Search NASA⌕ Search

SEARCH · Search NASA

Results for “FATIGUE DIAGRAM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Mechanical properties of ion-beam-textured surgical implant alloys

An electron-bombardment Hg ion thruster was used as an ion source to texture surfaces of materials used to make orthopedic and/or dental prostheses or implants. The materials textured include 316 stainless steel, titanium-6% aluminum, 4% vanadium, and cobalt-20% chromium, 15% tungsten. To determine the effect of ion texturing on the ultimate strength and yield strength, stainless steel and Co-Cr-W alloy samples were tensile tested to failure. Three types of samples of both materials were tested. One type was ion-textured (the process also heats each sample to 300 C), another type was simply heated to 300 C in an oven, and the third type was untreated. Stress-strain diagrams, 0.2% offset yield strength data, total elongation data, and area reduction data are presented. Fatigue specimens of ion textured and untextured 316 stainless steel and Ti-6% Al-4% V were tested. Included as an ion textured sample is a Ti-6% Al-4% V sample which was ion machined by means of Ni screen mask so as to produce an array of 140 mu m x 140 mu m x 60 mu m deep pits. Scanning electron microscopy was used to characterize the ion textured surfaces.

Weigand, A. J.↗
NASA NTRS1944

Axial Fatigue Tests at Zero Mean Stress of 24S-T Aluminum-alloy Sheet with and Without a Circular Hole

Axial fatigue tests were made on 189 coupon specimens of 0.032-inch 24S-T aluminum-alloy sheet and a few supplementary specimens of 0.004-inch sheet. The mean load was zero. The specimens were restrained against lateral buckling by lubricated solid guides described in a previous report on this project. About two-thirds of the 0.032-inch specimens were plain coupons nominally free from stress raisers. The remainder contained a 0.1285-inch drilled hole at the center where the reduced section was 0.5 inch wide. S-N diagrams were obtained for cycles to failure between about 1000 and 10 to the 7th power cycles for the plain specimens and 17 and 10 to the 7th power cycles for the drilled specimens. The fatigue stress concentration factor increased from about 1.08 for a stress amplitude causing failure at 0.25 cycles (static) to a maximum of 1.83 at 15,000 cycles and then decreased gradually. The graph for the drilled specimens showed less scatter than that for the plain specimens.

TESTING MACHINES, FATIGUE↗
NASA NTRS1971

Generation of Finite Life Distributional Goodman Diagrams for Reliability Prediction

The methodology of developing finite life distributional Goodman diagrams and surfaces is described for presenting allowable combinations of alternating stress and mean stress to the design engineer. The combined stress condition is that of an alternating bending stress and a constant shear stress. The finite life Goodman diagrams and surfaces are created from strength distributions developed at various ratios of alternating to mean stress at particular cycle life values. The conclusions indicate that the Von Mises-Hencky ellipse, for cycle life values above 1000 cycles, is an adequate model of the finite life Goodman diagram. In addition, suggestions are made which reduce the number of experimental data points required in a fatigue data acquisition program.

Kececioglu, D.↗
NASA NTRS2018

From S-N to the Paris Law with a New Mixed-Mode Cohesive Fatigue Model

The relationship between fatigue life and fatigue crack propagation rate is explored with a new cohesive damage model. The parameters of the model are obtained from idealizations of S-N diagrams used in engineering design. The model is based on the hypothesis that both stable tearing damage and damage due to cyclic loading are representations of a density of microcracks and, therefore, a single damage variable can describe the state of damage. This assumption implies that the quasi-static cohesive law that describes tearing is also the envelope of the fatigue damage. Fatigue damage within the cohesive envelope is assumed to accumulate at a rate that depends on the displacement jumps. The fatigue model was implemented as a UMAT subroutine for Abaqus cohesive elements by adding fatigue damage accumulation to a cohesive model based on the Turon mixed-mode cohesive laws. The analyses were conducted using a simplified cyclic loading procedure in which the maximum applied load is kept constant and the computational expense of cycling the load is avoided. The predicted propagation rates in mode I and mixed mode were compared to experimental results for IM7/8552 graphite/epoxy tape. Several aspects of the results were investigated, including the effect of R-curves, the stress ratio R, and the difference between displacement control and force control.

Davila, Carlos G.↗
NASA NTRS1989

Mean stress and the exhaustion of fatigue-damage resistance

Mean-stress effects on fatigue life are critical in isothermal and thermomechanically loaded materials and composites. Unfortunately, existing mean-stress life-prediction methods do not incorporate physical fatigue damage mechanisms. An objective is to examine the relation between mean-stress induced damage (as measured by acoustic emission) and existing life-prediction methods. Acoustic emission instrumentation has indicated that, as with static yielding, fatigue damage results from dislocation buildup and motion until dislocation saturation is reached, after which void formation and coalescence predominate. Correlation of damage processes with similar mechanisms under monotonic loading led to a reinterpretation of Goodman diagrams for 40 alloys and a modification of Morrow's formulation for life prediction under mean stresses. Further testing, using acoustic emission to monitor dislocation dynamics, can generate data for developing a more general model for fatigue under mean stress.

Berkovits, Avraham↗
NASA NTRS2024

Forced Response Aeromechanics Analysis in MATLAB®-Based Environment Code With Application to Distortion-Tolerant Fan R24 Blade Geometry

Researchers at the NASA Glenn Research Center have developed a research-level code for forced response analysis for turbomachinery that provides a streamlined framework for aeromechanics analysis, as well as for generating Goodman diagrams. The Forced Response Aeromechanics Analysis in a MATLAB-Based Environment (FRAAME, Version 1) code is designed to accept blade surface unsteady pressure time histories generated by three-dimensional (3D) Unsteady Reynolds-Averaged Navier-Stokes (URANS) code TURBO and modal displacements, modal stresses, and static stresses generated via expanded ANSYS® (Ansys, Inc.) cyclic symmetry analysis. The code’s looping structure allows for largescale analyses, including many blade surface pressure files, modal displacements, and modal stress files for full annulus forced response analysis, including a modal summation method for multiple engine orders and modes. This code is applied to the R24 fan geometry for the Boundary Layer Ingesting Inlet/Distortion-Tolerant Fan (BLI2DTF) project, a propulsion system being developed to increase the fuel efficiency of future aircraft, to serve as validation of experimental data as well as external simulation results. This tool’s functional, modular form is intended to allow users to make modifications easily. Those modifications can include requests for information for any step in the analysis process, as well as adding various functions to compute additional information of interest. It is also written, given sufficient input information, as a general blade geometry forced response solver that is not necessarily specific to the R24 geometry but is used here for verification of code functionality and accuracy. Although forced response analysis tools are also available in commercially available code packages, the post-processing FRAAME code offers reliable, fast, and scalable forced response analysis and Goodman diagram generation for large cases utilizing, specifically, TURBO and ANSYS® results information in an effort to streamline forced response and high cycle fatigue analyses.

Aeromechanics↗
NASA NTRSDate not supplied

TPSAS-NF1676L-32227-DND

The ability of a recently proposed cohesive fatigue model to predict the initiation and propagation of skin/stiffener separation was evaluated using a three-point bend (3PB) configuration. The 3PB specimen consists of a quasi-isotropic laminate representing the skin of a fuselage. A shorter doubler representing the flange of a stiffener is co-cured at the center of the specimen. A simplified modeling technique was applied, in which the complex damage mechanisms involved in the separation, such as delamination migration, matrix cracking, bridging, and crack delving are represented by a mixed-mode trilinear cohesive law at the interface between the skin and the doubler. The quasi-static properties of the trilinear law were characterized. The main advantage of the proposed fatigue model is that it relies on quasi-static properties as well as engineering assumptions to compose the shape of the S-N diagram. The model does not require Paris law data, and it is capable of predicting the initiation of separation, the rate of propagation, as well as the effects of crack resistance curves and the stress ratio.

Carlos G Davila↗
NASA NTRS1976

A computer program incorporating fatigue and fracture criteria in the preliminary design of transport aircraft: An evaluation

The APAS program a multistation structural synthesis procedure developed to evaluate material, geometry, and configuration with various design criteria usually considered for the primary structure of transport aircraft is described and evaluated. Recommendations to improve accuracy and extend the capabilities of the APAS program are given. Flow diagrams are included.

Berger, P. E.↗
NASA NTRS2011

Comprehensive Forced Response Analysis of J2X Turbine Bladed-Discs with 360 Degree Variation in CFD Loading

The temporal frequency content of the dynamic pressure predicted by a 360 degree computational fluid dynamics (CFD) analysis of a turbine flow field provides indicators of forcing function excitation frequencies (e.g., multiples of blade pass frequency) for turbine components. For the Pratt and Whitney Rocketdyne J-2X engine turbopumps, Campbell diagrams generated using these forcing function frequencies and the results of NASTRAN modal analyses show a number of components with modes in the engine operating range. As a consequence, forced response and static analyses are required for the prediction of combined stress, high cycle fatigue safety factors (HCFSF). Cyclically symmetric structural models have been used to analyze turbine vane and blade rows, not only in modal analyses, but also in forced response and static analyses. Due to the tortuous flow pattern in the turbine, dynamic pressure loading is not cyclically symmetric. Furthermore, CFD analyses predict dynamic pressure waves caused by adjacent and non-adjacent blade/vane rows upstream and downstream of the row analyzed. A MATLAB script has been written to calculate displacements due to the complex cyclically asymmetric dynamic pressure components predicted by CFD analysis, for all grids in a blade/vane row, at a chosen turbopump running speed. The MATLAB displacements are then read into NASTRAN, and dynamic stresses are calculated, including an adjustment for possible mistuning. In a cyclically symmetric NASTRAN static analysis, static stresses due to centrifugal, thermal, and pressure loading at the mode running speed are calculated. MATLAB is used to generate the HCFSF at each grid in the blade/vane row. When compared to an approach assuming cyclic symmetry in the dynamic flow field, the current approach provides better assurance that the worst case safety factor has been identified. An extended example for a J-2X turbopump component is provided.

Elrod, David↗
NASA NTRS1974

Fracture control methods for space vehicles. Volume 1: Fracture control design methods

A systematic approach for applying methods for fracture control in the structural components of space vehicles consists of four major steps. The first step is to define the primary load-carrying structural elements and the type of load, environment, and design stress levels acting upon them. The second step is to identify the potential fracture-critical parts by means of a selection logic flow diagram. The third step is to evaluate the safe-life and fail-safe capabilities of the specified part. The last step in the sequence is to apply the control procedures that will prevent damage to the fracture-critical parts. The fracture control methods discussed include fatigue design and analysis methods, methods for preventing crack-like defects, fracture mechanics analysis methods, and nondestructive evaluation methods. An example problem is presented for evaluation of the safe-crack-growth capability of the space shuttle crew compartment skin structure.

Liu, A. F.↗
NASA NTRS1986

Effect on interference fits on roller bearing fatigue life

An analysis was performed to determine the effects of inner-ring speed and press fits on roller bearing fatigue life. The effects of the resultant hoop and radial stresses on the principal stresses were considered. The maximum shear stresses below the Hertzian contact were determined for different conditions of inner-ring speed and load, and were applied to a conventional roller bearing life analysis. The effect of mean stress was determined using Goodman diagram approach. Hoop stresses caused by press fits and centrifugal force can reduce bearing life by as much as 90 percent. Use of a Goodman diagram predicts life reductions of 20 to 30 percent. The depth of the maximum shear stress remains virtually unchanged.

Coe, H. H.↗
NASA NTRS1987

Effect of interference fits on roller bearing fatigue life

An analysis was performed to determine the effects of inner-ring speed and press fits on roller bearing fatigue life. The effects of the resultant hoop and radial stresses on the principal stresses were considered. The maximum shear stresses below the Hertzian contact were determined for different conditions of inner-ring speed and load, and were applied to a conventional roller bearing life analysis. The effect of mean stress was determined using Goodman diagram approach. Hoop stresses caused by press fits and centrifugal force can reduce bearing life by as much as 90 percent. Use of a Goodman diagram predicts life reduction of 20 to 30 percent. The depth of the maximum shear stress remains virtually unchanged.

Coe, Harold H.↗
NASA NTRS1995

In-phase thermomechanical fatigue mechanisms in an unidirectional SCS-6/Ti 15-3 MMC

The objective of this investigation was to identify the inelastic deformation and damage mechanisms under in-phase (IP) thermomechanical fatigue (TMF) in a unidirectional SCS-6/Ti 15-3 metal matrix composite (MMC). Load-controlled IP TMF tests were conducted at 300-538 C at various stress ranges in high-purity argon. A major emphasis of this work was to identify damage mechanism well before final fracture of specimens, rather than to generate life diagrams, to aid development of a realistic deformation/damage and life model.

Newaz, Golam M.↗
NASA NTRS1971

Design features and results from fatigue reliability research machines.

The design, fabrication, development, operation, calibration and results from reversed bending combined with steady torque fatigue research machines are presented. Fifteen-centimeter long, notched, SAE 4340 steel specimens are subjected to various combinations of these stresses and cycled to failure. Failure occurs when the crack in the notch passes through the specimen automatically shutting down the test machine. These cycles-to-failure data are statistically analyzed to develop a probabilistic S-N diagram. These diagrams have many uses; a rotating component design example given in the literature shows that minimum size and weight for a specified number of cycles and reliability can be calculated using these diagrams.

Lalli, V. R.↗
NASA NTRS1974

Alternating bending-steady torque fatigue reliability

Results generated by three unique fatigue reliability research machines which can apply alternating-bending loads combined with steady torque are presented. Six-inch long, AISI steel, grooved specimens with a stress concentration factor of 1.42 and Rockwell C 35/40 hardness were subjected to various combinations of these loads and cycled to failure. The generated cycles-to-failure and staircase-testing data are statistically analyzed to develop distributional S-N and Goodman diagrams. Various failure theories are investigated to determine which one best represents the data. The effect of the groove and of the various combined bending-torsion loads on the finite and endurance life strength of such components, as well as on the Goodman diagram, are determined. Design applications are presented.

Kececioglu, D.↗
NASA NTRS1975

Combined bending-torsion fatigue reliability. III

Results generated by three, unique fatigue reliability research machines which can apply reversed bending loads combined with steady torque are presented. AISI 4340 steel, grooved specimens with a stress concentration factor of 1.42 and 2.34, and Rockwell C hardness of 35/40 were subjected to various combinations of these loads and cycled to failure. The generated cycles-to-failure and stress-to-failure data are statistically analyzed to develop distributional S-N and Goodman diagrams. Various failure theories are investigated to determine which one represents the data best. The effects of the groove, and of the various combined bending-torsion loads, on the S-N and Goodman diagrams are determined. Two design applications are presented which illustrate the direct useability and value of the distributional failure governing strength and cycles-to-failure data in designing for specified levels of reliability and in predicting the reliability of given designs.

Kececioglu, D.↗
NASA NTRS1974

Combined bending-torsion fatigue reliability of AISI 4340 steel shafting with K sub t = 2.34

Results generated by three, unique fatigue reliability research machines which can apply reversed bending loads combined with steady torque are presented. Six-inch long, AISI 4340 steel, grooved specimens with a stress concentration factor of 2.34 and R sub C 35/40 hardness were subjected to various combinations of these loads and cycled to failure. The generated cycles-to-failure and stress-to-failure data are statistically analyzed to develop distributional S-N and Goodman diagrams. Various failure theories are investigated to determine which one represents the data best. The effect of the groove and of the various combined bending-torsion loads on the S-N and Goodman diagrams are determined. Three design applications are presented. The third one illustrates the weight savings that may be achieved by designing for reliability.

Kececioglu, D.↗