Search NASA⌕ Search

SEARCH · Search NASA

Results for “FIGHTER AIRCRAFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Aerodynamic Characteristics of a Supersonic Fighter Aircraft Model at Mach 0.40 to 2.47

The aerodynamic characteristics of an advanced twin-engine fighter aircraft designed for supersonic cruise have been studied in the Langley 16-Foot Transonic Tunnel and the Lewis 10- by 10-Foot Supersonic Tunnel. The objective of this investigation was to establish an aerodynamic data base for the configuration with flow-through nacelles and representative inlets. The use of a canard for trim and the effects of fairing over the inlets were assessed. Comparisons between experimental and theoretical results were also made. The theoretical results were determined by using a potential vortex lift code for subsonic speeds and a linear aerodynamic code for supersonic speeds. This investigation was conducted at Mach numbers from 0.40 to 2.47, at angles of attack from 0 deg to about 20 deg, and at inlet capture ratios of about 0.5 to 1.4.

Capone, F. J.↗
NASA NTRS1987

Multiaxis control power from thrust vectoring for a supersonic fighter aircraft model at Mach 0.20 to 2.47

The aeropropulsive characteristics of an advanced twin-engine fighter aircraft designed for supersonic cruise have been studied in the Langley 16-Foot Tansonic Tunnel and the Lewis 10- by 10-Foot Supersonic Tunnel. The objective was to determine multiaxis control-power characteristics from thrust vectoring. A two-dimensional convergent-divergent nozzle was designed to provide yaw vector angles of 0, -10, and -20 deg combined with geometric pitch vector angles of 0 and 15 deg. Yaw thrust vectoring was provided by yaw flaps located in the nozzle sidewalls. Roll control was obtained from differential pitch vectoring. This investigation was conducted at Mach numbers from 0.20 to 2.47. Angle of attack was varied from 0 to about 19 deg, and nozzle pressure ratio was varied from about 1 (jet off) to 28, depending on Mach number. Increments in force or moment coefficient that result from pitch or yaw thrust vectoring remain essentially constant over the entire angle-of-attack range of all Mach numbers tested. There was no effect of pitch vectoring on the lateral aerodynamic forces and moments and only very small effects of yaw vectoring on the longitudinal aerodynamic forces and moments. This result indicates little cross-coupling of control forces and moments for combined pitch-yaw vectoring.

Capone, Francis J.↗
NASA NTRS1980

Wind tunnel test of a fighter aircraft wing/store flutter suppression system: An international effort

A 30% scale, half span model of a lightweight fighter aircraft with an active wing/store flutter suppression system was tested in the NASA Langley Research Center sixteen foot transonic dynamics tunnel. The test featured a store configuration that was intentionally designed to exhibit a violent flutter condition. In addition to Northrop organized control laws, three European countries also contributed control laws to stabilize this condition. After the control laws were mechanized by Northrop, they were tested at the Langley facility. The model was tested up to 170% of the open loop flutter dynamic pressure in a number of cases, with the indication that a substantially greater improvement was achievable. Some special features of the test model are discussed and the design and implementation of the control laws as well as the test monitoring techniques and results are presented.

Hwang, C.↗
NASA NTRS1993

Criteria for design of integrated flight/propulsion control systems for STOVL fighter aircraft

As part of NASA's program to develop technology for short takeoff and vertical landing (STOVL) fighter aircraft, control system designs have been developed for a conceptual STOVL aircraft. This aircraft is representative of the class of mixed-flow remote-lift concepts that was identified as the preferred design approach by the U.S./U.K. STOVL Joint Assessment and Ranking Team. The control system designs have been evaluated throughout the powered-lift flight envelope on the Vertical Motion Simulator (VMS) at Ames Research Center. Items assessed in the control system evaluation were: maximum control power used in transition and vertical flight, control system dynamic response associated with thrust transfer for attitude control, thrust margin in the presence of ground effect and hot-gas ingestion, and dynamic thrust response for the engine core. Effects of wind, turbulence, and ship airwake disturbances are incorporated in the evaluation. Results provide the basis for a reassessment of existing flying-qualities design criteria applied to STOVL aircraft.

Franklin, James A.↗
NASA NTRS1993

Design criteria for integrated flight/propulsion control systems for STOVL fighter aircraft

As part of NASA's program to develop technology for short takeoff and vertical landing (STOVL) fighter aircraft, control system designs have been developed for a conceptual STOVL aircraft. This aircraft is representative of the class of mixed-flow remote-lift concepts that was identified as the preferred design approach by the US/UK STOVL Joint Assessment and Ranking Team. The control system designs have been evaluated throughout the powered-lift flight envelope on Ames Research Center's Vertical Motion Simulator. Items assessed in the control system evaluation were: maximum control power used in transition and vertical flight, control system dynamic response associated with thrust transfer for attitude control, thrust margin in the presence of ground effect and hot gas ingestion, and dynamic thrust response for the engine core. Effects of wind, turbulence, and ship airwake disturbances are incorporated in the evaluation. Results provide the basis for a reassessment of existing flying qualities design criteria applied to STOVL aircraft.

Franklin, James A.↗
NASA NTRS1986

Geometry definition and grid generation for a complete fighter aircraft

Recent advances in computing power and numerical solution procedures have enabled computational fluid dynamicists to attempt increasingly difficult problems. In particular, efforts are focusing on computations of complex three-dimensional flow fields about realistic aerodynamic bodies. To perform such computations, a very accurate and detailed description of the surface geometry must be provided, and a three-dimensional grid must be generated in the space around the body. The geometry must be supplied in a format compatible with the grid generation requirements, and must be verified to be free of inconsistencies. A procedure for performing the geometry definition of a fighter aircraft that makes use of a commercial computer-aided design/computer-aided manufacturing system is presented. Furthermore, visual representations of the geometry are generated using a computer graphics system for verification of the body definition. Finally, the three-dimensional grids for fighter-like aircraft are generated by means of an efficient new parabolic grid generation method. This method exhibits good control of grid quality.

Edwards, Thomas A.↗
NASA NTRS1986

Geometry definition and grid generation for a complete fighter aircraft

Recent advances in computing power and numerical solution procedures have enabled computational fluid dynamicists to attempt increasingly difficult problems. In particular, efforts are focusing on computations of complex three-dimensional flow fields about realistic aerodynamic bodies. To perform such computations, a very accurate and detailed description of the surface geometry must be provided, and a three-dimensional grid must be generated in the space around the body. The geometry must be supplied in a format compatible with the grid generation requirements, and must be verified to be free of inconsistencies. This paper presents a procedure for performing the geometry definition of a fighter aircraft that makes use of a commercial computer-aided design/computer-aided manufacturing system. Furthermore, visual representations of the geometry are generated using a computer graphics system for verification of the body definition. Finally, the three-dimensional grids for fighter-like aircraft are generated by means of an efficient new parabolic grid generation method. This method exhibits good control of grid quality.

Edwards, T. A.↗
NASA NTRS1980

Effect of conventional and square stores on the longitudinal aerodynamic characteristics of a fighter aircraft model at supersonic speeds

The effects of conventional and square stores on the longitudinal aerodynamic characteristics of a fighter aircraft configuration at Mach numbers of 1.6, 1.8, and 2.0 was investigated. Five conventional store configurations and six arrangements of a square store configuration were studied. All configurations of the stores produced small, positive increments in the pitching moment throughout the angle-of-attack range, but the configuration with area ruled wing tanks also had a slight decrease on stability at the higher angles of attack. There were some small changes in lift coefficient because of the addition of the stores, causing the drag increment to vary with the lift coefficient. As a result, there were corresponding changes in the increments of the maximum lift drag ratios. The store drag coefficient based on the cross sectional area of the stores ranged from a maximum of 1.1 for the configuration with three Maverick missiles to a minimum of about .040 for the two MK-84 bombs and the arrangements with four square stores touching or two square stores in tandem. Square stores located side by side yielded about 0.50 in the aft position compared to 0.74 in the forward position.

Monta, W. J.↗
NASA NTRS1987

Vortex-fin interaction on a fighter aircraft

Water tunnel tests have been conducted to study the flow associated with fin buffet for twin-fin fighter aircraft using 1/48th scale F/A-18 models. Flow visualization made use of colored dyes to determine vortex patterns, and surface hot-film anemometry was used to study the turbulent energy and the frequencies present in the flow. Configurations tested include the full aircraft, aircraft without fins, aircraft without leading-edge-extensions, and aircraft without wings. Test Reynolds number ranged from 4300 to 12,800, with corresponding Mach numbers less than 10 to the -6th. The flow studies show that the LEX vortices burst just forward of the fins at about 25-deg angle-of-attack. Hot film anemometer signals show that fin surface turbulence increases with angle of attack, and that dominant frequencies appear in the flow when bursting occurs. The dominant frequencies correspond to a Strouhal number of about 0.7 for all speeds tested, and for all angles of attack for which vortex bursting was present.

Wentz, William H., Jr.↗
NASA NTRS1982

Control of the forebody vortex orientation by asymmetric air injection. Part A: Application to enhance departure/spin recovery of fighter aircraft. Part B: Details of the flow structure

A novel concept which was developed to provide powerful directional control effectiveness for a fighter aircraft at high angles of attack, where more traditional controls have very limited capability is discussed. The concept utilizes the energy concentrated in the strong forebody vortices (which form on slender bodies at high relative incidence) by controlling the lateral orientation of the vortices with respect to the body. The present concept seeks to utilize the inherent sensitivity of the vortex positioning and its bistable nature to an advantage allowing control of the forces which are developed. As it turns out, the direction or sense of the asymmetric vortex pair is much easier to control than to attenuate. The work which was done to develop the concept for application to an aircraft is described and is directed toward the effects of the concept on aircraft forces and moments and on the flight mechanics of the aircraft during maneuvering at high angles of attack. The objective was to utilize the side force associated with asymmetric vortices, in a controlled manner, to enhance the ability of the fighter to recover from a departure from controlled flight. The results from these water tunnel and wind tunnel experiments show that a small amount of tangential blowing along the forebody near the apex can effectively alter the forebody vortex system and generate large restoring yawing moments.

Skow, A. M.↗
NASA NTRS1987

Comparison of wind tunnel and flight test afterbody and nozzle pressures for a twin-jet fighter aircraft at transonic speeds

Afterbody and nozzle pressures measured on a 1/12-scale model and in flight on a twin-jet fighter aircraft were compared as Mach number varied from 0.6 to 1.2, Reynolds number from 17.5 million to 302.5 million, and angle of attack from 1 to 7 deg. At Mach 0.6 and 0.8, nozzle pressure coefficient distributions and nozzle axial force coefficients agreed and showed good recompression. At Mach 0.9 and 1.2, flow complexity caused a loss in recompression for both flight and wind tunnel nozzle data. The flight data exhibited less negative values of pressure coefficient and lower axial force coefficients than did the wind tunnel data. Reynolds number effects were noted only at these Mach numbers. Jet temperature and mass flux ratio did not affect the comparisons of nozzle axial flow coefficient. At subsonic speeds, the levels of pressure coefficient distributions on the upper fuselage and lower nacelle surfaces for flight were less negative than those for the model. The model boundary layer thickness at the aft rake station exceeded that for the forward rake station and increased with increasing angle of attack. The flight boundary layer thickness at the aft rake station was less than that for the forward rake station and decreased with increasing angle of attack.

Nugent, Jack↗
NASA NTRS1989

Fast half-loop maneuvers for a high alpha fighter aircraft using a singular perturbation feedback control law

Singular perturbation analysis is used to derive an outer layer feedback control law for a high alpha fighter aircraft to perform the half-loop maneuver. Pitch rate and angle of attack are treated as fast variables in the derivation. Bang-bang controls are derived to transfer the aircraft state from trim to the outer layer and from the outer layer to specified final half-loop values. The pitch rate is treated as a varibale faster than the angle of attack in the transfer of the state to and from the outer layer. A simulation of the derived control law is conducted at Mach 0.6 and 15,000 feet altitude. The half-loop was performed in 13.12 seconds. It is compared with a NASA pilot simulated half-loop maneuver which took 22.42 seconds for the same initial conditions.

Garrett, Frederick E., Jr.↗
NASA NTRS1990

Qualitative evaluation of a conformal velocity vector display for use at high angles-of-attack in fighter aircraft

A piloted simulation study was conducted to evaluate the utility of a display device designed to illustrate graphically and conformally the approximate location of a fighter aircraft's velocity vector. The display device consisted of two vertical rows of light emitting diodes (LED's) located toward the center of the cockpit instrument panel to each side of the control stick. The light strings provided a logical extension of the head up display (HUD) velocity vector symbol at flight path angles which exceeded the HUD field-of-view. Four test subjects flew a modified F/A-18 model with this display in an air-to-air engagement task against an equally capable opponent. Their responses to a questionnaire indicated that the conformal velocity vector information could not be used during the scenarios investigated due to the inability to visually track a target and view the lights simultaneously.

Jones, Denise R.↗
NASA NTRS1976

Recent research related to prediction of stall/spin characteristics of fighter aircraft

The NASA Langley Research Center is currently engaged in a stall/spin research program to provide the fundamental information and design guidelines required to predict the stall/spin characteristics of fighter aircraft. The prediction methods under study include theoretical spin prediction techniques and piloted simulation studies. The paper discusses the overall status of theoretical techniques including: (1) input data requirements, (2) math model requirements, and (3) correlation between theoretical and experimental results. The Langley Differential Maneuvering Simulator (DMS) facility has been used to evaluate the spin susceptibility of several current fighters during typical air combat maneuvers and to develop and evaluate the effectiveness of automatic departure/spin prevention concepts. The evaluation procedure is described and some of the more significant results of the studies are presented.

Nguyen, L. T.↗
NASA NTRS1981

Top-mounted inlet system feasibility for transonic-supersonic fighter aircraft

The more salient findings are presented of recent top inlet performance evaluations aimed at assessing the feasibility of top-mounted inlet systems for transonic-supersonic fighter aircraft applications. Top inlet flow field and engine-inlet performance test data show the influence of key aircraft configuration variables-inlet longitudinal position, wing leading-edge extension planform area, canopy-dorsal integration, and variable incidence canards-on top inlet performance over the Mach range of 0.6 to 2.0. Top inlet performance data are compared with those or more conventional inlet/airframe integrations in an effort to assess the viability of top-mounted inlet systems relative to conventional inlet installations.

Williams, T. L.↗
NASA NTRS1990

Development of composite wing carrythrough bulkheads for fighter aircraft

Potential weight savings due to the use of composite materials for highly loaded primary structures are being demonstrated through the design, fabrication, and test of an all composite wing carrythrough bulkhead for the F/A-18 fighter aircraft. A one piece composite design which results in a 24 percent weight savings, relative to the existing aluminum bulkhead, was developed. Critical details of this design were evaluated through element tests, and a full scale prototype component was fabricated. The structural integrity of this design will be demonstrated in a comprehensive full scale test program.

Goering, J. C.↗
NASA NTRS1989

Effects of nonlinear aerodynamics and static aeroelasticity on mission performance calculations for a fighter aircraft

During conceptual design studies of advanced aircraft, the usual practice is to use linear theory to calculate the aerodynamic characteristics of candidate rigid (nonflexible) geometric external shapes. Recent developments and improvements in computational methods, especially computational fluid dynamics (CFD), provide significantly improved capability to generate detailed analysis data for the use of all disciplines involved in the evaluation of a proposed aircraft design. A multidisciplinary application of such analysis methods to calculate the effects of nonlinear aerodynamics and static aeroelasticity on the mission performance of a fighter aircraft concept is described. The aircraft configuration selected for study was defined in a previous study using linear aerodynamics and rigid geometry. The results from the previous study are used as a basis of comparison for the data generated herein. Aerodynamic characteristics are calculated using two different nonlinear theories, potential flow and rotational (Euler) flow. The aerodynamic calculations are performed in an iterative procedure with an equivalent plate structural analysis method to obtain lift and drag data for a flexible (nonrigid) aircraft. These static aeroelastic data are then used in calculating the combat and mission performance characteristics of the aircraft.

Giles, Gary L.↗
NASA NTRS2005

Application of Piloted Simulation to High-Angle-of-Attack Flight-Dynamics Research for Fighter Aircraft

This paper reviews the use of piloted simulation at Langley Research Center as part of the NASA High-Angle-of-Attack Technology Program (HATP), which was created to provide concepts and methods for the design of advanced fighter aircraft. A major research activity within this program is the development of the design processes required to take advantage of the benefits of advanced control concepts for high-angle-of-attack agility. Fundamental methodologies associated with the effective use of piloted simulation for this research are described, particularly those relating to the test techniques, validation of the test results, and design guideline/criteria development.

Ogburn, Marilyn E.↗