SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Analog and digital circuits combined to frequency-convert from intermediate frequencies directly to video-band frequencies to meet stringent requirements. IF-to-video-band converter operates on principle of signal-band cancellation in phase-quadrature circuits. Downconverts intermediate frequencies directly to video-band frequencies to near-zero frequency with good image-band rejection and low phase variation within passband.
The frequency to voltage converter analog front end evaluation prototype (F2V AFE) is an evaluation board designed for comparison of different methods of accurately extracting the frequency of a sinusoidal input signal. A configurable input stage is routed to one or several of five separate, configurable filtering circuits, and then to a configurable output stage. Amplifier selection and gain, filter corner frequencies, and comparator hysteresis and voltage reference are all easily configurable through the use of jumpers and potentiometers.
Wave Energy Converters (WECs) rely on effective Power Take-Off (PTO) control strategies to maximize energy absorption under dynamic sea conditions. Traditional hydrodynamic modeling techniques may require computationally intensive convolution calculations, making real-time control implementation challenging. This paper presents an alternative approach by leveraging instantaneous frequency estimation to dynamically adjust PTO damping in response to varying wave frequencies. Two real-time frequency estimation methods are explored: the Hilbert Transform (HT) and Phase-Locked Loop (PLL). The Hilbert Transform method provides accurate frequency tracking but introduces a delayed response due to its dependence on causal data. Conversely, the PLL approach demonstrates strong potential in frequency tracking but requires careful gain tuning, particularly in complex sea states. Comparative evaluations across multiple test cases—including sinusoidal variations, amplitude steps, frequency step changes, and real-world JONSWAP spectrum waves—highlight the strengths and limitations of each method. The two different PTO control techniques across the various frequency estimation methods were tested under real-sea states using a state-space model of a point-absorbing Wave Energy Converter. The Capture Width Ratio (CWR) is used as a performance metric, with results showing that the HT achieves a 10.6% improvement, while the PLL estimation yields a 0.9% improvement relative to the fixed parameter control baseline. These results highlight the effectiveness of real-time frequency estimation in improving energy absorption compared to static control parameters.
Preliminary results of an investigation of magnetic fluctuations seen upstream of two interplanetary shocks are presented. The spectral analysis includes calculation of the normalized reduced magnetic helicity spectrum, the normalized reduced cross-helicity spectrum, and the Alfven ratio as discussed by Matthaeus and Goldstein (1982). Minimum variance methods are used to compute wave polarization as a function of frequency. The Taylor 'frozen in flow' hypothesis is assumed to convert frequencies to wave vectors. Some of the basic properties of the waves, including the probable mode of propagation in association with both quasi-parallel forward and reverse shocks, are described. A comparison with previous results on the generation of waves at interplanetary and planetary shocks is presented.
This paper reports the results of low dose rate (0.01-0.18 rads(Si)/sec) total ionizing dose (TID) tests performed on several types of high performance converters. The parts used in this evaluation represented devices such as a high speed flash converter, a 16-bit ADC and a voltage-to-frequency converter.
Development of frequency-to-voltage converter for spacecraft instrumentation systems
A type U bursts was observed on 22 June 1998 with the WAVES radio receivers on the Wind spacecraft. It descended in frequency from 5 MHz to the turning frequency of about 1 MHz. It is extremely rare that a U burst is observed at such a low frequency, well out in the solar wind. Using a density model to convert frequency to radial distance, we find that the radio emission started at 3 solar radius, and that the electron stream turned back toward the sun at about 8 solar radius. The probable origin of the energetic electrons was in a B 6.8 X-ray flare that was coincident with the onset of the U burst. A series of images by the SOHO/LASCO chronograph show a slow (214 km/s) CME in progress on the west limb whose front was at 9 solar radius, at the time of the U burst. As no stable magnetic loops exist at radial distances such as 8-9 solar radius, we attribute the U burst to a stream of energetic electrons accelerated in an active region at the footpoint of one leg of the expanding arch of the CME. The electron stream became unstable and began emitting radio emission at about 3 solar radius, continued to emit as it passed the top of the loop at 8-9 solar radius, then stopped emitting in the downgoing leg at about 4 solar radius.
Precise laser remote sensing of aerosol extinction and backscatter in the atmosphere requires a high-power, pulsed, frequency doubled Nd:YAG laser that is wavelength- stabilized to a narrow absorption line such as found in iodine vapor. One method for precise wavelength control is to injection seed the Nd:YAG laser with a low-power CW laser that is stabilized by frequency converting a fraction of the beam to 532 nm, and to actively frequency-lock it to an iodine vapor absorption line. While the feasibility of this approach has been demonstrated using bulk optics in NASA Langley s Airborne High Spectral Resolution Lidar (HSRL) program, an ideal, lower cost solution is to develop an all-waveguide, frequency-locked seed laser in a compact, robust package that will withstand the temperature, shock, and vibration levels associated with airborne and space-based remote sensing platforms. A key technology leading to this miniaturization is the integration of an efficient waveguide frequency doubling element, and a low-voltage phase modulation element into a single, monolithic, planar light-wave circuit (PLC). The PLC concept advances NASA's future lidar systems due to its compact, efficient and reliable design, thus enabling use on small aircraft and satellites. The immediate application for this technology is targeted for NASA Langley's HSRL system for aerosol and cloud characterization. This Phase I effort proposes the development of a potassium titanyl phosphate (KTP) waveguide phase modulator for future integration into a PLC. For this innovation, the proposed device is the integration of a waveguide-based frequency doubler and phase modulator in a single, fiber pigtail device that will be capable of efficient second harmonic generation of 1,064-nm light and subsequent phase modulation of the 532 nm light at 250 MHz, providing a properly spectrally formatted beam for HSRL s seed laser locking system. Fabrication of the integrated PLC chip for NASA Langley, planned for the Phase II effort, will require full integration and optimization of the waveguide components (SHG waveguide, splitters, and phase modulator) onto a single, monolithic device. The PLC will greatly reduce the size and weight, improve electrical- to-optical efficiency, and significantly reduce the cost of NASA Langley s current stabilized HSRL seed laser system built around a commercial off-the-shelf seed laser that is free-space coupled to a bulk doubler and bulk phase modulator.
Circuit allows direct frequency to amplitude conversion without special counters and discriminators and provides for individual or simultaneous emphasis of high or low frequencies. Circuit is simple, small, light weight, and versatile in its frequency range and region of conversion.
Laboratory measurements were performed to compare the thermal coefficients of two microwave detectors that might be used for direct detection in L-band radiometers. In particular it was desired to compare the performance of a new-technology flash ADC (analog-to-digital converter) against that of an older-technology diode detector in series with a VFC (voltage-to-frequency converter). The outputs of two state-of-the-art detectors were recorded as a constant 1.414-GHz signal was input and the physical temperatures of the detectors were varied over a range of 10 C. As a further experiment, each detector was tested with a noise diode source and with a sine wave synthesizer source. Thermal coefficients were computed in terms of W/C and in terms of ppt/C at nominal operating temperatures reasonable for the individual devices. Finally, thermal coefficients were calculated in K/C to indicate the change in brightness temperature seen by a theoretical sea surface salinity radiometer employing each detector. The K/C for the flash ADC was determined to be about 2.8 times that of the diode/VFC. Different reactions of the ADC to a noise input and a sine wave input indicated that ADC tests for radiometric purposes, such as this one, should be performed using a noise input.
The system consists of several identical channels of 1024 MHz bandwidth each. In each channel, the RF band is frequency-translated to the intermediate frequency range 1 - 2 GHz. Each channel consists of two parts: the digitizer and Mark 5C recorder. The digitizer is placed on the antenna close to the corresponding Low-Noise Amplifier output and consists of the analog frequency converter, ADC, and a device for digital processing of the signals using FPGA. In the digitizer the subdigitization on frequency of 2048 MHz is used. For producing narrow-band channels and to interface with existing data acquisition systems, the polyphase filtering with FPGA can be used. Digital signals are re-quantized to 2-bits in the FPGA and are transferred to an input of Mark 5C through a fiber line. The breadboard model of the digitizer is being tested, and the data acquisition system is being designed.
Series inductance is a critical energy storage element in isolated power converters. Many have explored methods of estimating the total leakage inductance of transformers as an integrated series inductance without external inductors. However, this poses challenges with medium frequency converters and magnetic ribbon-based cores, e.g., metal amorphous nanocrystalline. The material’s relatively high conductivity allows eddy currents to develop when magnetic flux intersects wide surfaces. These eddy currents result in significant additional losses that increase with increasing power flow. This paper presents a simplified and accurate method of estimating leakage flux while identifying separate leakage flux paths that correlate with the magnetic material surfaces. This enables an understanding the proportion of leakage flux that will contribute to extra losses. The methods presented are applicable to both leakage and fringing (around heterogeneous material interfaces) fluxes. This paper includes detailed FEA studies and 3D flux vector measurements matching the presented analytical models.
Calculated and experimental design and operating characteristics of a 108-120 GHz superheterodyne radiometer with intermediate frequency modulation and a second harmonic frequency converter are presented and discussed. With a 1 sec time constant, the radiometer fluctuation sensitivity threshold is 1 K, without degradation in 2 hours of operation. Graphs of frequency variations, calibration, conversion loss, rectified current, fixed bias voltage, and contact needle impedance are included.
It is shown that two Schwarz converters in cascade provide a very reliable 20-kHz source that features zero current commutation, constant frequency, and fault-tolerant operation, meeting requirements for spacecraft applications. A steady-state analysis of the converter is presented, and equations for the steady-state performance are derived. Fault-current limiting is discussed. Experimental results are presented for a 900-W version, which has been successfully tested under no-load, full-load, and short-circut conditions.
Magnetism in two-dimensional (2D) van der Waals (vdW) crystals offers promising new directions for low-dimensional physics and devices. In this work, mega-electron volt (MeV) ultrafast electron diffraction was employed to investigate the ultrafast atomic dynamics of a novel, 2D vdW magnetic single-crystal CrSBr. Femtosecond (fs) optical pump pulses excited non-equilibrium atomic displacements shown to be coherent acoustic phonons (CAPs). Phonon frequencies were extracted by analyzing oscillations of different Bragg peak (BP) intensities and were determined to be GHz acoustic disturbances that propagated as strain waves. Phonon modes exhibit anisotropy with respect to the a and b crystal axes. Subharmonic phonon frequencies were also observed, and this provided a signature of nonlinear oscillatory coupling between the laser-induced pumping phonon frequency and secondary phonon frequencies. Thus, CrSBr was found to serve as a nonlinear phononic frequency converter. The ultrafast time dependence of the Bragg intensity was simulated by incorporating an oscillating deviation parameter ansatz into expressions for the dynamical scattering intensity yielded excellent modeling of the ultrafast structural dynamics of the photo-excited 2D crystal. Our work provides a foundation for exploring how fs light pulses can influence phonon dynamics in materials with strong spin-lattice coupling. These results suggest that CAPs can match the magnon frequencies and show the promise of CrSBr for use in optical-to-microwave transducers and phononic devices.
Filtering is commonly used in quantum optics to reject noise photons, and also to enable interference between independent photons. However, filtering the joint spectrum of photon pairs can reduce the inherent coincidence probability or loss-independent heralding efficiency. Here we investigate filtering for multiphoton applications based on entanglement and interference (e.g., quantum teleportation). We multiplex C-band entangled photons and C-band classical communications into the same long-distance fibers, which enables scalable low-loss quantum networking but requires filtering of spontaneous Raman scattering noise from classical light. Using tunable-bandwidth filters, low-jitter detectors, and polarization filters, we distribute wavelength-degenerate time-bin entangled photons in the C band (1536.5 nm) over 25 km/25 km standard fibers (50 km) each carrying 10 Gbit/s C-band classical data signals. Narrow filtering enables milliwatt-level C-band power, which exceeds the power achieved by comparable studies by roughly an order of magnitude and could feasibly support terabit per second classical rates. We evaluate how performance depends on pump and filter bandwidths, multipair emission, filter shapes, loss, phase matching, and how quantum information is measured. We find a trade-off between reducing noise impact and increasing single-mode purity, and discuss mitigation methods toward optimal multiphoton applications. Importantly, these results apply to noise in free space and in quantum devices (sources, frequency converters, switches, detectors, etc.) and provide insight into filter-induced degradation of single-photon purity and rates even in noise-free environments.
The report summarizes the development of a high rate, high fidelity, bichromatic entangled photon pair source that serves as a frequency converter between Rubidium based atomic vapor quantum devices (memories, sensors, computers) and telecom fiber.
Circuit with a sawtooth-modulated traveling-wave tube, which acts as a frequency converter and as an amplifier, simplifies microwave transmission. Lower power losses and reduced size and weight are also realized in this circuit.