Search NASA⌕ Search

SEARCH · Search NASA

Results for “Edge localized modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3

Cross Flow Effects on Glaze Ice Roughness Formation

The present study examines the impact of large-scale cross flow on the creation of ice roughness elements on the leading edge of a swept wing under glaze icing conditions. A three-dimensional triple-deck structure is developed to describe the local interaction of a 3 D air boundary layer with ice sheets and liquid films. A linear stability analysis is presented here. It is found that, as the sweep angle increases, the local icing instabilities enhance and the most linearly unstable modes are strictly three dimensional.

Tsao, Jen-Ching↗

Flame Spread Along Free Edges of Thermally Thin Samples in Microgravity

The effects of imposed flow velocity on flame spread along open edges of a thermally thin cellulosic sample in microgravity were studied experimentally and theoretically. In this study, the sample was ignited locally at the middle of the 4 cm wide sample, and subsequent flame spread reached both open edges of the sample along the direction of the flow. The following flame behaviors were observed in the experiments and predicted by the numerical calculation, in order of increased imposed flow velocity: (1) ignition but subsequent flame spread was not attained, (2) flame spread upstream (opposed mode) without any downstream flame, and (3) the upstream flame and two separate downstream flames traveled along the two open edges (concurrent mode). Generally, the upstream and downstream edge flame spread rates were faster than the central flame spread rate for an imposed flow velocity of up to 5 cm/s. This was due to greater oxygen supply from the outer free stream to the edge flames and more efficient heat transfer from the edge flames to the sample surface than the central flames. For the upstream edge flame, flame spread rate was nearly independent of, or decreased gradually with, the imposed flow velocity. The spread rate of the downstream edge, however, increased significantly with the imposed flow velocity.

MICROGRAVITY↗

The Effect of Backward-Facing Step Height on Instability Growth and Breakdown in Swept Wing Boundary-Layer Transition

A low-speed experiment was performed on a swept at plate model with an imposed pressure gradient to determine the effect of a backward-facing step on transition in a stationary-cross flow dominated flow. Detailed hot-wire boundary-layer measurements were performed for three backward-facing step heights of approximately 36, 45, and 49% of the boundary-layer thickness at the step. These step heights correspond to a subcritical, nearly-critical, and critical case. Three leading-edge roughness configurations were tested to determine the effect of stationary-cross flow amplitude on transition. The step caused a local increase in amplitude of the stationary cross flow for the two larger step height cases, but farther downstream the amplitude decreased and remained below the baseline amplitude. The smallest step caused a slight local decrease in amplitude of the primary stationary cross flow mode, but the amplitude collapsed back to the baseline case far downstream of the step. The effect of the step on the amplitude of the primary cross flow mode increased with step height, however, the stationary cross flow amplitudes remained low and thus, stationary cross flow was not solely responsible for transition. Unsteady disturbances were present downstream of the step for all three step heights, and the amplitudes increased with increasing step height. The only exception is that the lower frequency (traveling crossflow-like) disturbance was not present in the lowest step height case. Positive and negative spikes in instantaneous velocity began to occur for the two larger step height cases and then grew in number and amplitude downstream of reattachment, eventually leading to transition. The number and amplitude of spikes varied depending on the step height and cross flow amplitude. Despite the low amplitude of the disturbances in the intermediate step height case, breakdown began to occur intermittently and the flow underwent a long transition region.

Eppink, Jenna L.↗

Stress intensities for cracks emanating from pin-loaded holes

A series of stress freezing photoelastic experiments were conducted on large plates containing central holes with cracks emanating from the edge formed by the intersection of the hole with the plate surface. Loads were applied through rigid pins with neat fits in the holes. Stress-intensity factors (SIF) were estimated by a computer assisted least squares analysis of the photoelastic data taken from slices near the points of intersection of the flaw border with the hole boundary and the plate surface. Results indicate that the local mode of loading changes from Mode 1 near the hole boundary to mixed mode near the plate surface. The analysis is extended to include mixed mode loading, and results are compared with an existing approximate theory.

Smith, C. W.↗

Hydrodynamic Stability and Magnetic Reconnection in Disks and Stars

The purpose of this grant is to study parametric instability. The simplest example of parametric instability is a harmonic oscillator with a periodic modulation of the spring constant. If the modulation frequency is close to twice the natural frequency of the oscillator, the amplitude of oscillation tends to grow exponentially. The growth rate is proportional to the strength of the modulation, but it also depends upon the closeness to resonance of the two frequencies, and upon natural damping rate or "Q" of the oscillator. Parametric instabilities are very common in physics. A familiar example is a jogger's ponytail--normally a very strongly damped pendulum, it can be destabilized by the variation in effective gravity during the jogger's stride. Observation confirms that the period of the pendulum is half that of the jogger's vertical motion. In astrophysics, parametric instability may occur by external tidal forcing, or by interaction among eigenmodes. In the latter case, an energetic eigenmode may destabilize modes of half its frequency, provided some weak nonlinearity exists to couple them. Under a previous Astrophysical Theory grant (NAGW-2419), the PI discovered a parametric instability of tidally forced disks such as the accretion disks in cataclysmic variables and X ray binaries [2]. The destabilized modes are tightly-wound, incompressible, three-dimensional waves analogous to g-modes and r-modes in stars. Later work has confirmed our analysis [4]. It was hoped that these modes might provide a source of turbulence and angular momentum transport in accretion disks. However, a follow-up investigation of this instability by local numerical simulations, although confirming the analytically estimated growth rates, found negligible angular momentum flux [3]. Other work, partly supported by the ATP, now strongly indicates that the transport mechanism in such disks is magnetohydrodynamic turbulence [6]. Nevertheless, the parametric mechanism may truncate the outer edges of disks in close binaries [2], and it may be important in disks of very low ionization such as protostellar disks, or even cataclysmic-variable disks in quiescence where the MHD mechanism may be ineffective [5]. All analyses up to 1996 were done in a local approximation where the orbital frequency, shear rate, and tidal field were treated as constants. The locally computed growth rate turns out to depend strongly on radius, and it was unclear how to average these local rates to obtain the correct global rate. This is a critical issue for accretion disks in close binaries, because the local growth rate is comparable to the orbital frequency towards the outer edge of the disk but decreases rapidly inwards. Paper #1 examined this issue in a simplified global model where the destabilizing terms vary with position. We found that the global growth rate is essentially equal to the maximum local rate, provided that the latter is smoothed over a radial range equal to the distance that the destabilized wave propagates at its group speed in one growth time. Thus, in an accretion disk, waves would grow rapidly in the outer parts but would propagate both inwards and outwards at a maximum group speed of order the disk thickness divided by the orbital period.

Goodman, Jeremy↗

Dynamic analysis of a pre-and-post ice impacted blade

The dynamic characteristics of an engine blade are evaluated under pre-and-post ice impact conditions using the NASA in-house computer code BLASIM. The ice impacts the leading edge of the blade causing severe local damage. The local structural response of the blade due to the ice impact is predicted via a transient response analysis by modeling only a local patch around the impact region. After ice impact, the global geometry of the blade is updated using deformations of the local patch and a free vibration analysis is performed. The effects of ice impact location, size and ice velocity on the blade mode shapes and natural frequencies are investigated. The results indicate that basic nature of the mode shapes remains unchanged after impact and that the maximum variation in natural frequencies occurs for the twisting mode of the blade.

Abumeri, G. H.↗

Dynamic analysis of a pre-and-post ice impacted blade

The dynamic characteristics of an engine blade are evaluated under pre-and-post ice impact conditions using the NASA in-house computer code BLASIM. The ice impacts the leading edge of the blade causing severe local damage. The local structural response of the blade due to the ice impact is predicted via a transient response analysis by modeling only a local patch around the impact region. After ice impact, the global geometry of the blade is updated using deformations of the local patch and a free vibration analysis is performed. The effects of ice impact location, ice size and ice velocity on the blade mode shapes and natural frequencies are investigated. The results indicate that basic nature of the mode shapes remains unchanged after impact and that the maximum variation in natural frequencies occurs for the twisting mode of the blade.

Abumeri, G. H.↗

Skin-Stiffener Debond Prediction Based on Computational Fracture Analysis

Interlaminar fracture mechanics has proven useful for characterizing the onset of delaminations in composites and has been used with limited success primarily to investigate onset in fracture toughness specimens and laboratory size coupon type specimens. Future acceptance of the methodology by industry and certification authorities however, requires the successful demonstration of the methodology on structural level. For this purpose a panel was selected that is reinforced with stringers. Shear loading causes the panel to buckle and the resulting out-of-plane deformations initiate skin/stringer separation at the location of an embedded defect. For finite element analysis, the panel and surrounding load fixture were modeled with shell elements. A small section of the stringer foot and the panel in the vicinity of the embedded defect were modeled with a local 3D solid model. Across the width of the stringer foot the mixed-mode strain energy release rates were calculated using the virtual crack closure technique. A failure index was calculated by correlating the results with the mixed-mode failure criterion of the graphite/epoxy material. For small applied loads the failure index is well below one across the entire width. With increasing load the failure index approaches one first near the edge of the stringer foot from which delamination is expected to grow. With increasing delamination lengths the buckling pattern of the panel changes and the failure index increases which suggests that rapid delamination growth from the initial defect is to be expected.

Krueger, Ronald↗

Beam-generated upper hybrid noise in Jupiter's outer magnetosphere

A model for generation of upper hybrid waves in Jupiter's outer magnetosphere is presented. Energetic electrons accelerated on high-latitude auroral field lines at 1 R(J) altitudes are assumed to stream outwards to the distant magnetosphere. The large decrease in the local magnetic field strength results in a highly collimated, field-aligned electron beam due to conservation of the particle's magnetic moment. As the beam travels outward it passes through the plasma sheet boundary layer region located on the edges of the plasma sheet. Because of the large field-aligned anisotropy of the beam, the distribution is unstable to the excitation of the upper hybrid waves which amplify and then undergo mode conversion at the f(p) layer to generate the Jovian continuum radiation. A novel feature of the model is the beam-anisotropic heat flux instability which drives UH waves unstable without the need for any positive slope on the electron distribution function.

Barbosa, D. D.↗

Vortex simulation of three-dimensional, spotlike disturbances in a laminar boundary layer

The growth of a turbulent spot in a laminar boundary layer, as the spot evolves from a localized disturbance in the layer, is simulated numerically using a three-dimensional vortex filament description of the vorticity field. The filaments are marked with a sequence of mode points which are tracked in a Lagrangian reference frame. Velocity computation is done by Biot-Savart integration. Although some discrepancies with experiment appear to exist in the near wall region, the gross properties of the spot, including the velocities of the leading and trailing edges and the velocity perturbations away from the wall, are in good agreement with experiment.

Leonard, A.↗

A comparison of experimental and calculated thin-shell leading-edge buckling due to thermal stresses

High-temperature thin-shell leading-edge buckling test data are analyzed using NASA structural analysis (NASTRAN) as a finite element tool for predicting thermal buckling characteristics. Buckling points are predicted for several combinations of edge boundary conditions. The problem of relating the appropriate plate area to the edge stress distribution and the stress gradient is addressed in terms of analysis assumptions. Local plasticity was found to occur on the specimen analyzed, and this tended to simplify the basic problem since it effectively equalized the stress gradient from loaded edge to loaded edge. The initial loading was found to be difficult to select for the buckling analysis because of the transient nature of thermal stress. Multiple initial model loadings are likely required for complicated thermal stress time histories before a pertinent finite element buckling analysis can be achieved. The basic mode shapes determined from experimentation were correctly identified from computation.

Jenkins, Jerald M.↗

Tests of graphite/polyimide sandwich panels in uniaxial edgewise compression

The local and general buckling behavior of graphite/polyimide sandwich panels simply supported along all four edges and loaded in uniaxial edgewise compression were investigated. Material properties of sandwich panel constituents (adhesive and facings) were determined from flatwise tension and sandwich beam flexure tests. Buckling specimens were 30.5 by 33 cm, had quasi-isotropic, symmetric facings, and a glass/polyimide honeycomb core. Core thicknesses were varied and three panels of each thickness were tested at room temperature to investigate failure modes and corresponding buckling loads. Specimens 0.635 cm thick failed by overall buckling at loads close to the analytically predicted buckling load; all other panels failed by face wrinkling. Results of the wrinkling tests indicated that several buckling formulas were unconservative and therefore not suitable for design purposes; a recommended wrinkling equation is presented.

Camarda, C. J.↗

A mechanism for magnetospheric substorms

Energy-principle analysis performed on two-dimensional, self-consistent solutions for magnetospheric convection indicates that the magnetosphere is unstable to isobaric (yet still frozen-in) fluctuations of plasma-sheet flux tubes. Normally, pdV work associated with compression maintains stability of the inward/outward oscillating normal mode. However, if Earth's ionosphere can provide sufficient mass flux, isobaric expansion of flux tubes can occur. The growth of a field-aligned potential drop in the near-Earth, midnight portion of the plasma sheet, associated with upward field-aligned currents responsible for the Harang discontinuity, redistributes plasma along field lines in a manner that destabilizes the normal mode. The growth of this unstable mode results in an out-of-equilibrium situation near the inner edge. When this occurs over a downtail extent comparable to the half-thickness of the plasma sheet, collapse ensues and forces thinning of the plasma sheet whereby conditions favorable to reconnection occur. This scenario for substorm onset is consistent with observed upward fluxes of ions, parallel potential drops, and observations of substorm onset. These observations include near Earth onset, pseudobreakups, the substorm current wedge, and local variations of plasma-sheet thickness.

Erickson, G. M.↗

Local delamination in laminates with angle ply matrix cracks. Part 2: Delamination fracture analysis and fatigue characterization

Constant amplitude tension-tension fatigue tests were conducted on AS4/3501-6 graphite/epoxy (02/ theta sub 2/ -(theta sub 2))sub s laminates, where theta was 15, 20, 25, or 30 degrees. Fatigue tests were conducted at a frequency of 5 Hz and an R-ratio of 0.1. Dye penetrant enhanced x-radiography was used to document the onset of matrix cracking in the central -(theta) degree plies, and the subsequent onset of local delaminations in the theta/ -(theta) interface at the intersection of the matrix cracks and the free edge, as a function of the number of fatigue cycles. Two strain energy release rate solutions for local delamination from matrix cracks were derived: one for a local delamination growing from an angle ply matrix crack with a uniform delamination growing from an angle ply matrix crack with a triangular shaped delamination area that extended only partially into the laminate width from the free edge. Plots of G(max) vs. N were generated to assess the accuracy of these G solutions. The influence of residual thermal and moisture stresses on G were also quantified. However, a detailed analysis of the G components and a mixed-mode fatigue failure criterion for this material may be needed to predict the fatigue behavior of these laminates.

Obrien, T. Kevin↗

Analysis of local delaminations caused by angle ply matrix cracks

Two different families of graphite/epoxy laminates with similar layups but different stacking sequences, (0,theta,-theta) sub s and (-theta/theta/0) sub s were analyzed using three-dimensional finite element analysis for theta = 15 and 30 degrees. Delaminations were modeled in the -theta/theta interface, bounded by a matrix crack and the stress free edge. The total strain energy release rate, G, along the delamination front was computed using three different techniques: the virtual crack closure technique (VCCT), the equivalent domain Integral (EDI) technique, and a global energy balance technique. The opening fracture mode component of the strain energy release rate, Gl, along the delamination front was also computed for various delamination lengths using VCCT. The effect of residual thermal and moisture stresses on G was evaluated.

Salpekar, Satish A.↗

Slow mode transition in the frontside magnetosheath

Three magnetosheath passes with density enhancements in front of the magnetopause are studied with data from ISEE 1, 2, and 3. The density structure appears to be locally generated and slow mode in nature. In one pass when ISEE 1 and 2 were well separated, the motion of the density structure can be determined. The density structure appears to stand in the magnetosheath flow. Thus, it propagates upstream in the rest frame of the flow. The flow in and near the density structure appears to be closer to isothermal than adiabatic. The flow velocity decreases from super-slow to being close to the intermediate and slow mode velocities at the outer edge of the density structure. This study provides additional evidence that the density structure in front of the magnetopause is a slow mode transition in which the flow velocity decreases to the MHD slow mode velocity. The slow mode transition may consist of two wave fronts and a region with strong slow mode waves. This slow mode transition may play an important role in establishing the flow and field pattern near the magnetopause.

Song, P.↗

Experimental determination of the effects of moisture on composite-to-composite adhesive joints

The primary mode of moisture ingress into bonded composite joints is determined using a nuclear probe for deuterium (NPD) to measure the localized D2O content along the length of the adhesive (FM-300 and EA-9601) and through the thickness of bonded composite speciments. Calculated diffusivities and NPD measured equilibrium moisture contents are used to predict the moisture profiles along the length of the adhesives as a function of exposure time, temperature, and relative humidity. These results are compared with the observed moisture profiles to evaluate the extent of enhanced edge diffusion. The FM-300 adhesive exhibits good agreement between measured and predicted profiles at 49 C, 70% and 90% RH, and 77 C, 70% RH. At 77 C, 90% RH, the measured moisture content near the adhesive edge is substantially larger than the predicted level. The EA-9601 adhesive also shows good agreement at 49 C, 70% and 90% RH, but at 77 C, the concentration of D20 near the edges is enhanced at each humidity level. The effect of moisture content on the bond shear strength at room temperature and at elevated temperature is evaluated.

Deiasi, R. J.↗

A broad-band VLF-burst associated with ring-current electrons

Frequency band broadening takes place just outside of the nighttime plasmasphere, where the density of cold plasma is known to be very low during the later phase of a geomagnetic storm. Instead of the gradual broadening of several hours duration, a burst type broadening of VLF emission lasting less than ten minutes was observed by Explorer 45 in a similar location. The magnetic field component of this emission is very weak and the frequency spreads below the local half electron cyclotron frequency. Corresponding enhancement of the anisotropic ring current electrons is also very sudden and limited below the order of 10 keV without significant velocity dispersion, in contrast to the gradual broadening events. The cause of this type of emission band spreading can be attributed to the generation of the quasielectrostatic whistler mode emission of short wavelength by hot bimaxwellian electrons surging into the domain of relatively low density magnetized cold plasma. The lack of energy dispersion in the enhanced electrons indicates that the inner edge of the plasma sheet, the source of these hot electrons, is not far from the location of this event.

Maeda, K.↗