Search NASA⌕ Search

SEARCH · Search NASA

Results for “Direct drive”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Analytical Modeling of a Novel Transverse Flux Machine for Direct Drive Wind Turbine Applications

This paper presents a nonlinear analytical model of a novel double sided flux concentrating Transverse Flux Machine (TFM) based on the Magnetic Equivalent Circuit (MEC) model. The analytical model uses a series-parallel combination of flux tubes to predict the flux paths through different parts of the machine including air gaps, permanent magnets (PM), stator, and rotor. The two-dimensional MEC model approximates the complex three-dimensional flux paths of the TFM and includes the effects of magnetic saturation. The model is capable of adapting to any geometry which makes it a good alternative for evaluating prospective designs of TFM as compared to finite element solvers which are numerically intensive and require more computation time. A single phase, 1 kW, 400 rpm machine is analytically modeled and its resulting flux distribution, no-load EMF and torque, verified with Finite Element Analysis (FEA). The results are found to be in agreement with less than 5% error, while reducing the computation time by 25 times.

17 WIND ENERGY↗

Laser–plasma interactions in direct-drive ignition plasmas

Direct-drive ignition is most susceptible to multiple-beam laser–plasma instabilities, as the single-beam intensities are low (I s ~ 10 14 Wcm -2 ) and the electron temperature in the underdense plasma is high (Te 3.5 keV). Cross-beam energy transfer is driven by multiple laser beams and can significantly reduce the hydrodynamic efficiency in direct-drive experiments on OMEGA (Boehly et al 1997 Opt. Commun. 133 495). Reducing the radii of the laser beams significantly increases the hydrodynamic efficiency at the cost of an increase in the low-mode modulations. Initial 2D hydrodynamic simulations indicate that zooming, transitioning the laser–beam radius prior to the main drive, does not increase low-mode nonuniformities. The combination of zooming and dynamic bandwidth reduction will provide a 30% effective increase in the drive energy on OMEGA direct-drive implosions. It was shown that two-plasmon decay (TPD) can be driven by multiple laser beams and both planar and spherical experiments were performed to study the hot electrons generated by TPD. The fraction of laser energy converted to hot electrons scales with the hot-electron temperature for all geometries and over a wide range of intensities. At ignition-relevant intensities, the fraction of laser energy converted to hot electrons is measured to decrease by an order of magnitude when the ablator material is changed from carbon–hydrogen to aluminum. Finally, the TPD results are compared with a multiple-beam linear theory and a nonlinear Zakharov model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of two-plasmon decay in direct-drive inertial confinement fusion through the manipulation of ion-acoustic and Langmuir wave damping

The extended Zakharov model of the two-plasmon decay instability in an inhomogeneous plasma [D. F. DuBois et al., Phys. Rev. Lett. 74, 3983 (1995); D. A. Russell and D. F. DuBois, Phys. Rev. Lett. 86, 428 (2001)] is further generalized to include the evolution of the electron distribution function in the quasi-linear approximation [cf., e.g., K. Y. Sanbonmatsu et al. Phys. Plasmas 7, 2824 (2000); D. A. Russell et al., paper presented at the Workshop on SRS/SBS Saturation, Wente Vineyards, Livermore, CA, 2–5 April 2002]. This makes it possible to investigate anomalous absorption of laser light and hot electron production due to the two-plasmon decay instability of multiple overlapping electromagnetic waves. Scalings of hot-electron production in the (stationary) nonlinearly saturated regime relevant to recent experiments [B. Yaakobi et al., Phys. Plasmas 19, 012704 (2012); D. H. Froula et al., Phys. Rev. Lett. 108, 165003 (2012)] have been obtained. They indicate a sensitivity to ion-acoustic wave (IAW) damping and to the collisional absorption of Langmuir waves. Such a sensitivity might be exploited in inertial confinement fusion target design by the use of mid-Z ablators.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Comprehensive Review of Permanent Magnet Transverse Flux Machines for Direct Drive Applications

The use of direct drive machines in renewable and industrial applications are increasing at a rapid rate. Transverse flux machines (TFM) are ideally suited for direct drive applications due to their high torque density. In this paper, a comprehensive review of the permanent magnet (PM) TFMs for direct drive applications is presented. The paper introduces TFMs and their operating principle and then reviews the different type of TFMs proposed in the literature. The TFMs are categorized according to the number of stator sides, types of stator cores and magnet arrangement in the rotor. The review covers different design topologies, materials used for manufacturing, structural and thermal analysis, modeling and design optimization and cogging torque minimization in TFMs. The paper also reviews various applications and comparisons for TFMs that have been presented in the literature.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Crossed-beam energy transfer in direct-drive implosions

Direct-drive-implosion experiments on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have showed discrepancies between simulations of the scattered (non-absorbed) light levels and measured ones that indicate the presence of a mechanism that reduces laser coupling efficiency by 10%-20%. This appears to be due to crossed-beam energy transfer (CBET) that involves electromagnetic-seeded, low-gain stimulated Brillouin scattering. CBET scatters energy from the central portion of the incoming light beam to outgoing light, reducing the laser absorption and hydrodynamic efficiency of implosions. One-dimensional hydrodynamic simulations including CBET show good agreement with all observables in implosion experiments on OMEGA. Three strategies to mitigate CBET and improve laser coupling are considered: the use of narrow beams, multicolor lasers, and higher-Z ablators. Experiments on OMEGA using narrow beams have demonstrated improvements in implosion performance.

36 MATERIALS SCIENCE↗

Crossed-beam energy transfer in direct-drive implosions

Direct-drive-implosion experiments on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have showed discrepancies between simulations of the scattered (non-absorbed) light levels and measured ones that indicate the presence of a mechanism that reduces laser coupling efficiency by 10%-20%. This appears to be due to crossed-beam energy transfer (CBET) that involves electromagnetic-seeded, low-gain stimulated Brillouin scattering. CBET scatters energy from the central portion of the incoming light beam to outgoing light, reducing the laser absorption and hydrodynamic efficiency of implosions. One-dimensional hydrodynamic simulations including CBET show good agreement with all observables in implosion experiments on OMEGA. Three strategies to mitigate CBET and improve laser coupling are considered: the use of narrow beams, multicolor lasers, and higher-Z ablators. Experiments on OMEGA using narrow beams have demonstrated improvements in implosion performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laser-direct-drive program: Promise, challenge, and path forward

Along with laser-indirect (X-ray)-drive and magnetic-drive target concepts, laser direct drive is a viable approach to achieving ignition and gain with inertial confinement fusion. In the United States, a national program has been established to demonstrate and understand the physics of laser direct drive. The program utilizes the Omega Laser Facility to conduct implosion and coupling physics at the nominally 30-kJ scale and laser–plasma interaction and coupling physics at the MJ scale at the National Ignition Facility. This article will discuss the motivation and challenges for laser direct drive and the broad-based program presently underway in the United States.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Comprehensive Review of Permanent Magnet Transverse Flux Machines: Use in Direct-Drive Applications

The use of direct-drive machines in renewable and industrial applications is increasing at a rapid rate. Transverse flux machines (TFMs) are ideally suited for direct-drive applications due to their high torque density. This article presents a comprehensive review of permanent magnet (PM) TFMs for direct-drive applications. It introduces TFMs and their operating principle and reviews the different types of TFMs proposed in the literature. TFMs are categorized by the number of stator sides, types of stator cores, and magnet arrangement in the rotor. The review covers different design topologies, materials used for manufacturing, structural and thermal analyses, modeling, design optimization, and cogging torque minimization in TFMs. The article also examines various applications and comparisons for TFMs presented in the literature.

air gaps↗

The National Direct-Drive Inertial Confinement Fusion Program

The National Direct-Drive Inertial Confinement Fusion Program consists of the 100-Gbar Campaign on the 30-kJ, 351-nm, 60-beam OMEGA Laser System and the Megajoule Direct-Drive (MJDD) Campaign on the 1.8-MJ, 351-nm, 192-beam National Ignition Facility (NIF). The main goals of the 100-Gbar Campaign are to demonstrate and understand the physics for hot-spot conditions and formation relevant for ignition at the MJ scale, while the MJDD Campaign seeks to understand the laser-plasma interactions, energy coupling, and laser imprint for ignition-scale direct-drive coronal plasmas. An overview of the multi-year, systematic effort that is underway for the National Direct-Drive Inertial Confinement Fusion Program (including laser, target, and diagnostic improvements in progress), as well as recent results from the 100-Gbar Campaign on OMEGA and the MJDD Campaign on NIF is presented in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Direct Drive Hall Thruster System Development

The sta:us of development of a Direct Drive Ha!! Thruster System is presented. 13 the first part. a s:udy of the impacts to spacecraft systems and mass benefits of a direct-drive architecture is reviewed. The study initially examines four cases of SPT-100 and BPT-4000 Hall thrusters used for north-south station keeping on an EXPRESS-like geosynchronous spacecraft and for primary propulsion for a Deep Space- 1 based science spacecraft. The study is also extended the impact of direct drive on orbit raising for higher power geosynchronous spacecraft and on other deep space missions as a function of power and delta velocity. The major system considerations for accommodating a direct drive Hall thruster are discussed, including array regulation, system grounding, distribution of power to the spacecraft bus, and interactions between current-voltage characteristics for the arrays and thrusters. The mass benefit analysis shows that, for the initial cases, up to 42 kg of dry mass savings is attributable directly to changes in the propulsion hardware. When projected mass impacts of operating the arrays and the electric power system at 300V are included, up to 63 kg is saved for the four initial cases. Adoption of high voltage lithium ion battery technology is projected to further improve these savings. Orbit raising of higher powered geosynchronous spacecraft, is the mission for which direct drive provides the most benefit, allowing higher efficiency electric orbit raising to be accomplished in a limited period of time, as well as nearly eliminating significant power processing heat rejection mass. The total increase in useful payload to orbit ranges up to 278 kg for a 25 kW spacecraft, launched from an Atlas IIA. For deep space missions, direct drive is found to be most applicable to higher power missions with delta velocities up to several km/s , typical of several Discovery-class missions. In the second part, the status of development of direct drive propulsion power electronics is presented. The core of this hardware is the heater-keeper-magnet supply being qualified for the BPT-4000 by Aerojet. A breadboard propulsion power unit is in fabrication and is scheduled for delivery late in 2003.

Hoskins, W. Andrew↗

The National Direct-Drive Program: OMEGA to the National Ignition Facility

The goal of the National Direct-Drive Program is to demonstrate and understand the physics of laser direct drive (LDD). Efforts are underway on OMEGA for the 100-Gbar Campaign to demonstrate and understand the physics for hot-spot conditions and formation relevant for ignition at the 1-MJ scale, and at the National Ignition Facility to develop an understanding of the direct-drive physics at long scale lengths for the MJ Direct-Drive Campaign. For this paper the strategy of the National Direct-Drive Program is described; the requirements for the DT cryogenic fill-tube target being developed for OMEGA are presented; and preliminary LDD implosion measurements of hydrodynamic mixing seeded by laser imprint, the target-mounting stalk, and microscopic surface debris are reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Determining acceptable limits of fast-electron preheat in direct-drive-ignition–scale target designs

In direct-drive–ignition designs, preheat by fast electrons created by the two-plasmon–decay or stimulated Raman instabilities can increase the adiabat in the fuel layer and reduce compression and neutron yield. Since eliminating the preheat entirely is a major challenge, it is necessary to understand the levels of preheat that preclude ignition in a direct-drive target. Two 1-D ignition-scale target designs serve as the basis for examining the effects of synthetically increasing the levels of fast electrons using the 1-D radiation–hydrodynamic code LILAC , which includes two models of fast-electron transport. The first is an ignition design adapted from a 2-D polar-direct-drive (PDD) design for the National Ignition Facility (NIF). The second is derived from the first but uses a laser pulse that generates stronger shocks and a higher fuel adiabat. This more stable “alpha-burner” design approaches ignition and achieves yield multiplication as a result of alpha heating. The designs are then re optimized to recover performance. The igniting design, when fast-electron transport was modeled with diffusion, was found to tolerate 50% more fast-electron preheat of the cold (sub-50 eV) DT ice layer when the laser pulse was optimized using the optimizer Telios . When a straight-line fast-electron transport model was used, the effects of optimization were negligible. For the alpha-burner design, an increase of over a factor of at least 3 in the tolerable level of fast-electron preheat was obtained for both transport models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Three-dimensional hot-spot x-ray emission tomography from cryogenic deuterium–tritium direct-drive implosions on OMEGA

A three-dimensional model of the hot-spot x-ray emission has been developed and applied to the study of low-mode drive asymmetries in direct-drive inertial confinement fusion implosions on OMEGA with cryogenic deuterium–tritium targets. Here, the steady-state model assumes an optically thin plasma and the data from four x-ray diagnostics along quasi-orthogonal lines of sight are used to obtain a tomographic reconstruction of the hot spot. A quantitative analysis of the hot-spot shape is achieved by projecting the x-ray emission into the diagnostic planes and comparing this projection to the measurements. The model was validated with radiation-hydrodynamic simulations assuming a mode-2 laser illumination perturbation resulting in an elliptically shaped hot spot, which was accurately reconstructed by the model using synthetic x-ray images. This technique was applied to experimental data from implosions in polar-direct-drive illumination geometry with a deliberate laser-drive asymmetry, and the hot-spot emission was reconstructed using spherical-harmonic modes of up to ℓ = 3. A 10% stronger drive on the equator relative to that on the poles resulted in a prolate-shaped hot spot at stagnation with a large negative A 2,0 coefficient of A 2,0 = –0.47 ± 0.03, directly connecting the modal contribution of the hot-spot shape with the modal contribution in laser-drive asymmetry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Magnetostrictive direct drive motors

Developing magnetostrictive direct drive research motors to power robot joints is discussed. These type motors are expected to produce extraordinary torque density, to be able to perform microradian incremental steps and to be self-braking and safe with the power off. Several types of motor designs have been attempted using magnetostrictive materials. One of the candidate approaches (the magnetostrictive roller drive) is described. The method in which the design will function is described as is the reason why this approach is inherently superior to the other approaches. Following this, the design will be modelled and its expected performance predicted. This particular candidate design is currently undergoing detailed engineering with prototype construction and testing scheduled for mid 1991.

Naik, Dipak↗

Requirements and Capabilities for Fielding Cryogenic DT-Containing Fill-Tube Targets for Direct-Drive Experiments on OMEGA

Improving the performance of direct-drive cryogenic targets at the Omega Laser Facility requires the development of a new cryogenic system to (i) field non permeable targets with a fill tube, and (ii) provide a clean environment around the target. This capability is to demonstrate that imploding a scaled-down version of the direct-drive–ignition target for the National Ignition Facility (NIF) on the OMEGA laser will generate the hot-spot pressure that is needed for ignition; this will justify future cryogenic direct-drive experiments on the NIF. The paper describes the target, the cryogenic equipment that is being constructed to achieve this goal, and the proposed target delivery process. Thermal calculations, fill-tube–based target designs, and structural/vibrational analyses are provided to demonstrate the credibility of the design. This new design will include capabilities not available (or possible) with the existing OMEGA cryogenic system, with the emphasis being to preserve a pristinely clean environment around the target, and to provide upgraded diagnostics to characterize both the ice layer and the target’s surface. The conceptual design is complete and testing of prototypes and subcomponents is underway. The rationale and capabilities of the new design are discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Assess the key physics that underpins high-hydro coupling-efficiency in NDCX-II experiments and high-gain heavy ion direct drive target designs using proven hydro codes like HYDRA

The simulations provided in this milestone have solidified the theoretical underpinning of direct drive targets and also the ability to design experiments on NDCX II that will enhance our understanding of ion-beam hydrodynamic coupling, and thus be relevant to IFE. For the case of the IFE targets, we have studied hydro and implosion efficiency using HYDRA in ID, a starting point towards the goal of polar direct drive in geometry compatible with liquid wall chambers. Recent analysis of direct drive fusion energy targets using heavy ion beams has found high coupling efficiency of ion beam energy into implosion energy. However, to obtain optimal coupling, the ion energy must increase during the pulse in order to penetrate the outflowing ablated material, and deposit the energy close enough to the fuel so that the fuel achieves sufficient implosion velocity. We have computationally explored ID (radial) time dependent models of ion driven direct drive capsule implosions using the Arbitrary Lagrangian-Eulerian (ALE) code HYDRA, to help validate the theoretical analysis done so far, particularly exploring the effects of varying the ion energy and ion current over the course of the pulse. On NDCX II, experiments have been proposed to explore issues of ion penetration of the outflowing plasma over the course of the ion pulse. One possibility is to create a first pulse of ions that heats a planar target, and produces an outflow of material. A second pulse, {approx}10 ns after the first, of higher ion energy (and hence larger projected range) will interact with this outflow before reaching and further heating the target. We have investigated whether the change in range can be tailored to match the evolution of the ablation front. We have carried out simulations using the one-dimensional hydrodynamic code DISH and HYDRA to set parameters for this class of experiments. DISH was upgraded with an ion deposition algorithm, and we have carried out ID (planar) simulations. HYDRA was also used for ID (planar) and 2D (r,z) simulations of potential experiments. We have also explored whether similar physics could be studied using an energy ramp (i.e., a velocity tilt) rather than two separate pulses. We have shown that an optimum occurs in the macropulse duration (with fixed velocity tilt) that maximizes the shock strength. In the area of IFE target design we have continued to explore direct drive targets composed of deuterium-tritium fuel and ablator layers. We have extended our previous target designs at 0.44 MJ drive energy, gain 50, (50 MeV foot, 500 MeV main pulse, Rb ion, which requires a large number of beams due to a high beam space charge constraint) to a power plant scale 3.7 MJ drive energy, gain {approx}150 (220 MeV foot, 2.2 GeV main pulse, Hg ion) that eases requirements on the accelerator. We have studied the effects of two important design choices on ICF target performance. We have shown that increasing the number of foot pulses may reduce the target's in-flight adiabat and consequently improve its compressibility and fusion yield. As in the case of laser drive, the first three shocks are the most important to the target's performance, with additional shocks contributing only marginally to compression and burn. We have also demonstrated that ion range lengthening during the main pulse can further reduce the target adiabat and improve the efficiency with which beam energy is coupled into the target. (Ion range lengthening using two different kinetic energies for the foot and main pulse has previously proven effective in the design of high gain targets).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhanced sensitivity to target offset when using cross-beam energy transfer mitigation techniques in direct-drive inertial confinement fusion implosions

In direct-drive inertial confinement fusion, target offset from the target chamber center (or center of beam convergence) may lead to significant implosion asymmetry and fusion yield degradation. In addition, cross-beam energy transfer (CBET) has been shown to be a significant source of laser energy scattering and leads to a reduction in implosion velocity and yield. To improve energy coupling and implosion performance, several techniques for CBET mitigation have been proposed. Recent simulations, however, have shown that CBET also substantially mitigates the effect of target offset on implosion asymmetry and yield [Anderson et al., Phys. Plasmas 27, 112713 (2020)]. Furthermore, the inclusion of CBET models in radiation-hydrodynamics codes was shown to greatly improve agreement between simulations and experiments involving substantial target offset distances. This paper explores the intensity dependence of this CBET–offset effect. In addition, it is shown that enhanced sensitivity to target offset can be expected when CBET-mitigation techniques are used in direct-drive implosions. This is shown through simulations of two such CBET-mitigation techniques on the OMEGA laser: (1) decreased beam-to-target radius, and (2) beam-to-beam frequency detuning. For the typical target offset distances (<15 μm) observed in experiments on OMEGA, however, overall yield is still anticipated to be substantially higher when CBET-mitigation techniques are employed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Testing of an Arcjet Thruster with Capability of Direct-Drive Operation

Electric thrusters typically require a power processing unit (PPU) to convert the spacecraft provided power to the voltage-current that a thruster needs for operation. Testing has been initiated to study whether an arcjet thruster can be operated directly with the power produced by solar arrays without any additional conversion. Elimination of the PPU significantly reduces system-level complexity of the propulsion system, and lowers developmental cost and risk. The work aims to identify and address technical questions related to power conditioning and noise suppression in the system and heating of the thruster in long-duration operation. The apparatus under investigation has a target power level from 400-1,000 W. However, the proposed direct-drive arcjet is potentially a highly scalable concept, applicable to solar-electric spacecraft with up to 100's of kW and beyond. A direct-drive electric propulsion system would be comprised of a thruster that operates with the power supplied directly from the power source (typically solar arrays) with no further power conditioning needed between those two components. Arcjet thrusters are electric propulsion devices, with the power supplied as a high current at low voltage; of all the different types of electric thruster, they are best suited for direct drive from solar arrays. One advantage of an arcjet over Hall or gridded ion thrusters is that for comparable power the arcjet is a much smaller device and can provide more thrust and orders of magnitude higher thrust density (approximately 1-10 N/sq m), albeit at lower I(sub sp) (approximately 800-1000 s). In addition, arcjets are capable of operating on a wide range of propellant options, having been demonstrated on H2, ammonia, N2, Ar, Kr, Xe, while present SOA Hall and ion thrusters are primarily limited to Xe propellant. Direct-drive is often discussed in terms of Hall thrusters, but they require 250-300 V for operation, which is difficult even with high-voltage solar arrays. The arcjet requires under 100 V, which is more in-line with what is easily possible with a solar array. Direct-drive of an electric propulsion system confers the advantage of reducing or eliminating the power processing unit (PPU) that is typically needed to convert the spacecraft-provided power to the voltage and current needed for thruster operation. Since the PPU is typically the most expensive piece of an electric thruster system, from both a fabrication and qualification standpoint, its elimination offers the potential for major reductions in system cost and risk. The design of the arcjet built for this effort was based on previous low power (1 kW class) arcjets. It has a precision machined 99.95% pure tungsten anode which also serves as the nozzle. The anode constrictor region is 1 mm (0.040-in) diameter and 1 mm (0.040-in) long. The cathode is a tungsten welding electrode doped with LaO2; its tip was precision ground to a 30◦ angle ending in a blunt end. The two electrodes are separated by a boron-nitride insulator which also serves as the propellant injection manifold; it ends in six small holes which introduce the propellant gas in the diverging section of the nozzle, directly adjacent to the cathode. The electrodes and insulator are housed in a stainless-steel outer-body, with a Macor insulator at the mid-plane to provide thermal isolation between the front and back halves of the device. The gas seals were made using Grafoil gaskets. Figure 1A shows the assembled thruster in the vacuum chamber; figure 1B shows the thruster in operation on argon at a flow rate of 676 sccm (20 mg/s). Initial testing was conducted in a 3.5-ft diameter vacuum chamber; the ultimate pressure reached during quasi-steady operation of the thruster was about 330 millitorr. The thruster was powered with a high-current, 0-100A, 15 kW power supply. The discharge was initiated with a high-voltage (approximately 10 kV) spark initiator that was isolated from the supply by a stack of diodes. The testing indicated that an operating point exists within the I-V characteristics that is compatible with direct-drive solar-electric operation; for a flow rate of 20 mg/s (argon) the arc could be sustained at a voltage of about 20 V and a current of 25 A (500W).

Martin, Adam K.↗