Search NASA⌕ Search

SEARCH · Search NASA

Results for “Failure Modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Comparison of Failure Modes in 2-D and 3-D Woven Carbon Phenolic Systems

NASA Ames Research Center is developing Woven Thermal Protection System (WTPS) materials as a new class of heatshields for entry vehicles (Stackpoole). Currently, there are few options for ablative entry heatshield materials, none of which is ideally suited to the planetary probe missions currently of interest to NASA. While carbon phenolic was successfully used for the missions Pioneer Venus and Galileo (to Jupiter), the heritage constituents are no longer available. An alternate carbon phenolic would need to be qualified for probe missions, which is most efficient at heat fluxes greater than those currently of interest. Additional TPS materials such as Avcoat and PICA are not sufficiently robust for the heat fluxes required. As a result, there is a large TPS gap between the materials efficient at very high conditions (carbon phenolic) and those that are effective at low-moderate conditions (all others). Development of 3D Woven TPS is intended to fill this gap, targeting mid-density weaves that could with withstand mid-range heat fluxes between 1100 W/sq cm and 8000 W/sq cm (Venkatapathy (2012). Preliminary experimental studies have been performed to show the feasibility of WTPS as a future mid-range TPS material. One study performed in the mARC Jet Facility at NASA Ames Research Center characterized the performance of a 3D Woven TPS sample and compared it to 2D carbon phenolic samples at ply angles of 0deg, 23.5deg, and 90deg. Each sample contained similar compositions of phenolic and carbon fiber volume fractions for experimental consistency. The goal of this study was to compare the performance of the TPS materials by evaluating resulting recession and failure modes. After exposing both samples to similar heat flux and pressure conditions, the 2D carbon phenolic laminate was shown to experience significant delamination between layers and further pocketing underneath separated layers. The 3D Woven TPS sample did not experience the delamination or pocketing failure modes because z-fibers in the through-thickness direction provided extra reinforcement to hold material layers together. Therefore, the benefit of using a 3D weave architecture was shown to alleviate failure modes experienced by a 2D laminate sample of similar material composition. In summary this poster reviews the thermal response performance comparisons drawn between a 3D Woven TPS sample and 2D Carbon Phenolic samples after performing rigorous heating experiments in the mARC facility at NASA Ames. Although the mARC Facility is still in its developmental stages, researchers expect similar trends in failure modes observed from large scale arc jet facilities. This work helps demonstrate the viability of 3D Woven TPSs as a new TPS option for future atmospheric entry missions.

Rossman, Grant A.↗
NASA NTRS2024

Effects of Oxide Dispersion on Failure Modes in an Additively Manufactured Superalloy

Additive manufacturing opens new paths for introducing oxide particles into superalloys, to potentially provide oxide dispersion strengthening (ODS) at high temperatures. This provides opportunities to study how such dispersions can influence failure modes for a given superalloy, after nearly identical material processing paths. The objective of this study was to compare monotonic failure modes for additively manufactured superalloys with versus without an introduced oxide dispersion. The superalloy for each case was produced by laser powder bed fusion additive manufacturing. Specimens were subsequently given consistent thermal treatment paths and then tested in tensile and creep tests at varied temperatures. Failure modes were then compared. Additively manufactured NiCrAl without ODS had randomly oriented equiaxed grains while this alloy with 0.25 wt% Y 2 O 3 ODS additions had elongated [001] oriented grains in the build direction. Material made without ODS (“No-ODS”) was nearly completely single phase gamma, while ODS additions resulted in gamma, chromium carbide, and Y-Al-Cr oxide phases, with carbide and oxide phases contents estimated at no more than 13 and 1 vol%, respectively. Compared to No-ODS, material made with ODS had higher tensile strengths at room, 760 and 1093 °C. The elongation of ODS material was lower than No-ODS at room temperature, but higher at 760 °C. At 1093 °C ODS material had higher elongation than No-ODS when tested in the build direction, however elongation was lower for ODS material in the transverse direction at 1093 °C. Creep rupture strain, life, and area reduction at 760 and 1093 °C were all much higher for ODS material compared to No-ODS; 760 °C rupture life was nearly 100 times longer for ODS material. The presence of Y in the ODS material significantly improved oxidation resistance.

supperalloys↗
NASA NTRS2012

Failure Mode Analysis of V-Shaped Pyrotechnically Actuated Valves

Current V-shaped stainless steel pyrovalve initiators have rectified many of the deficiencies of the heritage Y-shaped aluminum design. However, a credible failure mode still exists for dual simultaneous initiator (NSI) firings in which low temperatures were detected at the booster cap and less consistent ignition was observed than when a single initiator was fired. In order to asses this issue, a numerical framework has been developed for predicting the flow through pyrotechnically actuated valves. This framework includes a fully coupled solution of the gas-phase equation with a non-equilibrium dispersed phase for solid particles as well as the capability to model conjugate gradient heat transfer to the booster cap. Through a hierarchy of increasingly complex simulations, a hypothesis for the failure mode of the nearly simultaneous dual NSI firings has been proven. The simulations indicate that the failure mode for simultaneous dual NSI firings may be caused by flow interactions between the flame channels. The shock waves from each initiator interact in the booster cavity resulting in a high pressure that prevents the gas and particulate velocity from rising in the booster cap region. This impedes the bulk of the particulate phase from impacting the booster cap and reduces the heat transfer to the booster cap since the particles do not impact it. Heat transfer calculations to the solid metal indicate that gas-phase convective heat transfer may not be adequate by itself and that energy transfer from the particulate phase may be crucial for the booster cap burn through.

Sachdev, Jai S.↗
NASA NTRS1994

Matrix Failure Modes and Effects Analysis as a Knowledge Base for a Real Time Automated Diagnosis Expert System

Failure Modes and Effects Analysis contain a wealth of information that can be used to create the knowledge base required for building automated diagnostic Expert systems. A real time monitoring and diagnosis expert system based on an actual NASA project's matrix failure modes and effects analysis was developed. This Expert system Was developed at NASA Ames Research Center. This system was first used as a case study to monitor the Research Animal Holding Facility (RAHF), a Space Shuttle payload that is used to house and monitor animals in orbit so the effects of space flight and microgravity can be studied. The techniques developed for the RAHF monitoring and diagnosis Expert system are general enough to be used for monitoring and diagnosis of a variety of other systems that undergo a Matrix FMEA. This automated diagnosis system was successfully used on-line and validated on the Space Shuttle flight STS-58, mission SLS-2 in October 1993.

Herrin, Stephanie↗
NASA NTRS2019

Hazards Analysis and Failure Modes and Effects Criticality Analysis (FMECA) of Four Concept Vehicle Propulsion Systems

The primary objective of this research effort is to identify failure modes and hazards associated with the concept vehicles and to perform functional hazard analyses (FHA) and failure modes and effects criticality analyses (FMECA) for each. Boeing also created a Fault Tree Analysis (FTA) for each of the concept vehicles, as the FTA contains the connectivity between systems and is an accepted, top-down method to analyze the safety of an air-vehicle. Conceptual design of notional powertrain configuration for each of four (4) NASA RVLT (Revolutionary Vertical Lift Technology) Concept Vehicles were developed in as much detail as was necessary to support the reliability and safety analysis for this project. Functional block diagrams from each of the conceptual powertrain configurations were created and used to order the FHA, FMECA, and FTA. Hazards were identified and the severity of each were categorized in the FHA for use in a follow-up FMECA. The FTA took inputs from the FMECA and the functional block diagrams to develop the connectivity and develop a quantitative architecture that could be used to perform sensitivity studies, as related to vehicle safety.Guidelines for reliability targets for both the air vehicle and the operation in the UAM (Urban Air Mobility) mission are discussed. An industry literature search was performed in order to assess gaps in existing government regulations and industry specifications. The industry literature search led to air-vehicle and operational reliability discussions, as related to Distributed Electric/Hybrid-Electric Propulsion (DE/HEP) system operating in the UAM role. A discussion of results and recommendations for future work is also provided.

Hazards Analysis↗
NASA NTRSDate not supplied

Synthetic Failure Mode Generation for Resilience Analysis and Failure Mechanism Discovery

Traditional risk-based design processes seek to mitigate operational hazards by manually identifying possible faults and corresponding mitigation strategies—a tedious process which critically relies on the designer’s limited knowledge. Resilience-based design, on the other hand, seeks to embody generic hazard-mitigating properties in the system to mitigate unknown hazards, often by modelling the system's response to potential hazardous events. This work adapts this approach to the traditional risk-based design process to synthetically generate hazardous modes, by representing them as a unique combination of internal component health-states which can then be injected and simulated in a model of the system failure dynamics. The design process may then reduce the risk of unknown internal hazards by iteratively mitigating the effects of these modes. The performance of this approach is evaluated in a model of an autonomous rover, where cluster analysis shows that elaborating the space of synthetic faults in the drive system using this approach uncovers a wider range of possible hazardous trajectories and failure consequences within each trajectory. However, this increase in hazard information comes at a high computational expense, highlighting the need for advanced, efficient methods to search and sample the hazard space.

Simulation↗
NASA NTRSDate not supplied

Synthetic Failure Mode Generation for Resilience Analysis and Failure Mechanism Discovery

Traditional risk-based design processes seek to mitigate operational hazards by manually identifying possible faults and corresponding mitigation strategies—a tedious process which critically relies on the designer’s limited knowledge. Resilience-based design, on the other hand, seeks to embody generic hazard-mitigating properties in the system to mitigate unknown hazards, often by modelling the system's response to potential hazardous events. This work adapts this approach to the traditional risk-based design process to synthetically generate hazardous modes, by representing them as a unique combination of internal component health-states which can then be injected and simulated in a model of the system failure dynamics. The design process may then reduce the risk of unknown internal hazards by iteratively mitigating the effects of these modes. The performance of this approach is evaluated in a model of an autonomous rover, where cluster analysis shows that elaborating the space of synthetic faults in the drive system using this approach uncovers a wider range of possible hazardous trajectories and failure consequences within each trajectory. However, this increase in hazard information comes at a high computational expense, highlighting the need for advanced, efficient methods to search and sample the hazard space.

Simulation↗
DOE OSTI2024

Full-field quantitative visualization of shock-driven pore collapse and failure modes in PMMA

The dynamic collapse of pores under shock loading is thought to be directly related to hot spot generation and material failure, which is critical to the performance of porous energetic and structural materials. However, the shock compression response of porous materials at the local, individual pore scale is not well understood. This study examines, quantitatively, the collapse phenomenon of a single spherical void in PMMA at shock stresses ranging from 0.4 to 1.0 GPa. Using a newly developed internal digital image correlation technique in conjunction with plate impact experiments, full-field quantitative deformation measurements are conducted in the material surrounding the collapsing pore for the first time. The experimental results reveal two failure mode transitions as shock stress is increased: (i) the first in situ evidence of shear localization via adiabatic shear banding and (ii) dynamic fracture initiation at the pore surface. Numerical simulations using thermo-viscoplastic dynamic finite element analysis provide insights into the formation of adiabatic shear bands (ASBs) and stresses at which failure mode transitions occur. Further numerical and theoretical modeling indicates the dynamic fracture to occur along the weakened material inside an adiabatic shear band. Finally, analysis of the evolution of pore asymmetry and models for ASB spacing elucidate the mechanisms for the shear band initiation sites, and elastostatic theory explains the experimentally observed ASB and fracture paths based on the directions of maximum shear.

42 ENGINEERING↗
NASA NTRS2011

Failure Modes in Capacitors When Tested Under a Time-Varying Stress

Steady step surge testing (SSST) is widely applied to screen out potential power-on failures in solid tantalum capacitors. The test simulates the power supply's on and off characteristics. Power-on failure has been the prevalent failure mechanism for solid tantalum capacitors for decoupling applications. On the other hand, the SSST can also be reviewed as an electrically destructive test under a time-varying stress. It consists of rapidly charging the capacitor with incremental voltage increases, through a low resistance in series, until the capacitor under test is electrically shorted. Highly accelerated life testing (HALT) is usually a time-efficient method for determining the failure mechanism in capacitors; however, a destructive test under a time-varying stress like SSST is even more effective. It normally takes days to complete a HALT test, but it only takes minutes for a time-varying stress test to produce failures. The advantage of incorporating specific time-varying stress into a statistical model is significant in providing an alternative life test method for quickly revealing the failure modes in capacitors. In this paper, a time-varying stress has been incorporated into the Weibull model to characterize the failure modes. The SSST circuit and transient conditions to correctly test the capacitors is discussed. Finally, the SSST was applied for testing polymer aluminum capacitors (PA capacitors), Ta capacitors, and multi-layer ceramic capacitors with both precious metal electrode (PME) and base-metal-electrodes (BME). It appears that testing results are directly associated to the dielectric layer breakdown in PA and Ta capacitors and are independent on the capacitor values, the way the capacitors being built, and the manufactures. The testing results also reveal that ceramic capacitors exhibit breakdown voltages more than 20 times the rated voltage, and the breakdown voltages are inverse proportional to the dielectric layer thickness. The possibility of ceramic capacitors in front-end decoupling applications to block the surge noise from a power supply is also discussed.

Liu, David (Donhang)↗
DOE OSTI2024

Interim Development of new Class B Code Case with Variable Design Lifetime and enhanced design rules to guard against cyclic structural failure mode

This report summarizes updates on the ongoing development of the new American Society of Mechanical Engineers Section III, Division 5, Class B rules to address the potential failure modes of Class B components. An initial design-by-analysis approach and supporting design rules are presented. The elastic-perfectly plastic (EPP) analysis approach has been adopted for primary stress limit and ratcheting check to prevent the component failure against the structural failure mode against primary load and strain accumulation due to cyclic loads. The creep-fatigue damage assessment uses explicitly defined elastic follow-up calculated from the stress concentration region of given component. Damage fraction calculation uses a novel coupled approach to capture the influence of the elastic follow-up and provide adequate conservatism for Class B components. The proposed Class B rules does not use the stress classification approach and uses the combined loads to assess component.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Multiscale Prediction of Yarn Pullout Failure Mode in Unreinforced Textile Fabrics

Unreinforced woven fabrics have been implemented in a variety of high performance applications, including body armor, deployable structures, and as the reinforcement material in composites. Multiscale modeling techniques have significantly improved the capabilities of simulation-based tools to capture fabric mechanics efficiently and accurately, but often lack in their prediction of failure and require pairing with finite element analysis (FEA) software, limiting their application to the design of ‘fit-for-purpose’ materials. NASA’s Multiscale Analysis Tool (NASMAT) is a standalone multiscale program that has been traditionally used in the analysis of reinforced composites materials. More recently, it has been amended to simulate unreinforced fabric behavior by allowing the geometric state of the tows to change with applied loading due to the lack of a reinforcement material, such as the matrix seen in composites. Previous work has shown the ability of NASMAT to capture nonlinear macroscale behavior by predicting geometric changes in the state of each subcell as a function of the applied loading and allowing each subcell in the analysis to rotate according to these predicted changes, as well as predict nonlinear behavior due to the fiber breakage failure mode. In this work, the capability of predicting the onset and propagation of failure in plain woven fabrics in NASMAT is presented for the yarn pullout failure mode, which occurs when a fabric is loaded at an off-axis angle relative to the warp of weft tow direction. Yarn pullout behavior is initiated by determining the applied load in which the shear resistance of the contact area between yarn families is overcome. When failure is initiated, yarn pullout is determined to have occurred when the applied displacement, calculated from global strain, exceeds the deformed position of a given contact points between yarn families, determined from pin-joint kinematics. Contact points where pullout has occurred contribute to a global damage parameter used to modify the homogenized stiffness of the fabric, resulting in nonlinear behavior observed at the macroscale. The off-axis loading behavior and yarn pullout failure theory have been developed and implemented into NASMAT such that users can simulate off-axis tensile behavior of fabrics in a single, standalone multiscale tool. Simulations are compared to uniaxial tensile tests at various off-axis angles to demonstrate the capability of the tool in its prediction of both the onset of failure at each off-axis angles and the stress-strain behavior as failure progresses.

Materials↗
NASA NTRS1972

Space tug propulsion system failure mode, effects and criticality analysis

For purposes of the study, the propulsion system was considered as consisting of the following: (1) main engine system, (2) auxiliary propulsion system, (3) pneumatic system, (4) hydrogen feed, fill, drain and vent system, (5) oxygen feed, fill, drain and vent system, and (6) helium reentry purge system. Each component was critically examined to identify possible failure modes and the subsequent effect on mission success. Each space tug mission consists of three phases: launch to separation from shuttle, separation to redocking, and redocking to landing. The analysis considered the results of failure of a component during each phase of the mission. After the failure modes of each component were tabulated, those components whose failure would result in possible or certain loss of mission or inability to return the Tug to ground were identified as critical components and a criticality number determined for each. The criticality number of a component denotes the number of mission failures in one million missions due to the loss of that component. A total of 68 components were identified as critical with criticality numbers ranging from 1 to 2990.

Boyd, J. W.↗
NASA NTRS1990

Tensile and compressive failure modes of laminated composites loaded by fatigue with different mean stress

Laminated composite materials tend to fail differently under tensile or compressive load. Under tension, the material accumulates cracks and fiber fractures, while under compression, the material delaminates and buckles. Tensile-compressive fatigue may cause either of these failure modes depending on the specific damage occurring in the laminate. This damage depends on the stress ratio of the fatigue loading. Analysis of the fatigue behavior of the composite laminate under tension-tension, compression-compression, and tension-compression had led to the development of a fatigue envelope presentation of the failure behavior. This envelope indicates the specific failure mode for any stress ratio and number of loading cycles. The construction of the fatigue envelope is based on the applied stress-cycles to failure (S-N) curves of both tensile-tensile and compressive-compressive fatigue. Test results are presented to verify the theoretical analysis.

Rotem, Assa↗