Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffusers, Subsonic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Performance of an All-internal Conical Compression Inlet with Annular Throat Bleed at Mach Number 5.0

An all-internal conical compression inlet with annular bleed at the throat was investigated at Mach 5.0 and zero angle of attack. The minimum contraction ratio of the supersonic diffuser, coincident with a mass-flow ratio of 1.0, was determined to be 0.084 as compared with the isentropic contraction ratio of 0.04 at Mach 5.0. The over-all inlet performance was very sensitive to the amount of annular bleed at the throat because of the extensive boundary layer. For example, the critical recovery varied from 41 percent with 6-percent bleed to 59 percent with 25-percent bleed. Decreasing the spacing between the supersonic and subsonic diffusers increased the critical mass-flow ratio but reduced the range of subcritical mass-flow regulation. A constant-area section was required ahead of the subsonic diffuser in order to obtain reasonable performance. An inlet-engine net-thrust analysis indicated that the optimum performance occurred with from 20- to 25-percent bleed, depending on how the bypassed air was handled.

Stitt, Leonard E.↗
NASA NTRS1956

Zero-angle-of-attack Performance of Two-dimensional Inlets near Mach Number 3

An extensive program was undertaken to investigate the effect of several geometric variables on the performance of two-dimensional inlets. This investigation included inlets having single-wedge, double-wedge, and isentropic compression ramps with various side-plate configurations and subsonic diffusers. The tests were conducted over a range of Reynolds number based on inlet height from 0.50 to 2.67(sup x)10(sup 6). Generally, the performance levels of the two-dimensional inlets were somewhat below those obtained previously with comparable axisymmetric models. At Mach number 3.05 the optimum total-pressure recovery was obtained with an isentropic inlet which compressed the external flow to a Mach number of 1.88. Rectangular side plates and a long high-exit-Mach-number subsonic diffuser with filleted corners were used with this inlet. A critical total-pressure recovery of 0.71 was realized with a corresponding mass-flow ratio of 0.965. Subcritical stability to a mass-flow ratio of 0.60 was obtained.

Woollett, Richard R↗
NASA NTRSDate not supplied

CFD Simulation of an Inward-Turning Supersonic Inlet Unstart at Flight Mach Number 1.7

Interest in inward-turning supersonic inlets renewed during NASA’s Commercial Supersonic Technology Project, as a means of reducing disturbances caused by propulsion integration. Inward-turning designs have the potential to greatly reduce the strength of shock waves emanating outward from the nacelle, and therefore their contribution to the overall sonic boom signature. For top-mounted, or over-wing installations, disturbances to aircraft aerodynamics are reduced. The nature of the inward-turning geometry results in a boundary-layer thickening effect, opposite that of the familiar thinning of an outward-turning cone boundary-layer. The application of a small amount of boundary-layer bleed at the throat has been shown to alleviate the negative effects of the boundary-layer on subsonic diffuser performance. Boundary-layer bleed, however, comes at the expense of increased complexity, and external disturbances at bleed exits that would partially defeat the purpose of the inward-turning scheme. Vortex generators were proposed as an alternative to bleed, and an initial CFD study of their effectiveness in this application forms the basis of the present work. A source-term model in the Wind-US CFD code was used to model the effects of an array of vortex generators placed at the entrance to the subsonic diffuser. Baseline results with no vortex generators compared favorably to previously reported results with no bleed at back-pressures near the design point, but stability margin in the present case was limited by a curious non-linear phenomena similar to unstart in mixed-compression inlets. While some improvement was noted with vortex generators, their effectiveness was diminished by the limited stability margin. A time-accurate calculation was subsequently performed to better understand this process. Results of this calculation are presented and instantaneous solutions compared with steady-state, subcritical results previously reported. The stability margin limitation is attributed to the use of a constant-pressure outflow boundary condition, which differed from that used in the prior simulations.

Pre-Compressor Cooling, Water Injection, Hypersoni↗
NASA NTRS1956

A Theory for Stability and Buzz Pulsation Amplitude in Ram Jets and an Experimental Investigation Including Scale Effects

From a theory developed on a quasi-one-dimensional-flow basis, it is found that the stability of the ram jet is dependent upon the instantaneous values of mass flow and total pressure recovery of the supersonic diffuser and immediate neighboring subsonic diffuser. Conditions for stable and unstable flow are presented. The theory developed in the report is in agreement with the experimental data of NACA-TN-3506 and NACA-RM-L50K30. A simple theory for predicting the approximate amplitude of small pressure pulsation in terms of mass-flow decrement from minimum-stable mass flow is developed and found to agree with experiments. Cold-flow tests at a Mach number of 1.94 of ram-jet models having scale factors of 3.15:1 and Reynolds number ratios of 4.75:1 with several supersonic diffuser configurations showed only small variations in performance between geometrically similar models. The predominant variation in steady-flow performance resulted from the larger boundary layer in the combustion chamber of the low Reynolds number models. The conditions at which buzz originated were nearly the same for the same supersonic diffuser (cowling-position angle) configurations in both large and small diameter models. There was no appreciable variation in stability limits of any of the models when the combustion-chamber length was increased by a factor of three. The unsteady-flow performance and wave patterns were also similar when considered on a reduced-frequency basis determined from the relative lengths of the model. The negligible effect of Reynolds number on stability of the off-design configurations was not anticipated in view of the importance of boundary layer to stability, and this result should not be construed to be generally applicable. (author)

Trimpi, Robert L↗
NASA NTRS2024

SUPIN: A Tool for the Aerodynamic Design and Analysis of Supersonic Inlets

The Supersonic Inlet Design and Analysis Tool (SUPIN) is a computational program that performs geometric modeling and aerodynamic design and analysis of a set of supersonic inlets whose types include the axisymmetric pitot, three-dimensional pitot, axisymmetric, two-dimensional, two-dimensional bifurcated-duct, and streamline-traced inlets. The inlets are modeled by dividing the inlet flowpath into components that start at the freestream and ends at the engine face. The primary components of the inlet include the external supersonic diffuser, throat section, and subsonic diffuser. Each component is characterized by a set of inputs that include geometric and aerodynamic factors. Examples of the geometric factors are angles, lengths, area ratios, and coordinates that describe the geometry of the components. Examples of the aerodynamic factors are Mach numbers, flow ratios, and pressure ratios that set constraints or desired aerodynamic properties of the component. These input factors are specified within a text-based input data file that is read into SUPIN. SUPIN is a Fortran 95 program that performs the inlet design and analysis as a batch or non-interactive process. SUPIN writes output data files describing the inlet geometry and aerodynamic performance. SUPIN uses analytic, empirical, and numerical methods to perform the inlet design and analysis. The inlet geometry is constructed using planar and three-dimensional geometry constructs and is represented by coordinates, angles, areas, profiles, and surfaces. Surfaces are output in the form of a Plot3D surface grid file. SUPIN does have some capability to automatically generate planar and three-dimensional, multi-block, structured grids for computational fluid dynamics (CFD) analysis. The aerodynamic analysis performed by SUPIN computes quasi-one-dimensional properties, such as Mach numbers, pressures, and temperatures, through the inlet flowpath. Planar aerodynamic properties, such as those for shock and Mach waves, are computed for the supersonic compression of the external supersonic diffuser and throat section. The inlet performance is characterized by the inlet flow rates, total pressure recovery, and inlet drag. The primary intent of this document is to describe the usage of SUPIN. The methods used within SUPIN are documented and may serve as a useful reference for understanding the aerodynamic design and analysis of supersonic inlets.

supersonic inlets↗
NASA NTRS1973

Design and experimental performance of short curved wall diffusers with axial symmetry utilizing slot suction

The feasibility of designing short curved wall axially symmetrical subsonic diffusers utilizing suction through slots in the diffuser walls to prevent flow separation was investigated. A potential flow analysis was made, and a digital computer program was written for determining the diffuser wall contour for prescribed boundary conditions. The flow field included branch flow so that the suction slot geometry could be a part of the diffuser design. One bell shaped diffuser and three annular diffusers with area ratios of either 2.5:1 or 3:1 were designed, fabricated, and tested. Minimum suction requirements of metastable operation ranged from 6.3 percent to 12 percent when operating with inlet air velocities in the 1000 to 250 ft/sec (30 to 76 m/sec) range. For stable operation suction rates from 10 percent to 22 percent were required. In all cases the diffuser effectiveness was above 95 percent based on the conventional definition, and from 81 percent to 94 percent when the suction loss was accounted for. The exit velocity profiles were virtually flat with no more than + or - 9% variation over 95 percent of the exit area when operated with sufficient suction to prevent flow separation.

Yang, T.↗
NASA NTRS1996

A Computational-Experimental Development of Vortex Generator Use for a Transitioning S-Diffuser

The development of an effective design strategy for surface-mounted vortex generator arrays in a subsonic diffuser is described in this report. This strategy uses the strengths of both computational and experimental analyses to determine beneficial vortex generator locations and sizes. A parabolized Navier-Stokes solver, RNS3D, was used to establish proper placement of the vortex generators for reduction in circumferential total pressure distortion. Experimental measurements were used to determine proper vortex generator sizing to minimize total pressure recovery losses associated with vortex generator device drag. The best result achieved a 59% reduction in the distortion index DC60, with a 0.3% reduction in total pressure recovery.

Wendt, Bruce J.↗
NASA NTRS2020

Design Factors for Two-Dimensional, External-Compression Supersonic Inlets

Geometric and aerodynamic design factors were studied for the design of two-dimensional, external-compression inlets operating at a freestream Mach number of Mach 1.7. Computational simulations of the inlet flows were performed to obtain the inlet performance metrics consisting of the inlet flow rates, total pressure recovery, and total pressure distortion at the engine face. The key design factors identified included the external diffuser Mach number, cowl lip interior angle, bleed slot length, throat section aft centerbody slope, and subsonic diffuser length. Using the results of the Mach 1.7 inlet study, inlets were designed for Mach 1.4 and 2.0. The results provide useful insight on the significance of the design factors for the design of such inlets for commercial supersonic aircraft.

Slater, John W.↗
NASA NTRS1972

Effects of vane-induced rotation on diffuser flow distortion in an axisymmetric mixed-compression inlet

An investigation of vane-induced flow rotation to modify distorted steady-state total-pressure patterns in the subsonic diffuser of a supersonic mixed-compression inlet was conducted. Radial static-pressure gradients generated by the rotation was the mechanism used to modify the total-pressure distributions. Significant redistribution of circumferential distortion patterns into more compatible radial patterns was realized, but flow problems near the duct walls reduced the general effectiveness of the technique. Total-pressure losses associated with the swirl vanes were slight. Limited turbulence data indicated that vane istallation resulted in reduced turbulence levels.

Meleason, E. T.↗
NASA NTRS1957

Experimental evaluation of methods for improving diffuser-exit total-pressure profiles for a side-inlet model at Mach number 1.91

Distortion effects of the following model additions or changes were studied: (1) constant-area mixing lengths at the end of the subsonic diffuser, (2) screens with systematic variations in mesh and flow-area blockage, (3) bleeds slots on the inlet cowl, and (4) a simulated compressor hub. Data at a diffuser-exit Mach number of 0.36 are compared with data of a similar study at Mach 0.20. At the higher Mach number, the same length of constant-area mixing was less effective in reducing total-pressure distortions, while the use of screens was more effective.

Klann, John L↗
NASA NTRS1972

Dynamic flow angle measurements at the diffuser exit of a Mach 2.5 mixed compression inlet

An exploratory investigation was made to determine the magnitude of the dynamic flow angle at a single point in the diffuser exit of a Mach 2.50 inlet. Results indicate that the maximum flow angle variation was + or - 3 degrees except when vortex generators were installed in the subsonic diffuser. The amplitude of these flow angle fluctuations was directly related to the amplitude of the total pressure fluctuations at the probe survey point. Flow angle fluctuations as high as + or - 11 degrees were recorded when vortex generators were installed near the probe survey point.

Prati, W. M.↗
NASA NTRS1973

Pressure recovery performance of conical diffusers at high subsonic Mach numbers

The pressure recovery performance of conical diffusers has been measured for a wide range of geometries and inlet flow conditions. The approximate level and location (in terms of diffuser geometry of optimum performance were determined. Throat Mach numbers from low subsonic (m sub t equals 0.2) through choking (m sub t equals 1.0) were investigated in combination with throat blockage from 0.03 to 0.12. For fixed Mach number, performance was measured over a fourfold range of inlet Reynolds number. Maps of pressure recovery are presented as a function of diffuser geometry for fixed sets of inlet conditions. The influence of inlet blockage, throat Mach number, and inlet Reynolds number is discussed.

Dolan, F. X.↗
NASA NTRS1975

Experimental evaluation of a Mach 3.5 axisymmetric inlet

Wind tunnel test results for a large scale inlet model designed for Mach 3.5 are presented and compared with analytical predictions. The inlet is an axisymmetric mixed-compression type with a lip diameter of 49.723 cm. The inlet design was developed using analytical procedures. Data are shown for freestream Mach numbers from 0.6 to 3.5. The test results indicate that boundary layer bleed requirements can be accurately predicted. Good agreement was obtained with analytical predictions of the flowfield structure and boundary layer development in the supersonic diffuser yielding high performance at the design Mach number. The highest engine face total pressure recovery at Mach 3.5 was 85.8%; this was obtained at 0.05 Mach tolerance with only 2.8% total pressure distortion and 13.4% bleed. In the started Mach number range from 1.6 to 3.5, the total pressure recovery in the throat, downstream of the terminal normal shock, ranged between 91% and 95%. Total pressure losses in the subsonic diffuser varied from 3% to 13%. The higher losses occuring between Mach 2.5 and 3.2 were believed to be caused by the rapid rate of increase in the area of the diffuser just downstream of the throat, possibly coupled with inadequate centerbody throat bleed. In the unstarted mode at transonic speeds, the maximum inlet flow was over 99% of the theoretical maximum capture mass-flow.

Syberg, J.↗
NASA NTRS1983

Progress toward the analysis of supersonic inlet flows

A zonal flow analysis procedure was developed to predict the flow through the supersonic diffuser of an axisymmetric mixed compression inlet at angle-of-attack. In this analysis, the inlet flow is divided into three types of regions, each with different dominant flow phenomena. These are the inviscid supersonic core, boundary layer, and shock/boundary layer interaction flows. An appropriate analysis was selected or developed for the three-dimensional flow in each type of region. Procedures were developed to interface these analyses for the overall inlet flow analysis. This analysis was applied to an inlet operating at M = 2.58 at several angle-of-attack conditions. Comparisons are presented between computed and measured flow properties for the inlet and for the component analysis flows. Extensions of the present procedure to include the terminal shock and subsonic diffuser flows are recommended. Desirable experiments for evaluation of the inlet analysis procedure or the component analyses and to support improved modeling or extension of the inlet analysis are defined and recommended.

Paynter, G. C.↗