure using nitrogen, and purges the lines during shutdown. The design process for this testing platform is described. A testing campaign on the hardware will be conducted by the Akronauts Rocket Design Team at the University of Akron in Spring 2023.

Dillon M. Petty↗
NASA NTRS2016

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. The near-net shape DMLS parts have been delivered and final machining is underway. Fabrication of the traditionally manufactured hardware is also proceeding. Testing in liquid oxygen is planned for Q2 of FY2017. This topic explores the design of the turbopump along with fabrication and material testing of the DMLS hardware.

O'Neal, Derek↗
NASA NTRS2016

Applying Additive Manufacturing to a New Liquid Oxygen Turbopump Design

A liquid oxygen turbopump has been designed at Marshall Space Flight Center as part of the in-house, Advanced Manufacturing Demonstrator Engine (AMDE) project. Additive manufacturing, specifically direct metal laser sintering (DMLS) of Inconel 718, is used for 77% of the parts by mass. These parts include the impeller, turbine components, and housings. This paper discusses the impacts of the DMLS fabrication technique on the design of the turbopump and lessons learned during DMLS hardware fabrication and material testing.

O’Neal, T. Derek↗