Search NASA⌕ Search

SEARCH · Search NASA

Results for “EDX++”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Oxidation of glucose to glycolic acid using oxygen and pyrolyzed spent Li-ion battery electrode material as catalyst

A search for non-noble catalysts for biomass processing led to the discovery that pyrolyzed electrode coating of spent Li-ion batteries can be used as an excellent catalyst for oxidation of D-glucose to glycolic acid. New no/low-cost catalyst was prepared by pyrolyzing black electrode coatings of 18,650 Li-ion cells from a spent DELL 1525 laptop battery at 600 ºC. Catalyst was characterized using SEM, EDX and X-ray and was shown to contain lithium nickel manganese cobalt oxide (Li a Ni b Mn c Co d O e ) on carbon with Ni: Mn: Co 4.12: 2.10: 1.50. Here, the catalytic activity of this material was evaluated for oxidation of D-glucose in aq. NaOH and water; glycolic, tartaric, malic, succinic and 2-hydroxybutaric acid were identified as key degradation products. The highest glycolic acid yield of 94% was obtained for oxidation of D-glucose under 3.4 Atm. oxygen, 120 °C, 2.0 h in 0.5 M aq. NaOH using 10 g catalyst/mol glucose.

25 ENERGY STORAGE↗
DOE OSTI2022

Thermodynamic re-modelling of the Cu–Nb–Sn system: Integrating the nausite phase

Currently available Cu–Nb–Sn phase diagrams lack the recently discovered nausite phase (Cu,Nb)Sn 2 , which is an important intermediate in the course of thermal processing of superconducting Nb 3 Sn wires. Processing decisively determines the resulting microstructure of Nb 3 Sn and, thus, its superconducting properties. Lack of suitable and complete phase diagrams, however, obstructs rational design of such thermal processing procedures. To close this gap and to obtain valid knowledge of homogeneity and stability range of nausite, various Cu–Nb–Sn samples, which are heat-treated between 300 °C and 500 °C, are investigated. By means of energy-dispersive X-ray spectroscopy (EDX), a temperature-dependent homogeneity range of nausite is observed, which covers average mole fractions of Cu between 0.09 and 0.15. This is correlated with a change in the mean atomic volume and can be seen in the lattice parameters determined by X-ray diffraction (XRD). Additionally performed first-principles calculations on different CuSn 2 and NbSn 2 model structures confirm this trend. Furthermore, the peritectic decomposition of nausite to NbSn 2 and liquid at 586 °C is determined by means of in situ XRD and differential scanning calorimetry (DSC). By using the CALPHAD (CALculation of PHase Diagrams) approach, all these findings are used to extend a previous thermodynamic description of the Cu–Nb–Sn system by including the nausite as an additional phase. Finally, with this noteworthy integration, the updated modelling of the Cu–Nb–Sn system can be used for optimizing the multistage heat-treatment steps during processing superconducting Nb 3 Sn wires.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Development of ceria-supported metal-oxide (MO x /CeO 2 ) catalysts via a one-pot chemical vapor deposition (OP-CVD) technique: Structure and reverse water gas shift reaction study

Current synthesis techniques for metal oxide (MO x )-supported catalysts have certain limitations of undesired target loading, ineffective dispersion of active species over the surface, uncontrolled particle size of active species, and complicated synthesis steps. Here, we developed a one-pot chemical vapor deposition (OP-CVD) methodology; by using which a solid metal precursor forms a vapor in a controlled condition and gets supported over the surrounding matrix. The theoretical stability followed by experimental validation using TGA is crucial for selecting the metal precursors. Three simple steps viz. premixing, dispersion, and rapid fixation by calcination are involved in the catalyst development via the OP-CVD approach. This study solely focused on the synthesis of 3d transition MO x over ceria support. The physicochemical characterizations of the prepared catalysts were performed by XRD, ICP-OES, SEM-EDX, CO pulse chemisorption, XANES, and EXAFS analyses to understand the crystal structure of involved species, target metal loading, dispersion, and particle size and prove the feasibility and viability of OP-CVD. The prepared catalysts were further tested for reverse water gas shift (RWGS) reaction to link their structural information with activity. The RWGS reaction data showed that the CO activity and CO selectivity were metal - and metal precursor-dependent. Higher CO activity of > 0.1 mol/h g-cat was observed for Cu and Co-based catalysts, with CO selectivity of ~100 %. This study provides an opportunity to produce efficient supported catalysts in a convenient way, providing effective catalytic activity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Uptake of aqueous heavy metal ions (Co2+, Cu2+ and Zn2+) by calcium-aluminium-silicate-hydrate gels

Highlights: • C-A-S-H gels containing metal ions (Co{sup 2+}, Cu{sup 2+} or Zn{sup 2+}) were precipitated by a sol-gel technique. • Uptake mechanism and immobilization capacity of divalent metal ions by C-A-S-H are elucidated. • Up to ~55–60 mol% of Zn can be incorporated in defective tobermorite-type C-A-S-H. • Metal uptake by C-A-S-H is controlled mainly by isomorphous substitution for Ca ions. • Crystal-chemical features of C-A-S-H gels and implications for practical application are discussed. Calcium-aluminium-silicate-hydrate (C-A-S-H) gels containing heavy metal ions (Me: Co{sup 2+}, Cu{sup 2+} or Zn{sup 2+}) were precipitated at different Me/Si molar ratios to study the uptake mechanism and immobilization capacity. Aqueous solution chemistry and solid-phase characterization using XRD, FTIR, ESEM-EDX, TEM-HAADF and TG-DSC methods reveal threshold values for ion substitution of ~55–60 mol% for Zn, ~30–40 mol% for Co and ~25–30 mol% for Cu in defective tobermorite-type C-A-S-H with (Ca + Me)/(Si + Al) molar ratios from 0.86 to 1.04. At higher aqueous Me concentrations, Me (chloride) hydroxides start to co-precipitate. The uptake mechanism of Me ions by C-A-S-H is based on (i) isomorphous substitution of Me for Ca in the CaO layer, (ii) ion exchange in the interlayer, (iii) tetrahedral substitution (Zn) within the dreierketten chains and (iv) surface adsorption onto the C-A-S-H gel structure. Systematics in crystal-chemistry of Me-bearing C-A-S-H and implications for application and performance in natural and man-made settings are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Simulation of radiation damage via alpha decay in BFS:PC grouts using 4 He 2+ ion acceleration

The impact of alpha radiation on cements used to encapsulate intermediate-level waste (ILW) is not well understood. ILW wastes can contain high levels of alpha-emitting radionuclides, meaning that the grouts used to encapsulate them are exposed to significant ionising radiation. Thus, a damaged region could develop in the grout adjacent to the alpha-emitting species. This work attempted to recreate this behaviour through nonradioactive 4 He 2+ ion-accelerator experiments, which have not previously been applied to common encapsulation grouts. The influence of this irradiation on a slag-Portland cement was investigated at different ages via transmission electron microscopy energy-dispersive x-ray spectroscopy (TEM-EDX) and supporting techniques, to assess whether 4 He 2+ irradiation caused textural or chemical zonation. No significant changes in hydrate phases or textures were observed, other than minor variations associated with carbonation. This paper provides a proof of concept for using ion acceleration techniques on cements and furthers knowledge on their radiation response.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High Temperature Oxidation Behavior of Aluminized Haynes 230

The effect of reactive air aluminizing (RAA) on the high-temperature oxidation behavior of the H230 superalloy is studied at 850 °C for 600 hours. Mass gain values are measured and microstructure is studied by XRD, SEM, and EDX. Post oxidation mass gain for the aluminized alloy is reduced compared to wrought alloy. A three-zone microstructure of diffusion coating is observed in RAA H230. Formation and growth of alumina scale during RAA process and oxidation is attributed to the complementary roles of ß-NiAl + ?'-Ni3Al phases in the composite coating.

Rashidi, S↗
DOE OSTI2022

Spectroscopic investigation of historical uranium glasses

Here, we present spectroscopic investigations of uranium in two historical glasses. A 1920's-1930's Art Deco (Bagley Carnival) green soda-lime-silica uranium glass bowl and a 1930's-1940's (Thomas Webb) yellow full lead crystal uranium glass vase were studied using optical absorption spectroscopy, XRF and SEM-EDX, X-band EPR and High- Energy Resolution Fluorescence-Detected (HERFD)-XANES. Uranium speciation may be different in the two glasses. Uranium occurs as uranyl groups (UO 2 2+ ) with minority reduced uranium species, mostly as U(V), more important in the Webb glass than in the Bagley glass. The differences between the two glasses arise from the fining procedure and result from the presence of other multivalent elements and differences in base glass composition. Electron Paramagnetic Resonance (EPR) spectra show the presence of an incipient signal close to g~2, partially annealed by heating to 550 °C, which we assign to a small concentration of radiation-induced defects caused by uranium decay. The presence of multivalent glass components in addition to U (As + Cu + Fe in the Bagley glass and Sb + Fe in the Webb glass) can trap the electron-hole pairs generated by the presence of uranium. This may explain the weakness of this signal in these glasses that anyway received a limited radiation dose since their fabrication. The low activity of these glasses, close to the background radiation, confirms that there is no danger to exhibiting them in museums.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Investigating the durability of a direct methanol fuel cell equipped with commercial Platinum Group Metal-free cathodic electro-catalysts

For the first time a long-term (500 h) durability study in direct methanol fuel cells (DMFCs) is carried out on a Platinum Group Metal-free (PGM-free) cathodic electro-catalyst commercially available on market. The electro-catalyst is tested for 500 h at a fixed cell voltage (0.3 V), recording the polarization curves during the operation. A drastic decrease in performance is observed after the first 100 h (from 220 to 75 mA cm –2 ); afterwards, the decrease is flatter, passing from 75 to 25 mA cm –2 (at 500 h). The causes of this performance degradation are investigated by postmortem physicochemical analyzes, such as X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and scanning electron microscopy (SEM) with X-ray energy dispersive analysis (EDX). Finally, possible reasons of degradation are indicated to be PGM-free catalyst aggregation, carbon and nitrogen species decrease, Ruthenium dissolution and migration from the anode to the cathode, poisoning both membrane and cathode catalyst.

25 ENERGY STORAGE↗
DOE OSTI2022

Assessment of lignite upgrade and hydrogen evolution via electrolysis

Lignite, considered as the lowest-rank coal, accounts for 45% of the total coal resources worldwide, and its low carbon and high ash contents limit its large-scale application. In order to upgrade lignite effectively, a modified coal electrolytic cell (MCEC) was designed, built, and then evaluated for lignite upgrade and hydrogen production through electrolysis, and the operating conditions were optimized. The results show that the performance of the MCEC outperformed the previous coal electrolytic cell (CEC). The operating temperature and iron concentration significantly impact the average current density per milligram of catalyst (ACDMC). The content of dry fixed carbon and heating value increased by 20.9% (wt%) and 8.15%, respectively, in electrolyzed lignite compared with raw lignite. Besides, 71.5% ash and 39.6% mercury were removed from raw lignite after electrolysis, which is the first report. The Faradaic efficiency (FE) for hydrogen evolution reached 99% using MCEC. In addition, the analysis of spectroscopy methods (SEM, EDX, FTIR, and XRD) revealed that the lignite particles were cracked; the oxygen-containing functional groups increased; the minerals of quartz and hematite formed on the surface of lignite particles after electrolysis. Furthermore, the facts indicate that electrolysis of lignite is a competitive approach for lignite upgrade and hydrogen production.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Characterization and recovery of rare earth elements and other critical metals (Co, Cr, Li, Mn, Sr, and V) from the calcination products of a coal refuse sample

Here, the impacts of calcination on the leaching recovery of rare earth elements (REEs) and other critical metals from a Baker seam coal refuse material were investigated. Acid leaching test results showed that leaching recovery of the REEs, especially the light REEs, was increased significantly from around 24% to 80–90% after calcination under 600–750 °C for two hours. By considering the major element leaching kinetics and the mineralogical changes of the dominant minerals caused by calcination, two mechanisms were proposed for the improved leaching performance: (1) decomposition of difficult-to-dissolve REE-bearing minerals into soluble forms; and (2) liberation of REE-bearing minerals encapsulated in clays after calcination due to the dehydration and disintegration of the layered clay structure. Sequential chemical extraction tests showed that a significant fraction (around 75%) of the REEs in the raw material were present in an insoluble form. After calcination under proper temperatures (600–800 °C), the majority of the insoluble light REEs (LREEs) were converted into soluble forms. Changes in the modes of occurrence of the LREEs and phosphorous based on leaching rate and sequential leaching correlated well as a function of the calcination temperature. This finding in addition to SEM-EDX results tends to indicate the potential that the LREEs occur primarily as rare earth phosphates such as monazite in the untreated coal refuse material. The acid leaching and sequential chemical extraction results show that co-extraction of REEs and other critical metals such as Co, Mn, and Li is possible using a calcination-acid leaching procedure.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Influence of microstructure on replacement and porosity generation during experimental dolomitization of limestones

Replacement reactions commonly alter the multiscale pore structures of rocks during fluid-rock interactions. Analysis of these processes in various model fluid-rock systems during controlled laboratory experiments provides insights into the origins of microstructures found in natural materials. This study focused on understanding the effects of initial starting material permeability and resultant differences in transport pathways on porosity and mineralogical changes during limestone dolomitization.A series of replacement experiments (32–317 days in duration) have been conducted in which 1.59 cm (5/8 in.) diameter cores of two different limestones were reacted with saturated MgCl2 solutions at 200 °C. The Texas Cream (Austin Chalk) is a high-porosity, high-permeability limestone, whereas both the porosity and permeability of the Carthage Marble (Burlington Limestone) are relatively low. Altered limestones were imaged using scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), Time-of-Flight Secondary Ion Mass Spectrometry (ToF–SIMS) and electron microprobe analysis (EMPA). A representative grain boundary of the low-porosity limestone was targeted for a focused ion beam (FIB) lift-out and characterized using transmission electron microscopy (TEM). These results were coupled with analyses of radial changes in the porosity distribution of the core derived from X-ray and neutron small- and ultra-small angle scattering ((U)SANS/(U)SAXS).The high-porosity/permeability limestone showed a four times faster bulk replacement rate than the lower-porosity/permeability material, and a different mechanism of porosity development. For the low-porosity limestone, a two-stage replacement occurred, with the reacted region of the core consisting of an inner rim in which the limestone was replaced by two calcite-dolomite solid solutions, and an outer rim in which the dolomite was replaced by magnesite. Elongated pores formed along grain boundaries at the initial limestone/dolomite reaction interface, and additional nanometer-scale porosity was formed at the secondary magnesite replacement rim. Grain boundaries were identified as preferential pathways for transport leading to dolomitization and a grain boundary diffusion rate was calculated based on microstructural characterization. In contrast, replacement in the high-porosity limestone was accompanied by porosity generation through replacement of individual grains by dolomite throughout the sample and, in longer runs, magnesite in outer parts of the core. These observations emphasize that both the mechanisms of the replacement reaction and the microstructure and chemistry of the replaced product are contingent on the initial structure of the starting material.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Uranium sorption to organic matter and long-term accumulation in a pristine alpine wetland

Understanding the controls on uranium (U) mobility in the environment is key to improve the management of sites contaminated by U mining activities. Previous research has shown that natural or engineered wetlands are particularly able to scavenge high amounts of U(VI) and U(IV) under noncrystalline forms. However, questions remain on the respective roles of sorption and reduction processes in the removal of U from running waters in wetlands, as well as on the long-term stability of U storage. Here, we performed a series of geochemical, isotopic ($δ$ 238 U, ( 234 U/ 238 U)), microscopic (SEM-EDXS, EPMA) and spectroscopic (µ-XRF, µ-XAS, XANES and EXAFS at the U L 3 and M 4 -edges and Fe K-edge) investigations to determine the modes of U accumulation and assess U mobility in a natural exceptionally U-enriched (up to 5000 µg/g) wetland on the shore of Lake Nègre (Mediterranean Alps, France). Uranium (VI) was largely dominant in the two studied soil cores, except a few samples containing as much as ~50 % U(IV). At the particle scale, U is associated to a variety of organic constituents of the soil matrix with a homogenous oxidation state. Bulk EXAFS spectroscopy at the U L 3 -edge shows that U is mostly mononuclear, with dominant monodentate binding to organic moieties (C neighbors at ~3.45 Å). An additional minor fraction of U under polymeric forms is inferred from wavelet (CCWT) analysis of the EXAFS data. These observations are reinforced by 1 M bicarbonate extractions that result in the dissolution of 82–96 % of total U, including putative polymeric species. At the wetland scale, similar or slightly fractionated isotopic ratios ($δ$ 238 U) between the wetland-feeding creek waters and the wetland soils are observed, supporting the idea that U(VI) sorption on organic matter is the primary U scavenging mechanism. Furthermore, it indicates that partial U(VI) reduction to U(IV) occurs as a second step, after sorption. Analysis of U decay chain disequilibria in the cores as a function of depth suggests that U accumulation in this wetland has lasted for several thousand years. In conclusion, we propose that the wetland acts as an active reactor where U has been massively accumulating for ~14500 years, especially as U(VI) forms associated to organic matter and is further partly exported to the lake through soil erosion.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2023

Improved catalytic activity of Mo x Ni y Al z thin films as electrocatalyst for hydrogen evolution reaction in alkaline media

In this work, we report activities of Mo x Ni y X z (where X is Al, Co, Cr, Cu, Fe, W)-based electrocatalysts for hydrogen evolution reaction (HER) in a 1 M NaOH solution. Mo x Ni y X z thin film electrocatslysts were prepared by magentron sputtering at 25°C and 800°C and characterized by scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analyzer and X-ray diffraction (XRD) analysis. Here, the catalytic activity of electrocatalyst was studied by cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalyst based on Mo 80 Ni 5 Al 15 (800°C) shows the best value of the overpotential (-181 mV) for HER from all tested ternary systems. XRD analysis indicates that HER activity only Mo 80 Ni 5 Al 15 thin films prepared at 800°C contained fcc phase. Other less active composition contained only bcc phase. The results obtained from impedance spectroscopy are consistent with the results from cyclic voltammetry. The stability of the prepared catalyst was studied by chronoamperometric analysis. The results from chronoamperometry show that HER activity of Mo 80 Ni 5 Al 15 prepared at 800°C, after very slight initial activity decrease, stays constant, while activity of Ni catalyst decreased almost twice in measured time window. Since Ni is commonly used industrial catalyst, Mo 80 Ni 5 Al 15 based alloy could be more attractive catalyst material for alkaline electrolyzers.

08 HYDROGEN↗
DOE OSTI2022

From ammonium Hexahalorhenates(IV) to nanocrystalline rhenium metal: A combined thermal, diffraction and microscopic analysis

Rhenium metal powder is a material of industrial importance. Several industrial and laboratory methods have been developed for the preparation of ultrafine Re metal powder and nanoparticles. The present study provides a better understanding of the characteristic and formation of Re metal powder from the decomposition of (NH4)2ReX6 salt (X = F, Cl, Br, I) at high temperature in inert atmosphere. Such analysis resulted in the formation of nanocrystalline Re metal as characterized by powder XRD. Williamson-Hall, Scherrer, and Williamson-Smallman methods were employed to study the effect of crystallize size, lattice strain, and dislocation density as analyzed from powder XRD peak broadening. Here, the morphology and composition of the metal were analyzed using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Elucidating the role of surface species in CO oxidation catalyzed by boron nitride nanotube supported transition metal oxides

Boron nitride nanotube (BNNT) is considered a highly promising catalyst support due to its outstanding thermal stability and chemical inertness. These characteristics make BNNT an attractive alternative for high-temperature applications. However, most studies to date have focused on incorporating platinum group metals (PGMs) to achieve high activity. Although BNNT-supported PGM catalysts are highly effective, their scarcity and high cost hinder widespread use in industrial processes. In this study, BNNT-supported transition metal oxides (TMO x /BNNT; TM = Fe, Co, Ni, and Cu) catalysts were investigated, and CO oxidation was applied as a model reaction to evaluate their catalytic performance. Several characterization techniques, including SEM-EDX, TEM, SXRD, H 2 -TPR, and XPS, were employed to examine their physicochemical properties. Notably, the particle size of the metal oxides differed significantly depending on the metal type. This variation is primarily attributed to the inherent metal–support interactions and the thermodynamic stability of each oxide during synthesis. These properties also affected catalytic activity, and various parameters, such as oxygen mobility and redox behavior, played important roles in determining performance. Finally, in situ DRIFTS, CO-TPSR, reaction-order analysis, and 18 O 2 isotope-labeling experiment were used to investigate the reaction mechanism. In conclusion, the findings provide insights into the design of cost-effective BNNT-supported catalysts and highlight their potential applicability in oxidation reactions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Low-pressure methanol synthesis from CO 2 over metal-promoted Ni-Ga intermetallic catalysts

Ni-Ga and M-Ni-Ga (M = Au, Co, Cu) catalysts were evaluated for methanol synthesis from CO 2 at 10 bar and 200-270°C. The following trend in turnover frequency (TOF) for CO 2 hydrogenation was observed: AuNiGa > CuNiGa > NiGa > CoNiGa, where TOF increased with decreasing catalyst affinity for CO. The presence of a third metal was found to influence both the formation of the Ni-Ga intermetallic phase as well as the number of available sites for CO chemisorption. Phase formation, catalyst composition and stability were evaluated using therm ogravimetric analysis (TGA), X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning transmission electron microscopy and energy dispersive X-ray spectroscopy (STEM-EDX). Au-Ni-Ga, which showed a nearly 4-fold improvement in TOF at 263°C and 10 bar compared to Ni-Ga, consisted of Ni 3 Ga particles decorated with Au, as evidenced by post catalysis characterization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Tensile behavior and microstructural evolution of a Fe-25Ni-20Cr austenitic stainless steel (alloy 709) from room to elevated temperatures through in-situ synchrotron X-ray diffraction characterization and transmission electron microscopy

Uniaxial tensile tests were done on Fe-25Ni-20Cr Austenitic Stainless Steel (Alloy 709) along with in-situ synchrotron measurement at different temperatures (25 degrees C, 500 degrees C, 700 degrees C and 900 degrees C). The X-Ray diffraction data was collected in-situ in order to follow the phases present as well as to derive the dislocation density as a function of strain through peak broadening analysis based on the modified Williamson-Hall method and see how trends are affected as a function of temperature. The XRD data were complemented by TEM and STEM-EDX characterization done on the post-experiment samples to observe the deformed microstructures. Finally, the paper presents a depiction of the tensile behavior of this advanced steel by interpreting the stress-strain curves and the effect of temperature through the information gained by in-situ XRD and TEM observations as well as fractography done ex-situ on the samples tested to rupture.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Design and characterization of hierarchical aluminosilicate composite materials for Cs entrapment: Adsorption efficiency tied to microstructure

The growing quantity of nuclear waste and the serious threats to the environment challenge researchers to innovate and target new waste form technologies. In the past decades, considerable efforts have been devoted to developing highly selective sorbents followed by safe disposal with the assurance of chemical stability and robust retention performance. Zeolite-containing geopolymers are regarded as a possible 2-in-1 material able to both capture and sequester elements such as Cs in bed fixed column application perspective. Here, these composites show promise for combining extraction properties of zeolite powder due to its crystalline structure (high capacity and selective adsorption), with the tunable microstructure and the shaping feasibility of the geopolymer binder. For the development of materials devoted to Cs immobilization, porous zeolite/geopolymer composites were prepared by dispersing NaY zeolite particles in a geopolymer binder. The influence of the structural properties of such composites on their ability to entrap a large amount of Cs by an ionic exchange process was notably studied. Composites' compositions, porosities, morphologies and crystallinity were analyzed by scanning electron microscopy coupled with energy dispersive x-ray spectroscopy (SEM-EDX), x-ray diffraction analysis (XRD) and nitrogen adsorption/desorption studies. Experimental Cs sorption in batch mode was used to follow the ionic exchange phenomenon in these materials. Along with 5 wt% amount of zeolite in geopolymer improves the Cs adsorption performance offering multiple new adsorption sites. Additionally, the geopolymer mesopores are beneficial facilitating the access of Cs and its role as a binder is advantageous to tailor granular hierarchical structure for safer industrial application.

36 MATERIALS SCIENCE↗