Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUEL VALVE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1922

The Effect of Longitudinal Moment of Inertia upon Dynamic Stability

Free flight tests were carried out to show whether the longitudinal oscillations of a standard S.E.5A airplane are noticeably affected if its longitudinal moment of inertia is increased. These oscillations were taken by means of a self-recording instrument, the airplane having first its ordinary moment of inertia and then one increased by 14 percent. The period of oscillation was slightly longer after the increase of the moment of inertia, but the damping was not affected. Presented here are test results from an investigation to determine the relative performance of a single-cylinder, high-speed, compression-ignition engine when using fuel injection valve nozzles with different numbers, sizes, and directions of round orifices. A spring loaded, automatic injection valve was used. It was centrally located at the top of a vertical disk-type combustion chamber formed between horizontally opposed inlet and exhaust valves of a 5-inch by 7-inch engine. A series of fuel injection valve nozzles with different arrangements of round orifices were tested, starting with orifices so small that impingement on the combustion chamber walls was impossible and increasing beyond the start of impingement. a :A table and curves are presented showing the performance of the engine with different nozzles. The test results are discussed, and some probable reasons given for the variation in performance with different nozzles on the basis of spray distribution.

MOMENTS OF INERTIA - ROYAL AIRCRAFT FACTORY S E 5A↗
NASA NTRS1978

Fabrication and test of digital output interface devices for gas turbine electronic controls

A program was conducted to develop an innovative digital output interface device, a digital effector with optical feedback of the fuel metering valve position, for future electronic controls for gas turbine engines. A digital effector (on-off solenoids driven directly by on-off signals from a digital electronic controller) with optical position feedback was fabricated, coupled with the fuel metering valve, and tested under simulated engine operating conditions. The testing indicated that a digital effector with optical position feedback is a suitable candidate, with proper development for future digital electronic gas turbine controls. The testing also identified several problem areas which would have to be overcome in a final production configuration.

Newirth, D. M.↗
NASA NTRS2005

High-Temperature Piezoelectric Ceramic Developed

Active combustion control of spatial and temporal variations in the local fuel-to-air ratio is of considerable interest for suppressing combustion instabilities in lean gas turbine combustors and, thereby, achieving lower NOx levels. The actuator for fuel modulation in gas turbine combustors must meet several requirements: (1) bandwidth capability of 1000 Hz, (2) operating temperature compatible with the fuel temperature, which is in the vicinity of 400 F, (3) stroke of approximately 4 mils (100 m), and (4) force of 300 lb-force. Piezoelectric actuators offer the fastest response time (microsecond time constants) and can generate forces in excess of 2000 lb-force. The state-of-the-art piezoceramic material in industry today is Pb(Zr,Ti)O3, called PZT. This class of piezoelectric ceramic is currently used in diesel fuel injectors and in the development of high-response fuel modulation valves. PZT materials are generally limited to operating temperatures of 250 F, which is 150 F lower than the desired operating temperature for gas turbine combustor fuel-modulation injection valves. Thus, there is a clear need to increase the operating temperature range of piezoceramic devices for active combustion control in gas turbine engines.

Sayir, Ali↗
NASA NTRS1965

Postflight Evaluation of Atlas-Centaur AC-5 (Launched 2 March 1965)

The Atlas-Centaur AC-5 vehicle was launched from ETR Complex 36A on March 2., 1965 at 8:25.04 a.m. EST. Within about 1 second after launch the thrust of the Atlas booster engine decayed rapidly; the vehicle settled back on the launch pad and was quickly destroyed by fire and explosion. Considerable damage was sustained by the launch complex and its associated equipment. Loss of booster engine thrust was due to fuel depletion at the turbopump inlets, which is attributed to closure of the fuel prevalve or the staging valve. To preclude the recurrence of either of these fuel valving malfunctions, the following corrective action has been taken: The remote control actuator has been replaced by manual operation of the Atlas fuel prevalve; the internal passage dimensions in the staging valve have been increased to lessen the hydraulic load on the valve poppet. In addition to the Atlas fuel system malfunction, a failure in the power control circuitry of the Centaur guidance computer resulted in partial removal of power at umbilical ejection. To prevent such a guidance system failure on future flights some redundant circuitry has been eliminated and more rigorous checkout procedures have been adopted. No further anomalies were discovered in the telemetered data prior to the Atlas booster thrust decay. A prime objective of the AC-5 flight was to place a dynamic model of the Surveyor spacecraft in a simulated lunar transfer trajectory. An important facet of this problem is the demonstration of a launch-on-time capability in accordance with the proper Earth-moon relation. The window opening time was established at 8:25 a.m. EST; thus the actual launch occurred within 4 seconds of the planned time.

Source record↗
NASA NTRS1946

Improving the performance of a compression ignition engine by directing flow of inlet air

The object of this report is to present the results of tests performed by the National Advisory Committee for Aeronautics to determine the effect on engine performance of directing the flow of the inlet air to a 5-inch by 7-inch cylinder, solid injection, compression ignition engine, After a few preliminary tests, comparative runs were made at a speed of 1500 r.p.m. with and without directed air flow. It was found that directing the flow of the inlet air toward the fuel injection valve gave steadier engine operation, and an appreciable increase in power, and decreased fuel consumption. The results indicate the possibility of improving the performance of a given type of combustion chamber without changing its shape and with no change in valve timing. They would also seem to prove that directional turbulence, set up before the inlet valve of a four-stroke cycle engine, continues in the engine cylinder throughout the compression stroke.

Kemper, Carlton↗
NASA NTRS1925

Atomization of liquid fuels. Part II

This report describes the design and operation of a nozzle to inject fuel into an engine. The design of the nozzle is open, without any compulsory or automatic stop-valve. The fuel injection is regulated simply by the pressure and the adjustment of the fuel pump.

FUELS - TESTS↗
NASA NTRS1929

Some Effects of Air Flow on the Penetration and Distribution of Oil Sprays

Tests were made to determine the effects of air flow on the characteristics of fuel sprays from fuel injection valves. Curves and photographs are presented showing the airflow throughout the chamber and the effects of the air flow on the fuel spray characteristics. It was found that the moving air had little effect on the spray penetration except with the 0.006 inch orifice. The moving air did, however, affect the oil particles on the outside of the spray cone. After spray cut-off, the air flow rapidly distributed the atomized fuel throughout the spray chamber.

Rothrock, A M↗
NASA NTRS2000

Manufacturing and NDE of Large Composite Aerospace Structures at MSFC

NASA's vision for transportation to orbit calls for new vehicles built with new materials technology. The goals of this new launch system development are to improve safety, dramatically reduce cost to orbit, and improve vehicle turn around time. Planned Space Shuttle upgrades include new reusable liquid propellant boosters to replace the solid propellant boosters. These boosters are to have wings and return to the launch site for a horizontal landing on an airport runway. New single and two stages to orbit concepts are being investigated. To reduce weight and improve performance composite materials are proposed for fuel and oxidizer tanks, fuel feedlines, valve bodies, aerostructures, turbomachinery components. For large composite structures new methods of fabrication are being proposed and developed. Containment of cryogenic fuel or oxidizer requires emphases on composite material densification and chemical compatibility. Ceramic matrix and fiber composites for hot rotating turbomachinery have been developed with new fabrication processes. The new requirements on the materials for launcher components are requiring development of new manufacturing and inspection methods. This talk will examine new and proposed manufacturing methods to fabricate the revolutionary components. New NDE methods under consideration include alternative X-ray methods, X-ray laminagraphy, advanced CT, Thermography, new ultrasonic methods, and imbedded sensors. The sizes, complexity, use environment, and contamination restrictions will challenge the inspection process. In flight self-diagnosis and rapid depot inspection are also goals of the NDE development.

Whitaker, Ann↗
NASA NTRS1931

Performance of a Compression-ignition Engine with a Precombustion Chamber Having High-Velocity Air Flow

Presented here are the results of performance tests made with a single-cylinder, four stroke cycle, compression-ignition engine. These tests were made on a precombustion chamber type of cylinder head designed to have air velocity and tangential air flow in both the chamber and cylinder. The performance was investigated for variable load and engine speed, type of fuel spray, valve opening pressure, injection period and, for the spherical chamber, position of the injection spray relative to the air flow. The pressure variations between the pear-shaped precombustion chamber and the cylinder for motoring and full load conditions were determined with a Farnboro electric indicator. The combustion chamber designs tested gave good mixing of a single compact fuel spray with the air, but did not control the ensuing combustion sufficiently. Relative to each other, the velocity of air flow was too high, the spray dispersion by injection too great, and the metering effect of the cylinder head passage insufficient. The correct relation of these factors is of the utmost importance for engine performance.

Spanogle, J A↗
NASA NTRS1980

Fuel/hydraulic transfer valve improves reliability of Atlas space launch vehicle

The Atlas fuel hydraulic transfer valve design is described. The design satisfies primary goals such as fuel and oil isolation before launch in order to use existing ground support and airborne hardware and procedures. The valve operates only after the vehicle has been committed to launch. Hydraulic system function is maintained if the valve fails to function. Valve operation is mechanical and interfaces only with the propulsion system.

Ogman, M.↗
NASA NTRS2008

Operability of an Ejector Enhanced Pulse Combustor in a Gas Turbine Environment

A pressure-gain combustor comprised of a mechanically valved, liquid fueled pulsejet, an ejector, and an enclosing shroud, was coupled to a small automotive turbocharger to form a self-aspirating, thrust producing gas turbine engine. The system was constructed in order to investigate issues associated with the interaction of pulsed combustion devices and turbomachinery. Installed instrumentation allowed for sensing of distributed low frequency pressure and temperature, high frequency pressure in the shroud, fuel flow rate, rotational speed, thrust, and laboratory noise. The engine ran successfully and reliably, achieving a sustained thrust of 5 to 6 lbf, and maintaining a rotor speed of approximately 90,000 rpm, with a combustor pressure gain of approximately 4 percent. Numerical simulations of the system without pressure-gain combustion indicated that the turbocharger would not operate. Thus, the new combustor represented a substantial improvement in system performance. Acoustic measurements in the shroud and laboratory indicated turbine stage sound pressure level attenuation of 20 dB. This is consistent with published results from detonative combustion experiments. As expected, the mechanical reed valves suffered considerable damage under the higher pressure and thermal loading characteristics of this system. This result underscores the need for development of more robust valve systems for this application. The efficiency of the turbomachinery components did not appear to be significantly affected by unsteadiness associated with pulsed combustion, though the steady component efficiencies were already low, and thus not expected to be particularly sensitive.

Paxson, Daniel E.↗
NASA NTRS1972

Space Shuttle bipropellant RCS engine.

The requirements of the Space Shuttle bipropellant reaction control system engine technology contract and the scheduled contract effort are presented herein. The requirements included an engine concept scalable from 400 to 1100 lbf, with a 100 mission life employing N2O4/MMH propellants. Emphasis is placed on reusability and minimum post-flight servicing. The engine components are reviewed and their selection is supported by tradeoff analyses, thrust chamber firing test data, materials test data, and metallurgical evaluations. The materials test data indicate that the proposed silicide coated columbium chamber and uncoated columbium injector have the potential of meeting the mission life requirements. The engine valve trade studies resulted in the selection of a torque motor operated bipropellant valve configuration. Fuel vortex film cooling of the insulated chamber is described together with the fuel vortex film cooling scaling parameter and its verification by test data to a thrust level of 5500 lbf.

Sanscrainte, W.↗
NASA NTRS1975

SSME-HAS dynamic load simulators

The space shuttle main engine propellant valve actuators (SSME) were designed to simulate the loads reflected into the SSME by the chamber coolant valve, the fuel preburner, and the oxidizer. The design, and functional description are included along with a list of the drawings. The load fixture control transform, friction torque, and flow calculations are reported.

Source record↗